Search Documents

By Qingxia Liu, Chen Tingzhong, Chen Jin, Yang Xiaosheng

It is common problem (Huan Xinsheng, etc.,l992)for most iron ore concentrators in China that the concentration of thickened tailings is lower than the need for economical transportation. To solve the problem, two methods of improving the properties of the existing thickeners and using separate thickening technique have been applied in three iron ore concentrators. However, in the case of the Daye iron concentrator a new technique of cyclone-flocculated sedimentation was developed by present authors and verified by experiments. The new technique employs efficient hydrocydone designed by authors in conjunction with a low cost flocculant named KLP.

Jan 1, 1995

By Dennis K. Mortensen

Improvements in metallurgical performance are continually being made in the attempt to achieve the metallurgist's goal of maximum concentration, minimal loss of recovery and at costs that maximize profit margins. Innovative technological advances provide a means for the metallurgist to more thoroughly understand the mechanisms of separation and foster new ideas from old. Problems associated with the implementation of new technology can be overcome effectively if the metallurgist thoroughly understands the metallurgical systems with which he is working.

Jan 1, 1991

By John Durkin

A system based on seismic techniques has been developed to detect and locate men trapped underground following a mine disaster. Both theoretical and field studies have been used to generate models to predict the performance of the system. For a strong source, it is almost certain that the miner's signal will be detected if the geophone array can be positioned over a likely area of entrapment. After signal processing, it is highly likely that the location of the miner can be determined within an accuracy of 100 ft (30.5 m). The system is presently operational in a state of readiness in the event of a mine disaster.

Jan 1, 1980

By Joseph A. Dos Santos

Developed in 1983, high angle conveyors - HAC®s are proven versatile systems for elevating materials continuously from a lower to an upper level. Such systems may also be used to lower materials continuously. HAC®s have found commer­cial application in widely varying materials (including coal, refuse, coarse ores [-250 mm], hot clinker, municipal sludge, wood chips, gypsum, slag, excavated earth, various grains and RDF), at widely varying throughput rates from 0.27 to 4250 t/h. The conveying profiles have varied widely and elevating heights range from 3.66 m to 175 m. HAC®s have found application in coal, copper and iron mining, and preparation, in municipal waste treatment, rapid transit projects, pulp and paper mills, cement plants and in gold mining. While noting a wide variety of applications in general, the present writing focuses on Newmont Gold's HAC®, near Carlin, Nevada, which elevates very coarse gold ore to the screening plant. Additionally, upcoming HAC® applications in gold mining are discussed and a proposed multi-flight vertical HAC® system from a deep underground mine is described.

Jan 1, 1996

By Carter Brown, Kate Brown Requist, Eric Lutz, Moe Momayez, Athira Satheesh

New mining health and safety training modalities are becoming increasingly prevalent in the underground mining industry. Various digital training tools have been developed over the past several years, but the extent of their use remains unclear. Advances in gamified training by way of computerbased video games and virtual reality (VR) have opened a new avenue for mine rescue and self-escape training, but these methods have not been widely adopted across the mining industry. Mine rescue and self-escape situations require a mix of in-classroom training as well as live drills, but it is important to assess the extent of and effectiveness of new training modalities. The Mine Rescue and Self-Escape Survey (MRSES) was distributed to underground mining operations to collect perceptions of current training effectiveness as well as willingness to adopt new training methods as a complement to live rescue drills. Responses from the MRSES indicate that adoption of digital training technologies has been slow-going despite an interest in their use. Further, there appears to be no meaningful connection between more frequent escape and rescue training and feelings of emergency preparedness. With relatively little use of already developed digital training tools but an interest in their adoption, it may be time to reassess current emergency preparedness training philosophies.

May 1, 2025

By D. H. Desy

This research was undertaken to establish the lncendivity of aluminum alloys against rusty steel under frictional impact conditions at typical coal mine fan speeds, to determine any differences in incendivity among various aluminum alloys, and to Investigate less incendive materials as substitutes for aluminum alloys. With a specially designed apparatus, three aluminum casting alloys and three constructional steels were tested for incendivity in frictional impact against rusted steel in flammable methane-air mixtures. Although varying in degree, all aluminum alloys investigated exhibited a high ignition probability under the test conditions; none of the steel specimens tested caused any ignitions under the same conditions.

