Search Documents

By N. S. Raghavendran

Based on the weld pool length and width calculations due to an empirical model (1) for submerged arc weld metal, an elegant quantitative definition of tandem submerged arc welding is established. On the basis of this theoretical consideration optimum welding parameters for joining 25 mm thick low carbon steel plate in two passes by tandem wire submerged arc welding have been experimentally found out. An assessment of the metallurgical quality of weld metal and the dependence of mechanical propenies on pool overlap has been made. Also the solution of Rosenthal (2) etc. for a moving point source of welding, which was used as a guide line in formulating the empirical model for the calculations of weld pool dimensions, is compared with the solution of empirical model for submerged arc weld pool dimensions.

Jan 1, 1990

By ZHANG Ting

In view of the high consumption and contamination of traditional vanadium extraction technology, a new process of leaching the converter vanadium slag without roasting with titanium dioxide waste was proposed. Extraction mechanism of P204 in the leaching solution had been researched and single factor experiments show that after a prereduction of Fe, and under conditions: ambient temperature，leaching solution original pH=2.5, phase ratio (A/O)=1:3, shaking time 8min, the extraction rate of V is more than 98.62% meanwhile the separation rate between V and Fe is up to 135.3 in the 20%P204-10%TBP-Sulfonated kerosene extraction system.

Jan 1, 2015

By Yanhui Liu, Xuewei Lv, Pingsheng Lai, Chenguang Bai

The purpose of this paper is to study the effect of slag basicity on the Si content in stainless steel master alloys prepared by smelting reduction of Fe-Ni-Cr sinters. Theoretical analysis focusing on the gas, slag and alloy phases of the smelting reduction process at 1600°C was carried out by thermodynamic calculation software----FactSage, showing that the increase of CaO within the slag can result in the decrease of Si within the master alloy. Experiments were also carried out in vacuum melting furnace at 1600°C , and chemical analysis method was used to detect Si content in the alloys. When the MgO content is 9.00%, the experimental results were consistent with the calculated values. However, when the MgO content rises up to 14%, the content of Si in the alloy reaches the maximum when SiO2 equals to 22.81%.

Jan 1, 2016

The U.S. Bureau of Mines investigated CaF2-assisted H2SO4 leaching to extract Mn from domestic silicate manganese resources. A pyroxmangite ((Mn,Fe)Sio3) ore containing, in pct, 34 Mn, 23 Si, 3 Ca, and 1 Fe was leached at 90° C for 3 h in a solution containing, in g/L, 12 Mn, 140 H2SO4, 130 (NH4)2SO4, and 5 CaFz. Manganese extraction of 92 pct was achieved. Manganese of greater than 99 pct purity was prepared by electrolyzing the purified pregnant solution at a current density of 50 mA/cm2. The current efficiency was 65 pct.

Jan 1, 1991

By Arpad E. Torma

The identification and characterization of lithographic iron and sulfur oxidizing bacteria in the 1940' s. opened up new possibilities and challenges for the mining and metallurgical industries. These were exploited during the 1950's and' 1960's, when it was demonstrated' that mining wastes and complex unused mineral resources could be economically treated by bacterially assisted heap and dump leaching processes?. During the 1970's this technology grew into a more structured discipline called "biohydrometallurgy". In the l980's efforts were devoted to the identification of a variety of organisms involved in naturally occurring leaching processes. Further efforts dealt with the elucidation, of leaching mechanisms; the leach ability of nickel, coban, zinc, and precious metals; the desulfurization of coal; and diverse biosorpion phenomena. The application of genetic engineering techniques for the improvement of microbial performance was also initiated?. Current trends in biohydrometallurgy include improvement of many of the techniques noted above, as well as application of leaching. technolog.ies to. environmental remediation scenarios. These activities afford considerable opportunities for research in the 1990's. For example, bioremectiation of abandoned mining and processing sites requires development of new and economically viable technologies capable of removing low concentrations of toxic metals from high volumes of solid and/or liquid wastes.

