Search Documents

By J. J. Jonas, G. Gagnon

SHG zinc was extruded in the temperature range 110" to 350°C and the strain rate range 0.05 to 5 sec-1 The strain rate/flow stress/temperature results were analyzed using a power sinh stress relationship. When temperature changes due to the heat of deformation and to heat losses are neglected, the exponent of the sinh function of the stress is 5.6, and the apparent activation energy of deformation is 28 kcal per mole. When these changes are taken into account, the exponent decreases to 4.7 and the activation energy to 23 + 2 kcal per mole. The corrected stress exponent and activation energy are in very good agreement with published values obtained from creep experiments, and suggest that the hot extrusion of zinc is controlled by a mechanism involving self-diffusion. When the extrusion and creep data are compared using a Zener-Hollomon parameter and either a sinh or an exponential stress term, an appreciable offset is observed, which may be due to the difference in impurity content. For a given set of extrusion conditions the ram speed, maximum pressure, and initial temperature can also be correlated using a Zener-Hollomon parameter and a sinh pressure term. THE deformation of metals at temperatures over about one-half the absolute melting temperature has been extensively studied at creep strain rates. By contrast, relatively little work has been carried out on the behavior of metals at hot working strain rates. Most of the latter investigations have been performed using simulative methods, such as hot torsion and hot compression, in which the friction conditions and temperature rise during deformation may differ appreciably from those existing under industrial conditions. Recently, however, Wong and Jonas1 used a scaled-down industrial process to determine the stress and temperature dependence of the strain rate during the extrusion of aluminum. In such tests, the effects of friction and adiabatic heating are closer to those produced in industrial operations. Also, with regard to the testing of materials of limited ductility such as zinc, hot compression and hot torsion do not permit the attainment of true strains as large as the deformations usually applied commercially. The present study was undertaken to investigate the extrusion behavior of Special High Grade (SHG) zinc. The detailed objectives were: 1) to establish the stress and temperature dependence of the strain rate with and without a consideration of adiabatic heating, 2) to study the pressure and temperature dependence of the ram speed, and 3) to investigate the microstruc- tural changes occurring during the deformation. The last aspect of the investigation will be covered in a separate paper. The treatment described below differs from that of Wong and Jonas in that the adiabatic temperature rise during deformation is taken into account, and the calculation of the mean equivalent strain rate is based on the redundant as well as on the homogeneous work. EXPERIMENTAL PROCEDURE Rods from two shipments of continuously cast SHG zinc* were used in the investigation. The composition *Supplied by courtesy of Cominco Ltd. range of the impurities present, as given by the supplier, was: Pb: 0.0013 to 0.0023 pct, Fe: 0.001 pct max Cd: 0.0001 to 0.0006 pct, Cu: 0.0002 to 0.0005 pct, Ti: 0.0001 pct max; thus, by balance, zinc valued from 99.9963 to 99.9966 pct. The as-received rods were machined into billets having a nominal diameter of 1.56 in. and a nominal length of 1½ in.; longer billets up to 4 in. in length, were also used to investigate special aspects. The as-machined rods were annealed at 400°C for 24 hr and slowly cooled. This treatment produced a columnar grain structure, with a grain size of about $ by 2½ cm which was appreciably larger than the as-cast one. A 150-ton, direct extrusion, vertical press was used. Ram displacement and force were recorded continuously against time. A constant flow control valve permitted the maintenance of a range of preselected ram speeds up to in. per sec. The selected speed was held constant, irrespective of the required force, as long as the load developed was below the maximum available. Strain gages were used to determine the force; the gages were calibrated before and after each testing period with a 200,000-lb capacity load cell. Further details of the experimental equipment can be found in Ref. 2. The billets were preheated for 90 min in the extrusion container, which was well insulated so as to minimize temperature gradients. This period was sufficient for the billet to reach a uniform temperature at all temperatures between 110" and 350°C. A square-shoulder die having a 0.290-in. diam central hole was used. The extrusion ratio was 30 to 1. This is equivalent to a reduction in area of 96.7 pct, an elongation of 2900 pct, and a true strain of 3.4. The ram speed was varied over two orders of magnitude from 0.0027 to 0.26 in. per sec. The ram was water-cooled during most of the tests, although some experiments were conducted with a preheated, uncooled ram. All extrusions were run without lubricant, which resulted in conditions of sticking friction. EXPERIMENTAL RESULTS Stress Dependence of the Strain Rate Neglecting Adiabatic Heating. The maximum force required to extrude is given in Table 1 for each of the five initial

