Search Documents

By W. L. Fink, L. A. Willey

This paper is the nineteenth of a series from the Aluminum Research Laboratories, presenting the results of the investigations of equilibrium relations in aluminum-base alloys made from electrolytically refined aluminum. In previous papers equilibrium relations have been determined and correlated for 12 binary systems. Equilibrium relations have also been determined for portions of the aluminum corners of three ternary systems (aluminum-iron-silicon, aluminum-magnesium-silicon and aluminum-copper-magnesium). The object of the present paper and those to follow is to increase our knowledge of the aluminum corner of the more important ternary systems. In 1926 Dix and Keith † suggested a new method for designating the phases encountered in alloy systems. The system has been used to a very limited extentl,2,3 The system has since been slightly modified and will be used in this and future papers. In the system as modified, a phase is designated by placing in parentheses the chemical symbols of the elements essential to the formation of that phase. The symbols in the parentheses are separated by dashes in order to clearly distinguish them from a chemical formula. Elements that are not necessary to the formation of the phase in question, but which may be present in solid solution, are not indicated in the designation. If two or more phases would have the same designation according to these rules, they are distinguished by prefixing Greek letters, and are definitely identified by X-ray diffraction patterns. Previous Investigations The solid solubility of magnesium in aluminum has been well established by the work of Dix and Keller4, Schmid and Siebe15, and Saldau and Sergeev6. There is no agreement as to the composition of the magnesium constituents at the aluminum end of the binary aluminum-magnesium system. Hanson and Gayler7 report Mg2Al3; Boyer8 found that the alloy

Jan 1, 1937

By L. A. Roe, E. A. Elevatorski

Wollastonite, named after William H. Wollaston, an English chemist, is a calcium metasilicate, CaSiO3; CaO: 48.30%, SiO2: 51.70%. It has a short history as an industrial mineral. The earliest production of wollastonite is reported to be from a deposit near Code Siding, located north of Randsburg, CA. At this locality small tonnages of wollastonite were quarried during 1933-34 and 1938-41, and processed into mineral wool. This operation was largely experimental and virtually no United States production was again reported until the 1950s when a large deposit near Willsboro, NY, was developed by the Cabot Corp. A processing plant was placed onstream in 1953, with nearly continuous production to date. It is currently operated by NYCO, a division of Processed Minerals, Inc. Since 1958, wollastonite deposits in the Little and Big Maria Mountains of Riverside County, and in the Panamint Range of Inyo County, both in California, have operated intermittently for production of both ornamental and commercial wollastonite. During 1980, the United States was the major producing country, furnishing about 75% of the world's output. Current production comes from Finland, Mexico, India, and Kenya. Small amounts have been shipped intermittently from the USSR, New Zealand, Republic of the Sudan, Republic of South Africa, and Namibia (South-West Africa). The principal use of wollastonite is in the manufacture of plastics. Other uses are for paints, ceramics, adhesives, fluxes, glazes, thermal insulation board, and refractory products. Mineralogy Pure wollastonite, CaSiO3, has the composition of 48.3% CaO and 51.7% SiO2. However, it is seldom found in the pure state due to the ease with which it takes into solution the metasilicates of manganese, magnesium, iron, and strontium. Predominantly, wollastonite occurs as a contact metamorphic deposit forming between limestones and igneous rocks. Commonly associated minerals are garnet, diopside, epidote, calcite, and quartz. It has a specific gravity of 2.8 to 3.0, and hardness of 4.5 to 5 on Mohs' scale. When pure, it has a brilliant white color, but with impurities it may be grayish or brownish. Luster is vitreous to pearly. Melting point of wollastonite is about 1540ºC. Wollastonite occurs in coarse-bladed masses, rarely showing good crystal form. It is usually acicular or fibrous, even in the smallest of particles. The most unique property of crushed and ground wollastonite is its cleavage. Fragments of crushed wollastonite tend to be needle-shaped, imparting a high strength, and this property is the basis for many of its uses. The fiber lengths are commonly in the ratio of 7 or 8 to 1, length to diameter. The average diameter of wollastonite is 3.5 µm. Some crystals of wollastonite fluoresce under short-wave or longwave ultraviolet light, or both, with colors ranging from yellow-orange to pink-orange. Specimens may also show phosphorescence. The acicularity of wollastonite is a property of considerable importance to the marketplace. The plastics industry makes utilization of high aspect ratio grades of wollastonite (20:1) for reinforcing thermoplastics and thermoset polymer compounds. The naturally high pH of 9.9 (10% water slurry) is a prime property to the coatings industry. The coatings industry uses milled grades of wollastonite as a pH stabilizer in interior and exterior PVA and acrylic latex systems. Processed wollastonite can have a G.E. brightness of 90 to 93. Chemically, wollastonite is inert and this property makes it useful as a filler and reinforcing agent. There are two polymorphs of calcium silicates: wollastonite, a low temperature form, and pseudowollastonite, a high temperature