Jan 1, 1991

By G. T. Lapidus, O. J. Solis-Marcial

"The oxidative dissolution of copper from refractory minerals, such as chalcopynte, represents a technological challenge that has occupied hydrometallurgists for more than half a century. Innumerable processes have been suggested, but the majority operates at high temperatures or employs corrosive media. The origin of this refractory nature is the formation of passivating phases of iron(III) or copper. One option is to add non-corrosive ligands that complex these metal ions, thereby facilitating their dissolution. In the present work, the effect of acetone in sulfuric acid solutions was studied. The initial experiments were on chalcopynte carbon paste electrodes using cyclic voltammetry, where greater reactivity was observed. Later, leaching tests with hydrogen peroxide, cupric sulfate and ozone and, as oxidants, were performed. High extractions were achieved in three hours at 50°C. The solid residues contained the iron in the form of Fe203 and FeOOH.IntroductionChalcopyrite is the most important mineral of polysulfide copper ores [1] and accounts for approximately 70% of the world's copper reserves [2]. Currently, the copper present in chalcopyrite is extracted mainly by pyrometallurgical processes, which generate environmental concerns because of the formation of SO2 gas and submicron particulates [3]. The development of a less aggressive hydrometallurgical process for the extraction of copper would constitute a possible solution to these problems. For that reason, studies of the dissolution behavior of chalcopyrite are of great technological importance [4], However, the proposed oxidative leaching routes for chalcopyrite, generally at high pressures and temperatures, have not been implemented on an industrial scale, because of the elevated costs required to equal the high copper extractions obtained in thermal processes. These extreme leaching conditions are required because of the refractory nature of chalcopyrite. Passivation has been used to explain this phenomenon, although researchers have disagreed on the composition of the layer, which is various have assumed to be sulfur, copper sulfides, and iron-bearing jarosites or hydroxides [5]. If the latter compounds are the cause, an alternative solution would be the use of polar organic solvents in the oxidative leach to decrease the formation of the passivating iron layer. In this work, the influence of acetone on the oxidative leaching of a chalcopyrite concentrate at room conditions is explored."

Jan 1, 2012

By I. M. Ritchie

Cyanide owes its great success as a lixivant for gold to the great strength of the Au-CN bond. A replacement for cyanide must similarly be a strong complexant for gold (I) or gold (III). The various alternatives are briefly considered and it is concluded that only thiosulfate has a reasonable chance of replacing cyanide as a relatively non-toxic lixivant at the present time. However, there are considerable technical problems to be overcome before thiosulfate can be considered to be a realistic alternative to cyanide. Firstly, the leaching of gold using aerated ammoniacal thiosulfate with copper as a catalyst is a complex process which needs to be understood and controlled carefully in order to achieve maximum recoveries with minimum reagent losses. Secondly, there needs to be an option similar to the CIP process for recovering and concentrating the dissolved gold thiosulfate complex from pulps produced in the processing of low grade gold ores. The prospects for overcoming these technical' challenges are evaluated and discussed.

Jan 1, 1998

By Shen Shen, Paul R. Ohodnicki, Samuel J. Kemion, Vladimir Keylin, Alex Leary, Joseph F. Huth, Michael E. McHenry

"Recent DOE workshops highlight the need for advanced soft magnetic materials leveraged in novel designs of power electronic components and systems for power conditioning and grid integration. Dramatic weight and size reductions are possible in these applications through operating at increased frequencies. This manuscript discusses processing and composition design approaches for optimizing FeCo-based nanocomposites for higher frequency operation at 100 kHz and above. The proposed strategy involves starting with prior compositions known to exhibit high inductions, optimal field crystallization induced anisotropy, and excellent mechanical and high temperature magnetic properties. Proposed alloy modifications for the applications of interest would include increased amorphous phase resistance, optimum induced anisotropy, and minimized or carefully engineered magnetostriction. Relevant process developments would target reduction of ribbon thickness by optimizing the casting process or post-processing treatments such as chemical thinning or rolling. Three archetypes FeCo-based nanocomposites are described including near equiatomic FeCo-based, Fe-rich and Co-rich alloys.MotivationSilicon steels are widely applied for 60Hz utility-scale transformers [1]. For applications at high frequencies, however, Si-steels exhibit unacceptable losses and ferrites are typically used due to their high electrical resistivity and good soft magnetic properties [2]. However, the low inductions offerrites have limited their applications in power electronics. Developments in rapid solidification have led to amorphous metal alloys and controlled nanocrystallization processing has resulted in state-of-the-art amorphous/nanocrystalline nanocomposite soft magnets [3-5]. Commercial utility-scale transformers made with Fe-based amorphous materials have been demonstrated to result in significant energy savings with an associated reduction in greenhouse gas emissions [6]. DOE workshops held in 2010 emphasized a need for advanced soft magnetic materials for the next generation of power electronics. For advanced power conditioning and grid integration applications, frequencies of 20 kHz up to -1 MHz are of interest depending on the power level [7]. Here, we review previous work and discuss the approaches to optimize FeCo-based nanocomposite materials for high frequency applications."

