Search Documents

By Jack W. Eloranta, Michael J. T. Orobona, Peter R. VanDelinder

Ore blending for process optimization is becoming an increasing factor for managing cost and productivity. Economic mining and processing a very low value ore in an extremely competitive market results in constant cost-cummng initiatives. The inherent conflict between the lowest possible mining cost and the lowest possible milling cost is reviewed here in the context of blasting for autogenous mills. Iron ore blending focuses on a number of properties-liberation values, weight recovery and concentrate silica being the most important. Other chemical and metallurgical factors are also commonly controlled. Recent research has fueled an emerging interest in blending on physical ore properties as well. Fully autogenous mills rely on the large, competent fraction of crushed feed to act as grinding media. Previous test work indicated that Hibtac mills require specific amounts of 6- to 10-inch ore. High recirculating loads require a steady influx of large rock fragments. Blast designs, therefore, are presently characterized by wide patterns and low powder factors. Current efforts are aimed at improving mill throughput while reducing overall energy costs. Based on research and published case studies and the advent of optical measuring devices, Hibbing Taconite Company has embarked on a blast optimization program to identify optimum mill feed and to design blast fragmentation goals for each geological unit and each mining area. This paper outlines the preliminary findings of an ongoing, broad-based team effort which requires close cooperation of geologists, mine engineers, crushing and milling personnel. Three specific areas of investigation are reviewed: I) Historical relationships between powder factor and mill performance, 2) Blast fragmentation modeling using the Kuz-Ram model, and 3) Drill

Jan 1, 2004

By Scott Brien, O&apos

Cyclones have become standard unit operations in mineral processing for both dewatering mineral slurries and for making separations at given particle sizes. Conventional cyclones are normally able to make moderately sharp cuts. However, the limited ability to control water flow out of the apex means that cyclones have difficulty handling fluctuations in feed. Underflow-regulated cyclones are cyclones with a rubber boot attached to the underflow. This boot acts as a non-return valve and restricts flow out of the apex of a cyclone. Normally, this type of restriction on a cyclone causes severe difficulties in cyclone operation. However, by adding a siphon arm to the overflow, water flow can be controlled. The siphon arm creates a vacuum that reduces or eliminates the air core, permitting better control of the ratio of water flow out of the overflow and underflow. A Linatex-developed underflow-regulated cyclone was compared to a conventional cyclone for its ability to dewater a sand slurry. The underflow-regulated cyclone produced slurries with solids contents as high as 80% in the underflow. Conventional cyclones produced lower solids content in the underflow under similar conditions.

Jan 1, 1997

By R. Sharma

The heterogeneous distributions of nodule sizes, cover-ages and abundances and the variability of their burial und association with sediments and rock outcrops on the seafloor have emerged as crucial parameters in considering the exploitation potential of the manganese nodules in the central part of the Indian Ocean. Nodules with the long axis measuring from 20 and 40 mm (0.8 and 1.6 in.) account for nearly 60% to 70% of those evaluated from photographic and grab-sample data. In addition, 75% of the nodules (by weight) are between 20 and 60 mm (0.8 to 2.4 in.). The distribution of nodules with abundances ranging from 1 to 20 kg/m2 as well as coverages of 1 % to 90% on the seafloor are important considerations in demarcating the potential areas for nodule mining. The mining of areas with higher concentrations of nodules, such as along slopes associated with less sediment, would result in the enhanced recovery of nodules compared to areas with low nodule concentrations, such as in valleys and plains where thick sediment covers occur. The mining head will encounter substrates such as hard rock exposures, either with or without Fe-Mn encrustations, as well as soft sediment layers in the nodule fields. It must be able to collect buried nodules under sediment cover, and it must be able to negotiate uphill and downhill slopes in mining areas. Mapping prior to mining must delineate areas to he avoided and must define locations to be mined. The requirements suggest that the nodule collector must be a dynamic (active) system with sensors to detect areas of potential nodule concentrations, as well as features that are hazardous (or unfavorable) for mining operations.

Jan 1, 1999

By Mahesh C. Jha, Frank J. Smit

Column flotation and selective agglomeration are promising advanced physical cleaning processes that can be developed for preparing premium quality coal-water slurry fuel from coal fines. Such a fuel could either replace oil or natural gas in certain industrial and utility boilers or else could be burned in advanced combustors currently under development. These applications require coal cleaned to sulfur and ash contents below 258 g/GJ and 430 - 860 g/GJ (0.6 lb/million Btu and 1 - 2 lb/million Btu), respectively, to meet clean air emission requirements. A highly loaded slurry must be produced in order to avoid derating the boilers, and the total cost of the fuel must be below $2.37/GJ ($2.50/million Btu) in order to penetrate the market by the turn of the century. Achieving these technical and economic goals depend critically on the selection of suitable feed coals. This paper describes the identification and evaluation of 18 coals and final selection of six coals from different regions of the United States as potential feedstock for preparation of premium fuel. The work is being performed under a cost-shared DOE project.

