Search Documents

By Jin Liu

In the early 1990?s, Inco successfully installed two new flash furnaces as part of their SO2abatement project to reduce SO2 emissions from the Copper Cliff Smelter by 60%. The flash furnace off-gas is cooled and cleaned through two new Monsanto Dynawave gas cleaning systems that replaced the traditional venturi scrubbing system. It was discovered that the flash furnace production capacity is often limited by the capacity of the gas cleaning system. The key task is to eliminate pressure drop from the system. The froth column is responsible for by far the largest pressure drop in the gas cleaning system. Initially, the column was fitted with 22 plates. In 1994, both #1 and #2 froth columns were modified by reducing the number of plates in each column from 22 to 18 and increasing the interplate spacing on lower plates. With increasing demand for more throughput in the flash furnaces, further modifications on the froth columns were made in 2005. This paper describes these modifications and results together with some fundamental analysis of the froth column characteristics.

Jan 1, 2006

By T. Innmi

The potential of the nickel matte anode was measured during the matte electrolysis in the commercial cell. The slime layer consists of elemental sulfur and was found to greatly influence the potential of anode. The measurements of porosity and permeability of the slime suggest that the voltage drop of the slime layer dominates the potential. Furthermore, the diffusion of the electrolyte through the slime layer is also one of the factors to determine the potential. In addition, the copper content of the nickel matte anode was found to affect the change in the anode potential during the electrolysis. The role of copper on the anodic dissolution of nickel matte is discussed in this work.

Jan 1, 1988

By Paul S. Korinko, Simona E. Hunyadi Murph

To address a radiological contamination event, a materials and process project was initiated. During the course of this project, processes and materials were developed that successfully captured zinc vapors physically and chemically, respectively. However, the physical traps were placed in an undesirable area and it was determined that the chemically captured zinc reactions was reversible. Consequently, advanced nanomaterials are being developed to capture zinc vapors. The current state of the art of the science and engineering of these materials and their efficacy for zinc capture and retention is discussed in this paper.

Jan 1, 2015

By David Tisdale, Phillip Mackey, Nagendra Tripathi, Matthew Kreuh, Pascal Coursol

Xstrata Nickel’s Sudbury smelter operation is based on fluid bed roasting of Ni-Cu sulphide concentrate, followed by electric furnace reductive smelting and Peirce-Smith converting to produce a Bessemer matte for electro refining, along with sulphuric acid produced from smelter gas. While the site dates back to the 1930s, the present smelter configuration has been operational since 1978, and currently has a nominal capacity of about 67,000 tpy of contained nickel and is investigating options to expand in future up to 85,000 tpy. As part of a review of plant capacity options, a new metallurgical model of the plant was developed in order to examine a number of processing alternatives. Based on the METSIM™ platform, the present model includes the ability to examine the impact of a number of plant parameters on potential plant performance including; for example, the following: percent of sulphur elimination in roasting, matte grade, degree of matte metallization, temperature, coke requirements, sulphuric acid production, CO2 emissions and overall energy requirements. The process model also includes a number of special features adopted; for example, approaches to effectively model the complex Ni-Cu-Co-Fe-S-O matte system. This paper provides a description of the model and gives an overview of the results. As well as presenting the results of the present study, the applicability of this modeling approach to pyrometallurgical systems in general is also briefly discussed in the paper.

Jan 1, 2009

By Mahin Rameshni

WorleyParsons innovative SO2 reduction process efficiently recovers sulfur from SO2 streams. Effluent gases from ore roasters and smelters and coal-fired power plants can be treated to reduce sulfur emissions. This exciting new process is an innovative combination of well-established processes of reaction of CH4 and sulfur vapor to produce CS2, followed by catalytic hydrolysis of CS2 to H2S, and Claus reaction of H2S and SO2 to sulfur. Key advantages are lower fuel consumption, reduced emissions, better product sulfur quality and better operational stability. The Production of elemental sulfur from SO2 is being called Rameshni SO2 Reduction (RSR) and it is patent pending.

