Search Documents

By H. F. Ghezzi

The indirect method of drying coal fines is applied to filter cakes which ordinarily contain 22 to 30% moisture and are not readily transportable. The "Thermal Dryer", which operates on the mass transfer principle, has found wide use in coal preparation plants. The thermal dryer is penalized in operation by the necessity of adding coarse coal to the wet fines before entering the dryer body in order to produce a permeable bed, and thus enable hot gases to uniformly contact the wet mass. The ratio of coarse coal to fines varies from 2:1 to as much as 4:1, depending on the average particle size, moisture, and ash content of the fines.

Jan 1, 1985

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid leach uranium solution and a strong-base, ion-exchange resin together with the subsequent elution with an acidified sodium chloride solution was studied. The effects of the number of sections, section heights, amount of resin withdrawal, and solution flow rates were investigated. Also examined were the kinetic and equilibrium relationships for the absorption step. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1975

By T. Foster

The continuous operation of decanters in the mining industry relies heavily on the use of synthetic flocculants. Today, as plants seek to lower production costs by increasing throughput it is necessary to obtain optimum performance from the flocculant. Factors affecting such optimization include charge and molecular weight selection, and efficiency of mixing the highly viscous polymer solution with the feed slurry. Beyond maximizing dilution of the solution, the last factor is often ignored. This paper describes a series of calculations, based on fundamental transport theories, that have been used to describe flow conditions within decanter feed wells and to help select flocculant addition points. Examples are shown for the case of hydroxamated polyacrylamide flocculants in the Bayer Process, where proper selection of the addition points can result in lower flocculant dosage and better control of the decanters.

Jan 1, 1996

By David E. Thompson, Daniel J. Dobbels

INTRODUCTION The planning process for projects requiring construction of tunnels in urban environments can be highly complex and involves interaction with professionals of many disciplines. Typically the initial step in the planning process is to establish basic design criteria for the tunnel or tunnel system consistent with its intended purpose. Such criteria might include acceptable tunnel geometry, minimum and maximum slope or other associated criteria. Ideally, once the basic criteria have been established, the next step in the process might include establishing technically feasible horizontal and vertical alignment and shaft siting alternatives and developing "ball park" construction and operational cost estimates for the alternatives. Comparisons can then be made regarding the relative technical and economic merits of the alternatives and the most favorable alignment(s) are selected for further study or preliminary design. Typically the last and perhaps the most important task that is conducted during the planning stage includes identifying issues and potential problems to be addressed during the design and construction stages of the project. Many issues warrant consideration during the planning phase of a tunneling project. For the purposes of this paper, these issues can be divided into two broad categories: technical and non-technical. Important technical issues include, among others, general design criteria, geotechnical and geoenvironmental issues, and constructibility issues. Important non-technical issues include, among others, right-of-way and easement related considerations, project scheduling constraints, both short and long term environmental impacts and overall cost/benefit aspects of the project. With respect to influence on the planning process, these two groups of issues often cannot be separated completely. For urban tunneling projects, however, it is most often the case that the non-technical

Jan 1, 1991

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

By Niles E. Grosvenor

Several methods have been proposed for determining the tensile strength of rock. These have been tried out over the past several years, but the results have been erratic and of doubtful value. The tensile strength of rock is its weakest property, and this property apparently enters into all failure phenomena whether underground or on the slope of an open pit. Therefore, it is essential that detailed quantitative information is known about the tensile strength of rock if the design engineer is going to select the proper pit&apos; slope, pit orientation, or orientation of underground workings so as to give the most economical and safest mining condition. This quantitative information may be used to orient the pit in such a manner as to allow steep slopes along two sides. This information may possibly be used to orient the direction of either underground workings or open pits so as to decrease powder consumption and to increase blasting efficiency. Hence it is of prime importance that a method of determining accurately the tensile strength of rocks be developed.

Jan 1, 1960

By Bruce H. Mason

The exploration for a commercially acceptable deposit of limestone is consid¬ered by many to be a relatively easy task; however, trying to locate a zone of high calcium limestone of economic thickness within a formation, which outcrops only in a narrow band varying in width from a quarter mile to ten miles, adds considerably to the normal problems experienced during an exploration program. The existence of varying glacial and karst features in the outcrop area intensified the problems encountered and complicated the interpretation of the economic value of the deposit. This paper highlights a recently completed five year exploration program during which approximately 3,900 acres of ground in seven civil townships were evaluated as potential sources of high-calcium limestone. Details are given with respect to the final site chosen and the methods used in determining the suitability of the site. This site exhibited many karat features and several methods were utilized to determine the effect of these features on the gross characteristics of the deposit. Aerial photography for both mapping and interpretation were utilized. Black and white panchromatic photography, black and white infrared and color infrared photography were flown. Resistivity, diamond core drilling and close-interval angering were used to supplement the information obtained from the aerial photography.