Jan 1, 1983

My predecessor in the office of President of the Institute started a custom of visiting the various local sections, thus obtaining their points . of view and their ideas as to how the Institute can best serve the interests of its members. Exceedingly valuable- exchange of ideas was thus brought about. I am following this custom as far as the limited amount of free time at my disposal will allow me, and I trust that my successor in office will appreciate the benefit to be derived from following the custom thus initiated and will continue the swing around the circle of the local sections. The activities of the Institute are increased by the prestige gained from large numbers and I trust that every member of this local section will consider himself a member of the committee on increase of membership and will see if he is not able during the coming year to gain at least one new member for the Institute. This is a perfectly possible proposition for, although the membership of the Institute is at present approximately seven thousand, I feel sure there are at least seven thousand more men in the United States who are interested in mining, metallurgy or geology from the metal-mining point of view who would make admirable members or associate members of the Institute. The first consideration of the Institute as a body, and of each member as an individual, is to win the war and defeat the Huns. In order to accomplish this, the Institute, as a body, has cooperated with the other national engineering societies and the great bureaus of the Department of the Interior, the United States Geological Survey and the Bureau of Mines in forming committees to study and advise the Government on pressing problems of vital importance.

Jan 5, 1918

By Franklin Moeller

Considering the really short time that has elapsed since hydro-metallurgical processes of extracting copper from ores have been extensively developed, and the large scale on which this method is practised at Ajo, the successful operation of the plant must excite the admiration of every visitor. The application of the mechanical unloader to the purpose for which it is employed at Ajo is but an extension of the use for which it was originally designed, some 20 years ago, for unloading iron-ore vessels at the lower lake ports. At a time when the maximum output of a single machine, with men shoveling the ore into buckets, did not exceed 40 tons per hour, G. H. Hulett invented and constructed a mechanical unloader with a bucket of 10-ton capacity. This machine was of the steam hydrauIic type, and it is still in operation after nearly 20 years of service. Several more machines of the same type were built, but the difficulties of power transmission, and the rapid development of electrical machinery, soon led to the adoption of electrically operated machines, and practically all of the later installations have been thus equipped. This electrically operated unloader has proved so well fitted for the work that the design of the lake boats has been practically revolutionized, with special view to the ease and rapidity of unloading. It is now possible to unload a 12,000-ton vessel with four machines in a little over 2 hr. This has necessitated an increase in the capacity of the machine, and the largest yet built handles an average load of 17 tons, with a possible maximum of 20 to 21 tons. The Ajo excavator is somewhat simpler in design than the iron-ore unloader, in that it is not provided with a larry. In the unloader, the iron ore, picked up by the bucket, is delivered to a larry or transfer car which runs in the lower chord of the bridge; the larry then delivers the ore either into railroad cars, standing on several parallel tracks, or into the stock pile, thereby saving the time that would be required for the bucket to make the trip. At Ajo, the bucket delivers the tailing

Jan 1, 1920

By C. H. Jr. Herty

ALMOST every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gaug-ing of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanli-ness of forging steels, both carbon and alloy. In this problem the oxidiz-ing characteristics of the slag are of prime importance.

Jan 1, 1940

By C. L. Berrien

Before the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent's office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day's pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed, the men being paid monthly. In some cases, fairness to the employee was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines. Changes in Stoping Methods Early in 1916, W. B. Daly, then general superintendent, and the author, then assistant general superintendent, visited the Southwest mining districts with the object of finding some improved mining

