Search Documents

By Joseph A. Norden, A. R. Willson

Much has been written concerning the hoisting equipment of various mines throughout the country, but most of the literature on the subject, if not all, describes equipment of extraordinary capacity and the small and medium-sized outfits have been neglected. The hoisting equipment here described is capable of handling about 1200 tons per day. It has not been worked to capacity, but 600 to 700 tons, together with men and materials, have been handled in two shifts without any great effort. Only one shaft extends from the surface to the lowest levels of the mine; see Fig. I. It is composed of three compartments, two of which are used for hoisting, and the third for water, air, and electrical lines, and for sinking purposes. In 1909, this shaft was raised from the 1000-ft. (304-m.) level to the 700-ft. There a station was cut and an air hoist installed. At this time all mining operations were confined to the upper levels of the mine; that is, above the 700-ft. The ore was dropped to this level through chutes from the 300-, 400-, 500-, and 600-ft. levels and then lowered in cars on cages to the 1000-ft., which is the main haulage adit, the mill and railroad bins being about 3000 ft. from the shaft. Orebodies were, in due time, developed on the 1000-ft. level and below. Therefore, in 1913,the shaft was sunk to the 1150-ft. level and thereafter sinking was continued at regular intervals until the 1500-ft. level was reached. But, hoisting from the 1300-ft. level was a difficult and slow process with the antiquated air hoist, so, in 1916, it was decided to raise the shaft to the surface and install a modern, electrically operated hoist. This was completed early in 1917 and the hoist was in operation in March of that year. The Hoist Figs. 2, 3, and 4 show various features of the hoist and electrical equipment. A Nordberg engine of the double-drum, geared type, designed for a 10-ton load, including rope, at a speed of 1500 ft. per min., is used. The drums are 7 ft. (2.1 m.) in diameter, with a 54-in. (137-em.)

Jan 1, 1922

By S. Razi

Injection luminescence of single crystals of rare-earth-activated CdS was investigated. Crystals of CdS:Nd, CdS:Er, and CdS:Yb, grown by the vapor transport technique, were suitably etched and hetero-junctions of Cu2S-CdS were fabricated on one side of the CdS substrate by chemical reaction. The device was then heated to 200°C in an inert atmosphere for 5 min. Static V-I measurements show that at low voltages (V < 1 v) the current is controlled by the junction, while at higher voltages the bulk Properties of the CdS substrate effectively control the current. Because of the large thicknesses no negative resistance was found. Reverse breakdown voltage varied from 5 v, for junctions that were not heat-treated, to 100 v, for diodes that received the proper heat treatment. The rectification ratio, measured in the range of 2 to 10 v, varied from 300 to 3000. Capacitance- voltage measurements indicate a weak dependence of the junction capacity on applied voltage. The capacity was found to increase appreciably with room light illumination. The variation of capacitance with frequency is indicative of a p+-i-n structure. An open-circuit voltage of 0.4 v was measured under an illumination of 100 mw per sq cm. Under forward bias, the bluish-green edge emission characteristic of CdS was observed. No sharp rare earth emission line was observed, which is in contrast to our results using ZnS:Tb, where, under high-voltage excitation, the rare earth emission was dominat over the lattice emission. The absence of rare earth emission implies that either the nature of the rare earth ion is different at the het-erojunction than in the bulk or the probability of energy transfer to the rare earth ion is small. RARE earth elements are playing an increasingly important role in the Synthesis of materials for a variety of purposes, e.g., solid-state lasers, color television screens, and so forth. Interesting systems result when wide-band-gap photoconducting lattices are activated with rare earths. A study of the lumines-

Jan 1, 1969

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main Tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials, it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted. A tight partition of 2-in. (5.08-cm.) plank was erected between the auxiliary and the adjoining hoisting compartments, for better protection of men riding on the cages. The application of concrete made this

Jan 1, 1920

By S. A. Hoenig

In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in [Fig.1]. Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in [Fig. 1]. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 /MI (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 µm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform.