Jan 1, 1974

By H. Burton

"The selection of the ultimate pit shell has a major impact on the overall value of a mining project. The size and shape of this pit drives the selection of pushbacks, equipment, and project strategy, each of which are significant in their own right. Optimization of the ultimate pit shape is typically done using the Lerchs-Grossman algorithm with inputs of production costs, commodity prices, and pit slope constraints. This method ensures that every tonne mined is profitable but does not take into consideration the timing of material release. This timing is essential when calculating the Net Present Value (NPV) of the project, which is one of the most popular metrics for valuing deposits. Often, when the mining schedule and discounting are applied, material that was considered profitable before discounting becomes sterilized. The objective of this paper is to show the methodology for improving ultimate pit selection by considering the production schedule. Application of this technique will generally produce a smaller and higher-value pit than using the Lerchs-Grossman algorithm alone. INTRODUCTION The Lerchs-Grossman Algorithm was developed in the 1960s and exists to produce a mathematically optimum shape for open pit mines (1). This algorithm is now an industry leading technique for producing the theoretical optimum shape for open pits and is used in many popular pit optimization and strategic planning software packages, such as GEOVIA’s Whittle. The Lerchs-Grossman (LG) Algorithm is based on graph theory and optimizes on the assumption of non-discounted cash flows. This produces a mathematically optimum shape, but does not consider the timing with which the material will be removed from the ground. This is an important consideration, given that one of the most popular metrics for evaluating mining projects is Net Present Value (NPV) (2), which relies on the timing of cash flows as a major differentiator between options. This paper will discuss issues inherent in the use of ultimate pit selection based on undiscounted economic factors and illustrate a simple technique in Whittle, a leading software package, which can be used to improve the NPV of projects."

Jan 1, 2015

The impact of smoothing on the definition of ore and waste boundaries using linear estimation and conditional simulation methods is discussed. The nature of transfer functions is examined including their ability to incorporate categorical data (e.g. a dominant lithology code). An Ore Block Optimization (OBO) transfer function is presented that provides a clear guide for the mining geologist. Advantages are seen in defining stockpile cut-off grades and meeting production targets such as maximizing head grade, maximizing ore tonnes or minimizing ore loss or dilution. Each of these scenarios impacts on mine profitability and grade control.

Jan 1, 1999

By William R. Beloff, Franklin M. Grynkewicz, Puza

Construction of the MBTA Red Line Extension through Somerville, MA, called for driving twin tube tunnels through a zone of approximately 83m (273 ft) with mixed face conditions. While the majority of the tunnels were driven through competent hard rock using drill and blast techniques, the mixed face zone was advanced using floating crown bars for primary support. The overburden consisted of medium clay, underlain by water bearing glacial till, over a sloping bedrock surface. Due to the unusual nature of the construction techniques, a program was undertaken by the Contractor to monitor ground movement and stresses in the temporary steel supports. This paper presents a description of the instrumentation employed, as well as the measured ground movements and support stresses. Additionally, the tunneling techniques are briefly presented and commented upon. PROJECT DESCRIPTION The Davis Square to Porter Square Tunnel Contract is part of the Massachusetts Bay Transportation Authorities (MBTA) Red Line Extension from Harvard Square in Cambridge to the Alewife Brook Parkway via Somerville. The 5.1km (17,000 ft) Red Line Extension consists of four major new stations, three of which will be interlinked via tunnel construction, and the remaining station will be the last link of an open cut portion, and a terminal point for this phase of the extension. This 866m (2,790 ft) portion began at Porter Square in Cambridge and rose at a 4% slope through Somerville, terminating at the new Davis Square Station. Twin tube tunnels were constructed through 763m (2,517 ft) of rock and 83m (273 ft) of mixed face conditions at the Davis Square end. Figure 1 presents a plan view of the entire contract.

