Search Documents

"Rock falls involving a relatively small amount of material are a leading cause ofinjuries in underground mines in the United States. A contributing factor is unwantedblast damage and over-break. A goal of the United States National Institute forOccupational Safety and Health is to reduce the number of ground fall-related accidents by improving drift driving practices through the introduction of perimeter control blast designs. This paper presents a blast design technique based on a hydrodynamic method. Using commonly available explosive and geometry data, the theoretical particle velocity is calculated as a function of distance away from a cylindrical charge. A calibration factor is introduced to account for actual conditions by comparing the predicted values to a set of field data. The calibrated curve can then be applied for design. The paper introduces modifications to account for different explosives from those used in a calibration test. The application of the approach is demonstrated with respect to a data set from a large-scale concrete block test."

Jan 1, 2009

By Shaw-Shong Liew

This paper presents the processes of investigation, analysis, design, construction and monitoring of soil nail stabilisation work to facilitate a 14.5 m deep excavation at an uncontrolled fill ground. An extensive instrumentation programme had been implemented to monitor the performance of the stabilisation solution, to provide validation for the designed nail resistance and groundwater variation. From the monitoring results, it was proved that the soil nail stabilisation technique is effective for loose saturated fill provided that substantial care is taken during implementation. Construction difficulties, solutions to overcome the problems and lessons learned will be discussed in the paper.

Jan 1, 2006

By Samuel J. Kosa

The Monotube is a uniformly tapered high-strength steel shell pile manufactured for friction pile applications. The Monotube pile was developed in the early 1920's in Canton, Ohio. Its first commercial installation was an Ohio railroad trestle in 1926. The Monotube has been manufactured in the same Canton plant since its inception. The Monotube is produced in four diameters, 12, 14, 16 and 18 inches, with U. S. Standard Gage wall thicknesses of 9, 7, 5 and 3. The uniformly tapered Monotube section can be manufactured in one of three rates of taper.

Jan 1, 1993

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48? to 72? open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2013

By W. R. Reed

The National Institute for Occupational Safety and Health (NIOSH) uses light-scattering dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer, was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By Mark P. Meyer

During 1991 through 1993, the U.S. Bureau of Mines (Bureau) -Alaska Field Operations Center (AFOC) in cooperation with the Bureau of Land Management (BLM) -Arctic District Office and the State of Alaska, Division of Geological and Geophysical Surveys (ADGGS), conducted exploration, geological, geochemical, geophysical, mineral resource, and mineral potential investigations in the 6.7 million hectare Colville Mining District (CMD) study area. This mining district study area, located in northern Alaska, includes the Colville River drainage basin as well as 0.35 million hectares of the southern part of the National Petroleum Reserve in Alaska (NPRA). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district program. The Bureau's MLA mining district program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies.

Jan 1, 2011

By Ergin Arioglu, Werner Burger

"SUMMARY The Istanbul Strait Road Crossing Project includes a 3.34 kilometer subsea tunnel excavated by TBM with an excavation diameter of 13.71 m. The tunnel will incorporate two road decks, each employing two traffic lines and shoulder with the daily capacity of 100,000 light vehicles. The tunnel alignment crosses full face rock sections with heavily fractured zones due to tectonic events as well as a long central stretch of difficult mixed face and very variable soft ground conditions. The demanding ground conditions and the large diameter in combination with realized face pressures well above 10 bar required a highly specialized and well adapted TBM. The paper describes the project challenges and the related technical solutions incorporated within the TBM design as well as the real site experience. INTRODUCTION In 2013, a 13.71 m diameter Mixshield was manufactured in Germany for the Istanbul Strait Road Crossing Project. The delivery of the TBM in late 2013 was a major milestone for the Istanbul Strait Road Crossing Project, also known as the Eurasia Tunnel Project. The Eurasia Project (www.avrasyatuneli.com.tr/en) consists of a 14.6 km route including a 5.4 km tunnel segment in its central part crossing the Bosphorus. The 3.34 km subsea section of the tunnel was excavated in closed mode using a Mixshield TBM. The remaining tunnel length is constructed by sprayed concrete lining (SCL) method followed by a cast in place (CIP) lining or by cut and cover (CC) structures for the TBM transition boxes (Figure 1, right). Other project sections on the European and Asian side consist of upgrading and widening surface access roads towards the tunnel. Conceptual ideas of connecting Asia with Europe via a tunnel crossing the Bosphorus have been around for an extended time and only became realistic towards the end of the 20th century based on significant technical developments in mechanized tunneling. Feasibility studies for a new Bosphorus crossing in 2003 and 2005 confirmed and suggested a road tunnel in its present alignment as the preferred solution. Following an international tender process the Ministry of Transport, Maritime Affairs and Communications of Turkey assigned ATAS, a special purpose company formed by Yapi Merkezi (Turkey) and SK E&C (South Korea), to design, build and operate the Eurasia Tunnel Project. The Implementation Contract was signed in February 2011. In 2012, Herrenknecht AG was selected as the supplier for the 13.71 m Mixshield TBM."

