Search Documents

By O Kirtel, A A. Faizan

With the rapid increase and development of high-speed trains (HSTs), the problems such as train-induced ground vibration and its dynamic effects on nearby structures have become a major environmental concern in urban areas. Ground-born vibrations produced by high-speed trains pose a great challenge for engineers to build structures in such areas that is applicable for residents. In order to study the effect of train-induced ground vibration on nearby buildings, an advanced three-dimensional finite element model for train-induced ground vibrations has been developed using PLAXIS 3D Ultimate. The results of the in situ measurements which was previously carried out by the authors were used to validate the numerical model. The field test for ground vibration due to the passage of a high-speed train was carried out on the Istanbul-Ankara high-speed railway in Turkey with a train speed of 250 km/h. An in-depth analysis was achieved to investigate the effect of different soil properties on the train-induced ground vibrations by using the verified model. According to the result of the vibration analysis, the relative vibration response curves in all directions (x, y, z) for different soil conditions were obtained comparatively. The obtained results of the vibration analysis are discussed in order to figure out some useful conclusions.

Nov 29, 2022

By M Revell, B Sainsbury, D Sainsbury

This paper extends the existing knowledge associated with the design and placement of prefabricated pastefill barricades through a consideration of asymmetric drive geometry and conditions. The load capacity of prefabricated barricades and their failure modes are considered in relation to abutment geology and barricade geometry that includes curvature and span and drive geometry that includes abutment angles, haunch angles and misalignment. Design charts are provided for typical barricade sizes to provide general guidance for design capacities and optimising location placement based on asymmetric drive geometry. A recent barricade failure is considered in relation to the drive geometry and the potential impact it had on the installed capacity.

Nov 29, 2022

By G W. Swana

Elastoplastic parameter is a parameter that describe how much materials behave elastically up to certain stress states and plastically thereafter (Hudson and Harrison, 1997). In the continuum analysis, two main parameters of the elastoplastic parameter are modulus elasticity and Poisson’s ratio. In the slope, elastoplastic parameter holds the main role for stability related to deformation in ductile type of rock. There’s a limitation to determine elastic or plastic deformation at the field for ductile rock type. Field manifestation commonly showed that there was no accumulation zone during and after the sliding failure mechanism, in other hand, at the research area, manifestation of deformation at the toe of slope only indicated by bulging shape. This paper will focus at the sliding failure occurred at Coal mining Pit Y owned by Arutmin Indonesia, which according to failure investigation report similar with the condition described above. This paper also will be based on two hypotheses, first hypothesis is claystone rock mass has not been reached plastic deformation yet and the second hypothesis is there is a chance that elastoplastic parameter of the rock mass has been changed during the deformation/sliding failure process. Research method of this paper are back analysis using probabilistic analysis in Finite Element Method (FEM), which conducted before and after failure. Then, the result of the displacement or deformation of the analysis will be checked with the actual deformation shape. Meanwhile, the change of the elastoplastic parameter will be analysed and interpreted. This paper hopefully able to be developed to study about elastoplastic behaviour of rock mass in actual condition and the influence of another uncertainty factor which determine the slope stability.

Nov 29, 2022

By J J. Van Wijk, A R. Penney

Successful management of geotechnical risk at a mining operation is more than just having a good ground control management plan or using advanced numerical modelling and the latest monitoring technologies. The fundamental requirements for effective geotechnical risk management include identification of potential failure modes, identifying and implementing appropriate controls, and demonstrating the effectiveness of those controls. Effective geotechnical risk management requires an integrated approach by confirming that appropriate risk management systems have been identified and implemented (management plans, procedures etc), and that these systems are executed consistently in the field across all working areas. Development of a thorough integrated auditing process executed by an experienced team of technical subject matter experts with substantial operational knowledge, provides a more complete picture of catastrophic hazard management. Following consistent evaluation criteria allows benchmarking of systems and implementation compliance between the sites being audited, and the results can then be ranked against other operations in an industry database.