Jan 1, 2006

By T. Wang, R. G. Reddy

"The corrosion of stainless steel SS316L in a low melting point novel LiNO3-NaNO3-KNO3- NaNO2 eutectic molten salt mixture was investigated at 695K. After long-term isothermal dipping corrosion experiments, the SS316L samples were analyzed using scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS) to determine the topography and corrosion products. Dense and protective lithium iron oxide scale formed on the surface and prevented the SS316L sample from further severe corrosion. Therefore, SS316L is considered to be suitable construction material for solar thermal energy storage materials containers.IntroductionMolten salt mixtures have been considered as potential candidates for thermal energy storage and heat transfer media in solar energy applications. To apply the molten salt in the energy transfer process, the standard pipes made of stainless steel must be utilized to carry the molten salt mixtures in parabolic trough system of solar power production. The pipes encounter continuous flow of hot and cold molten salt every day. Thus corrosion of stainless steel in molten salt mixtures becomes extremely essential for the long-term utilization of the thermal energy storage media. The corrosion of passivity materials inside high temperature molten salt systems have been studied which gives fundamental understanding of basic mechanism about the corrosion process [1-8].The corrosion behavior of Fe-Ni-Cr alloys in an equi-molar LiNO3–NaNO3–KNO3 mixture was studied [9]. According to the XRD analyses, the major phases in the oxide scales were identified as LiFeO2, Fe3O4 and Cr2O3. A HITEC® salt mixture (NaNO3–NaNO2–KNO3) was also tested as a corrosion medium for stainless steel [10] and the corrosion rate was found to be affected by the protective oxide layer. In most cases, the alloys having more than 10wt% chromium show high resistance to corrosion in molten salts."

Jan 1, 2014

By Jeff M. Kuhn

A new solvent extraction process for the removal of halides from zinc sulphate solution was tested in pilot plants at both a 0.1-L/min scale and at a 3-L/min scale. Teck Cominco?s process is called the HalogonTM process, for which patents are pending. Mixer-settlers were used for the 0.1-L/min pilot scale and two BATEMAN pulsed columns for the higher rates. Pilot testing was performed with commercial zinc sulphate solutions containing variable amounts of chloride and fluoride. Sulphate extraction was also controlled and deleterious halides were loaded and stripped into a form suitable for disposal. The engineering aspects and economics of this solvent extraction process for halide removal are also reported.

Jan 1, 2003

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By Mark Kruzynski, Srinivas Garimella, James T. Wiswall

"A flue gas recirculation (FGR) system for a combustion fired aluminum melting furnace is experimentally investigated. The FGR system flows combustion air in a turbulent jet within the flue gas stream, and the turbulent jet flow is collected in a tube at a distance from the jet exit. Entrainment of the flue gases as well as heat transfer between the flue gases and the jet occurs over the length of the exposed jet. Heat transfer between the flue gases and the jet, and the amount of flue gas entrained into the jet (derived from temperature, flow rate and oxygen fraction measurements) were measured as a function of nozzle exit velocity and the distance between the nozzle exit and collection tube. In addition to flue gas entrainment, a fuel savings of up to 7%, due to heat transfer over the length of the jet, was projected from the measurements obtained.IntroductionFlue gas recirculation can be applied to aluminum melting furnaces to control combustion temperature. When coupled with a device to improve furnace efficiency by recovering heat from the furnace exhaust, flue gas recirculation provides a control technique that is integral to achieving the goals of reducing fuel consumption, increasing product yield, increasing the longevity of infrastructure, and reducing pollutant emissions. In particular, combustion temperature control can help reduce reactivity of the products of combustion with the molten metal surface and furnace refractory materials. Combustion temperature control can also help improve the life of heat exchangers used to recover energy lost to the environment in the flue gases, and reduce NOx formation in the combustion process. Flue gas recirculation can also dilute oxygen used in oxy-fuel combustion to reduce reactivity.Flue gas recirculation has been used since the 1970s to control flame temperatures in the automotive industry [1-3] and has successfully reduced NOx emissions. Many different flue gas recirculation approaches for high temperature melting such as melting aluminum and glass have been patented since the 1980s [4-12]. There has also been academic interest to determine the fundamental performance characteristics of flue gas recirculation in high temperature furnaces and in combustion [13-15]."