Jan 1, 2016

By David G. Borg, John Bussey

The new AIRDEK (tm) technique for pre-splitting in surface coal mines produces highwall conditions that have greater safety with lower costs for explosives, labor, and drilling. Successful applications have been made in highwalls ranging from 20 to 100 feet or more and in blasthole diameters from 3-1/2 inches to 12 inches.

Jan 1, 1988

By Marcos Villegas

El presente texto describe el desarrollo del sistema de gestión de riesgos en la reingeniería de procesos, justificando la inversión en gestión de riesgos de la concentradora Atacocha donde se protege a las personas, activos e ingresos, minimizando el potencial de pérdida de los riesgos y así proveer fondos para recuperar las posibles perdidas y soportar el sistema en salud, seguridad, medio ambiente y Calidad (SSMAC).

Sep 9, 2007

By Tyler R. J

Methylene blue dye adsorbs on chalcopyrite concentrates slurried in aqueous solution. Saturation adsorption can be achieved within about 24 hours for dye equilibrium concentrations greater than about 10-5 M. The dsorption coverage is obtained from a measurement of the' colour change of the solution. Comparison with BET measurement of the concentrate surface area shows that 2.4 ± 0.1 µmol of methylene blue are adsorbed per square metre of surface accessible to the dye cation. The procedure described can be used as a single-point measurement and values for the surface area can be otained to within about 10 per cent with inexpensive instrumentation.

Jan 1, 1979

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

The projection of operating costs for mining, processing, and other site operating costs is an exercise which can be fraught with considerable peril. Not only are the physical characteristics of each mineral property unique, but a range of other factors will influence the consultant's approach to compiling cash flow estimates. This paper details some of the techniques used in estimating operating costs for use in order-of-magnitude cost studies and feasibility studies, and describes how to avoid common areas of difficulty. A series of examples relating to open pit gold mining and processing cost estimates illustrate these problems, and various corrective methods are described. The mining and treatment processes, and their associated cost elements, are followed in sequence of operation from on-going ore delineation through to disposal of the product. In addition the problem of assigning management, administration and overhead costs along with taxation allowances is addressed. Of critical importance is the application or possible misapplication of accrual procedures to the cost elements. In many cases such misapplication can introduce more pronounced errors with projects of short duration, such as the typical open pit/C.I.P. gold operation commenced in the last decade. The importance of providing verification of estimates depending upon the standard of the cost study is also investigated, and opinion is provided upon the minimum levels of verification necessary at various stages. Finally, the amalgamation of the various individual cost elements into a coherent whole is reviewed.

Jan 1, 1990

By N. S. Kim

Economically favored Cr and Cu leaching out process from spent power plant fly ash (PPFA) had been investigated. PPFA, bearing of C, S, V, Ni, Cu and Cr, has been widely used as an assistant fuel in cement industry. Recent environmental regulation in S. Korea prohibits using PPFA as a fuel. Many researchers have also studied on extraction V and Ni from PPFA. Due to low concentration of V and Ni, 2% and 1%, respectively, economical and environmental friendly process could not be found. In this study, Cu and Cr have been removed in an economical way and which satisfied with KS Extraction Test. The rest unburned carbon, V2O5 and NiO2 in residue were found to be applicable for indoor and outdoor colored bricks or deodorant panel. Various parameters such as pH, lixiviates and time on leaching behavior were investigated in order to leach Cr and Cu remaining C, V and Ni. Keywords: Fly ash; Selective extraction; Ammonia; Deodorant panel

