Search Documents

By Andrew L. Mular, Richard R. Klimpel

Optimization strategies of possible interest to mineral processing are reviewed and typical strategies initiated in processing plants to date are discussed. Both On-Line and Off-Line optimization procedures have been employed by industry, assisted either by operators or by digital computers. In every case, dollar benefits have accrued.

Jan 1, 1991

By John C. Draper

[Duquesne Light Company's three power plants in western Pennsylvania are now receiving high BTU clean coal from a new coal preparation plant. When burning coal from this plant, particulate emissions are greatly reduced and the sulfur content of stack ace descend. The cleaner coal also leads to more effecting overall operating of the power plants because of less bulk handling of fuel and ash. Environmental improvement is an important benefit of the cleaner, more complete combustion.]

Jan 1, 1976

By J. D. Miller

Fluid flow phenomena and therefore the flotation efficiency of air-sparged hydrocyclone (ASH) flotation are strongly dependent on the operating and design variables such as air flow rate, slurry flow rate, underflow and overflow opening areas, percent solids in the feed, reagent levels, particle size, ASH length, etc. Time-averaged multiphase flow characteristics, as deter-mined by x-ray CT and described in a previous publication, are used to understand and explain the steady-state ASH flotation of quartz. A detailed parametric study of quartz flotation by a nominal 2-inch diameter air-sparged hydrocyclone (ASH-2C) revealed the influence of these variables on the flotation response which is discussed in terms of the multiphase flow characteristics. Thus, a phenomenological description of quartz flotation has been established to assist in the further development and utilization of the ASH technology.

Jan 1, 1995

By C. G. Tester

Automatic tripper control systems can be reliable and as such are suitable for use in the mining industry. Proper application of fundamental engineering principles provides the means for the reliability. Some of the principles are: (1) Be sure the system designer designs a system that does the job operations people want done; (2) Use sound logic design practices to avoid internal electrical problems; (3) The design must be maintenance oriented; and (4) Use good quality components. I would like to discuss a tripper control installation at Kennecott Copper Corporation, Chino Mines Division, in Hurley, New Mexico, and how these principles apply to this tripper control system. First, however, I will expand on the principles to clarify just what is meant. First, "Be sure the system designer designs a system that does the job operations people want done.? Operator acceptance is often the key to the success or failure of an automatic control system. One of the best ways I know of to get operator acceptance is to give him a system that he wants. I don't mean to imply that if bad practices or procedures exist that they should be incorporated in the control system. I do think that many designers feel they haven't done their job if the control system doesn't do things drastically different than the old manual method. Good engineering principles dictate that the job should be done right and if the manual method was right it can very likely be right for the automatic method.

Jan 1, 1973

By Haydn H. Murray, Sam M. Pickering

The term kaolin is used here, in a commercial sense, for near- white clay deposits which are dominantly comprised of the mineral kaolinite, or for products refined from such deposits. The term "china clay" has been used in the past as a synonym for kaolin, a reference to its first being mined some 3000 years ago at a hill near Jauchau Fu, Jiangxi Province, China as a porcelain raw material. The name kaolin was derived from the Chinese Kauling, which means high ridge. For most modem industrial applications kaolin must be extensively refined and processed from the crude state to enhance whiteness, purity, and other important commercial characteristics. After such processing, kaolin ranks as one of the most valuable of industrial clays, and it is used to some extent in most manufactured consumer products. In 1991, the United States alone produced kaolin valued at $1,072,366,000. It is applied very widely as a pigment, filler, coater, extender, ceramic raw material, catalyst base, electrical insulator, and pharmaceutical. Some more prominent uses include paper filling and coating; paint, plastic, adhesive, and ink pigment; rubber reinforcing agent; ceramic raw material for porcelain, dinnerware, tile, and enamels; catalyst base for petroleum cracking and auto exhaust emission catalytic control devices; cosmetics base; and digestive coating remedy. Those properties of kaolin clay which make it suited to these applications are related to its physical, optical, mineralogical, and chemical nature.

Jan 1, 1994

By David F. Gibson

This paper presents an outline of several models that have been developed to aid surface mine planners evaluate alternative mining methods and dragline sizes. The models presented belong to a larger group of models that are incorporated in the SEAMPLAN computerized mine and reclamation planning system. SEAMPLAN was developed in the College of Engineering at Montana State University. Initial funding for the development was derived from the USDA Forest Ser- vice and EPA. Enhancements to SEAMPLAN are currently being funded by DOE (Contract DE-AC22-80ET-14173). SEAMPLAN is a comprehensive surface mine and reclamation planning tool that contains a number of major modules: Data Entry and Review, Production Analysis, Reclamation Analysis, and Impact Analysis. The Production Analysis Module contains programs that enable the user to evaluate alternative methods of removing overburden in a surface coal mine and then to assess auxiliary activities required to support the overburden removal operation. A set of these programs addresses the use of draglines for removing overburden. Six basic dragline mining techniques have been modeled. For one-pass dragline operations four methods can be analyzed: (i) simple side cast, (ii) side bench, (iii) extended bench, and (iv) extended bench with side bench. Two methods of two-pass operations are modeled: (i) single dragline, and (ii) tandem draglines.

