Search Documents

By Jinsheng Chen

To maintain the stability of longwall tailgate entries, they have to be supported by not only the primary roof support but also the secondary roof support due to the impact of the longwall mining¬induced abutment loads. Depending on the mining condition of a typical coal seam and its distance from the previous panel's gob, the longwall tailgate entry is often reinforced by the secondary roof support in the form of standing supports and/or cable bolts or trusses during longwall retreat, Even though lots of research work has been done to study the behavior of different standing supports in the laboratory. their function and requirements for a typical mining condition are still not fully understood due to lack of field data and correct assumptions about the behavior of the already-bolted entry roof under mining-induced abutment loads. Therefore, the application of the secondary roof support for tailgate entry roof control is still limited to trial and error, which often results in either higher cost for tailgate roof control if the design is too conservative or more production delays due to roof falls in the outby tailgate entry if the design is inadequate. To have a better tailgate roof control with reasonable roof control cost, RAG American Coal, NIOSH, and HeiTech have been conducting a joint research project to monitor actual roof loading, roof deformation, and entry convergence in the tailgate entry of 10 North panel at RAG Emerald mine. The actual roof loading data are used to calibrate and improve the roof control model for longwall tailgate entries, which has been developed by RAG American Coal, and to further reduce the roof control cost for longwall tailgate entries. The authors in this study attempt to discuss the Roof Control Model developed by RAG American Coal. in which some guidelines or important parameters for designing the secondary roof support for longwall tailgate entries are proposed.

Jan 1, 2003

By E. Bane Kroeger

In underground coal mining, there is often a need for supplemental support for mine openings. In the past, one of the most common types of supplemental support was wooden posts that were installed against the roof using opposing wooden wedges. Underground, wood has the tendency to shrink from moisture loss and dislodge if not under load. Another drawback to using wood is the variability in strength between posts. Defects in the wood such as knots can cause weaknesses that often lead to premature failure of supplemental support. Many mines that install large amounts of supplemental support in certain areas of the mine such as bleeder entries in longwall mining have switched to using steel props rather than wood posts or cribbing. The reactions of steel props under loading are well- defined and there is little variability in strength between props. Steel props and can be fabricated so they can be used in a variety of roof heights without modification. Wooden posts often have to be cut to a usable length underground before installation. This adds to the installation time of the wooden posts. Steel props are more compact and can be lighter than their wooden counterparts, depending on the length and carrying capacity. Often times it is desirable to prestress the supplemental support to improve roof stability. This is often problematic and time consuming with some types if supplemental support. With these factors in mind, research was undertaken at Southern Illinois University Carbondale (SIUC) to design a new steel roof prop. Several new clamping designs were developed and prototypes were fabricated and tested in the labs at SIUC in the spring of 2003. The designs were modified and refined and the first full-size prototype roof prop was tested in January 2004. With the success of the full-size prototypes, a cooperative research program was established between SIUC and Excel Mining Systems, Inc. to further develop the new prop. Development went smoothly and the prop has performed as expected. In February 2005, SIUC and Excel entered into an exclusive licensing agreement. The prop design under license, the K-Prop, will be installed using a lightweight portable hydraulic jacking system under design that can be used to prestress the props, applying load to the roof and floor during installation. By varying the installation load, the prestress load can be varied from about 1,000 to 10,000 pounds (4.448 to 44.48 kN) and at the same time, the carrying capacity of the K-Prop can be varied from 10,000 to 100,000 pounds (44.48 to 444.8 kN). The K- Prop is composed of only 3 pieces and laboratory testing has suggested that it can be installed by a pair of workers in less than two minutes. The speed of installation of the K-Prop should significantly reduce the total installed cost for supplemental support and should provide a safer working environment by prestressing the prop, which will add support load to the roof and floor during installation.

Jan 1, 2005

By Z. T. Bieniawski

A major study was performed on determination of long term strength of coal strata directed to the design of coal pillars to ensure their stability beyond the life-time of a mine. Based on field investigations, numerical modeling and reliable data from 12 case histories, three aspects of time effect in the strength of coal strata were studied; (1) strength reduction based on the concept of volumetric strain estimate from in-situ tests, (2) strength reduction in terms of three failure criteria applicable to coal strata: original Hoek-Brown criterion, modified Hoek-Brown criterion, and Generalized criterion, and (3) long-term strength estimation as a function of coal strata quality RMR based on case studies. From these investigations, an integrated approach to long-term pillar stability is proposed, based on numerical modeling and empirical pillar strength formulation. The values of factors of safety for coal pillars are analyzed in terms of probability of failure and practical meaning for mine design purposes.