Jan 1, 2014

By R. H. Crist

Reactive components of algal cell walls include uronic and alginic acids: In addition, many marine species have half ester sulfate groups which function as fixed anions. Associated metals vary with the media, eg., Ca and Mg in fresh water (FV) and Na, Ca, Mg in seawater. . These metals readily exchange with aqueous phase protons or metal cations. A plot of the total amount of metal cations displaced by protons vs .. pH shows one inflection at pH 4 for FV algae and' in addition a second inflection at pH 2, 3 for marine algae. The first inflection is interpreted as. Indicating the cations associated with carboxyl groups ,and the ,second with half ester ?Sulfate groups. The exchange capacities of various aigal ,species vary widely. When FV algae is placed in a Pb2+ solution,- the amount of Pb2"' deposited on the algae is. Equivalent to the. Total Ca2?, Mg2, and H+ displaced? thereby confirming the ion exchange mechanism. Ion exchange equilibrium constants are reported for the displacement of ca2+ from Vaucheria. With Mg2+, sr2+, Cd2+, Pb2+_ and Na+ as well as the reverse reactions. Cd2+ can .be removed partially from algae by precipitating it as CdS or Cd(OH) 2 Pb2+ and Cu2+ are also partially removed as the hydroxides. Rates of reaction for various alkali hydroxides decrease with increasing .unhydrated cation radius. It is concluded that theory is useful in predicting viable applications for algae in pollution abatement.

Jan 1, 1991

By Michael E. Stout

The recovery of the constituent components of spent lead acid batteries was pioneered in the early 1970's by M.A. Industries, Inc. MA's main reason for research and development in this area was to recover the polypropylene casings for use as feed stock in their injection molding plants. At that time spent and reject casings were either disposed of or being fed with the lead 'bearing materials into the ,smelting process. M.A. has since developed, built and operated plant for the conversion of scrap casing into reusable copolymer resins. The system is composed, of washing, .sizing, extrusion and pelletizing the polymer into a form which is ready to be injection molded into new products.

Jan 1, 1995

By Sebastiaan Peelman

NdFeB permanent magnets are the best available magnets used in many technology applications. However, at their end-of-life (EoL) most of magnets and the contained REEs are lost during the recycling of the bulk metals. The REEs are classified as the most critical raw materials in the European Union, and recycling of REEs from EoL products will reduce their criticality and contribute to the sustainability of REE. Various technological routes have been reported, but most of the methods are effective for highly concentrated magnets or magnet scrap, which is greatly dependent on expensive pre-dismantling processes. This paper presents various innovative metallurgical solutions to the effective REE recovery from current industrial practice for WEEE recycling, including the ferrous scrap from WEEE shredder products and shredder residues from computer hard disk drives. Both hydrometallurgical and combined hydro- and pyrometallurgical REE recovery routes are developed after demagnetization and physical upgrading.

By Juan Hernández Ávila

This work studies the Molybdenum effect on the microestructure, mechanical properties of an as-cast ductile iron. For this study five ductile irons with different amounts of Molybdenum each were made in an induction furnace. In this material nodule count and nodularity is affected by the Molybdenum additions; The iron´s matrix, nodules and the phase were analyzed using scanning electron microscopy detecting Molybdenum only in the matrix. Mechanical properties such as hardness, microhardness, tensile strength and yield strength show increments as the Molybdenum amount is increased. In the same way, ferrite and pearlite phases display a variation in their percentage as the contents of the alloy element increase. This element has a marked influence on the pearlite interlaminar spacing. From the obtained results we conclude that Molybdenum in these quantities dissolves in solid ferrite solution during the solidification process, improving the material´s mechanical properties.