Jan 1, 1995

By H. L. Ehrlich

Modes of microbial attack of metal carbonates, metal silicates, metal oxides and metal sulfides are summarized. The current status of microbial redox mechanisms, whereby metals in metal oxides and sulfides are mobilized, is discussed. Opposing theories of a single mode of attack involving interaction with a microbially produced reductant or oxidant in the bulk phase and of dual modes of attack involving a reaction requiring physical contact between microbe and mineral surface on the one hand and microbial production of a reductant or oxidant in the bulk phase that reacts with the mineral on the other hand are considered. No one mode when finally completely unraveled should be expected to fit all cases. Some biochemical, electronmicroscopic and spectrophotometric approaches for elucidation of missing details of different modes are suggested. Key words: Bioleaching, Biobeneficiation, Metal mobilization

Jan 1, 2003

By W. J. Wuest, M. J. DeMarco

The US Bureau of Mines (USBM) recently developed a rock-mass classification system for evaluating the structural competency of bedded roof strata. The system is called the coal-mine roof rating (CMRR), When compiled with the companion Lotus 1-2-3 spreadsheet, CMRR data are a useful tool with applications to longwall gate-road pillar design, safety-hazard mapping and artificial roof-support analysis. This paper gives a review of some applications under actual conditions found in current US mining operations.

Jan 1, 1997

By Liu Hanzhao, Jin Yongduo

Many gold ores which are not only submicroscopic but also rich in arsenic and organic carbon, for example Dongbeizhai Mine, have been found in china. These ores belong to the most refractory ores The key to the recovery of gold from these ores is preoxidation. Dongbeizhai ores have been tested with biooxidation, chlorination, double oxidation, acidic and alkaline pressure oxidation, catalytic oxidation, NITROX and roasting. To date it appears that either roasting or pressure oxidation is optimal. It is suggested that the flotation-roasting (or pressure oxidation)-CIL process should be used to treat this type of ore.

Jan 1, 1995

By R. A. Jankowski

The US Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain-setback distance, operator positioning and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels, on the order of 0.5 to 1.2 mg/m3, were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust-control system for extracting deep cuts up to 12.2 m (40 ft) in length. The impact on methane was not evaluated.

Jan 1, 1998

By Glenn A. Shirey, Robert D. Stoessner, S. Gopalakrishnan

Under a contract awarded by the U.S. DOE-PETC, the Pennsylvania Electric Company and New York. State Electric and Gas Corporation are conducting a test program to evaluate and optimize the performance of a two-inch air-sparged. hydrocyclone (ASH) for cleaning fine coal. The test program is being conducted at the Homer City EPRI Coal Quality Development Center, utilizing Upper Freeport coal classified to minus 0.15 mm as the process feed material. A matrix of experiments has been conducted to establish the influence of significant design and operating variables (including overflow and underflow orifices, inlet slurry pressure, airflow rate, and reagent dosage) on the production of deep cleaned coal. Performance of the ASH is being compared to conventional froth flotation, utilizing advanced techniques and selected flotation reagents. This paper focuses on work completed to-date to optimize the performance of the air-sparged hydrocyclone for cleaning fine coal. INTRODUCTION The Pennsylvania Electric Company (Penelec) and New York State Electric and Gas Corporation (NYSEG) have been evaluating advanced fine coal cleaning processes for the production of compliance grade coal (1.2 pounds S02/million Btu). Laboratory bench-scale froth flotation results were compared with results of advanced flotation processes as performed by various organizations, utilizing the same coal feed. Among the processes evaluated, the air-sparged hydrocyclone (ASH) - developed by Dr. Jan Miller at the University of Utah - was considered to offer the best potential for retrofitting into an existing coal preparation facility because of the increased capacity per unit volume. The ASH has been shown to process over 100 times the throughput of conventional froth flotation cells. In May of 1988, Penelec/NYSEG was awarded a contract from the Department of Energy's Pittsburgh Energy and Technology Center (DOE-PETC) to optimize the performance of a five cm (two inch) ASH for producing compliance grade coal from raw classified minus 0.150 mm (1.00 mesh) Upper Freeport coal, and to compare its performance with conventional froth flotation utilizing advanced techniques and selected flotation reagents. The test work is being conducted at EPRI's Coal Quality Development Center (CQDC) in Homer City, Pennsylvania, utilizing a circuit processing 0.10 to 0.25 tons of coal per hour. Other members of the Penelec/NYSEG contract team include the University of Utah, Advanced Processing Technologies, Inc., Davy Dravo, Kaiser Engineers, Ebasco Services, and Management and Technical Systems. ASH DESCRIPTION AND OPERATION The ASH-2 System is a five cm ID (actually 4.76 cm) air-sparged hydrocyclone manufactured by Advanced Processing Technologies, Inc., under license from the University of Utah, for the purpose of research, evaluation and development. A schematic drawing of the air-sparged hydrocyclone is presented in Figure 1. Basically the air-sparged hydrocyclone consists of two concentric right-vertical tubes, a conventional cyclone header at the top, and a froth pedestal at the bottom. The inner tube is a porous tube through which air is sparged radially. The outer nonporous tube simply serves as an air jacket to provide for even distribution of air through the porous inner tube. The slurry is fed tangentially through the conventional cyclone header to develop a swirl flow in the radial direction. Air is sparged through the jacketed, inner porous tube wall and is sheared into small bubbles by the swirl flow. Hydrophobic particles in the slurry collide with these bubbles and, after attachment, are transported radially into a froth phase which forms on the cyclone axis. The froth phase is stabilized and constrained by the froth pedestal, thus moving towards the vortex finder of the cyclone header and discharged as an overflow product. Hydrophilic particles generally remain centrifuged in the slurry phase and are discharged as an underflow product through the annulus created by the froth pedestal.