Nov 29, 2022

By A Taheri, G D. Nguyen, M Karakus, S Akdag

During underground mining operations, rock masses are highly subjected to dynamic disturbance caused by blasting, mechanical drilling and earthquakes resulting in strain burst, slabbing and spalling. The dynamic fracture is a significant manifestation of rock failure in deep underground engineering, and it is of great importance to assess the dynamic fracture behaviour of the rock mass under elevated temperature conditions. The correlation between temperature – and loading rate-dependent dynamic fracture mechanism of strain burst is yet to be established. A good understanding of the dynamic fracture behaviour of brittle rock subjected to high-temperature under dynamic loading is required for the prediction of the damage extent during strain burst, and proper design as well as control of the underground rock structures. In this study, dynamic mode I fracture toughness tests are carried out on cracked chevron notched semicircular (CCNSCB) granite specimens to reveal the dynamic fracture characteristics of the brittle rock. For this purpose, a Split Hopkinson Pressure Bar (SHPB) apparatus is utilised to conduct the dynamic tests with various striker velocities on thermally degraded granite. The dynamic mechanical behaviour of granite after high-temperature treatment is examined and discussed. The dynamic fracture toughness is determined and compared for the specimens exposed to different temperatures at various dynamic impacts. The fracturing processes are recorded by a high-speed camera (HSC), and the crack propagation speeds are estimated by HSC image analysis. In addition, the dynamic fracture process and the coupled effects of temperature and loading rate on the dynamic fracture modes are identified by HSC image analysis. Energy partition characteristics in dynamic fracture of granite are quantitatively investigated.

Nov 29, 2022

By T Wang, D Wang

Photogrammetry-based techniques supported by traditional mapping tools are more frequently used for open pit geotechnical mapping. It fundamentally involves the collection of geological, structural and rock mass data from pit batters when safe to do so. These are essential components for refining and implementing continuous improvements to geotechnical models. The geotechnical model is used to review bench performance, optimise geotechnical design parameters, interpretation and analysis of pit slope stability. This paper is a case study of implementing different pit mapping methods at Mount Carlton gold mine, North Queensland. It critically reviews the tools required, including the Brunton compass, mobile application Clino, geotechnical data mapping software CloudCompare (2015) and Sirovision software. The review compares the image precision, structural measurements and data analysis. The review also underlines mine site management philosophy for safe geotechnical data collection to identify in-pit geotechnical hazards and the mitigation of potential slope instability. Sirovision is a remote sensing system for site geology mapping and interpreting geotechnical characteristics of exposed mining faces. The system utilises off-the-shelf digital SLR cameras to capture stereo photographs of the rock face and uses the latest image processing technology to generate accurate 3D models. These 3D models are digitally analysed using computational geometry to extract unbiased and accurate geological and geotechnical data. CloudCompare processes high accuracy 3D dense cloud rock surfaces reconstructed with photogrammetry software to extract the geological planes using the FACET or Compass plugins. The major discontinuity sets can be observed and the orientation (dip/dip direction) obtained from the algorithm is accurate and reliable for geotechnical assessment, including kinematic and rock slope stability analysis.

Nov 29, 2022

By E Shilov, R Dixon, L Tovey

BHP Western Australian Iron Ore (WAIO) operations use a suite of slope monitoring systems which are deployed to operational areas based on the ground control risk. Slope Radars are one system used within WAIO, having recently deployed and integrated a network of 22 radar systems across the operations. The integration required the development of supporting network architecture, infrastructure, virtualised hosting, security protocols and a technology support model. This has enabled data transfer between the physical radar systems located in open pits, to on-site offices, a vendor supported remote control room in Indonesia and the WAIO Integrated Remote Operations Centre for data analysis and monitoring of system and displacement alarms 24/7. The typical technical skillset of a Geotechnical Engineer does not include the knowledge and capability to understand and develop the supporting IT infrastructure required for establishing an integrated radar monitoring network. This paper will provide a discussion of the technology considerations for integrating radar systems and highlight the importance of the developed partnerships between internal geotechnical and technology teams and the external vendor team to ensure a reliable, robust and scalable slope monitoring solution.