Jan 1, 2009

By Lyn Jones, Mike Bratty, Rick Lawrence, David Kratochvil

"The treatment of water is required at many mining operations to remove metals and prevent the discharge of contaminated water to the environment. In other cases, water treatment is used to provide better quality water for recycle to the processing plant, or to process bleed streams in hydrometallurgical operations in order to prevent deterioration in metallurgical performance or process equipment. BioteQ Environmental Technologies Inc. has developed and commercialized the BioSulphide® Process which can provide an alternative for these treatment needs and which can also be used for profitable metal recovery, particularly in cases where conventional metal winning techniques are not economical. The BioSulphide® Process is a high rate anaerobic biotechnology for on-site production of H2S from sulphur species, although for smaller flows and metal loadings, the use of chemical sulphide reagent might be more cost effective. Both new projects and existing commercial operations, used for removal and/or recovery of copper, nickel, and zinc, and which range in sulphide generating capacity from 50 kg/day to 3.7 tonnes/day, are discussed. Particular focus is placed on the results of operations at the Raglan Mine in Northern Quebec where dissolved nickel is removed from contaminated water at a high efficiency through the precipitation of nickel sulphide. Plant effluent is discharged directly to the receiving environment and the high-grade nickel sulphide product is combined with the nickel flotation concentrate produced at the mine. The plant at Raglan will replace the existing conventional water treatment plant and will eliminate the need for on-site storage of treatment plant sludge.INTRODUCTIONThe BioSulphide® Process, which produces low cost H2S for use in selective metal precipitation, offers a low capital cost alternative which can operate efficiently and cost-effectively within a wide range of flows and solution grades. Since the technology can be used to recover metals from solutions with low flows and metal grades, the technology is also applicable to environmental applications for water treatment, with the sale of recovered metals providing an offset to treatment costs. For environmental control, the technology has a distinct advantage in being able to meet strict effluent discharge criteria due to the very low solubility of metal sulphides. To date, BioteQ Environmental Technologies has designed and constructed three plants for metal sulphide precipitation, with another three projects in the advanced development stage."

Jan 1, 2006

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By C. Sima, M. Legoabe

Keywords: Pyrometallurgy, furnace, platinum Mortimer Smelter is one of the three smelting operations in the Anglo Platinum Group. It is located in the Limpopo Province, approximately 100 km north of Rustenburg, and approximately 15 km west of Northam. The smelter operation is the smallest of the three smelting operations in the group, with a smelting capacity of 170 kt/annum. The operation consists of a Larox filtration plant, a Drytech flash drying plant, a modified Elkem / Hatch 19.5 MVA furnace, and a 60 t/h matte crushing plant. The operation does not convert its furnace matte, and hence the final sulphide rich matte is transported to and processed further at the Anglo Platinum Converting Process (ACP) within the Waterval Smelter Complex in Rustenburg. Furnace slag is granulated, and processed through a slag mill, or transported to a slag dump.

Jan 1, 2006

By W. F. Dietrich

1. On St. Thomas and St. Croix, and possibly also on St. John, low-quality red-burning clays probably can be developed to provide the major part of the raw materials for structural clay products and earthenware pottery. 2. The potential sales volume for structural clay products is too small to sustain a plant in the Virgin Islands to manufacture such products in competition with Puerto Rico; however, handmade patio tile might be produced successfully. 3. The market for pottery utility wares in the Virgin Islands is too small to justify a plant devoted solely to the production of such wares; but it may be feasible to evolve a diversified community activity to make jugs, pots, casseroles, bowls, charcoal burners, patio tile, and other items.

Jan 1, 1955

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011

By Rogerio Castejón

The evolution on the computer in the last 10 years have caused a big change on the way the mining companies are doing exploration. The following factors have contributed to that change: the downgrade of computers and software cost associated with the “usability” (easy of use) of the present systems (remember the old DOS and UNIX systems). New systems are more focused on the users rather than on the experts in applications, meaning that the geologist must understand geology and not operational system, programming, etc. Market conditions requires exploration to be faster and more intelligent than in the “old” times, and companies are always demanding quicker answers from their geologist group as well as lower exploration budgets. Exploration teams must be more effective and efficient. In this sense, the only way to achieve those requirements is to use the proper techniques, methods and tools on the diverse stages of exploration. Its necessary to consider that the costs of data acquisition increase, almost exponentially, through the stages of exploration, from grass roots to advanced stage.

Aug 25, 2002

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973