Jan 1, 1973

By M. C. Fuerstenau, J. J. Fitzgerald

Aluminum silicate hydrosol synthesis and characterization are discussed. Plausible polymeric aluminosilicate species are presented together with their effect on electrokinetics of selected minerals and flotation response of various ores. The addition of aluminosilicate hydrosol to porphyry and oxide copper ores and to a tungsten ore resulted in enhanced flotation recoveries ranging from about 1.5 to 5 percent. A significant portion of the nation's mineral resources are presently lost in the form of particles with very fine grain size. In the case of copper, for example, approximately 225 million tons of ore are concentrated by flotation per year in the United States. Total losses from porphyry ores are generally 15 to 20 percent with half of these losses being finely-divided copper sulfide minerals which do not respond to flotation. The additional 5 to 10 percent loss is the result of copper oxide minerals which are not floated. The losses of copper sulfide minerals are thought to be due in part to the lack of appropriate dispersion of the finely-divided solids less than 20 microns in size. To effect dispersion in flotation systems, sodium silicate is commonly added. Enhanced dispersion effectiveness is achieved when polyvalent metal salts are combined with sodium silicate. Since originally described by Patek (1), numerous workers have explored the utility of metal silicates. Makrousov (2), Belash et al. (3), and Eigeles (1950) (4) showed the applicability of these reagents to calcite/apatite and fluorite/calcite ores. Mercade (5, 6) reported depression of calcite in the presence of 3.33/1 mole ratio Al/Si hydrosols prepared from Type N sodium silicate (Si02/Na20 ratio 3.22/1) and 1% A12(SO4) 3•18H20 solutions. He importantly observed that the colloidal precipitates did not play a significant role in dispersion and depression but that the soluble species were responsible for this action. Patented work by this author described metal silicates used to depress calcite in scheelite flotation using 1% metal salt (FeSO4•7H2O, CoSO4•7H2O, etc.) and 5% Type N sodium silicate solutions to produce hydrosols with Si/Fe or Si/Co ratios of 8.79/1. Aluminum (III) ion systems were less effective as depressants than the iron and cobalt systems. Yang (8, 9) has studied metal silicate sols for use in the flotation of lithium and ultra-fine hematite ores. Using 10/1 Si/Fe mole ratio hydrosols prepared from 2% ferric nitrate, Fe(NO3)3.9H20, and 5% Type N sodium silicate solutions, solutions, he showed that the hydrosols either modify the slime particle surfaces or are adsorbed on the slime particles preventing anionic collector adsorption. In a subsequent patent, Yang also reported the use of these hydrosols as dispersants for beneficiation of lithium ores. Recent studies of aluminum silicate hydrosols in the flotation of chalcocite, chalcopyrite and scheelite have been reported using Si/Al dispersants prepared from 5% Type N sodium silicate and 0.1 M aluminum chloride (A1C13.6H20) solutions. Dispersant properties were shown to be dependent upon the method of synthesis, supernatant pH, and the hydrosol Si/Al mole ratio. Polymeric soluble species in these hydrosolsupernatants have been proposed as the active dispersant species. Aluminosilicate hydrosols are synthesized by the general reaction scheme presented in Figure 1. Commercial sodium silicates are available with ratios of SiO2 to Na20 of 1.60-3.25. The sample which is most frequently employed is Type N whose ratio of Si02/Na20 is 3.22/1.00. Gel filtration chromatography and NMR studies have shown that these sodium silicates contain numerous species of molecular weight from 325-2,000 gm/mole. Monomeric, oligomeric and higher molecular weight linear polymeric arrangements of these structures are found in these solutions.