Jan 1, 2009

By Shunhong Huang

Thirty-five soils were sampled from three sites at different distances from chromium slag heap of a Iron-alloy factory, namely, nine from site A located under the chromium slag and eighteen from Site B in the vicinity of the factory and eight from site C far from the factory. The contents of total Cr in these soils from site A, B and C were 1666.0±1310.9 mg? kg - 1,1136.2±1844.6 mg? kg - 1 ,300.4 ±165.1 mg? kg ? 1, respectively. The contents of water soluble Cr were 59.3±77.57 mg? kg ? 1,0.6 ±0.3 mg? kg - 1 ,0.5±0.3 mg? kg - 1 , respectively. In order to evaluate soil health, the activities of four soil enzymes (catalase, polyphenol oxidase, dehydrogenase, alkaline phosphatases) were analyzed. The results have shown that dehydrogenase activity was greatly depressed by conditions in the heavy chromium-contaminated sites. Negative correlation was observed between dehydrogenase activity and the distance from the chromium slag heap, however, the activities of catalase, polyphenol oxidase, alkaline phosphatases in soils from the three sampling sites mentioned above did not differ significantly. The result imply that of dehydrogenase activity could be used as an indicator for the chromium pollution level in the area of Iron-Alloy factory and for the stability level of the soil ecosystem.

Jan 1, 2008

By Malti Goel

"Technology advancements in fossil fuel based energy generation and consumption are currently being aimed at minimization of CO2 emissions. To attain energy security, India must accelerate the pace of economic development, while achieving reduction in CO2 emissions per unit of energy consumed. It would need access to advanced coal utilization technologies to be demonstrated on indigenous coal characteristics. Of specific importance would be: improvement in coal quality, increasing energy efficiency and suitability of other CO2 sequestration technologies for reducing CO2 footprints. There is need to address related risks and financial burden through adoption of policies and regulations including the issue of open access in energy research. In this paper, seven important areas of strategic plan that need to be pursued for managing CO2 emissions in steel energy sector in India are discussed.IntroductionWorld is facing a crisis of climate change, which follows in the footsteps of global energy and environment crises. Accumulation of carbon dioxide from the generation and utilization of energy is leading to greenhouse warming and climate change. The global warming is causing the boundary between four seasons to be fuzzy and resulting in more spiky weather. Significance of its impact on environment is also determining the technology development needs in various sectors of economy for taking remedial measures.To respond to climate change concerns, the steel industry is undergoing a transition. It is at the threshold of a rapid change in technology as it targets innovation to achieve 50% reduction of CO2 emissions per ton of steel produced. Fossil fuel use is the main contributor of increasing concentration of carbon dioxide in the atmosphere. The control of air pollution and CO2 capture are thus relevant for a coal based industry, whether thermal power plant or a demand side energy intensive industry. World steel production has shown phenomenal increase in first eight years of 21st century increasing from 780 Mt in 2000 to 1343 Mt in 2008 [1]. It was merely 28 Mt in 1900. The global CO2 emissions from steel industry are also increasing and became 2550 Mt (3-4% of total GHG). Indian industry contribution was 161 Mt (15% of direct emissions from industry). It is likely to grow further to keep pace with the accelerated economic growth of 8-9% per annum."

Jan 1, 2010

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

By J. R. Rendón

Cylinders of commercial aluminium alloy 6063 were homogenized under different conditions. The experimental results indicated that the general mechanical behaviour as related to curves of 0.2% yield strength, ultimate tensile strength and Brunnell hardness versus homogeneizing process is the same in both cases. The mechanical properties as compared to those required by plant specifications, tend to be better with increasing values of % Mg2Si in the alloy, as expected. The electron microscopy investigations revealed that in both homogeneizing processes the resulting microstructure consist of significant spheroidizing of the alpha phase (AlFeSi) and fine-needle type structure of beta phase. The alpha phase was also present in a Chinese type scripture. Furthermore, the slow cooling within the furnace resulted in the nucleation and growth of Mg2Si precipitates generally along the grain boundaries.