Jan 1, 1970

The visitors to the October meeting will be given opportunity to visit the coal fields in Illinois, adjacent to St. Louis, the steam-shovel operations near Pittsburgh, Kan., and the Oklahoma oil fields. The coal mines of Illinois, Missouri, Kansas, Oklahoma and Arkansas furnish fuel over all of the central region of the country. Especially at this time, this district is of importance because of the necessity of producing enormous quantities to meet the country's demand. Some of the mines produce as much as 5,500 tons in 8 hr., and. the total output of Illinois, alone, in 1916, was 63,000,000 tons. Visitors may see elaborate underground electric tram systems, large underground machine repair shops, surface plants equipped for rapid loading, and some of the most modern coal-washing installations. The conditions for mining here are somewhat simpler than in the east.

Jan 8, 1917

By D. K. Deardorff, H. Kato

THE transformation temperature of hafnium from hcp to bcc is 1750° + 20 °C in contrast to previously published values by Duwez and fast2 which are believed inaccurate. The Bureau of Mines determined this value by measuring the temperatures at which a sudden decrease was observed in the electrical resistance of hafnium alloys containing up to 18 at. pct Zr, and then extrapolating the temperatures to 0 pct Zr. Duwez1 previously reported a transformation temperature of 1310°C, obtained by use of a rapid-cooling thermal-analysis technique. Later, Fast2 published a much higher value of 1950° 100°C based upon: a) his own determination of 1690°C for the beginning of the transformation range for hafnium containing 5.7 at. pct Zr, and b) his belief that lattice parameters reported3 for Duwez' hafnium indicated i contained 19 at. pct Zr and that the 1310°C value should be associated with that composition. Russell4 subsequently stated that Duwez and Fast probably were reporting their lattice parameters in different units and reassigned a value of 6.0 at. pct Zr to Duwez' hafnium. If this assumption were true, Duwez' hafnium was of approximately the same purity as Fast's, but his transformation value was considerably lower. The reason for this divergence is not known. Fast's value for hafnium containing 5.7 at. pct Zr agrees well with our data. McGeary5 determined a transformation value of 1660°C by metallographic examination of heat-treated specimens, but the zirconium content of his hafnium was not definitely established. The specimens used in this investigation were 1/8-in.-diam rods 6 1/2 in. long, fabricated by hot-swaging bars cut from arc-melted buttons. These buttons were melted from crystal bar hafnium and crystal bar zirconium. The chief impurity in the hafnium

Jan 1, 1960

By AIME AIME

THE 130th Meeting of the Institute was held in Birmingham on Oct. 13 to 15, with visits to other mines and districts before and after. The last visit of the Institute to Birmingham was made in 1888, thirty-six years ago, and vast development has been made in' the district since then. With proverbial southern hospitality compounding over this period of years the welcome given to the Institute was such that .it is difficult to express properly the gratification and appreciation of the visiting members and the officers of the Institute. The Birmingham News in an editorial said: Birmingham is duly appreciative of the presence of these gentlemen, not because they are all distinguished in their great services in the mining and metallurgical world, but for the further reason that our interests are very largely wrapped up in their deliberations. Birmingham is one of the great industrial centers of America. Their discussions are of vital concern to all of us.

Jan 1, 1924

By G. G. Marino, J. W. Mahar

This paper provides an understanding of the behavior and potential damage of homes resulting from sag-type mine subsidence. This is done with extensive research of numerous case histories in Illinois collected by the authors. The house response to subsidence-induced ground displacements are summarized and evaluated. A damage level criteria, specifically developed for residential structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 1, 1986