Jan 1, 1989

By John Bley

White Pine Copper Company operates a mine in the Upper Peninsula of Michigan using a modified room-and-pillar system for extracting ore.1 Mine production averages 15, 500 tons per day. The terrain is predominantly level and the depth of cover varies from 500 to 800 feet over the present workings with depth increasing as mining progresses down the dip. The deposit is situated on a low angle plunging, anticlinal structure composed of sedimentary beds. Local terminology for the stratigraphic units which contain the ore horizons, named in ascending order, is as follows: lower sandstone, parting shale, upper sandstone and upper shale. The ore zones of copper enrichment are, contained in the parting and upper shales. The parting shale will vary; from 6. 5 to 9.0 feet thick; the upper sandstone from 2 to 10 feet; and the upper shale from 1. 5 to 6. 5 feet. Two variation of the room-and-pillar system are used to extract the ore depending on grade and local ground conditions. One system is called the parting shale method and recovers the parting shale only. This system requires a mining height of 8 1/2 feet to accommodate large-scale, high-capacity equipment and this working height is obtained by removing approximately 1 to 2 feet of the barren lower sandstone with the ore. Under the second system, locally termed full column, the mining height is about 14-1/2 feet and this system removes the parting shale, the upper sandstone and the lower mineralized zone, approximately 1-1/2 feet, of the upper shale at which point it is possible to maintain a competent back (Fig. 1).1

Jan 1, 1964

By S. K. Mishra

Introduction The history of the Australian coal industry is almost as old as the history of Australia after new settlement. The first cargo of coal was exported from Newcastle to India in 1799. Coal has been mined in Australia for almost two centuries. But there are indications that the first coal was processed in 1877 in the Newcastle area. This is nearly 50 years after the first coal processing in Europe. Processing on any significant scale began in 1944 at the Newcastle Steel Works. In Queensland, however, coal processing did not begin until the second quarter of this century. The dramatic growth of mining and processing of Australian coal since the mid-60s is primarily due to the expansion of the export market in Japan, Asia, and Europe. Australian coals Black coal occurs in most of the major sedimentary basins of Australia. The better known deposits of commercial importance are in the Sydney, Bowen, Oakland, and Gailiee Basins. Apart from the Collie Basin in western Australia, other coal deposits of the Arckinga Basin in South Australia, the Bonaparte Basin in Northern Territory, and the Tasmania Basin are basically unexploited. The Sydney Basin of New South Wales and Bowen Basin of Queensland remain the major producers of black coal in Australia. Currently exploited or potentially commercial deposits of black coal in Australia occur in strata ranging in age from Permian to Tertiary. Estimated black coal reserves are summarized in Table 1. Coals from different ages have significant differences in their petrographic characteristics. Many of the Permian coals are usually rich in inertinite. Jurassic and Tertiary coals are typically rich in vitrinite content. Typical petrographic and chemical characteristics of some important Australian coking coals are summarized in Tables 2 and 3. The reserves of coking coals are restricted in the main to the Permian coals of the Sydney and Bowen Basins. Coal deposits in the latter are at shallow depth. A high percentage of these are being strip-mined. On the other hand, in the Sydney Basin, the majority of the reserves of good quality coking coals are at significant depth. The mining cost of these deposits is substantially higher than those in the Bowen Basin. It is usually possible to make strong coke with Australian Permian coals of vitrinite content much lower than the other international coals. But there are many major Permian deposits in Australia where low vitrinite content presents problems. As they are classified as marginal coking coals, optimization of their pro¬cessing plays an important role in meeting the market specifications of coking coal. The major reason for processing Australian coal is to reduce the ash content. Compared with British and some American coals, Australian coals are of relatively high ash content. Unlike American coals, more than 99% of the Australian coal deposits have sulfur content less than 1%. Consequently, sulfur control has never been a major problem. The coking quality of coal is improved simply through the ash reduction in the marketable product. However, with the increase in intensive mechanization and multi-stage handling of coal be-