Jan 1, 1982

By Richard L. Bullock

INTRODUCTION TO COAL MINE PRACTICES To illustrate the trends and the proportions of the various methods used to mine coal underground, Fig. 1 is useful. However, of all the underground coal mining practices in the US, room-and-pillar mining still accounts for 96.5%. This percentage is divided as follows: conventional, machine cut-33.0%; conventional, hand cut -1.7% : and continuous mining-61 .8%. As was stated in Sec. 1, Chap. 7, the term "development" means different things to a coal miner and a metal miner. Though some of the ideas and concepts presented in the first two chapters of this section are valid for all types of mines, they apply particularly to mines using noncoal methods. In coal mines (and many other mines using coal mining systems) development refers to that phase of the mining cycle which advances several entries through the virgin seam, forming pillars by cross- cutting between the parallel entries. Because in the past, coal seams (as well as seams of potash, trona, oil shales, gilsonite, salt, and some uranium) have been much more uniform in their thickness, continuity, and quality, and because they often cover large areas, it has been possible to develop the room-and-pillar mine completely from a preplanned, systematic approach with a minimum of surface drilling information. As the better coal seams of the midwest and east are being depleted (or eliminated because of high sulfur), seams of poor quality and continuity will have to be mined. Also, seams that are not nearly so well known at greater depth will have to be taken as well as some of the steeply pitching and folded seams of the west. The American coal miner is only now feeling the need to do a much more complete job of prospecting the geology of the coal seams than he has ever done before. This is the only way that the risk of unknown rock conditions can be minimized. In many ways, surprises in the rock or coal seams are much more of a disaster to the coal miner developing a room-and- pillar mine than to his metal mining counterpart. Be- cause of the multiple entries, the complex set of the Federal Coal Mine Health and Safety regulations, and the totally dedicated design of coal mining equipment, coal mining systems do not have the flexibility to easily overcome changes in the seams mined or the rocks around them. Thus, if a wide parting of rock shows up unexpectedly in the middle of a coal seam entry being milled away by a continuous miner, it will either have to slowly "chew" through it, convert to a conventional mining system, or stop that particular entry. Likewise, if suddenly the coal disappears completely and in its place are the remains of an old creek bed, the "want" or "wash out" as it's called will usually have to be mined right along with the coal, by the same methods and with the same soft rock equipment, or the entry will have to be abandoned. For reasons such as these, coal seams today should be drilled from the surface just as thoroughly as the ore bodies in metal mines. Having once determined a more precise location of where the coal seams are located and which are suitable for mining, the engineer must still take a systematic approach to planning the mine as completely as possible. The initial series of entries must be planned to be driven either from the side hill portal or from the bottom of the shaft or slope. In either case, they should usually intersect the area close to the midpoint of the mass to be mined.

Jan 1, 1982

By P. Bevilacqua, G. Ferrara, M. C. Williams, T. P. Meloy

Tabling is an old environmentally friendly separation unit operation. This paper models shaking tables and explores the action and design of riffles on shaking tables. By reassessing riffle shape and riffle patterns, significant improvements in tabling performance appear feasible. While table sales appear at their nadir, a high-tech environmentally friendly table may have a significant market in the coming decade. Riffles on a shaking table impact particle separation. Particles are affected by riffles and their exit position on the table is dramatically changed, Riffle shape determines how much the riffle will influence a given material. Moreover, riffle patterns influence the concentration of a given material and its exit points on a table. This effect of riffle placement and design is modeled in a spreadsheet. Major performance and separation improvements may he expected by improved table design. Two physical laws of tabling have been derived. These laws aid in the design of sophisticated high-tech tables.

Jan 1, 1995

The Montgary pegmatite is located at Bernic Lake in the southeastern Manitoba pegmatite district. 'It has a complex internal structure with several contrasting mineral assemblages. The pegmatite contains a number of potentially valuable miners including spodumene, amblygonite,. lepidolite, zinnwaidite, pollucite and beryl.. The distribution of each of these within the pegmatite is related to the internal structure and controlled by a specific mineral assemblage. Parts of the pegmatite contain a high concentration of spodumene. The pollucite occurrence is of unique character and is one of the largest known deposits of this mineral. The pegmatite is still-like in attitude with a maximum dip of about 15 degrees. Its contents with the amphibolitic wall rocks are sharp and tourmalinized. Mineral assemblages present include perthite-plagioclase-quartz-muscovite, spodumene-microcline perthite-plagioclase-quartz-muscovite, cleavelandite-lithia micas-quartz, quartz-amblygonite, albite, lepidolite, pollucite, and quartz assemblages. The occurrence and relationships of these are described and possible relationships between attitude and internal structure are discussed. Many features of the pegmatite suggest that the deposit formed by crystallization and differentiation of a pegmatitic fluid in a restricted system. These features are discussed. The nature and occurrence of the pollucite, lepidolite and albite assemblages are such, however that it is difficult to visualize them resulting from such a system. These assemblages may be of later replacement origin. The source of the, late, alkali-rich replacing solutions may be unmixing of soda and the rarer alkalis (lithium, rubidium, caesium) from earlier-formed silicates in a manner analogous to the unmixing of soda feldspar in perthites. Various aspects of this hypothesis are examined.