Jan 1, 1994

By A. Mahyera

BETTER ROOF SUPPORT During the last decade, resin-grouted roof bolts have taken a substantial foothold in the coal mining industry - now accounting for about one-third of all bolts installed annually, due to the improved roof support. However, the high cost, toxicity and flammability of the resin cartridges appear to be a limiting factor in even greater use of such bolts. Terra Tek, Inc. has, over the past few years, been developing a novel roof bolting system to mix/inject a very fast-setting and high strength inorganic cement into bolt holes and install point-anchored or full-column grouted rebars - all automatically and at substantial cost savings. This grouting system utilizes a unique method to mix the grout ?in-the-hole?. It has been integrated with a conventional bolter, retrofitted with an indexing-head mechanism and an on-board pneumatic computer to sequence and Control the drilling, grouting and bolting. Cycle times are the same or better than for a resin system. Following laboratory testing/development, the prototype system has undergone field trials in a Utah coal mine. A description of the bolting system, results of pull-tests in the laboratory and field, and economics and productivity gains with this system in comparison to a conventional resin-cartridge bolting method are presented. The relationship of this technique to improved roof control is also discussed.

Jan 1, 1984

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By Marcel0 Mondring

Transportation and the logistic requirements are set very high for the German coal mining industry. Short transportation resources, crowded quarters, and long transportation distances to destinations are some basic conditions that logistic employees of the mines have to deal with. Therefore, in the context of these processes, human effort and technology are faced with great challenges. There can be a total of 300 transport units, depending on the size of the mine. Every day, they are moved through a nearby 150-km-long transportation network of floor and monorail tracks. Of these transport units, 150 are new, and the other 150 units are split into cross traffic units that are moved only in the underground and return travel units. Beside track-bounded transports, all material transports take place in the shaft. As a result, many involuntary transports and changes in the means of transportation make the daily work more difficult. Typical transports in the shaft include the supply of new materials from above to below, as well as returnable goods from below to above. Cross traffics throughout several levels, which are rather rare, would have to be handled above the shaft. Due to limited shaft capacity, these cross traffics should be avoided when possible. Based on the gas resources in coalmine slopes, track-bounded transports using monorails (powered by diesel or rechargeable means) are preferred. This depends on the road degree, the depth, and track cross section of the shaft/slope. The variety of the material spectrum includes more than 100,000 different types of material.

Jan 1, 2014

By K. F. Unrug

A new testing technique for the determination of the rock strength from portable rock tester is proposed. It is a quick and economical method that can determine the rock strength with reasonable accuracy in different conditions. This method is based on the application of portable rock tester working at the principle of forcing steel ball into the rock surface. The correlation between laboratory measured compressive and/or tensile strength and rack tester reading has been determined in terms of the three-controlling parameters: (1). diameter of indentation &'the testing sample, (2). diameter of indentation-on the reference bar, (3). Brine11 hardness number of reference bar.

Jan 1, 1990

By Jesse Puller, Ken Mills

"This paper describes the Australia, New Zealand Inflatable (ANZI) strain cell, its operation, and recent development for overcoring in exploration boreholes. The ANZI strain cell is an instrument system that uses the overcoring method of stress relief to determine the three-dimensional, in-situ stresses in rock. The instrument has been used successfully for over three decades in numerous underground mining and civil projects, but technical advances over the last decade or so have allowed the system to be deployed in surface exploration boreholes to greater depths than was previously possible. Recent development of a downhole electronic data logger, a wireline-enabled drilling system, and an instrument deployment system has simplified the process of obtaining three-dimensional overcore measurements at depths approaching 1km to a single shift operation.The capability to deploy ANZI strain cells in surface exploration boreholes represents a significant breakthrough for the design of underground mines and underground excavations generally. High-confidence characterisation of the in-situ stresses at the design stage provides the opportunity to design key infrastructure and mining systems to take advantage of the in-situ stress field from the outset before mining begins. Understanding the three-dimensional, in-situ stress field not only provides a measure of the magnitude and direction of loads acting within the rock mass, it also provides insight into the mechanics of all the various processes driving ground deformations, including which geological fault structures are at limiting equilibrium.INTRODUCTIONThe overcoring method of stress relief is one of the most direct methods for determining three-dimensional, in-situ stresses in rock. The Australia, New Zealand Inflatable (ANZI) strain cell combines overcoring with several other techniques to provide determinations of the three-dimensional, in-situ stress field and the properties of the rock and, importantly, provides an indication of how much confidence can be placed in the measurement. This paper describes the advances that have enabled overcoring of the ANZI strain cell in deep surface exploration boreholes and the development of various complementary techniques that build additional confidence in the determination of the in-situ stress."