Jan 1, 1989

By M. Saidman, R. Pizzuti, R. Hirschfeld, A. J. Desai, J. Rand

Two bedrock tunnels, 170 to 250 feet deep and with a length of about 17,000 feet each, will be used to convey cooling water from the Atlantic Ocean to the Seabrook, N.H., Nuclear Power Plant. Seismic reflection and refraction surveys were used to obtain preliminary information about overburden and bedrock conditions. A major boring program, including core orientation and water-pressure testing, was undertaken to provide detailed geologic data. The results of the geotechnical investigation were summarized in terms of rock type, frequency and character of joints, degree of weathering, modified core recovery (RQD), pressure-test results and strength and hardness. These parameters were used as a basis for evaluating the feasibility of using a tunnel-boring machine, for designing and estimating the initial support systems, and for evaluating the grouting and tunnel lining requirements.

Jan 1, 1976

By Norman E. Breslow, John A. Montgomery, Sanford W. Horstman

Reconstruction of historical exposures to silica dust is required in an ongoing cohort mortality study of workers in the diatomaceous earth (DE) industry. However, historical data were collected using three different sampling methods. This study was conducted to derive empirical quantitative relationships from linear regression equations between the three methods: standard impinger, total mass, and respirable mass. Dust from one diatomaceous earth processing plant was sampled simultaneously by all three methods. Results from 61 clusters of the three sampling devices indicate that the phcle size distribution of the dust varies with the two parent products sampled. baghouse product and main product. The relationships between particle counts and respirable mass are: Respirable mass (mg/m3) = 0.064 (mppd) impinger count for baghouse product dust, and respirable mass (mg/m3) = 0.018 (mppcf) impinger count for main product dust. The relationships between particle counts and total mass are: Total mass (mg/m3) = 0.837 (mppcf) impinger count for baghouse product, and total mass (mg/m3) = 1.21 (mppcf) for main product dust. In all four euuations, the intercept did not differ significantly from zero, and the correlation coefficients ranged from 0.90 to 0.95. Results are compared with data from four previously published studies.