Jan 1, 2012

By Shijie Wang

In pressure oxidation leaching of copper anode slimes, than 65% of the tellurium is m' cxtraoted during decopperizing. About l0- 15% of the selenium is also dissolved simultane¬ously by severe leach conditions. Current operation for the treatment of the leachate is to constantly recirculate the leach solution through a bed of copper turnings. The tellurium and sele¬nium are precipitated from the leach liquor as copper telluride and copper selenide and sepa¬rated from the solution by filtration. In order to improve the reaction efficiency and reduce the process cost, viz, minimize the copper addition, cut retention time, and reduce the energy consumption; a chemical reducing agent is studied and the cementation process tested in the laboratory. In this paper, the test results are presented and the process chemistry is discussed.

Jan 1, 2003

By J. V. Atwood

The U.S. Bureau of Mines has developed a novel Double Membrane Electrolytic Cell (DMEC) that exhibits unique features for recycling contaminated metals and metal alloys. The DMEC incorporates two anionic ion exchange membranes, separating anodic and cathodic regions of the cell. The ion exchange membranes prevent significant transport of unwanted cationic impurities to the catholyte from the impure anolyte while the anion/cation balance in cell compartments is maintained through the free movement of anions between compartments. The membrane barrier makes it possible to electro refine highly contaminated materials or to electrowin from solution while utilizing alternate anode reactions. Sinceanolyte and catholyte cross contamination has been eliminated, premium cathode products are produced. The DMEC has been tested at bench, pilot, and commercial scales. Configuration of the DMEC, cell operation, scale, up efforts, and significant design factors are discussed. Two separate recycling investigations utilizing DMEC technology are presented. The first investigation examines recovery of high purity cobalt and nickel from severely contaminated super aIloy scrap. The second involves? upgrading contaminated cobalt in the U.S. Government's National Defense Stockpile. Capital and operating costs for both potential applications are presented.

Jan 1, 1995

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By Zhucheng Huang, Zhikai Liang, Lingyun Yi, Tao Jiang

"In this study, reduction of iron ore pellets was carried out at 800-950°C by simulating the atmosphere of typical coal gasification gas. The effects of temperature, gas composition and reduction degree on swelling were investigated respectively. Reduction degree was obtained according to the weight loss records. And volume changes of pellets during reduction were evaluated by infrared photography. Results showed that the pellet swelling increased with temperature and decreased slightly with hydrogen content in the reducing gas. The swelling peaked when reduction degree reached about 40% and then decreased to be stable finally. The microstructures of pellets during reduction were examined by reflected light microscope and relatively rational explanations were proposed for their swelling behaviors.PrefaceDirect reduction iron is an important and indispensable raw material for high-purified and high-quality steel in the electric furnace smelting. Gas-based shaft furnace direct reduction process has very strong competitative ability; however, this technique requires natural gas as reducing agent, so its development has been restricted by gas source and area. Compared with gas-based reduction method, coal based reduction method has the disadvantages of higher production cost and lower productivity. In China, coal resources are abundant and coal gasification technology is mature, and the development of coal gasification shaft furnace direct reduction process is promising. [1] The gasification methods of fixed bed method (Lurgi method), fluidized bed method (Undok method), airflow bed method (Texaco coal water slurry method and Shell dry powder coal method) have been put into use successfully. These syngas generated by different methods can meet the actual production requirement of shaft furnace. However, the compositions of the effective reduction gas in the syngas are quite different. The ratios of hydrogen and carbon monoxide (H2/CO) of Undok or Shell coal gas, Texaco coal gas and Lurgi coal gas are 0.4, 0.6~ 1.0 and 1.6~2.3, respectively. [2] In the coal gas direct reduction process, the swelling behavior of iron ore pellets is various due to the differences of the gas composition, reduction temperature and reduction degree, and it seriously affects the normal operation ofDRI production. [3-9] Therefore, the research on the swelling behavior and its mechanism of iron ore pellets in direct reduction were carried out in this paper."