Nov 29, 2022

By M W. Chen, I Canbulat, S Saydam, C G. Zhang

The height of fracturing (HoF) measures the propagation distance of continuous fracturing from the mining horizon and is also termed the height of cracking (Hebblewhite, 2020; Khanal et al, 2019) or hydrologically the height of groundwater drainage (Tammetta, 2013). In longwall practice, HoF is an important predictive indicator for assessing the dewatering effect of panel extraction on the shallow aquifer and surface flows. The HoF determination is basically dependent on field measurement works, typically using surface extensometer, borehole televiewer imaging, piezometer monitoring, packer testing, borehole breakout logging, and isotopic tracer monitoring (Brown and Walsh, 2022; Corbett, 2022; Hebblewhite, 2020; Holla and Armstrong, 1986; Mills and O’Grady, 1998; Walsh et al, 2022a, 2022b). These methods or tools have been widely applied to observe rock fracturing and groundwater responses to longwalls at Australian coalmines, for example, Dendrobium Mine (Brown and Walsh, 2022; Walsh et al, 2022b), Appin Mine (Walsh et al, 2022a), and Springvale Mine (Corbett, 2022). In Chinese mines, borehole televiewer imaging and packer testing are more frequently used due to convenient instrumentation, quick testing, and not requiring long-term maintenance of the instrumentation boreholes. The HoF determination also involves further raw data interpretations, for which specialist software for data extraction and quantitative criteria for bounding the fracture transition and termination are necessary. By combining the measured fracture distribution and longwall parameters regarding panel geometry and geological settings, several HoF models have been developed for conceptualising the understanding of strata depressurisation and providing mine engineers fast calculation tools for HoF prediction. The Mackie model considered the height of fracturing as the upper bound of fractured zone and revealed that within the fractured zone there are highly connected fractures and accordingly porosity enhancement and groundwater depressurisation, where the fracture network can be less transmissive from the mining horizon up (Hebblewhite, 2020). The fractured zone shares similar fracturing regime but different heights in varying models: HoF is 30 to 58 times of the mining height (t) based on Australian, Soviet and UK experience (Kendorski, 1993, 2006), and 21 to 33 t according to the field measurements in NSW Central Coast, Australia (Galvin, 2016). Some Australian longwall mines adopt Ditton model (Ditton and Merrick, 2014) (Equations 1.1 and 1.2 in Table 1) sourcing from NSW coalfield experience for HoF prediction, while Liu model (Liu, 1981) (Equations 2.1 to 2.4 in Table 1) developed from 27 coalmines in China is frequently used by Chinese coalmines.

Nov 29, 2022

By I Canbulat, J Emery, L Yao and C Zhang

This paper documents a process of data analytics and machine learning applied to coalmine roof convergence data. It follows a publication documenting the formation of the database. For each set of analyses Python scripts were utilised to extract data from an SQL database, with subsequent analyses also executed in Python, utilising open-source tools such as scikit-learn. Preliminary analyses with classic machine learning algorithms included multiple logistic regression, K-nearest neighbours, decision tree, random forest, support vector machine, kernel support vector machine, artificial neural network (ANN), naïve Bayes and multiple linear regression. Results indicated that relationships were complex and non-linear, with the artificial neural network most suitable. An ANN model was then refined through a standard process of hyperparameter optimisation and data augmentation to arrive at a final model. Due to the black box nature of the ANN further insight into how the parameters interacted was sought and found with Shapley additive explanations (SHAP values). SHAP values utilise Game Theory, where each input parameter or feature is a ‘player’ while the data set is the ‘team’. The SHAP value is the impact of each player on the target value, essentially establishing the contribution of each input parameter. The results from all analyses are delivered in the paper, together with insights, applications, strengths, and limitations of the methodology.

Nov 29, 2022

By B Banerjee, N Kumar, S Parihar

Rampura Agucha Pb-Zn Mine (RAM) is located about 200 km to the south-west of Jaipur in the state of Rajasthan, India. Open pit mining operations commenced in 1988 and continued to 2018. RAM open pit footprint is the largest in India with length of 2000 m, width 1500 m and depth of 400 m. Development of an underground mine under the operating pit commenced in 2013, through trial mining longhole open stoping with cemented backfill was established as a preferred mining method. Nine years in operations underground mine has reached the production capacity of 4.5 MT, which represent more than 70 per cent of the ore volume mined by the pit. RAM is currently the world second largest underground Pb-Zn mine.