Jan 1, 2018

By David C. Laurence

in March 1999, the School of Mining Engineering at the University of New South Wales carried out a series of underground trials using " Evermine", a South African developed two-part water based polymer membrane. The aim of the trials was to determine the potential of a spray-on polymer membrane such as Evermine as an alternative to conventional rib support systems The mine selected was Angus Place colliery, reputed to have some of the worst ground conditions of any Australian underground coal mine. Ribs at Angus Place are supported by conventional pattern bolting supplemented by wire mesh. The trials indicate that there is significant potential for the introduction of polymer membranes into the underground coal minim; industry Initial results indicated that ribs that had been sprayed exhibited less displacement and spalling than unsprayed ribs. particularly when subjected to abutment loads from an approaching long-wall Further research will he required to conclusively rate the performance of Evermine in comparison to other products in the market and the long term performance of the product

Jan 1, 2000

By Thomas Rymer

Mathematical modelling of mine subsidence measured at 21 locations in Pennsylvania and northern West Virginia allows for the refinement of current methods of predicting maximum land subsidence associated with longwall coal mining. This new method (RYBAD model) is an extension of that provided by Tandanand and Powell (1984; TP Model). The RYBAD model accomplishes more accurate subsidence predictions (error typically less than 10 percent) for a greater range of mining and geological parameters through the recognition of the following: 1) subsidence increases at a decreasing rate (curvilinear relationship) with greater overburden thickness up to a critical value beyond which subsidence decreases; 2) subsidence is strongly influenced by the stratigraphic proximity of strong rocks to the coal (size of potential caving zone); and 3) subsidence index is related to overburden thickness by a family of curves, each for incremental variations in the effective percentage of strong rock in the overburden.

Jan 1, 1988

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By Archie Richardson

Periodic weighting of longwall supports occurs during retreat ofthe face under certain geologic conditions. Strong stratain the immediate and main roof tend to cantilever over the gob, weighting the supports periodically. The distance between weighting peaks, as well as the intensity ofperiodic weighting, is determined by the suength and thickness of roof members, their location relative to the seam, the frequency of joinling, and characteristics of the gob. In this paper the effects of varying several of these variables ate investigated using block modeling. The models are calibrated against a published case history of periodic weighting in the Pittsburgh Seam. It is concluded that block modeling is a useful tool for correlating measured support pressure histories with expected modes of strata behavior in the roof, with potential for predicting shield behavior in new geologic enviromnents.

Jan 1, 1998

By Mingju Liu

In this research, we measured fractal characteristics of over ten typical outburst areas on different scales and related them to their outburst proneness, in attempts to provide new methods for outburst prediction. It was shown that both faults and folds follow the power law on coal basin scale, mine scale or mining district scale, whichever it is. Fractal dimensions are appropriate indices to describe geological structures quantitatively. Preliminary relationships have been established between outburst proneness and fractal dimension. Comparisons have been made among fractal characteristics and degrees of outburst proneness on all three scales. The results indicate that multi-scale assessment of outburst proneness can be made based on fractal measurements independently or supplemented by other assessment methods.

Jan 1, 2000

By Arthur Miller, Andrew Weakley, Heather E. Lawson

"IntroductionDynamic failure events in an underground coal mine, or “bumps,” are defined as “the sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillars, or the solid block of coal being thrown into an open entry” (Peng, 2008). Reports of disastrous and often fatal dynamic failure events date back over one hundred years in the United States. Mining practices and technologies have significantly evolved over the course of the last century, yet these events continue to occur. The events at Crandall Canyon, Utah (Gates et al., 2007) and Brody No. 1 Mine in West Virginia (Barker and McNeely, 2014) are two recent failure events that resulted in a total of eleven fatalities. These events testify to the fact that dynamic failure remains an imperative safety concern. Furthermore, their continued occurrences indicate that engineering controls have proven inadequate at wholly mitigating the problem.Multiple conditions have been associated with the occurrence of dynamic failure phenomena, including• thick, competent strata that can create a bridging effect, resulting in high abutment stresses (Rice, 1935; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Agapito and Goodrich, 2000; Peng, 2008; Whyatt, 2008; Whyatt and Varley, 2010)• overburden thicknesses greater than 500–700 ft. (Rice, 1935; Peng, 2008)• a strong coal that is resistant to crushing (Rice, 1935; Peng,2008) or that is “uncleated or poorly cleated, strong…sustains high stress and tends to fail suddenly” (Agapito and Goodrich, 2000)• the presence of sandstone channels or rolls that can serve to concentrate stresses (Iannachione and Zelanko, 1995; Agapito and Goodrich, 2000)• fracturing of strong units above or below the coal seam (Whyatt and Varley, 2010)• slip along pre-existing discontinuities (Peperakis, 1958; Whyatt and Varley, 2010)• multiple seam mining interactions (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995; Newman, 2002; Peng, 2008)• mining sequences that can cause anomalously high stress concentrations (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995)"