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerksdorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7988 acres or 12.5 sq miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26-ft diam down-cast shaft and a 22 ft-diam up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month. To exploit the Eastern zone of the property and assist in increasing production to 200,000 tons milled per month, it was decided to sink a further Twin Shaft System consisting of a 28-ft diam downcast shaft and a ventilation up-cast shaft -22-ft in diam, both monolithic concrete lined — 200 ft apart and 5300 ft deep. This paper deals with the sinking and commissioning of these Eastern Twin Shafts. This was achieved by one sinking crew within a period of 20 months. A) PLANNING 1) Siting: The Eastern Shaft System was sited in the north-east area of the property, 12,000 ft east on strike from the Pioneer System. (Fig. 1). Initially the system was sunk to the 5300 ft elevation to conform with the original Pioneer Shaft System. On completion a sub-vertical main shaft will be sunk to the 8000 ft elevation in the immediate vicinity, and subsequently the surface ventilation shaft will be deepened to this elevation by raising from level to level and sliping to full size. The exact positions of the shafts were chosen after: a) underground development had located certain known water bearing zones, and b) geophysical and topographical surveys had been carried out. The shafts passed through the following geological succession: Surface to 4430 ft - Dolomites of the Transvaal System 4430 to 4470 ft - Quartzites and conglomerates of the Black Reef Series of the Transvaal System. 4470 to 4470 ft - Diabasic Lava of the Venters-dorp System (Ventersdorp Contact Reef at base). 4470 to 5250 ft - Quartzites of the Elsburg Series of the Upper Witwaters-rand System. The shafts were sited to ensure that the least possible water would be encountered during sinking, and this contributed to the rapid rate of sinking. 2) Duties: a) The 22-ft diam ventilation shaft was designed to up-cast 1,400,000 cfm of air (0.060 density) against a resistance of 22 in. water gauge. b) The main shaft was designed to handle 160,000 tons hoisted per month as well as the men, material and down-cast ventilation to serve this tonnage. The 284 diam main shaft is equipped with streamlined buntons spaced at 15 ft centers set in pockets which were left during sinking. There are six compartments, four of which are sewed by two dual purpose hoists, hoisting either, twedeck man cages or 13-ton bottom discharge skips. The other two compartments are served by a single purpose winder hoisting double deck cages accommodating 60 men per deck. (Fig. 2). 3) Timing: Permanent equipment was ordered well in advance to insure continuity in the operation. Development underground reached the shaft positions before the start of sinking operations. From this development, boreholes were drilled into shaft positions to drain off water in the vicinity of the shafts. To ensure complete co-ordination of effort, all relevant data, as well as the allocation of responsibility, were made known to all persons and departments concerned. 4) Models: The extensive use of scale models during the preliminary planning stages proved most useful in deciding on design such as buntons, bunton pockets and guide cleats, and complex layouts concerning loading, spillage and pumping arrangements. (Fig. 3). These models also proved invaluable in determining the walling routine. Normal working conditions could

Jan 1, 1964

By Paul M. Tyler

OF THE 92 elements generally accepted by chemists as constituting the primary building blocks of matter, all but the very rarest have been investigated with a view to employing them in steel manufacture. The surprising thing is that so few have been found commercially acceptable. Despite the relatively small number of elements involved, the use of alloys in steel making is one of the most complicated and probably one of the least well understood of modern industrial enterprises. The action of individual elements in steel making has been described often and a profuse and somewhat acrimonious literature covers pretty much the whole field of ferroalloy ore supplies. In the middle ground between the miner and the -steel maker developments are less carefully watched by most observers and except for an occasional description of the technique of some conversion process or the tariff hearings in Congress, little is said about them. The present paper has been submitted in the hope that it will stimulate broader constructive economic thinking. It undertakes to describe in' relatively nontechnical terms this great and growing though highly complex industry and to study its relations to national progress.

Jan 1, 1932

Jan 1, 1962

By R. J. Stevens

THE Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft (1934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace 6 (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (1) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases'in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led' to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory . furnaces in terms of tons of copper produced per ton of coal burned is high.. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table , shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is sufficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 2 2 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1947