Nov 29, 2022

By X Z. Sun, N Jiang, J H. Zhao, C X. Wang, L Y. Bai

In backfill grouting for underground coalmines, the filling materials strengthen the caving rock and support the overlying strata to reduce surface subsidence. The broken roof strata fail and collapse during mining operations without appropriate supporting measures being taken. It is difficult to perform continuous backfill mining on the working face of such roofs using the existing mining technology. Therefore, in order to solve the above problems, fly ash and mine water are considered as filling materials, and flow characteristics of fly-ash slurry are investigated through laboratory experiments and theoretical analyses. Laws governing the diffusion of fly-ash slurry in the void of caving rock masses and in the void between a caving rock mass and a basic roof are obtained and verified. Based on the results obtained from the above analyses and field conditions at the Zhaoguan coalmine, Shandong Province, China, a cave backfill grouting system of the hauling pipeline is developed and successfully tested at the 1703 working face. The results demonstrate that a filling rate of 43.46 per cent is achieved, and the surface subsidence coefficient of the grouting process is found to be 0.475. Compared to the total caving method, the proposed system is found to achieve a reduction rate of 40.63 per cent. This effectively helps in lowering the value of the surface subsidence coefficient. Fly ash and mine water, considered as primary materials in this study, also play a significant role in improving the air quality and water environment.

Nov 29, 2022

By Y Tsukurimichi, D Asahina, T Endo, T Takemura

Scientific knowledge of Mars’ surface morphology and internal geological structure has been accumulated through satellite imagery and numerical topographic data using remote sensing technology, as well as seismic surveys by the on-site lander. Recent studies show that Marsquakes could be caused by the release of strain energy generated by the contraction of Mars. In particular, Marsquakes occur around the graben where many faults are existed and formed regularly spaced patterns. This implies that Marsquakes occur when the stress field of the Martian crust is an extension condition, and normal faults appear on the surface. We focus on the linear relationship between the fault spacing and the thickness of the mechanical layer as an approach to studying the internal structure from satellite images. Mechanical layer is a layer that composes of the same mechanical properties and is mainly bounded by lithology (Narr, 1991; Gross, 1993). The linear relationship between the thickness of the mechanical layer and the joint spacing has been studied and its slope is called the Fracture-Spacing Index (FSI) (Narr and Suppe, 1991). Soliva, Benedicto and Maerten (2006) showed that the stress drop zone (stress shadow) due to the fault activities affects the fault spacing. Figure 1 shows the approach used to estimate the thickness of the mechanical layer from the fault spacing on Mars. This paper aims to better understand the internal mechanical structure of Mars estimated by the geometrical pattern of faults on the Martian surface. We report the initial studies of this work. The lab-scale physical experiments and numerical experiments were presented to demonstrate the relationship between the thickness of the mechanical layer and the geometric pattern of fractures

Nov 29, 2022

By H A. Linn, K Winn, C W. Lee

The Q-slope method for rock slope engineering was developed to enable engineering geologists and rock engineers to rapidly assess the stability of excavated rock slopes in the field and make optimal adjustments to slope angles as rock mass conditions become apparent during construction of road cuts or benches. An empirical relationship between Q-slope and long-term stable slope angle is now supported through over 500 cases studies from Asia, Australia, the Americas and Europe. This paper presents about the stability analysis by first-ever applying Q-slope method on abandoned quarry wall in Singapore. The 30 m high rock slope which is composed of monzogranite rock was severely damaged by blasting operation. As the rock slope is intended for public view the objective was to retain the natural outlook and without any artificial support application thus manual scaling was carried out to clear the loosed rock blocks. In the end stable slope angle of clean rock face is determined once again by Q-slope method.

Nov 29, 2022

By A Mcquillan, N Bar

Geotechnical models developed during the open pit mine planning stage are generally three-dimensional (3D) in component to capture the spatial variation in geological, structural, hydrogeological and geomechanical conditions. Yet when geotechnical analysis is completed, often the 3D geological, hydrogeological and structural models are simplified to two-dimensions (2D). This paper demonstrates this simplification, through referenced case studies, can lead to the wrong failure mechanism being analysed and/or a conservative Factor of Safety (FOS), or Strength Reduction Factor (SRF), being calculated, leading to a false sense of stability. There exists a paradigm that the FOS calculated using 2D limit equilibrium (LE), or the Strength Reduction Factor (SRF) calculated using 2D finite element (FE), modelling methods is generally conservative, ie lower, than the true FOS. However, this assumption that 3D FOS, or 3D SRF, is always higher than 2D FOS, or 2D SRF, is not always correct (Chen and Chameau, 1983; Bromhead and Martin, 2004; Herza et al, 2017; Pyke, 2017; Dana et al, 2018).