Jan 1, 1991

By E. G. Joe

Introduction Uranium mining has been actively carried on in Canada for over twenty-five years mainly in Ontario at Elliot Lake in Bancroft, and in Northern Saskatchewan at the operations of Eldorado Nuclear Ltd. During this period, approximately one hundred million tons of mill tailings have been created and lie mainly on the surface close to the mining and milling installations. If all of the present reserves of uranium ores in Canada are mined, a further eight hundred million tons of mine tailings could be created in Ontario, Saskatchewan, the Northwest Territories, Labrador and British Columbia. The present control of effluents from existing tailings is managed by the operating mines under the regulations of both federal and provincial control agencies. It is the long-term effect of these tailings on the environment that has not been clearly defined or measured. Several years ago, the Canada Centre for Mineral and Energy Technology of the Department of Energy, Mines and Resources, embarked upon a program of research directed at the long-term effects of uranium mine tailings. Much of the research to date has been on tailings in the Elliot Lake, Ontario area where some tailings piles have existed for over twenty years. The program consists of two projects, one to address the problem of existing tailings and the other to examine alternatives in the management of current and future tailings. TAILINGS CHARACTERISTICS Uranium tailings are generally the result of sulphuric acid leaching in which the uranium and alkaline minerals such as carbonates and chlorites are leached out. If the ore contains sulphides, these minerals potentially present an additional hazard of acid generation over time and could increase the mobility of heavy metals and some radionuclides such as thorium-230. Except for the extracted uranium, most of the radionuclides from the ore remain in the tailings pile. Uranium ores in Canada span a wide variety of mineralization and associated gangue composition. Uranium minerals include pitchblende, uraninite, uranothorite, brannerite and the phosphate uranium minerals autunite and saleeite. Gangue minerals vary from acid consuming carbonates, and chlorites to acid producing sulphides and inert silicates. With such a wide variety in ore composition, the characteristics of the resultant tailings in Canada are in many cases site specific and the solutions to the long-term effects of these tailings may also be site specific.

Jan 1, 1980

By A. M. Tunstall

Blasting is commonly viewed separately from mechanical handling and crushing. This view is misleading because the degree of fragmentation achieved by blasting can have a significant effect on the efficiency of these processes and, hence, on the overall cost of the mining operation. In this paper, aspects of blasting and crushing and their interaction are examined. A case study is also presented that dramatically illustrates the influence of blast fragmentation on subsequent processing and on the financial implications involved

Jan 1, 1997

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997

By John M. Kemeny

This paper describes a practical technique to estimate the size distribution of large volumes of rock fragments, including blasted benches, waste dumps and heap leach sites. Images are obtained from a site using a standard video camera and downloaded onto the computer. Image processing algorithms are used to delineate the individual rock fragments in the images, followed by the calculation of the area and shape of each fragment. Statistical calculations are then performed to estimate the complete size distribution of the fragments. The accuracy of the technique has been assessed with a number of field validation studies.

Jan 1, 1995

By Larry Whittle

Gold milling activities generate waste streams containing dissolved metals and cyanide, among other contaminants, that require some form of treatment prior to discharging to the environment. To date, this treatment has involved the destruction of cyanide through natural degradation, chemical oxidation, or a combination of both followed by the precipitation of metal hydroxides. Although these processes have been proven to be capable of achieving. regulatory levels for metals and cyanide, they often generate significant levels of cyanate and, at times, ammonia, that may be toxic to rainbow trout and thus undesirable for regulatory compliance. Tallon Metal Technologies Inc. (Tallon) has developed Vitrokele™, a chelating resin that has the ability to capture metals (including gold), both total and weak acid dissociable cyanide, as well as thiocyanate from both slurries and solutions. The loaded resin is eluted and returned to the recovery circuit while metals and cyanide are recovered from the eluent stream. This process was demonstrated at pilot scale at B.P. Resources' Hope Brook Gold Mine in Newfoundland, and more recently at Canamax's Bell Creek Mine near Timmins, Ontario. The results from these pilot programs showed metal and cyanide recoveries of 99% or more with the concentration of cyanide and metals in the effluent reduced to levels with minimal or no toxicity to rainbow trout. Furthermore, neither cyanate nor ammonia were generated from the process. The loaded resin was effectively stripped and re-introduced to the recovery circuit; cyanide was captured in the eluent stream and made available for recycling to the mill leaching circuit; and metals were captured for re-use, sale or disposal. This paper summarizes the results obtained from the pilot tests at the Bell Creek and Hope Brook Gold mine sites.