Jan 1, 2013

By Anupam Madhukar

The essence of an atomistic unified kinetic model of strained thin film growth and defect initiation is presented along with a comparison of its consequences obtained from computer simulations with experiments. Within the competing kinetics of a strain dependent activated incorporation of atoms and an asymmetry between upwards and downwards inter-layer migration, the model provides a consistent description of 2D versus 3D morphology evolution accompanied by the appearance of surface vacancies and steps at no energy cost. The correlated migration of these precursor defects offers an atomistic mechanism for the emergence of surface half-loops from the growth front (thus accounting for configurational and thermal entropy) governed by activation energies closer to their correlated motion under the evolving strain fields and thus substantially less than those calculated with respect to the perfect crystal as the reference state. The essential mechano-chemical nature of the problem is compared and contrasted with the historical literature of such phenomenon as precipitation hardening and sintering in metallic and ceramic composites.

Jan 1, 1994

By Bora Derin

This work deals with the recovery of valuable metals from the ancient copper smelting slags located in Küre-Turkey. In this process, copper and cobalt were recovered in metallic form and/or as their compounds, whereas iron was recovered as magnetic oxide or pigment. Abrasive grit material was produced using reduced final slag. The process stages involved carbothermal reduction in a DC arc furnace, granulation, leaching, chemical precipitation, selective sulfidizing roasting and product preparations. In this paper, the process stages were described as theoretically and experimentally whereas slag and products were characterized in detail.

Jan 1, 2003

By I-Min Lu

An electric field was applied to a metal-bearing kaolinite specimen to investigate the efficiency of electro-osmosis in removing heavy metals from contaminated soils. The electric field induces a flow of water through the porous medium, called electro-osmosis, which is superimposed on the hydraulic flow. Because the electro-osmotic flow is relatively stronger in smaller pores, it can enhance the displacement of contaminated solution by fluid convection. Furthermore local changes in pH caused by the electrode reactions can affect adsorption equilibria and the distribution of solutes between the solution and the solid surfaces. The electro-osmosis experiments were conducted by applying either a constant current or a constant voltage across 8-cm inside diameter, 25 to 30-cm long specimens of kaolinite clay with graphite electrodes. Samples of the pore fluid and of the clay were analyzed to determine metal content, pH, and conductivity as functions of time and position. Results show that removal of heavy metals from soil can be accomplished effectively by electrokinetic treatment of sufficient duration. Approximately 95% of the lead was removed after 189 days.

Jan 1, 1996

By Joni M. Barnes

A strain of Pseudomonas stutzeri isohted from selenium contaminated surface waters, was found to be effective . in reducing selenate (Se04 2) stoichiometrically to selenite (Se03 2 '), which was further reduced to elementaJ selenium (Se0 ). These reactions were concurrent with the microbial oxidation of lactate. In order to assess quantitatively the amounts of seilenate and selenitein solution, improvements to existing analytical methods (ion exchange chromatography and inductively coupled plasma atomic emission spectrophotometry technique) .were made.

Jan 1, 1991

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Pravas Ranjan Behera

Red mud of Indian origin contains around 55% plus of Fe2O3 and is considered as a hazardous waste for the alumina industry. For production of one tone of alumina employing the Bayer’s Process, around two tones of red mud is generated from three tones of Bauxite. Conventional process of steel making is not devoid of environmental pollution. In the present investigation, efforts have been made to produce steel from red mud by adopting reduction roasting, magnetic separation and hydrogen plasma smelting route. Magnetic fraction, containing enriched iron oxide and minimal content of alumina, is produced following the first two stages which is then subjected to hydrogen plasma smelting process for production of steel. This novel concept follows a green path way for production of steel free from pollution and is termed as green steel. Further, the only by-product that is produced in the process, is water, which is eco-friendly and recyclable.