Nov 29, 2022

By C Jacobsen, N Harries

Assessing and managing instability hazards is an essential activity when working with unstable natural slopes and excavated open pit mining slopes. Slope monitoring has become the standard technique for the management of geotechnical risks associated with mine slope instability hazards. In recent decades, a proliferation of new monitoring techniques such as terrestrial radar, satellite InSAR and LIDAR have become standard operational tools, complementing conventional survey-based monitoring solutions. A reliable monitoring system should identify and record incipient anomalous slope movement. Although the most obvious purpose of a monitoring system is safety related, slope deformation and performance monitoring also enhance the understanding of slope behaviour and assists in improving system design and implementation. For a monitoring system to be considered an effective early warning tool, it needs to operate in real-time and should be linked to the mine’s emergency communication systems. Terrestrial radar systems have been developed that can provide near real-time measurements, at a high level of precision and covering broad areas in all weather conditions. This has had a positive impact on the management of geotechnical risks in operational conditions. The technology adoption of RADAR in mine monitoring has significantly progressed in the last 20 years from technology enthusiasts, to visionaries, to pragmatists to conservative users. However, the increasing adoption of RADAR cannot reduce or remove other monitoring techniques that often have important benefits; even if these technologies cannot be used as a real-time operational tool. An increasing awareness on the importance of combining data from different monitoring techniques to develop a holistic picture of all possible geotechnical hazards is a current industry trend. This is proving to be an excellent foundation for managing hazards associated with slope instability in open pit mines, and is only expected to improve with time with the adoption of new technologies based on big data and Artificial Intelligence (AI).

Nov 29, 2022

By Z R. Guo, Y Qiu, X F. Wang

Mechanical damage leads to the increase of effective stress of sediments, and pore closure hinders the discharge of methane gas. Ignoring the influence of mechanical damage leads to an excessive prediction of hydrate gas production. Therefore, a fully coupled model considering mechanical damage-chemical decomposition-gas-water two-phase seepage-temperature was developed in this study, and the model was verified by Masuda experiment. Based on the fully coupled model, the temporal and spatial evolution of the whole process of hydrate decomposition under the influence of three initial absolute permeabilities, three pressure drops and three water saturations were considered. The results showed that: • The gas production rate reached the peak value in a short time after depressurisation, and the peak value increased with the increase of the absolute initial permeability. The larger the initial absolute permeability was, the faster the damage variable reached the peak value. The porosity increased gradually before the damage variable reached its peak, and the gas flowed more easily. • When the pressure drop was low, the hydrate remained stable in solid form. As the pressure drop increased, the hydrate gradually began to decompose. The greater the pressure drop was, the faster the initial decomposition rate of the hydrate was. So the damage variable increased rapidly and the porosity increased continuously, resulting in a large gas production rate at the initial stage of decomposition. • The larger the initial water saturation was, the smaller the effective stress wss, resulting in the slow growth of the damage variable and the small change of porosity.While the gas relative permeability was small, it resulted in a smaller gas production rate, and hydrate decomposition was slower. • The damage variable showed a process of rapid growth first, then slowly increased to the peak, and then gradually decreased to a stable state. When the damage was considered, the hydrate decomposition time to the steady state was longer, and the gas production was about 80.68 per cent of that without considering the damage.

Nov 29, 2022

By D E. Tennant

In the fields of geotechnical engineering and slope management, various software packages are used to assess the behaviour or propensity for a slope to fail. Traditional kinematic analysis calculates the probability of failure of design sectors with respect to dominant structural set orientations. A novel methodology is provided here to view potential hazardous slope behaviour in 3D, allowing engineers to make informed decisions regarding various pit slope geometries. Apparent dips are calculated for every point in space with respect to every slope orientation of the entire pit surface/design, specifically in reference to bench and inter-ramp planar failure mechanisms. Implementing a proactive approach to slope design will not only lead to early mitigation of risk but can also add direct value by enhancing or improving upon slope angles for earlier access to ore. From a safety perspective, identification of unfavourably oriented slope geometries can be dealt with before failure occurs. This methodology relies on a strong understanding of the existing rock mass anisotropy, particularly behind the face, thereby removing some of the uncertainty surrounding pit design as well as presenting engineers with an additional means to manage risk.