Jan 1, 2015

By Quanxi Wang

This paper presents a new stability mapping system which tightly integrates structural and geologic mapping with geo- mechanical stress analysis for use in support design and mine plan- ning. The structural and geologic input can include such local characteristics as: rock strength, layer thickness, faults, stream val- ley effects, etc. The geo-mechanical stress inputs can include overburden stress, multiple-seam stresses, abutment stresses, etc. The mapping system utilizes the popular AutoCAD/SurvCADD platform as a foundation for inputting the geologic characteristics, and then integrates the boundary-element program LaModel for determining the geo-mechanical stress influences. Additional func- tionality in the system allows the user to transform each individual geologic or stress factor into an individual rating and then the user can apply various weighting functions to the individual factors to generate an overall stability index map for the mine property. A sample case study is included in the paper to demonstrate the basic concepts, procedures and utility of the stability mapping system.

Jan 1, 2005

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these situations,

Jan 1, 1992

By Axel Preusse

In the Ruhr district, pipelines of public and private infrastructure are made of cast iron, steel, plastics or asbestos cement. Legal framework, technical regulations and normative standards define which pipeline materials may be used for the transmission of which kind of product Thus ground water endangering substances as well as inflammable or explosive products are only permitted to be transported in steel-made pipelines. Ground movements, due to underground mining, are transmitted via the soil to the pipeline and cause extra strain within the steel pipeline (Figure I). In extreme cases durable deformations may occur, characterized by an oval profile or a fold in the pipeline. To avoid or minimize damages, balancing elements are installed into the concerning pipeline, reducing the ground movements which might otherwise cause damages. [ ] The distance between the balancing elements is not arranged by random, but by a calculation method developed in a doctoral thesis [Spielberg, 1999] which represents the actual available standards in science and technology. The calculation method considers all relevant influencing variables with impacts on the movement behaviour of steel pipelines in mining areas, such as technical data of pipeline design (e.g. steel grade, wall thickness, weld seam quality), soil conditions (e.g. friction), laying depths of the pipelines, the operational impacts (working pressure, corrosion) and the mining impacts. As of today, mining has caused no damages to steel pipelines protected by this calculation method.

Jan 1, 2004

By W. J. Guo

Overburden movement as a result of longwall mining can be classified into, in ascending order, caving zone, fractured zone, and bending zone. Operation experience and laboratory research have demonstrated that there are bed separations in the bending zone due to differential movement and rock mechanics properties between adjacent strata. In china several coal mines have injected flyash into bed separations to prevent strata movement and control surface subsidence. This method is very effective because it can reduce surface subsidence by 35-55%. Combining the field survey results and laboratory simulation research, the author has investigated bed separation and its mechanisms and effect of backfilling the bed separation and its mechanisms. Finally backfilling application in three mines are introduced, including grout flow chart, grouting pressure, and radius.

Jan 1, 1994

By Keith A. Heasley

Pillar recovery in deep coal mines with competent roof and floor can concentrate stresses and generate hazardous bumps. Actual calculation of the geologic strain energy released in association with these coal bumps has been rare, although energy release values have been utilized successfully for indicating burst potential in numerous hard- rock mines. This paper advances the current knowledge of energy release calculations as applied to coal bumps through an extensive analysis of an actual bump occurrence. The U.S.B.M, displacement- discontinuity code, MULSIM/NL, is used to produce a numerical model which generates stress, displacements and energy values associated with a pillar retreat section. This model is calibrated with actual field data, and then dissipated energy values from the model are examined as to their suit- ability for indicating bump potential. Ultimately, it is determined that prudent application of dissipated energy calculations can be used as a tool to investigate the coal bump potential of a mining plan or cut sequence.

Jan 1, 1990

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015