Jan 1, 1992

By Michael J. Virnig, Keith E. Weerts

The development of heap leach technology for the treatment of low grade gold and silver ores has led to a boom in gold production in the Western United States in the last 15 years. The heap leaching process consists of stacking the mined ore on a specially prepared leach pad followed by leaching with dilute alkaline cyanide solution. Depending on the nature of the ore, it may require crushing and/or agglomeration prior to stacking on the leach pad. As the dilute alkaline cyanide solution migrates down through the stacked ore, the precious metal values along with a portion of the base metal values present in the ore are dissolved to give a pregnant leach solution which is collected at the base of the stacked ore. The precious metal values are then recovered by zinc precipitation or by adsorption on activated carbon. Once all of the economic metal values have been leached from the ore, the spent heap leach pad, the leached materials, and associated process solutions must be decomissioned. Decommissioning requires that the spent heap leach pad along with the leached materials and process solution be treated to reduce the concentration of the residual cyanide, base metal cyanide complexes, and other anionic metal species to levels where they no longer represent a long tenn liability for the environment and the operator. The levels to which these components must be reduced is dependent upon the applicable water quality standards as determined by the responsible federal, state, and local agencies. As environmental awareness has grown, these standards have become increasingly stringent. A number of treatment options have been developed for the de-toxification of the process residues. These include natural degradation which incorporates bio-degradation, fresh water rinsing, alkaline chlorination, hydrogen peroxide, and sulfur dioxide/air. Each of these options has been reviewed with regard to relative effectiveness, generation of hazardous by­products, reagent handling considerations, relative costs, and time requirements by Denton, Iverson, and Gosling I. As an outgrowth of the program to develop Henkel's guanidine based gold extractants, COGNIS, Inc., the environmental ann of Henkel, has developed the CyanoMet R process for the extraction and concentration of the various cyanide and anionic metal species from the dilute aqueous alkaline solutions generated during the process of detoxifying spent heap leach pads. This paper describes the CyanoMet R process, its application to three different feed solutions, and treatment of the concentrate generated by the process.

Jan 1, 1993

By F. L. Wilke

A model is presented to minimize the winning costs per shift within the different sections of a potassium mine by liner programming and to simulate the other areas to get all costs in order to comp re different production strategies. he model is based on a a given total layout of the underground mining which is considered to be fix during the planning period. Room-and-pillar mining is assumed to be used. Potassium extraction is done by drilling and blasting. Transportation of the raw material to sectional crushers is done by scoop-trams where it is crushed to coarse-grains which allow further transportation by conveyor belts to the hoisting shaft or to a bunker. When production is stopped, the continuously working factory is supplied by means of this bunker. Starting from a desired composition of the raw material the model has to keep the given total. demand of raw material per shift, to minimize the winning costs, to keep the capacity constraints of the equipment and to determine the planned output of production of the sections per shift. Costs of the areas which follow the extractions are added to extraction costs in order to allow a comparision of costs of several alternatives of production. Optimization in extraction and assignment of scoop-trams to sections is done by linear programming. The other areas of the mine are treated by simulation. The model output is a schedule of the calculated costs broken down into costs of processes, equipment, and kinds of costs. This proceeding enables to compare different ways of production.

Jan 1, 1979

By W. C. Shanks

The Pioche District of Lincoln County in southeastern Nevada (Figures 1 and 2) has been an historically important producer of silver, zinc, and lead. Economic geology of districts in the Pioche area is summarized most adequately in recent reports by Tschanz and Pampeyan (1) and Gemmill (2) and only a few major aspects will be discussed here. Production in the Pioche District began in 1869 and early mining concentrated on silver-bearing fissures in lower Cambrian quartzites. In the early 1870's the Pioche District was second only to the Comstock Lode in world silver production (3). More recent mining activities have centered on the other major ore type in the area, bedded replacement of lower Cambrian carbonates by Ag-Zn-Pb sulfide ore. Production of replacement ore peaked around 1950. The present study is focused on the Pan American Mine because it is an excellent example of low grade carbonate replacement deposits, because there is little structural dismemberment, and because access was readily available. Most previous workers have suggested that both the fissure vein deposits and the bedded replacement deposits of the Pioche districts are a result of spatially related Laramide igneous activity. The purpose of this study is to determine whether ore genesis is a result of igneous activity or if mineralization might be related to late diagenetic processes such as formed Mississippi Valley "type" deposits. Stable isotopes of sulfur, carbon, and oxygen in ore and gangue minerals have been studied to determine the probable isotopic composition of the ore fluid and paleomagnetic studies of the carbonate rocks have been utilized to determine timing of mineralization. Additionally, petrographic and field studies of carbonate lithologies were undertaken in an attempt to delineate non-structural controls on ore localization. These studies are still proceeding and the results presented herein are, therefore, preliminary in nature.

Jan 1, 1979

By G. J. Schneider

The higher stress zone adjacent to an underground opening causes a velocity anomaly that can be mapped in favorable conditions with an acoustic cross-borehole logging system. Bureau personnel used a specialized system at the Colorado School of Mines test site near Idaho Springs, Colorado, to locate the Edgar Mine tunnel and its associated stress anomaly. Data from the logging system' were processed with a tomographic image reconstruction algorithm to map the opening and the location of the high velocity zone around the opening. The velocity imagery from tomographic analysis compared favorably with predictions from numerical modelling of the location of the stress anomaly.

Jan 1, 1988