Jan 1, 1985

By J. R. Eckel

It has long been known that mud properties affect drilling rate and that drilling with water is as much as six to .seven times faster than with mud. However, it is not known why drilling rates with mud are lower. Recent studies show what fluid properties govern microbit drilling rate and also provide a quantitative correlation of these fluid properties and hydraulics with microbit drilling rate. All the microbit tests reported in this paper were made with a low permeability (about 10 md) limestone. They were conducted at constant bit weight and rotary speed with varying fluid properties, flow rate Q and nozzle dinnteter d. The tests showed that (1) drilling rate in a given system with constant circulating rate and nozzle velocity is a function of the kinematic viscosity [viscosity /density, (cp)/ p (density)] of the drilling fluid measured at near bit nozzle shear rates; (2) the combined effect of fluid properties and hydraulics on microbit drilling rate is defined by a Reynolds number function (kQp/dp); (3) for the same kinematic viscosity, drilling rate is independent of solids content; and (4) for the same kinematic viscosity, drilling rate is independent of fluid loss. INTRODUCTION The fact that mudding up reduces rate of penetration is well known, but the reduction varies from well to well. The rate with mud may be 80 percent of the water rate or it may be as low as 15 percent. Since this reduction of up to seven-fold takes place under conditions of constant bit weight, rotary speed and mud circulating rate in a uniform formation, it can only be a result of the change in fluid properties. Previous work1-" both in field tests and in laboratory microbit tests) showed that drilling rate with mud is lower than with water (Figs. 1 and 2). Microbit tests also confirm, at least qualitatively, the field observation that drilling rate slows with increased pressure differential from borehole to formation (Fig. 3). The qualitative effect of drilling rate of bit weight, rotary speed and rate of mud circulation are also the same for the field and microbit rig. For these reasons, the industry generally accepts microbit results as being qualitatively meaningful in terms of field application.

Curiously enough, considering the relative accessibility of the two places, coal was reported at an earlier date in Saskatchewan than in British Columbia. Henry and Thompson were on the Saskatchewan River in February 1811, and on the 4th of that month recorded, while on Jack&apos;s Branch of North Brook, "I observed in one of the bends on the north side a bank of yellow clay, on which there appeared several horizontal veins of pure coal, of the best quality I have seen along this river." Later at Rocky Mountain House it was said: "a quantity of coal is tumbling into the water, as the current washes away the earth underneath. This coal abounds along the Saskatchewan, in some places forming solid beds several feet thick for several acres, which are washed by the river. In its pure state our smiths use it for the forge with equal proportions of charcoal made of birch or aspen, which answers every purpose for making and repairing our axles and other tools."1 It is needless to say that it was many years before this coal was used for any commercial purposes. Coal was first found on the northern end of Vancouver Island in British Columbia in 1835 at Beaver Harbor, where later Fort Rupert was established, where Indians had advised some of the Hudson Bay Company officials it would be found.2 The coal was used by smiths, and later on by the steamer plying along the coast.3 A report to the government in 1845 called attention to the coal reported in the neighborhood of Puget Sound and on the Cowlitz River, and that probably the samples used by the Hudson&apos;s Bay Company were obtained from the surface and. were not good. On September 7, 1846 a report on the coal situation was submitted by Ogden and Douglas, and a naval vessel was sent to investigate the report and was loaded with 62 tons dug out by the Indians, the seam outcropping along the shore.2 In 1847 some samples were sent to England by a returning war vessel. In 1849 the Hudson&apos;s Bay Company established a

Jan 1, 1942

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond&apos;s original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond&apos;s original, suggests that Thoreau&apos;s advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By Charles Baker

THE district of Catorce, San Luis Potosi, ranks among the first half-dozen silver-producing camps f Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapum, Mazapil, Palomas, Musquiz, Minas Virjas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (609.6 m.) in 4 1/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catorce from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catorce, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to erosive forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstones, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains; some f this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution f the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebbles, and finer detritus.

