Search Documents

By Mike S. Ness, Allan G. Provost

High speed drilling, mucking, and hauling equipment was used in driving approximately 2.16 km(7100 ft) of lower power tunnel in quartz diorite for the Tyee Lake Hydroelectric Project near Wrangell, Alaska. The .91 m(36 in.) guage rail mounted equipment included a Tamrock 2-boom electric/hydraulic drill jumbo, a Haggl and 8HR mucker , and 3 Hagglund 115C shuttle cars. Several other innovative techniques allowed maximum advance rates of up to 17.5 m/day(57ft/day) in the 3 m(10ft) horseshoe section. Average tunnel advance was approximately 11 m(day(35.4 ft/day). The primary difficulties preventing full utilization of the equipment potential were the operators' "learning curve", the need for complete retraining of all personnel in the new methods, and minor sections of faulted ground.

Jan 1, 1983

By Agne Rustan

Most of the mines in Sweden are metal ore mines in hard rock and none of these mines are classed gassy because there is no methane emission. The risk of methane explosions in Swedish mines is therefore very small. Since the 1960?s, in Swedish mines, there has been a change from electric and pneumatic loaders and transport machines to diesel. Today in almost all Swedish underground mines diesels are used. One of the most common complaint from the underground mine- workers is the exhaust gases from the diesel-vehicles. This is a strong motive for attempts to assure a more comfortable environment. Another motive for a better efficiency of ventilation under ground is the increasing cost of energy for fans and for heating the air during winter. For the largest mine in Sweden, the Kiirunavaara Mine, 36% of the energy for ventilation is used for preheating the air during the seven months when the temperature is below zero. The air quantities used for ventilation are large. In table 1 a comparison of the ratio between yearly produced ore and waste rock and installed fresh 'air capacity is shown. [ ]

Jan 1, 1980

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION The majority of ground water flow models have been developed for large computer systems. Most of these operate under a batch mode of operation, that is, the data are input with a deck of punched cards. The advent of micro- and minicomputers over the last few years opens the possibility of adapting many of these large flow programs to the smaller computers. In general, this adaptation will require more computer time to run the program, but in many cases if the small computer is in-house, the overall cost may be less than that required for a large computer. There are also a number of peripheral devices that can be used to make the data input much easier. As an example, the use of a digitizer with a finite element or finite difference mesh reduces the data input time considerably; the use of a graphics terminal for display of the mesh immediately after it is developed shows immediately whether there are errors in the location of node points. DEVELOPMENT OF AN INTERACTIVE SYSTEM The finite element program, UNSAT2, has been used over the past several years by the authors for several ground water flow problems (Bloomsburg, 1977; Bloomsburg and Wells, 1978; Zahl and Bloomsburg, 1980). In the past these programs have been run on an IBM 370/ 145 computer under the batch mode of operation. One difficulty that has been encountered has been in determining the length of time step that must be specified for operation of the program. The problem is that if the time steps are too large, the program becomes un- stable and operation ceases. If this happens in the middle of the problem, the only alternative is to reduce the length of time step and repeat the entire run. This problem has been alleviated in other pro- grams by using a subroutine that determines the time step automatically. If the solution becomes unstable, the time step is reduced automatically and that portion of the solution is repeated. With an interactive system this can be done by storing the output pressures and restarting the program with the new output pressures. Under the batch mode of operation, there is an option in UNSAT2 that allows restarting of the program from the last point of solution, but this must be specified when originally starting the program. The interactive computer system that we use currently consists of a PDP 1 1 /23 with hard disk drive, CRT terminal, plotter, graphics terminal, digitizer, and printer. The computer has 256 K bytes of core storage and the hard disk drive will accept a 5.2 M byte disk. To run a large program on a computer such as this, some overlaying must occur; that is, subroutines are stored on disk and put into core storage only when they are actually needed for running the program. UNSAT2 required very few changes to run on this computer but some changes were necessary to take advantage of the interactive capabilities of the system. One of these changes consists of the development of a program called DBUILD to build the data file for running the program. This program calls for each piece of data by prompt statement and gives instructions for using the digitizer. The data are then entered in completely unformated form. The node points must be entered in order and the coordinates are determined automatically by the digitizer. The pressure readings or initial conditions on each node point are entered through the terminal. All element information also is entered through the terminal. After DBUILD is run the mesh may be displayed immediately on the graphics scope whereupon any error in node point