Jan 1, 1981

By S. Davis

It has been accepted almost as dogma that sampling contributes most of the error to fluctuations in gold fire assays. Differences in assay results on pulp material from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" or relatively coarse gold particles. It is true that if coarse gold particles are present they contribute to substantial sampling fluctuations, but while the process of sampling is probably the major source, the analytical process cannot -be completely ignored as a possible contributor to erratic assay results. In order to maintain a stable assay process, the analytic part of the system must be kept in control as well as the sampling and preparation part. One way of monitoring the performance of the analytic system is to systematically assay standard material whose sampling characteristics are carefully controlled. Gold assay standards are not prepared nor can they be prepared to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for preparation (which includes both the processes of comminution and splitting) followed by fire assay, to make inferences only about the fire assay process. Because most gold ores are very heterogeneous, sampling errors would in most cases completely mask the contribution of the analytical errors. Assay standard material is prepared only to assess the accuracy and variability in the fire assay process.

Jan 1, 1995

By Xinchun Li, Youdi Zhang

AI is one of the computing methods, artificial intelligence performs its calculation by simulating the intelligent behavior of human beings. It is regarded as one of the most important scientific achievements in the 20th century, A1 has been developed rapidly in recent years with the development of the computer technique .The application of AI in the mineral industry has also obtained rapid progress sine AI has been used in early 1980&apos;s, such as evaluation of resource, underground mining, surface mining and mine safety etc. It has played an important role for increasing mining efficiency, improving mining management and ensuring the safety of the miner. An integrated A1 system has been developed for coalmines environment management in this paper.

Jan 1, 2002

By Roberto Zaragoza

Historically, the control of flotation operations has been viewed by many as an art. Only recently has process measurement and control come to be viewed not as an ?art? but as a very complex and productive science. In recent years, process control applications to flotation plants have been established and already some gains have been reported for several industrial operations using individual stabilizing control loops including level, pulp flow, pulp density, reagent addition rate and pH (Paakinen, 1979; Hales, 1985). The use of process control computers combined with on-line x-ray florescence (XRF) in industrial flotation circuits has made the application of more sophisticated control techniques feasible in the mineral recovery process. In spite of the availability of reliable instrumentation in modern flotation plants, satisfactory control strategies are difficult to develop and implement. Extremely important factors such as changes in ore type, liberation characteristics, flotability, degree of oxidation on particle surfaces, and specific gravity constitute unmeasured disturbances to the process. Most current control systems cannot adapt specifically to such disturbances.

Jan 1, 1987

By S. Yuan

A large-scale work scheduling algorithm has been developed in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. This study basically concerned the formulation of a reliable mathematical programming model to handle the problem, the achievement of an efficient solution of the model, and the implementation of the algorithm to the worker assignment problems of a large underground coal mine. The results showed that the work scheduling algorithm can make optimal assignments efficiently. It is believed it has potential significance in improving manpower utilization and can offer great help to coal mine managers in making efficient manpower allocations.

Jan 1, 1994

By A. B. Mayer

A generic task summary for design and implementation of hydrogeology programs at open-pit mine operations is presented as a guideline for management. Rigorous assessment of the local and regional hydrogeologic system is necessary to plan dewatering activities and to address environmental concerns. Dewatering activities include calculation of dewatering requirements, design of dewatering systems and evaluation of dewatering-water disposal areas. Environmental concerns include calculation of dewatering and water-disposal impacts, mitigation of soil and ground-water contamination and acquisition of water rights. Three-dimensional numerical models are commonly used to support these analyses. A thoroughly developed hydrogeology program provides an interactive basis for dewatering feasibility decisions and for support of environmental permits and regulatory compliance.

Jan 1, 1993

By Donn W. Leva

In North America, pipelines move more material than any other form of transportation. 1 Pipelines have been used principally for the transportation of liquids and gases; however, slurry pipelines have made notable gains in recent years enabling solid materials to be moved efficiently by pipelines. The obvious advantages of pipe-lines --low maintenance, low operating costs, minimal impact on the environment, greater land use, low labor intensity, safety and high operating factor --have stimulated researchers in England, West Germany, Japan, USSR and the USA during the past ten years to develop pneumatic capsule pipelines for the movement of bulk materials in large quantities. As a result of this work, pneumatic capsule pipelines are now available for the movement of dense bulk materials. Through these pneumatic capsule pipelines, material is moved in wheeled capsules which are pushed through the pipeline by flowing air. In this paper, a capsule pipeline system developed by the Georgia Institute of Technology and Tubexpress Systems, Inc. of Houston, Texas is discussed. The Tubexpress System Major Components The pipe used for a Tubexpress capsule system is standard thin wall welded steel pipe. Since pressures in the system generally do not exceed one atmosphere, the controlling design criteria for wall thickness of the pipeline is pressure from the overburden of the backfill if the line is buried or the structural requirements for supporting itself and the load if it is suspended or supported on piers. The air pumping system for Tubexpress is a combination of