Jan 9, 1921

By Thomas Cox

THIS paper makes no claim to any new idea; it simply reviews the Treasury Department Regulations pertaining to the practical application of depreciation and depletion and other allowances governing taxation of oil and gas properties. Other methods may be existent, but as they may not conform to the legal status they must be discarded. In complying with the present laws governing the, industry with regard to taxation and the allowable deductions therefrom, the following considerations are essential: Depletion, depreciation, amortization, other allowances, and items not deductible. It is definitely understood that depletion is the loss or exhaustion sustained in the continuous operating of an oil and gas property, and that each unit of oil or gas taken out reduces the value of the property until its final exhaustion. Depletion applies only to the natural deposits of oil and gas due to their-removal in the course of exploitation of any property. Depreciation is defined to cover the waste of assets due to exhaustion, wear and tear, and obsolescence of the physical property, and is separate and distinct from depletion; its allowance is that amount which should be set aside for the taxable year in such sums as for the useful life of ,the property will suffice to repay its original cost-or its value as of Mar: 1, 1913, if acquired by the taxpayer before that date-less the salvage value at the end of such useful life. Amortization is allowed for such facilities as were built or acquired on or after Apr. 6, 1917, for the production of articles contributing to the prosecution of the war and, in the case of vessels, those built and acquired after that date. The amount to be extinguished, in general, is the excess of the unextinguished or unrecovered cost of the property over its maximum value under stable .post-war conditions.

Jan 9, 1920

By S. Parker Gay

In 1967 Southern. Peru Copper Corp. was faced with the problem of developing a water supply for their new Cuajone open-pit copper mining and milling operation, at a time when the existing water system was inadequate for a proposed expansion of the producing Toquepala mine. The most probable source for additional water was considered to be the Pasto Grande basin lying 30 km north of the terminus of the pipeline. This source of supply could be developed only at substantial cost, after construction of a dam, tunnels, pumping plants, and several miles of canals. Investigation of other possible sources was undertaken, and one of these was the Huaitire alluvial fan which had been recognized on aerial photographs in 1961. Resistivity soundings on the fan provided isopach information for estimating the volume of fan sediments. In the course of carrying out these soundings, a high-resistivity layer at depth was indicated. The favored geological interpretation of this layer at the time was a tight impermeable volcanic formation, but an alternative explanation was a ground-water aquifer of high transmissibility. Geological studies just released by the Peruvian Geological Map Commission supported the latter interpretation. A diamond drill hole sunk to a depth of 725 ft on the Huaitire Pampa in June 1967 proved the absence of the expected volcanics, the presence of the sediments, and indicated that some sedimentary horizons carried artesian water. Subsequent well drilling and hydrological and geological studies show that the aquifer occurs principally in the Upper Tertiary Capillune formation, covers an extensive area on the Peruvian altiplano, discharges enormous quantities of water to a large number of canyons dissecting it, and will adequately supply most, if not all, water needs of the Cuajone operations.

Jan 1, 1973

By Arthur West

IT is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic. plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 tons capacity each. In this, as in all the other stations described in this paper, each furnace is blown by-two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years&apos; experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines.

Jan 6, 1915

By W. M. Weigel

THE rapid advance, during recent years, in the manufacture of articles that have been in common use for generations and the development of new materials entering into appliances and devices unheard of fifty years ago, have created a demand for some of the more common non-metallic minerals. To supply this demand there has quietly developed a branch of the mining industry of which little is known by most mining engineers the mineral-filler industry. In this paper, and generally in the trade, the term mineral filler is applied to a mineral used, in its natural state after mechanical preparation only (such as. grinding, milling and washing), without undergoing any chemical change and without exerting any chemical action on the substance with which it is incorporated. The consumption of mineral fillers is confined chiefly to large manufacturing centers in the eastern and northern states. Where available, materials originating near the place of consumption are used, as most fillers bring a comparatively low price and, frequently, the freight may equal the cost of the finished filler at the mine. The southern states have abundant deposits of non-metallic minerals suitable for fillers, which supply the manufacturing industries in adjacent states. Many of these deposits are equal to, or superior, in quality to those mined in the north, but they can not compete with them because of the freight rates. The mineral-filler industry has felt the present depression, but it has suffered less than most mining industries for as a rule the mills are simple, the overhead expenses are low, and the labor is entirely local and can revert to farm work when the plant closes down. Many other deposits in the southern district will undoubtedly be developed when business. revives and freight rates are adjusted.