By Howard Martens, Pol Duwez

XPERIMENTS were performed on a Cr-Fc alloy Econtaining 44.7 pet Cr in order to determine the heat evolved during the transformation of the a solid solution into the s phase, and the change in volume accompanying the transformation. Since previous measurements on the rate of formation of a from s indicated that the reaction was quite fast as soon as the equilibrium temperature of 820°C was exceeded by some 50°, standard thermal analysis experiments were performed on heating specimens of s at the rate of approximately 40°C per sec. A definite thermal arrest was observed at 870"C, Fig. 1. This result indicates that the reverse seaction of into a is exothermic. From the heating curve of Fig. 1, taking 15°C per sec as the heating rate in the neighborhood of the transformation, 2.4 sec as the time for transformation, and assuming that the specific heat of the alloy at 850°C is an average between iron and chromium, namely 9.5 cal per mol per "C, the latent heat of transformation is approximately 342 cal per mol. The order of magnitude of this latent heat was also obtained by comparing the heating curve of Fig. 1 with a similar curve obtained with pure iron under identical experimental conditions. It was found that the length of the thermal arrest for s was about 1.8 times as long as that for iron. Since the latent heat of the a to 7 iron transformation is 203 cal per mol1, 2 the latent heat of it to a would be 365 cal per mol, which is in relatively good agreement with the value determined from the heating curve. For the determination of volume change, thermal expansion curves were recorded using a specimen containing 44.7 pet Cr and completely transformed to cr by previous treatment. The curves were recorded at a rate of heating of about 4°C per min and at approximately 840°C a sharr, increase in length of about 0.08 pet took place. Fig. 2. It is therefore established that the specific volume of a near the transformation temperature is about 0.24 pet smaller than that of a, and consequently, when the s phase forms in an a matrix, it would tend to shrink away from the matrix. Since the s phase is known to be extremely brittle, these results offer an explanation for the microscopic cracks often observed in the a phase under the microscope. The results of this study are in qualitative agreement with previously published data on stainless steel 19-9DLa and on a Cr-Fe alloy containing 45 pet Cr.' The increase in density due to the transformation from n to s given in ref. 4 is 0.90 pet. These measurements, however, were made at room temperature. whereas the presently reported 0.24 pet is the change at the temperature at which the transformation takes place during heating. In the graph of Fig. 2, the percentage change in length that would be observed at room temperature is given by the length X, which is about 0.27 pet. This would correspond to 0.81 pet in volume change. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-ORD-18 with the Army Ordnance Corps, Washington, D. C. The authors wish to thank this agency for permission to publish the results of this investigation. References I H. Klinkhardt: Measurements of True Specific Heats at High Temperatures. Annalen der Physik (1927) 84, pp. 167-200. - H. Esser and W. Runghardt: Influence of the Method, of Dctcrmination on the Measured Heat Content of Iron. Archtvo ffur Dct Eisenhiittenwesen 11934) 8, pp. 37-38. J. J. Gilman, P. K. Koh, and 0. Zmeskal. Delta Ferrite Formation and its influence on the Formation of Sigma in a Wrought Heat Resisting Steel. Trans. ASM 1 1949) 11, pp. 1371-1388. 1 J. M. Thomas: Discussion of ref. 3. Trans. ASM (1949) 41, pp. 3 390-1392.

Jan 1, 1957

By AIME AIME

ON May 5, the Washington, D. C., Section, A.I.M.E., devoted its meeting to the many-sided and perplexing question of mineral stock-piling for peace. Opening the symposium, Harry J. Wolf, of the War Production Board, outlined the problem under six heads: (1) Technical. Mechanical, chemical, or metallurgical importance of specified materials, emergencies that might arise, relative scarcity, and critical value of stock piles during emergencies. (2) Economic. Cost to Government, influence of Government stocks on commercial relationships and markets, effect of availability of items as a con¬structive influence on industry, Administration policies now and during postwar period. (3) Legislative. Need for immediate legislative action, need for legislation on postwar conditions as well as on current requirements, a constructive basic policy to prevent political manipulation. (4) Military. Consideration of re¬quirements and supplies bearing on national safety and needed for manufacture of equipment, and adequate reserves of scarce materials for research or experimentation by military agencies. (5) International. Interests of the United Nations in contradistinction to those of the United States; effects of nonisolation policy on nature, location, and administration of stock piles. (6) Negative stock-piling. Question of United Nations' legislation to prevent stock-piling by Axis nations after the war and who shall purchase stock-pile materials and during what periods.

Jan 1, 1943

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack.

Jan 1, 1949

By E. C. Burke, W. R. Hibbard

Plastic deformation in magnesium single crystals was studied by tensile tests at room temperature utilizing an improved preparation and testing technique. Consistent critical resolved shear stress values for basal slip were obtained. The advent of pyramidal slip at room temperature was rationalized upon the basis of grip constraints. A bend-twinning hypothesis was advanced as an explanation of mechanical twinning which occurs as a complex stress-relief mechanism. INVESTIGATIONS of the plastic deformation of magnesium have been limited to the determination of the fundamental kinetics which may be summarized as follows: 1—Twinning on the {102).l 2— Slip on the (001) plane in the [loo] direction at room temperature.' 3—Slip on the {101) or {102) plane in the [loo] direction above 225°C." 4—Critical resolved shear stresses for basal slip in tension at room temperature of 83 g per sq mm with a variation from 57 to 127 g per sq mm." Bakarian' studied the compression of thin wafers of magnesium single crystals and classified the components of the deformation mechanisms as follows: 1—The Basal field: (001) at an angle of less than 20" to the compression surface. Fracture along {101} or slip on (001) followed by {101} fracture. 2—The prism field: (001) at an angle greater than 60" to the compression surface. Twinning on the {102) generally occurring during the early stages of loading, basal slip in the areas of original orientation and (001) slip within twins. 3—The central field: (001) at angles greater than 20" but less than 60" to the compression surface. Slip on the (001). 4—The critical resolved shearing stress for {101} slip above 225°C was 400 g per sq mm. Observations of mechanical twins in hexagonal close-packed metals have been summarized by numerous investigatorsb-' emphasizing a lateral or rotational atomic adjustment, in addition to the pure twinning shear, and the importance of reorienting the basal plane to a position more favorable for continued slip, rather than the resulting small dimensional changes. Criterion for the operative twinning planes has not been clearly established. Schmid and Boas hurmised that an energy condition related to the atom movements is the determining factor. MillerQ bserved that twinning stresses in zinc crystals decreased as the amount of prior deformation increased. Preparation of Specimens Magnesium single crystals % in. in diam x 8 in. long were grown from the melt under an argon atmosphere in a gradient furnace similar to that described by Jillson." Magnesium containing 0.018