Jan 1, 1923

By C. L. Berrien

Before the present company was formed, in 1916, each group of mines comprising the old organizations made its detailed daily and monthly mine cost records along the lines used before the consolidation; that is, there was no attempt made to standardize and compare the stope costs of all mines. The general cost sheets for all mines, however, were standardized, and cumulative labor cost sheets were compiled in the general superintendent's office. At most of the mines, a daily record or distribution sheet for each working place was kept, showing the number of men, hours of drilling, hours of timbering, hours of tramming, cars of ore, cars of waste, sticks of powder and feet of fuse. This information was kept by each shift boss and entered on the distribution sheet by him or, at some mines, by a tram boss. The superintendent solved his own problems under the direction of the general superintendent, but without coming in touch with other superintendents, either through records or general conferences. Probably 95 per cent. of the stopes were square-set worked by day's pay; there were some back-filling and shrinkage stopes. Many of the development places, such as shaft sinking, station cutting, drifting and raises had always been run by contract. These contracts were given, for no definite period, at so much per linear foot and were measured monthly, or when completed, the men being paid monthly. In some cases, fairness to the employee was not maintained. On the whole, there was no standardization. There were no stope contracts, because of the objections of the Western Federation of Miners to general contracting in the mines. Changes in Stoping Methods Early in 1916, W. B. Daly, then general superintendent, and the author, then assistant general superintendent, visited the Southwest mining districts with the object of finding some improved mining

Jan 1, 1923

By Charles H. Fulton

There are comparatively few accurate data on the melting-or the freezing-point temperature of metallurgical slags, or on related physical phenomena, such as fluidity near the melting-point, specific heat, latent heat, etc. With the exception of the work of H. 0. Hofman,' and some older work by R. Akerman, P. Gredt, and H. M. Howe, no information is available that is of direct interest to the metallurgist. Hofman's valuable work is the only one that refers to slags produced in the metallurgy of copper and lead. The classic work of J. H. L. Vogt,2 who views slags from the standpoint of physical mixtures (solutions in which the entities are minerals), has opened up a new field in the study of slags, and has placed the investigation of such properties as melting-temperatures, etc., on a rational basis. The recent work of A. L. Day, E. T. Allen, and W. I?. White, of the Carnegie Institution, at Washington, and of European investigators3 on certain systems of silicate minerals confirms the value of the investigation of silicate series from this standpoint, and it is my aim to apply this method to metallurgical slags, in order to gain exact data of value in metallurgy. The work recorded in the present paper is the result of an investigation of reverberatory-furnace slags made for a Western smelting company to determine exactly the influence of change in composition, within comparatively narrow limits, on the melting-point. For a general discussion concerning the mineralogical character of slags and the principles on which this investigation is based, reference should be made to other work: for the subject is too large to be stated in this paper, except very briefly in the following outline:

Jan 1, 1913

By Cyril Smith

ALTHOUGH not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical conductivity and that it can therefore be calculated from the latter. The Wiedemann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys-particularly those containing nickel-and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are, needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only.

Jan 1, 1930

By R. U. Jackson

FACED with rising costs, the mining industry is looking to new methods and equipment to supply the relief necessary for profitable operation. Conveyor transportation is rapidly taking a superior position to motor tramming in underground mines because of lower installation, maintenance, and operating costs. Haulage is always a critical problem in underground mining. The ease of operation and flexibility of a haulage system can have an important effect on ultimate mining cost. With the average tenor of ores on the downgrade, larger tonnages are required for the same metal recovery. This selection of a tramming system can be the key to a successful, paying plant. Because this shift is being made at an ever advancing rate, it may become necessary to tailor mining operations to the transportation system, rather than to select a haulage system fitting set mining methods. In choosing a haulage system, the relative costs of the various methods are of the greatest importance. Adapting the mine to one or the other type of tramming is not considered in the cost analysis, and very likely would make little difference, outside of location of drifts and raises. In the cost sheet, the problem presents recommendations for a conveyor installation and a comparison of equipment, installation, operation, maintenance, and power costs are made. Under the track haulage estimate, no allowance was made for dumping equipment at the shaft pocket or bin. If this equipment was added to the balance sheet, the additional

Jan 1, 1952

By John S. Johnson

THE purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. LININGS FOR BOREHOLES The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used, particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1941