Jan 1, 1986

By Brian Flintoff

SCOTT COULTER: Our second speaker today is Brian Flintoff. Brian graduated from the University of Alberta in 1973 with a master's of science degree and worked as a project metallurgist at Brenda Mines until 1977. He returned to the University of Alberta in late 1977 to work on his Ph.D. and later joined the faculty of engineering in 1980, leaving in 1988 to rejoin Brenda in the newly formed process technology division. In 1998 he left Svedala-Brenda to take a position with Simons International's newly formed enterprise development services group. His topic today is "People: Reduce, Reuse, and Recycle." INTRODUCTION BRIAN FLINTOFF: Historically, the mining industry has relied on the people within a corporation to get things done. The culture of most companies was one of a slow but sure development of people, processes, equipment, and technology. Many of the larger companies supported in-house engineering and research organizations. However, the metal market pressures of the 1980s and the emergence of the global economy in the late '80s and early '90s put enormous financial pressures on the industry. As the old adage says, "necessity is the mother of invention," and the mining industry, like many others, has undergone a transformation. A cornerstone element of the transformation was the downsizing (or right-sizing) that was calculated to "trim the fat" from the capital and operating budgets. The goal was and is to find the highest sustainable operating profit.' While I'm sure one can find examples of losers (e.g., those who can be classified as suffering from corporate anorexia or institutional Alzheimer's) in such business reengineering efforts, there is little doubt that, on the whole, the transformation has been successful. The reality that now faces mill management is "How to do more with less?" At the risk of oversimplifying, one can look at this on two levels:

Jan 1, 1998

By Jorgen Elbrond, Xiaoli Tang

In this paper we apply continuous-time option pricing theory (Dixit 8 Pindyck 1994) to show how to obtain an optimal investment rule for a mining project which requires sequential in- vestments. The application per se is to some extent very simple. The main purpose of the paper, however, is to draw the attention of mining people to how the option pricing theory may be used to capital investment decisions. This topic in economics is quite new but is attracting a lot of attention.

Jan 1, 1996

By William J. Francart, Edward J. Miller

The utilization of computer based monitoring systems for fire detection in underground coal mines has grown significantly in the past seven years. In 1984, an annual MSHA survey identified a total of 38 systems being used in U.S. underground coal mines, while a 1990 survey indicated the number has risen to 112. The applications for mine monitoring have also changed according to the annual surveys. From April 24 to June 21, 1990, investigations were conducted by personnel of the Ventilation Division, Pittsburgh Health Technology Center, in cooperation with Coal Mine Safety and Health, concerning the installation and operation of Atmospheric Monitoring Systems in underground coal mines. These investigations were conducted to gather information concerning the ability of the AMS to detect fires and heatings, false and nuisance alarm frequencies, information related to system maintenance, and information related to employee training on system operations. This paper addresses current applications of the systems, fire and heating identification rates, application of systems in dieselized coal mines, system maintenance, and employee training requirements. While deficiencies were identified in some applications, results of the studies and survey indicate the use of atmospheric monitoring systems can be effective in identifying mine fires and heatings.

Jan 1, 1991

By B. A. Barnum

The Chino mine is an open pit copper mine located in southwestern New Mexico, at an elevation of 1890 m (6200 feet) above sea level, approximately 117 km (70 miles) north of the Mexican border. It is owned by Chino Mines Co., a Phelps Dodge Corporation-Mitsubishi Minerals partnership, and is operated by Phelps Dodge Corporation. As part of an effort to maximize production and minimize costs, a computerized truck dispatching system was approved for purchase and installation at the Chino mine in March. 1984. Modular Mining Systems, Inc. was commissioned to install their system, trade named DISPATCH. The system installation was completed and operation began in July, 1985. Installation and operation of the system has presented some interesting challenges and problems, which have been overcome, resulting in increased productivity for the haulage truck and shovel fleets.

Jan 1, 1987

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By A. C. Noble, D. E. Ranta

Orebodies with intricate three-dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer-assisted methods. The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist's interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral deposits.

Jan 1, 1992

By R. L. Kloberdanz

Compania Minera Disputada de las Condes S.A. (Disputada) is proactively implementing closure and reclamation planning activities at its mining and beneficiation facilities (mining facilities) in Chile where regulations governing mine reclamation are not yet fully in place. These activities are being implemented to improve currently employed measures to protect human health and the environment and to enhance reclamation and facilitate future closure with regard to these areas when mining is completed. As part of this process, Disputada, with the assistance of Shepherd Miller, Inc., developed recommendations and guidelines for future closure and reclamation of the Disputada sites. These recommendations and guidance incorporate planning and operational and post-operational design considerations and practices, and standards used by the mining industry and regulatory agencies around the world. The criteria presented in the guidance are based on achieving conditions that will be suitable for the anticipated post-mining land use. This paper discusses the process and approach taken, and the results.