Jan 1, 1953

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The current world production of iron oxide pigments is estimated by the author to be between 499 and 590 kt (550,000 and 650,000 st) based on 1979 data. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970) and increasing to $97 million by 1980 (Spinrad, 1980). Nomenclature With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments. Classification An important characteristic of a pigment is its color and, therefore, a logical separation can be made on this basis. A. Yellow Iron Oxide Pigments 1. Natural mineral origin a) Goethite b) Lepidocrocite c) Ochres d) Siennas e) Limonite 2. Synthetic pigments a) Goethite B. Red Iron Oxide Pigments 1. Natural mineral origin a) Hematite b) Siderite (calcined) c) Pyrites (calcined) 2. Synthetic pigments a) Hematite C. Brown Iron Oxide Pigments 1. Natural mineral origin a) Umbers b) Limonite (calcined) c) Siderite (calcined) d) Goethite (bog ore or sulfur mud) 2. Synthetic pigments a) Blends of hematite, goethite, and magnetite

Jan 1, 1983

By J. C. Trantham, J. W. Marx

From 1955 to 1958 the Phillips Petroleum Co. conducted a series of small scale counterflow combustion field tests in a tar sand about 60-ft deep and 6 to 12-ft thick near Bellamy, Mo. A total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern, were employed. Electric heaters, gas burners and wellbore fuel packs were tested as counterflow ignition devices. Direct drive ignition followed by reversal to counterflow operation was not possible in this case because of formation plugging by the semi-solid tar during the direct drive phase. Sustained counterflow burning was achieved with wellbore fuel packs under conirolled conditions which permitted close correlation of fire front velocity, air velocity, air-oil ratios and yields for a wide variation in process parameters. The tar in place was about 10' APl with a reservoir viscosity greater than 500,000 cp. The composite oil prodlcct was 26' API with a viscosity in the range of 5 to 15 cp. Vertical sweep efficiency in the line drive pattern was essentially 100 per cent, with no evidence of gravity segregation. Original tar in place ranged between 800 and 1,000 bbllacre-ft, specific rock permeability averaged about 800 md before burning and effective air pemeability with residual oil and water in place (at the time of ignition) averaged 250 md. The volume of oil recovered during stabilized line drive counterflow burning represented about 67 per cent of the volume of tar originally in place in the burned out zones. A minimum was found when air-oil ratios were plotted against formation air velocities, and a limiting air velocity existed below which the counterflow fire front reversed and burned back over its own trajectory, using the residual coke left behind. INTRODUCTION Early in 1955 the Phillips Petroleum Co. began preparations to field test counterflow underground combustion as a method for producing oil from high viscosity hydrocarbon deposits, such as bituminous (tar) sands. At that time all published information on the use of underground burning io increase oil recovery was based on the direct drive process, in which the fire front moved through the formatim in the same direction as the injected air stream. Such direct burning is not applicable to many heavy oil sands or to most tar sands because the heat-thinned native hydrocarbon congeals in the cold rock ahead of the fire front forming a gas permeability block which smothers the combustion. Laboratory experiments first demonstrated that this permeability blocking would not occur if the fire front and the air stream moved in opposite directions. In this counterflow (reverse) burning process the heated heavy oil or tar is driven back through the combustion zone. Here thermal cracking produces relatively light hydrocarbon products which pass through the heated rock behind the fire front (largely in the vapor phase) and are incapable of causing a gas permeability block.' Exploratory wring revealed that consolidated bituminous sandstones with a combination of tar saturation, permeability, thickness and depth favorable for experimental field testing existed at several points in western Missouri. By the fall of 1955, a test site for determining technical feasibility of the counterflow process under field conditions had been selected near Bellamy, Vernon County, Mo. — about fifty miles north of Joplin. The pay zone was too thin and too shallow to constitute a commercial prospect, but these same factors permitted controlled experimental operation with a small compressor installation and with a large number of monitor wells. These were needed for adequate observation of the underground phenomena at reasonable cost. RESERVOIR CHARACTERISTICS The reservoir chosen for the experimental field tests was a 124 thick section of tar sand extending from 49 to 61 ft subsurface, with shale and siltstone laminations sealing the top and bottom. This section was part of a larger 30-ft thick tar sand deposit which extended both above and below the test zone. Core analyses showed that the 12-ft sand was effectively subdivided into two approximately equal sections, with the lower zone being consistently more permeable than the upper zone. The most significant laboratory core data are summarized in Table 1. The line drive test which is the principal subject of this report utilized only the lower 6-ft thick zone, with the upper zone regarded as part of the 55-ft overburden. WELL PATTERNS The over-all field test program involved a total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern. In some of the tests the full 12-ft zone was employed; in other cases only the more perme-