Jan 1, 1997

By Feng Gao

A general unsteady- state model, based on a cracked substrate, has been developed to account for reaction and diffusion within porous substrate during oxidation of Carbon Fiber Reinforced Carbon matrix (CIC) composites. The effects of several parameters, such as diffusion and reaction rate ratio, oxygen concentration, and composite density, on oxidation process are explored. Also, theoretical results for a set of parameter values of the CIC composites are compared with experimental data. It shows that the model predicted values agreed well with the experimental data in weight loss. Based on this model, quantitative predictions of oxidation of a composite with cracked substrate can be made.

Jan 1, 1993

By E. Fregeau-Wu

The mineralogy and grain size distribution of phases in a steelmaking slag and experimental products from the heating of the slag under various conditions were determined to explore the possibility of recycling of the iron and manganese to the blast furnace. The steelmaking slags consisted of three major phases: dicalcium silicate, dicalcium ferrite, and Mg-Mn-wustite. Most of the phosphorus was contained in the dicalcium silicate and to lesser extent in the dicalcium ferrite. Due to the fine grain size of the dicalcium silicate, grinding and magnetic separation required pretreatment to increase the grain size and hence the liberation. Experiments on a steelmaking slag were conducted by heating the slag to 1633-1748°K( and slow-cooling in an inert atmosphere at various rates with or without the addition of fluorspar (CaF2) as a flux. Grain size distribution analyses of the starting material and the slow-cooled products were performed using the SEM-IPP area scan method and the QEM*SEM linear scan method. Comparable and reproducible results were obtained on the same sample using both methods. A size versus volume percent plot showed the increased grain growth most effectively. Examples of the grain size distributions obtained were used to show that a higher soaking temperature prior to slow-cooling, a slower cooling rate, and the addition of fluorspar to the slag promoted grain growth.

Jan 1, 1989

By Chan. C. L., Zehr. R., M. M. Chen, J. Mazumder

"Two three-dimensional models of a surface tension gradient driven flow during laser surface heating are developed. The first model is based on a perturbation solution. The basic solution corresponds to the stationary axisynwnetric case and perturbation is based on a small scanning velocity. The advantage of seeking a perturbation solution, as it turns out, is that the three-dimensional flow is modeled by two sets of two-dimensional equations which are presumably much more tractable than the original three-dimensional equations. Numerical solutions are obtained and discussed. The second model is a full three-dimensional numerical solution of the Navier-Stokes equations, using a point-by-point partially vectorized iteration scheme. Surface shape is also determined in a self-consistent manner. The effect of the presence of convection on pool geometry, cooling rate and solute redistribution is presented and discussed.IntroductionThe existence of fluid flow and convection and their effects were first reported in the fifties (1,2). The role of convection in controlling pool geometry such as pool shape, undercut and ripples, and defects such as variable penetration, porosity and lack of fusion and weld properties such as weld homogeneity and bead formation is studied by a number of researchers and is reviewed by the authors in a recent paper (3).Recently, surface tension gradient driven flow has been identified as one of the forces responsible for convection within the molten pool (4,5). It is postulated that surface tension gradient driven flow is responsible for the surface ripple formation in the weld pool (6-8). Oreper, et al. (9) developed a two-dimensional convection model. Buoyancy, electromagnetic and surface tension gradient forces were considered. The formulation was based on a specified pool profile. It was found that the surface tension gradient is the dominant force in most cases. However, the solid-liquid interface is not known a priori. In fact, the solid-liquid interface, i.e. the pool shape, is a piece of information that the model should be able to predict. A two-dimensional transient self-consistent (i.e. the solid-liquid interface is solved as part of the solution] model for laser surface melted pool was first developed by Chan, Mazumder, and Chen (3)). This model predicted a non-uniform cooling rate, hence non-uniform microstructure. Depending on the Prandtl number (i.e. material) and surface tension number, the shape of the molten region as well as the cooling rate changes. It was also predicted that the recirculating velocity is of one or two order of magnitude higher than that of the scanning velocity. This model provides the detail of the flow field and heat transfer on a plane perpendicular to the scanning direction. However, the front-to-back motion and its effect on heat transfer also play important roles in the physical process, especially for the fact that the recirculating velocity is so much higher than the scanning velocity. Such a motion cannot be obtained from two-dimensional models."

Jan 1, 1986