Jan 1, 1999

In a world dependent in part on the consumption of depletable natural resources, development of new areas of mineralization is a necessity for replacing those reserves. Exploration, which is the initial task of replacement, is an information-gathering process which supplies input for management decisions on mine development. If the demand for resources is the driving force of exploration, then the scientific basis for its pursuance is the hypothesis of anomalous mineralization in a metallogenic province, which is tested by measuring physical characteristics of natural phenomenon. The resulting data are reduced, analyzed, and interpreted to locate expressions or responses associated with possible ore bodies. The process is, in fact, repeated in ever increasing measurement detail to increase the accuracy and precision of information for decision making. Exploration ceases when management makes the decision to develop a mineralized area, to hold a property for more favorable market conditions, or to drop a property because it is not economically viable.

Jan 1, 1979

By M. A. Candia

Stability analyses were performed on the La Libertad, Nicaragua existing tailings embankment in order to determine the conditions for the minimum buttressing required for stability of the dam as a short term measure. Two critical sections, shown in Figure 1, were investigated under static, drained and undrained conditions for existing and modified geometries. The existing geometries reflect the "as built" topography of the dam, and the modified geometries reflect the implementation of a toe berm to buttress the slope. For these geometries drained and undrained conditions as well as different elevations of the toe berm were evaluated against a factor of safety.

Jan 1, 1996

By Hilal Soydan, H. Sebnem Düzgün, Jurgen Brune

In this study, with the primary goal of capturing ongoing digital transformation and automation impacts on the mining industry and its workforce, we conduct several interviews with mining industry experts in the United States and analyze our survey reports qualitatively and quantitatively through exploratory analysis. After the interpretation of the insights of industry experts, we proceed to generate a personalized and customized data analysis through a novel metric based on skills, knowledge, competencies and occupational requirements, which quantifies the job similarities for occupations in the mining industry based on the publicly available database of the U.S. Department of Labor. We use text analytics to tokenize and classify the interviews to capture a better understanding of major response categories. The temporal analysis shows that the critical competency needs in the data science and autonomy category increases from 28 percent in current demands to 43 percent. In defining our metric, we also calculate Kullback–Leibler (KL) divergence for each job profile that enables determining whether and to what extent that job is transitionary in our test set based on the mean, standard deviation and kurtosis of each job of interest. Our analysis reveals that the in-group job transitions are significantly easier than the between-group transitions, proving our initial assumptions and common sense. The generated heat maps provide the opportunity to present the gap between the current job and desired job profiles that provide feasible career change options, among others, offering individualized career paths for job seekers and promoting potential job transitions. Through the collection of industry-specific individual employee data, the AI system is envisaged to continue to learn as end users engage with the system, thus creating a central data hub specifically for the future workforce in the mining industry. Although the study has limitations on generalizability for qualitative assessments, it presents itself as a valuable application of how qualitative and quantitative approaches could be of value for future worker training in the mining sector.

Feb 1, 2025

By M. G. Ayat

Although other methods of mineral concentration have been developed over the years, gravity separation remains one of the most efficient and economical for cleaning coal. The concentrating table and the spiral separator are popular devices used for the separation of minerals by exploiting the differences in specific gravities of the product material and the gangue. While the former device has been servicing the coal industry for over 75 years, the latter seems to have not been employed extensively for coal cleaning purposes in this country. As far as coal preparation is concerned, both separatory devices seem to be most efficient for intermediate to fine size fractions. As it stands there exists a great deal of confusion amongst preparation engineers and plant managers as to whether spirals can have a place in the coal industry. If so, whether their come back is the beginning of the end for concentrating tables, or can they be employed along with concentrating tables to contribute toward more efficient cleaning processes resulting in an improvement in the overall economics of the coal preparation industry. This paper examines the efficiency of both systems for coal processing operations as well as the basic principles, operational variables, economics, advantages and disadvantages associated with each unit operation. Attempts have been made to draw conclusions and make recommendations as to which system would be more beneficial for coals of known characteristics.