THE CHAIRMAN (G. H. CLEVENGER, Stanford University, Cal.).¬I would like to ask Mr. Pyne if he has had any experience inn the use of chromite as refractory under conditions that are highly reducing? I am reminded of an experience I once had with an electric furnace. I imagined that chromite would form a splendid lining, but it soon disappeared; hence it seems probable that, under highly reducing conditions at a high temperature, chromite is a very poor refractory. F. R. PYNE.-In copper smelting the atmosphere is generally neutral, or slightly oxidizing; we do not use highly reducing atmospheres at all, not even in the matting furnace. You can take the chromite brick and treat it as you would an iron ore, obtaining ferro-chrome very readily, from which the copper will separate. We have done this; in fact, at one time we considered installing a small electric furnace for the production of ferro-chrome. FOREST RUTHERFORD, New York, N. Y.-During the time I was general superintendent at the smelter of the Copper Queen Consolidated Mining Co., at Douglas, Ariz., a great many experiments were made on the furnaces and settlers with different kinds of brick, and I agree with Mr. Pyne's statements about chrome brick. Their power to absorb metals is very great, and as they cannot be smelted at any temperatures obtainable in a copper furnace, to get rid of the bats and extract the metal from them is quite a problem. We finally got down to using chrome brick only for lining the settlers, out of which we often got a life of upwards of 2 years, and for lining the blast-furnace bottoms, for the reason that chrome brick can be heated and wet, or wet after being heated, without going to pieces, whereas under these conditions magnesite brick will break down very rapidly. We also used a layer of chrome brick above and below an 18-in. band of magnesite brick put on the slag line of the reverberatories, in order to separate the magnesite from the silica brick, fearing that they would slag each other and let the wall drop. The idea worked, but became unnecessary on account of a change made in the method of feeding the furnaces. Chronic brick will not stand up under pressure so well as a good Grecian or Austrian magnesite brick, on account of the poorer bonding properties of the materials from which the chrome brick is made.

Jan 4, 1918

By R. Schuhmann

Available thermodynamic data applicable to copper smelting systems are collected and tabulated, and the important gaps are pointed out. A few examples are given of estimations which can be made from the available data. An experimental research program is proposed to supply the thermodynamic data that appear most essential to better quantitative understanding of the chemistry of copper smelting. The proposed program is designed also to shed specific light on the practical problems of slag losses and magnetite behavior. OPPER smelting, from flotation concentrates to V-/ blister copper, is conspicuous among the large scale chemical processes which are conducted with only relatively incomplete knowledge of the physical chemistry involved. For example, no common metallurgy text explains adequately why copper enters the matte phase while iron enters only to the extent that sulphur is left over after satisfying the copper. Explaining this important phenomenon as a manifestation of the greater affinity of sulphur for copper than for iron is unsound because the affinities of copper and iron for sulphur are about the same at smelting temperatures. As will be shown, other affinities are really decisive in the relatively clear-cut separation of copper in the matte. In contrast, thermodynamic studies have contributed much to our understanding of copper refining, zinc oxide reduction, magnesium production, steelmaking, etc. For each of these processes, the important reactions are clearly recognized, and fair to good quantitative values of the free-energy changes and equilibrium constants are available. Such data have proved to be of constantly increasing practical value in process development and improvement. Work in other fields has furnished much thermodynamic data applicable to copper smelting systems. In fact, several promising starts have been made in applying such data to specific smelting problems. Kelleyl made an appraisal of the possibilities of recovering elementary sulphur from low grade matte. His calculations and compilations of thermodynamic data have represented the starting point for much of the work in this field, including the present survey. Huang and Hayward2 nd Aksoy3 used thermodynamic methods in the study of copper losses in reverberatory slags. Peretti4 used thermodynamic data in explaining the chemistry of converting. The recent publications of Darken and Gurry"." and of Darken,' dealing with the iron-oxygen and iron-silicon-oxygen systems, respectively, present equilibrium data that are applicable to copper smelting systems. Also additional data were reported recently on the affinity of sulphur for copper, manganese, and iron8 and on the sulphur pressures of iron-sulphur melts." The survey presented in this paper was made as the basis for planning an experimental program on the thermodynamics of copper smelting. Few researches on the chemistry of copper smelting have been reported in recent years, so that a reappraisal and coordination of old and new data are essential if further work is to take the directions of maximum value. The experimental program is now in progress, and the plan of attack is outlined at the end of this paper. Progressive Oxidation and Desulphurization of Copper-bearing Liquid Phases: The chemical activities of sulphur and oxygen are two of the most important thermodynamic yardsticks to be applied to copper smelting processes. Virtually the entire smelting and refining sequence involves a series of systems characterized by decreasing sulphur activity and increasing oxygen activity. In this section, therefore, an attempt is made to define and explain these activities in terms of equilibrium partial pressures of SO2, s2, and O,. Also, estimates of these quantities are presented, the estimates being based largely on calculations presented in a later section of this paper. The sequence of steps from raw flotation concentrate to fully oxidized copper ready for poling involves progressive and controlled oxidation. Iron is oxidized and enters the slag. Sulphur is oxidized and leaves in the gas. Table I summarizes several important features of this oxidation and desulphurization sequence, starting at the beginning of the matte blow in the converter. The top line gives in order the principal smelting and refining stages up to fully oxidized copper, plus the additional step, not used commercially, of oxidizing all the way to Cu,O. In the second line are shown the principal copper-bearing liquid phases which characterize the process. Through most of the sequence the copper