Jan 9, 1985

By W. J. Schlitt

Introduction A major uncertainty in assessing the potential for heap-and dump-leach projects is how to determine the extraction-rate curve for the recovery of the mineral values from coarse ore. Such material could either be run-of-mine (ROM) or primary crushed ore. The problem with field testing coarse ore, especially for new projects, is the large scale and extended leach times needed to accurately determine the final extraction-rate curve. At least 5 x 103 to 5 x 104 t of representative ROM ore are typically required for a copper test heap, and much more is often used. Kennecott, for example, recently constructed a 0.9 Mt (1 million st) ROM test heap at the Bingham Canyon Mine in Utah. In such coarse ore operations, the ultimate level of extraction will require a leach cycle that can extend from several months to a few years. Quite often, project development schedules do not provide the luxury of mining such large quantities of material or running such long tests. Instead, test data are usually limited to results from column leach studies on relatively fine ore, often with a top size that does not exceed 25 mm. Maximum leach times are also short, typically less than a year before an initial decision is needed on project viability. Proposed method One approach to estimating the recovery from a coarse ore leach is to assume that the leach solution will have some ultimate penetration distance into the rock. Then, the final level of mineral extraction in this "leached rim" will equal the ultimate level of extraction identified in various testing programs. Obviously, if the radius of a given rock fragment is less than the penetration distance, that fragment will be fully leached at the end of the operation. With larger rock sizes, the percent recovery will fall off as the size increases and the fraction of unpenetrated rock mass increases. Such an approach sounds simple but is likely to be complex when applied to a real project. For example, the penetration distance will be a function of both the rock characteristics and the effective length of the leach cycle. The important rock characteristics include rock porosity, the degree of internal fracturing and the mode of mineral occurrence. With regard to the latter, penetration is likely to be greater if the leachable mineralization occurs on fracture surfaces or in veinlets, as opposed to fine grains uniformly disseminated throughout the rock mass. An estimate of penetration distance may be derived from column or heap tests by noting the depth of solution penetration into the larger rock fragments after three, six and 12 months of leaching. While the penetration rate is ore specific, something on the order of 10 to 20 mm/y may be appropriate for competent, primary copper (chalcopyrite) ore. For gold in tight quartz, the rate may be about the same. Copper oxide ores and gold that is hosted in a more porous rock matrix are likely to have penetration rates that are at least two to three times higher, and an even higher rate should be appropriate for uranium hosted in sandstone. As noted above, the length of the effective leach cycle is likely to be measured in years. On this basis, the ultimate penetration distance (dp) would vary from less than 50 to several 100 mm when a particular ore is leached to exhaustion. Several sets of mathematical manipulations are necessary to convert a rock size distribution and corresponding value of dp into an estimated extraction-rate curve. The first step is to break the ROM size distribution down into intervals and then calculate the radius for the mean rock size in each interval. This is shown in Table 1 for rock sizes up to 1.75 m (about 6 ft) in diameter. The next step is to calculate the volume of unleached core and the fraction of rock that is leached. This is done for the following three values of dp: 25, 100 and 250 mm. Results are shown in Table 2. The third step is to select the ultimate level of recovery that will be achieved in the fraction of material that is effectively leached, i.e., the outer zone that is penetrated by the leach solution. This is clearly a site-specific factor that can only come from metallurgical test results on representative ore

Jan 1, 1998

By M. Y. Fisekci

Subsidence measurement methods, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada are described. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suited methods for our conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the network of laser surveying over the workings of the new hydraulic mine. The site particulars and the mining method of the concerned area have been described briefly. The observation over the old hydraulic mine indicate that panels adjacent to each other do not obey identical subsidence phenomenon.

Jan 1, 1982

By T. D. Kaufmann

When Dr. David Gully solicited this paper last spring a few questions basic to commodity trade between the U.S. and world markets appeared perplexing. Why, for example, when the demand for aluminum was at a peak and when little expansion of capacity had taken place, was the dollar price half of what it had been at the previous peak? Or, why in 1984 when imports surged by 50% as the U.S. economy pulled out of its recession did the dollar not fall, but rather rose by 35%? And, why when the experts all seemed to agree that the dollar was grossly overvalued did the price of gold continue to decline? Surely these were extraordinary times for the mineral economist. When this paper was written in late July, 1985 the answers seemed clearer. The prices of many commodities were not low - the dollar in which they were denominated was too high. In other currencies many commodity prices were indeed high. The dollar was overvalued in trade terms by some 40% caused by an influx of short term coupon investments made by foreign money managers to take advantage of the higher short term interest rates in the U.S. relative to other international banking centers. With a decline in the relative difference in interest rates, an unhealthy buildup of foreign bank accounts and a perception that the dollar would fall, the dollar did start to decline rapidly.