Jan 2, 1922

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940

By W. H. Adams

Virginia, a store-house of metals, is more and more a surprise to the present generation. With her enormous available mineral wealth, worked upon steadily for over a century, exploited SUEciently to demonstrate beyond question costs and values, reported upon by our most eminent scientists, written up by thoroughly earnest correspondents, we yet find her little understood by capitalists or practical men, and until very lately overlooked by the advanceguard of pioneers in metallurgy, whose restless energy conquered the wilderness of Northern Michigan years ago, and has written a new and startling history for almost impenetrable Western territories. The world is learning through the mouths of giant furnaces lately put in blast at Lowmoor, Goshen, and Roanoke, more of this wondcrful State. It is becoming plain that nearer home, amid all the surroundings of civilization, under an equable climate and with the advantage of a minimum cost for fuel and labor, there are stores of mineral, varied in character and deposited over a wide area, which exceed all ordinary calcnlations. Principal among these minerals, iron ores have been, and will probably continue to be, the leading product and the source of greatest revenue. My attention has been called during the past year to one particular section of the iron-belt, where for forty years charcoal-furnaces were successfully operated, the ores being mined in open pits, as can so frequently be seen from the Connecticut line southward into Georgia. There is, however, a significant peculiarity in the character of these deposits of Louisa county warranting special mention, as it is thought that nowhere on the earth&apos;s surface, within so moderate a distance of tidewater, can their like be fouad. Probably half a million tons of lump and wash-material have been taken from pits

Jan 1, 1884

By Albert Williams

A large proportion of the work performed in wet-crushing silver mills is devoted to the handling and re-handling of pulp between the battery and the pans. There seems to be no generally applicable substitute for the settling-tanks, and in the present system of constructing mills the tanks involve an amount of labor which may be regarded as disproportionate and unnecessary, in view of the automatic improvements which have been introduced in other directions. This diffculty has been met, however, by Boss&apos;s continuous process, in which the pulp flows directly from the mortars to the first of a series of constantly working overflow-pans. This method has been adopted at the Noonday mill, Bodie, California; the Harshaw, Arizona; the Sierra Grande, New Mexico ; and the Prietas, Sonora. The continuous process, while giving excellent results with special ores, and under peculiar local conditions (such as a deficiency in water supply), is not, I believe, claimed to be available for all raw-amalgamating mills, notwithstanding its well-merited popularity for certain work. Some trouble has been experienced from the tendency to concentration in the pans, though this can be avoided by skilful manipulation. It has also the disadvantage inherent in combinations of distinct operations ; it requires a very nice adjustment of the water supply to obtain full battery efficiency without running the pans too thin, though the latter defect is partially compensated for by the gradual thickening of the pulp as it proceeds through the series of pans. The objection is similar to that which holds in a parallel duplex process, that of combining roasting and smelting in a single furnace, where each operation is injuriously affected by the necessity of fitting it in with another and entirely different one.

Jan 1, 1883

By W. S. Ayres

BACK in the early nineties the old Dickerson iron mine in Morris county, N. J., was operated by a vertical shaft 850 ft. deep and by a continuing slope for more than 1000 ft. more 011 an incline of 65", together making the vertical depth about 1800 ft. I was then the general superintendent there. This mine, named for a former governor of New Jersey, had been worked more or less continuously from long before the American Revolution and up to this particular time. The pumping equipment was of the old-time Cornish type, with its long pump-rods running down the vertical shaft and the slope to the sump at its bottom. It was operated by a large flywheel engine in the engine room and all angles were turned by the usual bobs. Saturday was the day fixed for lowering the "suction" into the deepened sump at the bottom of the advancing slope. The mine foreman had gone down with the morning shift to superintend this very vital and particular work, which consisted not only of lowering the "suction" into the sump immediately after the pump had been stopped, but of securing it to the rock and putting in the added sections of column-pipe and of tightening up the numerous bolts at their joints, all before the water rose to the point of working. At an appointed time during the forenoon I had agreed to go down into the mine and join the mine foreman in consultation over any difficulties that might have arisen. At the time agreed I went down by the cage to the bottom of the vertical 850-ft. shaft, and then by ladders down the slope for over 1000 ft. more.