Jan 1, 1986

By M. Misra

The interaction of xanthate with SO2 in the flotation of sphalerite and chalcopy.ite is discussed. 'The SO depression of sphaledte is due to the decomposition reaction of xanthate by SO2 The decomposition reaction is dependent on the cole ratios of xanthate/SO2, oxygen concentration and pH. Xanthate adsorbs at a faster rate by chalcopyrite than sphalerite. The faster rate of xanthate adsorption by chalcopyrite and the specific action of S02 on the surface of chalcopy.ite facilitate the selective separation of chalcopyrite from sphaledte.

Jan 1, 1989

By C. A. Fleming, K. W. Sarbutt, P. K. MacPhail

The SART process has been developed for Teck to treat bar­ren solution from the cyanidation/CIP process that has been developed for the Lobo-Marte project in Chile. The objective of the process is to recover cyanide in a form that is suitable for recycling to the leaching part of the process. The Marte and Lobo ore bodies require a dosage rate of about 2 kg/t NaCN, of which only 0.5 kg/t is truly consumed (as thiocyanate, cyanate and ferrocyanide species). The remaining -1.5 kg/t is present as cop­per cyanide (-1 kg/t) and free cyanide (-0.5 kg/t), and is poten­tially recoverable and recyclable. SART is an acronym that describes the unit operations in this cyanide recovery process; namely, .. Sulphidization .. Acidification .. Recycling of precipitate " Thickening of precipitate The basic chemistry has been applied previously, and has also been the subject of two patents (American Cyanamid Company, 1965, Potter et al., 1986). The process involves the conversion of all free and WAD cyanide in solution to hydrocyanic acid by acidification of the tailings solution to pH :s,4, and the conversion of all copper in solution to cuprous sulphide (synthetic chal­cocite) by the addition of a sulphide salt:

Jan 1, 1998

By James J. Scott

In the fall of 1976 the author started test work with Friction Rock Stabilizers in uranium mines of the West, principally in the Ambrosia Lake and Churchrock districts of New Mexico. Tests were also conducted in other uranium mines in the Rocky Mountains area. These mines are plagues with problems in ground control due to the weak formations in which mineralization occurs, mudstones, siltstones, weak sand, etc. For this reason, it is extremely difficult to obtain good anchorage for long periods of time with conventional mechanical roof bolts. Resin bolts give good anchorage but are expensive and, because of hole erosion and difficulties in installation due to inadequate equipment for mixing the resin and placing the rebar, they are not widely used. Field testing was also carried out in trona, limestones and hard and soft shale formations. The mechanism of the Friction Rock Stabi1izer support is discussed and pull test data presented for various rock types.

Jan 1, 1977

By H. R. Manouchehri

The responses of calcite, feldspar, and quartz minerals In a laboratory free fall electrostatic separator, before and after tribocharging with stainless steel, PVC, and copper plates, have been investigated. The effect of H3BO3 and BaCl2 chemicals pre-treatment on the electrical properties of the minerals is examined. The changes in the electrical properties are discussed with the determined charge, dielectric constant, and electrical conductivity of the mineral samples. Electrical properties of the minerals and their responses to the electrical field during separation, after tribocharging and chemical pre-treatment, are explored for the need to characterize the electrical behaviour of the minerals.

Jan 1, 1998

By M. G. Karfakis

Grouting has been used in underground mining for more than twenty years. Chemical grouting is often used as a remedial measure when the implemented ground control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. Utilization of the polyurethane grout currently being used is restricted by its limited range of physical and mechanical properties that restrict its utilization. To overcome some of the drawbacks of polyurethane, research has been conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as StrataGrip, provides a number of features, including variable gel times and much reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted. Assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research have defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1997

By Y. Ooishi, Y. Matsumoto, T. Arai, H. Ohta

The multi-circular face shield (MFS) is a new type of tunnelling machine for construction of the special cross section and has been put to practical use in 1988. The MF shield has two circular faces partially overlapped in a single shield machine and can construct the cross section shaped like glasses for the double track railway. And it is possible to equip two or more cicular faces horizontally or vertically, if necessary. During the development of the MF shield the experiments have been carried out for the purpose of estimating the excavatability and the face stability of the MF shield. As a result it was confirmed that the both types of MF shield (one with double faces aligned horizontally and the other with double faces aligned vertically) has higher performance in the face stability and lower value in the cutter torque and the total thrust than the conventional circular shield.

Jan 1, 1991