Nov 29, 2022

By C Balci, D Tumac, A Sheterpour-Mamaghani, E Dogan, A Kocbay, T Erdogan, A Gumus, H Copur, E Altintas

Excavation of vertical and/or inclined shafts in the underground structures requiring careful design and planning. Raise Boring Machines (RBMs) are commonly used for excavation of shafts for different purposes such as ventilation, orepass, and human-material transportation. Proper selection and accurate performance prediction of RBMs are two main parameters affecting the cost estimation and planning/scheduling. Indentation test is one of the most preferred methods that can be used to predict advance rate of RBMs. This study aims at suggestion of new prediction model for instantaneous penetration rate of RBMs based on indentation tests. Different rock (core) samples (with different geological origins) are obtained from the raise boring application projects in Turkey; then, the indentation tests are carried out on them by using a real-life insert (button), which is used in reamerhead cutters investigated in this study. Finally, the statistical relationships between the field performance and the indentation indices are investigated. The study indicates that the brittleness index (the ratio of maximum applied force to corresponding penetration) can be used to predict instantaneous penetration rate of RBMs used in the vertical raise bored shafts excavating rocks having uniaxial compressive strength lower than 100 MPa.

Nov 29, 2022

By S Yang, J Wang, J G. Ning

A series of conventional dynamic uniaxial compression (CDUC) tests and coupled static-dynamic loading (CSDL) tests were conducted using a split Hopkinson pressure bar (SHPB) system to explore the dynamic mechanical behaviour and fracture characteristics of medium sandstone on a microscale in the laboratory. In the CDUC tests, the dynamic uniaxial compressive strength of the medium sandstone was rate-dependent, while the dynamic elastic modulus was not dependent on the strain rate. Then, we proposed a generalised model to characterise the rate-dependent strength from 17.5 s-1 to 96.8 s-1. In the CSDL tests, with increasing initial pre-static stress, the dynamic elastic modulus and dynamic strength increased nonlinearly at first and then decreased. The results show that two classical mechanical types (ie Class I and Class II) are observed from the dynamic stress-strain responses of the CDUC and CSDL tests. By means of scanning electron microscopy (SEM), the micro difference of post-loading microfracture characteristics in Class I and Class II behaviour was identified. In Class I behaviour, intergranular fracture (IF) usually initiates at or near the grains, most cracks deflected along the grain boundaries, resulting in a sharp angular edge, then coalesces to the main fracture surface that splits the specimen along the direction of stress wave propagation. In contrast, Class II behaviour results from the combined IF and transgranular fracture (TF).

Nov 29, 2022

By E Ben-Dor, D Bakun-Mazor, Y Ben-Ari

Determining the mechanical properties of rocks is important for various civil engineering fields, including the mining of raw materials for aggregates used in the construction and paving industries. Traditionally, the mechanical properties of rocks are obtained through in situ and laboratory tests during geotechnical surveys. However, these time-consuming surveys involve many resources. In contrast, hyperspectral remote sensing methods make it possible to identify the mineralogical composition and crystallographic structure of the rock; properties that control the mechanical properties of the rocks. In this work, we characterise the mechanical properties of carbonate rocks by using a hyperspectral sensor in laboratory conditions. We collected about 150 cylindrical samples of carbonate rock, with a wide range of strength values from several rock outcrops in Israel. We used a point spectrometer in the range of 0.4–2.5 μm and a spectral image sensor in the range of 3.0–12.0 μm, scanning the samples to obtain the signature of their light reflections and spectral emissivity. We then measured the samples’ density, porosity, water absorption, and uniaxial compressive strength (UCS). We used sophisticated data mining to find statistical relationships between the hyperspectral signatures of the samples and their mechanical properties. We used this data to identify the most dominant wavelengths for predicting mechanical properties. We found that the density, porosity, and water absorption of carbonate rocks could be confidently predicted based on spectroscopy data, while the UCS of the rock could also be predicted, but less significantly. The results of the study pave the way for the development of measuring tools for the mechanical properties of rock, based on non-destructive tests of quarrying materials.

Nov 29, 2022