Jan 1, 1930

THE TRANSACTIONS of the Institute for the early years display but Little interest in physical metallurgy-indeed, it is striking how thoroughly process metallurgy absorbed attention until quite recent years. The first volume carries no article that can be strictly described as physical metallurgy, unless one on the rolling and hammering of ingots be doubtfully so described. Nor does the second volume contribute more the interest then was in mining, and in production methods, both ferrous and nonferrous, with much attention to the new methods of making steel. The third volume records papers on: the condition of carbon in gray and white iron, a paper devoted to chemical rather than microscopic analysis; the annealing of spiegeleisen; phosphorus and carbon in iron and steel, similarly chemical. Much attention was given, and continued to be given for years, to the manufacture and behavior of rails. The question of the nature of steel appeared early (Vol. 11)-What is Steel, by A. L. Holley-where arguments on nomenclature were already active; and Holley also bemoans, in modern spirit, the Inadequate Union of Engineering Science and Art; Pearse wrote on cast iron for guns (reflecting again the ironic beneficence of war in metallurgy), and said that Captain Walbach was the first to insist on chemical analysis of gun irons; he quotes Major Wade&apos;s study of comparative hardness, using penetration hardness measurements (Brinell was to come later), and quotes the important Reports on the Strength and Other Properties of Metals for Cannon, by H. C. Baird, Philadelphia, 1855, in which the advanced state of tensile testing at the time is shown. Hewitt, in Vol V, comments upon the function played by technical schools and technical societies upon the growth of metal-

Jan 1, 1948

To the members of the A. I. M. E., who have given much and risked all to fight "Over There" with pick, or gun, or brain, and to the members who have chosen the sometimes more self-denying duty of remaining at home to help produce metals for fighters: Your experience in foreign lands has bred in you that spirit of internationalism which will soon be infused into every corner of our country by virile lads thrilling from a great experience in an old, yet new, land over the seas. To them the East will not seem as far from the West as it was, nor the North from the South. Sectional jealousies will seen despicable to one who has fought for a great ideal shoulder to shoulder with real men of other nations. And they who have willingly sacrificed much on the altar of service will have little patience with an egotist, be he laborer, tradesman, capitalist or engineer. The problems which peace brings to us are more difficult than those of war and their solution requires not only cool heads, tolerance, and wise judgment, but the "getting together" of sections and classes and individuals. The triumph of justice over individualism, represented by the draft law, must be repeated, for there are "slackers" in peace Is well as in war, and the spirit of self-denial expressed in response to Liberty Loans, Red Cross, and Welfare drives and Food Administration appeals must live. We have only just begun to learn how to serve. It is often claimed by our members that the engineer is not given, in the community at large, the recognition which his training should merit; that his reward is not as great nor his service as welcome as it should be. Public service is generally assumed to be a logical activity for a lawyer,

Jan 12, 1918

By C. P. Parsons

Caliper logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork. Introduction Caliper logging of the open hole in oil wells, recently introduced and now showing initial results in many sections of the country, is providing information that is filling a long-felt need in oil-well cementing and in numerous other oil-field practices. Briefly, it measures the variations in diameter, of the open hole in a well. This direct physical measurement of the strati-graphic profile has considerable value for subsurface interpretations by the geologist, engineer, driller and others charged with the responsibility of properly completing and repairing oil and gas wells. The caliper shown in Fig. I is run into a well in closed position. The four arms are released when logging is to start. These arms are independent of each other. As the calipers are pulled upward through the open hole, the arms are like nimble fingers feeling the changing profile of the hole. This mechanical action is in turn converted into an electrical circuit, which is connected to a recording mechanism at the surface. a. Lowered into well in closed position. b. Arms released. Readings are made while caliper travels upward. Direct recording is made at surface, in inches. The recording of the diameter of the hole is directly in inches.

Jan 1, 1943