Jan 1, 1985

By G. R. S. Smith

In any filtration, it is primarily the filter medium (cloth) and cake filtering properties that control the type of filtration equipment used and filtration conditions. The advent of new types of filter cloths, such as the membrane cloth discussed in this paper, can result in significant changes in filtration techniques and areas of application for filtration. For many suspensions, for instance, conventional filtration is uneconomic compared to gravity separation or not filtering at all (as with product recovery from dilute streams) because the solids are very fine, are hard to retain and build up filter pressure rapidly, and once retained are hard to remove. As a result of the developments discussed here, this is no longer the case. This technique and the use of the membrane filter cloth is well established. This filtration is currently being used for white liquor filtration in twenty-four mills worldwide in the chemical recovery step of the kraft process for producing paper pulp where it is replacing gravity thickeners in new plants. Filters up to 1000 sq. ft. (100 sq. meters) are filtering large volumes of solids from hot caustic solutions. The filtration materials and techniques discussed in this paper open the way to new methods and applications for filtration in the mining industry. It is not the intention of this paper to give a vigorous analysis of the different separations, but to outline some of the ways in which this filtration technique might be used in the mining industry.

Jan 1, 1989

By W. -C. Huang

In this paper, a methodology for the reliability assessment of geogrid-reinforced unpaved roadways is presented, by taking into account the variability of the subgrade?s undrained shear strength. Analyses are performed using the Point Estimate Method and the Monte Carlo simulations technique. The undrained shear strength is represented by its correlation with the California Bearing Ratio and it is modeled as a random variable following a long-normal distribution. Analyses are performed for different types of reinforcement. The study provides a quantitative assessment of the variation of the system?s probability of failure with this parameter. Overall, the approach suggested in this study may be considered as a complementary approach on the traditional concepts of global or partial safety factors.

Jan 1, 2008

By Siddhartha Agarwal

The mining industry collects a significant amount of operational data. However, gleaning useful information from the terabytes of data is difficult, and not just because of the sheer volume of the data. Therefore, an automated tool was developed at the University of Alaska Fairbanks to go through data and apply sophisticated statistical and neural network techniques in order to identify the data streams that are important to a process. This paper presents results from the tool as applied to SAG mill data from a gold mine. The results were compared to results achieved earlier with available commercial modeling tools. The comparison indicates that there was little or no loss in performance by automating the very complicated process of neural network modeling. Therefore, the intent of the exercise, to examine if complicated modeling tasks can be automated, was realized. Mining Engineering, 2011, Vol. 63, No. 12, pp. 52-54. Official publication of the Society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By Clifford O. Hamilton

In both mature and young maintenance workforces, the workforce commonly lacks some of the skills required for their assigned work. We call this the "skills gap." This skills gap usually exists in a new operation because although you may hire qualified maintenance personnel, they more often than not have little if any experience with the specific equipment at the facility. Performance Associates International, Inc., has developed and proven a technique to address the maintenance skills gap that is usually found in a new operation.

Jan 1, 2001

By Gail Moulton

Searles Valley is located approximately 125 miles northeast of Los Angeles in the Basin and Range Province. Occupying the lowest part of the valley is Searles Dry Lake Playa, which is about 9 miles long and 7 miles wide. Three major subsurface evaporite horizons have been identified and are termed from bottom to top, the Mixed Layer, Lower Salt and Upper Salt. The evaporite beds were formed by desiccation of runoff from the eastern Sierra Nevada during Quaternary time. The saline beds are generally brine saturated with the important ions being sodium, potassium, carbonate, bicarbonate, sulfate, chloride and borate. These ions are present in the brines in various concentrations and have combined to form the minerals halite, hanksite, trona, nahcolite, burkeite, borax, thenardite, sulfohalite, glaserite and others. North American Chemical Company selectively pumps the interstitial brines to feed their chemical plants located on the western edge of Searles Lake. Minerals have been mined since 1873, beginning with borax and trona scraped from the surface. Brine processing began in 1914 with potassium chloride and borax recovery. Expansions have added sodium sulfate and soda ash to the product mix. Currently, dredging of trona ore is also taking place.