Jan 1, 1977

By S. C. Suboleski

Forecasts indicate that the acid rain bill currently before Congress is likely to cause an increase in demand of 30 to 40 million tons per year of compliance quality coal from Central Appalachia. This represents a doubling of this segment of the coal business. This paper will examine how this doubling can be met, what the likely implications for pricing are, the major uncertainties associated with these predictions, and the likely outcomes of the growth in compliance coal. Finally, some implications for fuel planners will be discussed.

Jan 1, 1993

By S. K. Kawatra, S. K. Valluri, S. J. Root

Common carbon dioxide capturing reagents, such as amines and sodium hydroxide, are expensive, toxic, and energy intensive to regenerate. We have added frothers to a sodium carbonate solution in order to increase the surface area available for CO2 transport within the packed bed of a counter current scrubbing column. Addition of frothers has improved the performance of sodium carbonate scrubbing solutions to be on par with sodium hydroxide scrubbing solutions. This novel enhancement of a relatively inexpensive CO2 capture-regeneration cycle shows potential to allow plants to turn a profit by sequestering a waste product. These results are discussed in detail in the following manuscript. INTRODUCTION The combustion of fossil fuels converts chemical energy to thermal energy. CO2 is produced as a byproduct of the reaction. 80% of the world’s electricity is produced by using this thermal energy to power a generator, accounting for 40% of global carbon dioxide emissions. In an effort to stabilize the rising atmospheric CO2 levels, researchers are investigating the application of carbon capture and storage (CCS) systems in power plants. [1] Efforts to capture CO2 at some power plants have been successful, but the cost of installing and operating the required equipment is high. As such, very few power plants have CCS systems. If CO2 can be captured and processed into a product that can be sold at a profit, installing CCS systems in power plants will be a very attractive business decision. In order for the sale of captured CO2 to become a profitable venture, the cost of capturing the CO2 from a flue gas must be reduced. BACKGROUND The most common method for separating CO2 from a flue gas is by passing it through a counter-current packed bed scrubbing column. The flue gas enters the bottom of a column while a solution of a chemical with properties advantageous to the absorption of CO2 is pumped to the top. The fluids interact in a packed bed, where the CO2 is transported from the gas to the liquid. CO2 is an acid gas, so it is common for the scrubbing solution to be alkaline in nature in order to neutralize the carbonic acid that is formed when it is dissolves into water. The exhaust exits the top of the column free of carbon dioxide, which exits the column in the scrubbing solution, reacting or complexing with the absorbent. Figure 1 is a schematic drawing of a CO2 scrubbing column. It shows the molar flowrates and compositions of the gas and liquid at the bottom [1], the top [2], and an arbitrary height in the column [Z]. [2,15] L is the molar flowrate of liquid at any point in in the column. G is the molar flowrate of gas at any point in the column. Since the CO2 is transported from the gas to the liquid, L and G are variable with respect to height. To simplify calculations, the CO2 free molar flowrates Ls and Gs are often used. X is the fraction moles of aqueous CO2 per mole of CO2 free liquid. Y is the fraction moles of gaseous CO2 per mole of CO2 free gas. Figure 2 is a composition diagram of the scrubbing column depicted in figure 1.

Jan 1, 2019

By Sharon G. Roness

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their: coal. Sulfur was the major concern. Btu content and sodium limited the market for some plants. The PRB market has now extended to plants that are converting from other coals because of the Clean Air Act. These new customers are more sensitive to constituents that affect boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to improve cost controls. Kerr-McGee Coal&apos;s Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998

By John R. Marks

In April 1990, the Homestake Gold Mine embarked on a five year, $US 23 million underground drifting and drilling program to explore promising ore targets north of the current mine. This paper describes the ventilation and air-conditioning system that was installed for the 4m x 4m x 5.2 km (ultimately) drift, which is being driven at about 8m per day in 48OC (118.5 F) crystalline rock. Design parameters are described first. Differences in South African, Canadian and U.S. drift ventilation and civil tunneling techniques proved interesting. Details are then given on equipment selection, installation and performance. Costs are included. Special note is made of safety considerations for a long, dead-end drift.

Jan 1, 1991