Jan 1, 2015

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill as an aid in predicting the effect of corrosion on minerals and how this effect relates to downstream processing. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5% of the total grinding media wear in the operations studied.

Jan 1, 1987

By H. Y. Sohn, M. Y. Mohassab-Ahmed

"As part of research to develop a novel flash ironmaking process using reduction of iron ore concentrate by natural gas or hydrogen, sulfur and phosphorus distribution ratios between MgOsaturated slag and iron were determined in the temperature range 1550-1650°C under three different gas atmospheres: H2/H2O, H2/H2O/CO/CO2, and CO/CO2. The distribution coefficients of sulfur (Ls) were 4.0, 2.0, and 0.8, respectively, under these atmospheres. The distribution coefficients of phosphorus (Lp) were, respectively, 8, 17, and 20 under these atmospheres. In the flash process over -25 wt% P and S volatilize during ore concentrate downward flight in the reactor shaft in addition to avoiding coke. Therefore, iron produced by the flash ironmaking process would have much lower sulfur contents than the typical hot metal produced by the BF.IntroductionGiven the issues related to large carbon dioxide emissions and energy consumption in the existing ironmaking technologies, a novel flash ironmaking technology was conceived by Sohn [1-3] at the University of Utah. This technology is the first ironmaking process that will convert iron ore concentrate directly to metallic iron in-flight. This process will produce iron directly from concentrate without requiring pelletization or sintering and avoid the need for coke. In addition, this process concept takes full advantage of the fine particle size of concentrate with a large surface area, which permits rapid reduction by a gas. In this novel ironmaking process, potential reductants and fuels are H2, natural gas, and coal gas. Therefore, an iron-slag bath is expected to be at equilibrium with gas atmospheres of mainly H2/H2O or CO/CO2/H2/H2O, respectively, corresponding to the use of H2 or natural gas/coal gas. Since the effects of an H2O- containing atmosphere on slag properties have not been studied before, it is critical for the development of the novel flash process to determine these effects. In H2-H2O-CO-CO2 gas mixtures under ironmaking conditions, H20 was found to have the most pronounced effect on the slag chemistry [ 4, 5]. In addition, it was found in this laboratory that water in the gas atmosphere affected the distribution of Mn between slag and molten iron [6]. Most previous work used CO/CO2 gas mixture to control oxygen partial pressure (p02) [7, 8]. Others used only inert atmospheres [9], although Kor and Richardson [10] used a mixture of C02/H2 to control p02. For phosphorus, previous research focused on Ar [11], Ar-CO mixture [12], CO [13], CO/CO2 [14] or N2/CO [15]. Therefore, it was necessary to investigate the effect of water vapor content in H2-H2O-CO-CO2 mixtures on the equilibrium distribution of sulfur and phosphorus between CaO-MgOsatSiO2-Al2O3-FeO- MnO (0.2-0.8 wt%)-P2O5 (0.1-0.9 wt%) slag and molten iron as part of the development of the novel flash ironmaking technology."

Jan 1, 2014

By Claudio Toro, Alex Moyano, Jonkion Font, Carlos Caballero, Pedro Morales

"Codelco-Chile in the last decade has carried out industrially-oriented research as an alternative to the traditional batch-type converting process. In a first stage carried out preliminary evaluations in a rearranged Peirce Smith (PS) converter, and then an exploratory test in a “Convertidor Teniente” (Teniente converter, TC) for the Codelco-Chile Continuous Converting Process. However, the validation test for this process in the TC was delayed up to the second quarter of 2007 where the validation studies were done satisfactorily.Thus, the objective of this paper is to present the results of the campaign tests validating the Codelco-Chile Continuous Converting Process in the TC1 of the Codelco Norte smelter.The results of charging the solid or liquid matte or high grade matte (“white metal”) by Garrgun, or by mouth of the 22 m x 5 m TC1 are presented. Some features of the industrially validated process are discussed, and the pilot test results of the matte injection are also presented."

Jan 1, 2009