Jan 1, 1951

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties situated at 29 West 39th Street in New York City United Engineering Trustees, Inc. When Mr Carnegie made his gift, "for the erection of a suitable union home" for the engineering societies, United Engineering Trustees, Inc (then United Engineering Society) was chartered un¬der Chapter 703, Laws of the State of New York, 1904, for "the advancement of the engineering arts and sciences in all their branches, and to maintain a free public engineering library " The Corporation was further empowered to acquire real and personal property and to use, maintain and occupy it, with the provision that any building erected by the Corporation shall be used perpet¬ually as a meeting place and headquar¬ters for the Founder Societies Thus the Carnegie gift realized the ideal of bring¬ing the engineering societies together under one roof, and the Corporation through its members nominated in equal numbers by the four Founder Societies had the necessary authority to act for the Founder Societies in their joint in¬terests in owning and operating for them not only Engineering Societies Building, but in the course of time, Engineering Societies Library, and The Engineering

Jan 1, 1952

By A. E. Moss, J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing. By 1954 iron ore will begin to move towards American blast furnaces, and shortly thereafter the annual rate of production is expected to reach 10 . million tons. To bring this vast project into being over $200,000,000 will have been spent for exploration and development, mining equipment, hydro plants, townsites, the building and the equipping of . a 360-mile railroad, and the construction of docks and ore-handling facilities. The most important iron ore deposits are located over 300 miles from tide water, see frontispiece and also Fig. 1. The frontispiece shows principal sources of iron ores and manganiferous iron ores for the U. S. and Canadian steel industry, and the major smelting districts are shaded on the map. No navi- gable rivers lead into the interior. When work was . commenced on this project there were no roads, no railroads, no communication ,system, no inhabitants, and no adequate maps either topographical or geological. The geological field season was limited to approximately 100 days per season. The obstacles facing this enterprise were many and varied. Its success will be due to the integrated team work of people of diverse skills. Explorers, Indian guides, prospectors, geologists, surveyors, mechanical, civil, electrical, and mining engineers,

Jan 1, 1954

By G. H. Clevenger

THE reagents now used in flotation consist of various acids or salts, which may be either electrolytes or non-electrolytes, dissolved in water and some substance or combination of substances which function as collecting or frothing agents. At times the only dissolved salts present are those naturally occurring in the water used. The general effect of the electrolyte is to greatly sharpen the separation between the gangue and the concentrate. Examples of this are: The use of sulphuric acid with zinc ores; and of sodium carbonate or calcium oxide (line) with silver-gold ores. Crude pyroligneous acid is also sometimes used when available. Various oxidizing agents, such as permanganates, bichromates, etc., are added in the selective flotation of lead-zinc ores. Many other reagents for performing certain specific functions, either real or imaginary, have been proposed, and a number of them have been tried upon a working scale. The wild orgy of experimentation which is now going on in flotation exceeds even that which followed the introduction of the Washoe process for the treatment of Comstock ores, when, among other things, sage-brush tea and tobacco juice were reagents added to the pans. Out of all this will, of course, eventually come a more or less standard practice for the treatment of each class of ore. Omitting a discussion of the functions of frothing and collecting agents, the reagents used in flotation for this purpose may be classified under five general heads: (1) Essential oils; (2) fixed or fatty oils;. (3) alcohols and their combinations with organic acids; (4) coal tar and its refined products; (5) petroleum and its refined products. A flotative agent of some kind is required in flotation as now practiced. A single reagent, as, for example, certain. of the essential oils, may perform the dual function of frothing and collecting agent, or a mixture of substances may be required.

Jan 9, 1916

By George Kunz

(Butte Meeting, August, 1913.) . THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World's Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact. that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it-would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct. weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.2

Jan 7, 1913

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inor-ganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of furnaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the produc-ing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the struc-ture. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate.

Jan 1, 1937

By William Kelly, F. H. Armstrong

The object of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the results of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912. Generating PoweR Plants After the success of electrical operation was assured, a second set of water wheels and generator was installed at the falls, for which provision had been made in the original design and in the construction of the foundations, and later three additional wires were added to the main transmission line, doubling its capacity and reducing the line loss. The general conditions of this installation are particularly favorable for hydro-electric operation. In the neighborhood of three-fourths of the power used is for mine pumping, which in the main is regular and continuous. For air compressing, power is used for about 18 hr. a day for five days, and 9 hr. for one day in the week, though occasionally when shaft sinking is going on a very small amount of compressed air may be

Jan 1, 1915