Jan 1, 1967

By Charles W. Goodale, William A. Akers

The treatment of silver-ores of too low a grade to justify either smelting or preliminary roasting, and yet not " free" enough to permit of raw amalgamation, has ever been a serious problem. As bearing upon it, the operations of the Combination Mining and Milling Company of Black Pine, Deer Lodge county, Montana, during the past year may not be without interest. It is not claimed that the process to be described is not susceptible of great improvement, nor is any claim of originality made for it; but its use is, as yet, not very general, and it seems to offer a means of profitably working the large class of partially-decomposed argentiferous ores which, by reason

Jan 1, 1890

By AIME AIME

THE stage is set for the 1930 Annual Meeting. It will take place in the Engineering Societies Building. Feb. 17, 18, 19 and 20, and an unusual pro- gram of technical papers, symposia, lectures and addresses, interspersed with luncheons, dinners, excursions and worthwhile entertainment for the four days has been arranged. The curtain rises on Monday morning and the first act is by the entire company-registration. Then the meeting hits its stride, for there are ten technical sessions on Monday, and the range of subjects includes most of the Institute membership. The Committee on Coal and Coal Products, which is about to become the Coal Division, presents a symposium of a dozen or more papers on Coal Classification, concluding its afternoon session with several papers on general subjects. At its luncheon between sessions, C. E. Bockus, president of the National Coal Association, will be the honored guest. Papers of theoretical character will be discussed at the morning session of the Committee on Geophysical Prospecting; at its afternoon session there will be presented summaries of results obtained at various properties by methods described at previous meetings of this group and permanently recorded in "Geophysical Prospecting," published by the Institute early in 1929. Members of the Petroleum Division should not overlook the paper by Theodor Zuschlag, on this Committee's program. It is entitled, "Oil Structure Mapping by the Sundberg Method." Members of the Iron and Steel and Institute of Metals divisions will find it profitable to attend the session on Engineering Education on Monday afternoon. E. A. Holbrook has arranged a program of ten-minute talks on Metallurgical Education which are designed to get down to "brass tacks." and the practical man may, in discussion, contribute as well as learn. At 5 p. m. Thomas T. Read will lecture+ at Columbia University, on "Recent Progress in Economics of the Mineral Industries."

Jan 1, 1930

By Stewart R. Wallace

Members of the Society, it is a very great honor for me to be here today and to have the opportunity of telling you about some things that have been accumulating in the back of my mind for some time. Before attempting to do so, I should acknowledge my debt to the many people who are responsible for my presence here this afternoon. To do this properly, however, would consume much of my allotted time and I will therefore mention only two men, both of whom were directly involved in the discovery of the Henderson ore body. The first of these was Robert Henderson, now dead, who at the time the work was going on was vice president of Western Operations of the Climax Molybdenum Co. Truly, he provided the environment that permitted the exploration program to function effectively, and the deposit appropriately bears his name. The second man I meant to mention was resident geologist at Urad at the time of the Henderson discovery. I think I should explain right here that the Urad ore body and the Henderson ore body, although entirely separate, are closely related deposits, and that both are located at Red Mountain in Clear Creek County, Colo.

Jan 6, 1975

No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of "boom" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.

Jan 1, 1925