Jan 1, 1995

By Zhongxue Li, Baolu Zhou, Yiqing Zhao

"Rare earth elements (REEs) are a kind of new materials which have excellent optical, electrical and magnetic properties, and they play an important role in the development of high technology and green energy industries. With abundant reserves and a wide range of REE type, rare earth industry has a rapid development in China in recent years. However, environmental issues associated with REE exploitation have severely restricted the sustainable development of rare earth industry in China. At present, literatures on the externalities of REE exploitation are very limited, especially in China. This paper builds an evaluation model based on life cycle evaluation to estimate the external costs of REE exploitation at Bayan Obo. The results show that the external costs for producing one metric tonne of rare earth oxides (REO) in Bayan Obo was CNY 34739 in 2013, the external costs of waste gas, waste water, radioactive substance, REE resource depletion, and land occupation are CNY 14945, 12515, 1400, 3199, and 2680, respectively. Waste gas and water constitute about 79% of the total external costs. The internalization of the external costs would reduce the financial profit of Northern Rare Earth (Group) by 18%. This study has taken into account only those externalities whose market values can be estimated, and therefore the external costs of REE exploitation in Bayan Obo is likely to be underestimated. The results fill the gap in literature and provide further understanding on the external cost of REE exploitation.Introduction / Background Along with increasing concern about environmental pollution problems caused by the usage of fossil fuel and the shortage of fossil energy, a transition has occurred where development has moved toward green and renewable energy sources with less pollutant emissions (Stegen 2015). Rare earth elements (REE) are a group of important raw materials for these trends since they have unique magnetic, electronic and optical properties, and thus make them widely used in making high-performance magnets and energy saving lamps (U.S. DOE 2010). In addition, REE are crucial for manufacturing of widespread high-tech applications in medical, defense and electronic industries. Many countries have made medium-term and long-term plans for the development of their REE industries, and the annual growth rate of global REE demand is expected to increase by 6% by 2020, and reach about 170,000 metric tons of rare earth oxides (REO) by 2020 (Rollat et al 2016)."

Jan 1, 2017

By A. E. Koski

This paper describes the implementation of specialized software in mine planning at the Cleveland-Cliffs’ managed Empire Mine on Michigan’s Marquette Iron Range. The application puts together years of mining experience on the eastern end of the Marquette Range beginning in the early 1960’s. The Empire Mine, in its thirty-fifth year of production, uses the software to model a complex and highly variable low grade magnetite orebody, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short and long range planning.

Jan 1, 1999

By George P. Demopoulos, Vladimiros G. Papangelakis, Dimitrios Filippou, A. J. Monhemius, G. W. Warren, E. Peters

A new method developed for the estimation of the activity of Ht in mixed sulfate solutions is described and examples of application of this method to the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3 from 298 to 473 K are offered. The method makes use of an "extended Debye-Hiickel" type of equation that was originally put forth by Das for pure H2SO4 solutions at ambient temperature. The treatment of mixed sulfate solutions was made possible by combining that equation of Das with a speciation algorithm which calculates the abundance of all species formed. The developed method, which also takes into account ionic strength and temperature effects, was used to generate hydrogen ion activity and speciation data for all possible acid/metal sulfate pairs of the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3. Finally, under the light of the reported data, specific examples of hydrometallurgical reaction systems are analyzed in terms of thermodynamics or kinetics. In particular, the systems discussed are: hydrometallurgical precipitation of hematite, solvent extraction of Fe(III), acid leaching of zinc ferrite, and oxidation of Fe(II) to Fe(III) by O2(aq).

Jan 1, 1993