Jan 1, 1959

By C. T. Holland

Coal mining has been an important industry in the Appalachian area for many years. This is particularly true in the northern part of the area, namely, in Pennsylvania, West Virginia, and Ohio. Also, in the south a great deal of mining activity has been carried on in Alabama, Kentucky, and southwest Virginia. Some of the by-products of this activity has been the production of mineralized water from the mines in copious quantitites. The southern Appalachians have been somewhat more fortunate in that the water there has had a considerable amount of alkalinity in it, which has to a large extent eliminated some of the more undesirable aspects of mine drainage. Northern Appalachia, including central and western Pennsylvania, the Monongahela basin in West Virginia, and the Appalachian area in eastern Ohio have not been so fortunate in that coals in those areas and the top and bottom rock have, in many cases, shown considerable quantities of pyrite, and the water does not carry the carbonates found farther south.

Jan 1, 1969

By Allan M. Johnson

Since 1974 researchers at Michigan Technological University have been studying mine subsidence in the Iron River District of Northern Michigan. The district, which was active from 1881-1978, has had numerous cases of subsidence. Much of the subsidence resulted from rock mass failure but some appeared to have developed primarily in the thick glacial overburden which is a typical feature of this area. This latter observation led to the recognition that some of the surface subsidence was due to piping; i .e., loss of overburden material to the mine voids by groundwater flow (Johnson and Frantti, 1978). The Sherwood Mine was the last mine to operate in the district. With its closedown scheduled for late summer of 1978, a unique opportunity to monitor the mine as it flooded was presented. It was reasoned that with the cessation of pumping, groundwater would rise in the overburden and the mine would flood. The physical characteristics of the mine were favorable for piping to occur as the mine flooded. With the permission of Inland Steel Mining Company and the support of the U. S. Bureau of Mines, a project to monitor the Sherwood Mine for piping subsidence began in June of 1978. This paper present aspects of this study pertinent to the piping-induced subsidence events which occurred at the Sherwood Mine in 1980 and 1981, including acoustic emission monitoring of the subsidence activity, hydrologic monitoring of the groundwater regime and the flooding mine, laboratory modeling of the piping mechanism, and analytic procedures which are under development.

Jan 1, 1982

By Wayne Stange

Due to the availability of user-friendly microcomputer based packages, the use of simulation is increasing.. Users have however encountered problems inherent to the structure of sequential-modular simulators. These are the difficulties associated with estimating parameters for arbitrary' models and the solution of design and optimization problems. The implementation of an optimization routine in the simulator MicroSim has facilitated the solution of such problems. The literature indicates that more efficient numerical techniques for solving optimization problems than those presently used in MicroSim are available. These techniques, together with user-interfaces which allow such problems to be specified easily by users, will result in the development of simulators much more powerful than existing ones.

Jan 1, 1989

By Russell G. Shomperlen

Grinding mills in excess of 5 meter diameter and 3500 kilowatts per mesh are putting new demands on big gears. This paper returns to the basics of ring gear design beginning with the fundamental power formulas specified by AGMA. Specific emphasis is given to those elements in the rating equations which require closer attention as gear diameters and transmitted power increase. Strict process control in the manufacture of the gear blank is also stressed. Finally, the writer offers a guide to proper installation, lubrication and maintenance.

Jan 1, 1981

By C. H. Lee, F. Concha, L. G. Austin, P. T. Luckie

The Concha-Almendra batch-settling treatment for concentrated suspensions of single-diameter spheres has been modified. This modified version is used in the differential equations of simple batch settling of a particle size range of different density materials. The equations have been programmed for a finite difference solution, and a number of test cases have been analyzed. By cutting the settling column at a fixed fractional height, the material below this height can be treated as underflow and the material above as overflow. The predicted partition curves obtained from treating the settling in this way have Sharpness Indices in the range of 0.5 to 0.6, in the absence of dispersion effects. The Sharpness Indices decrease as dispersion increases. When the feed size distributions are of the Rosin-Rammler form, the partition curves (corrected for the bypass fraction) fit the Rosin-Rammler equation with reasonable accuracy. The predicted Sharpness Index of a component of a mixture of two materials of different densities was unchanged from that of the same materials settled alone. However, for the same, feed size distribution and volume fraction of solids in the feed, the heavier material settled faster, and the lighter settled slower, than when settled alone.

Jan 1, 1993

By Norman Weiss

The design of an ore-processing plant requires a high degree of cooperation among the geological, mining and metallurgical engineers. The purposes of this section are to provide mill design information most commonly needed by the mine planners and management, and to summarize the kinds of information that must be supplied to the mill designer to enable him to provide a suitable plant. 28.1-BASIS OF DESIGN NORMAN WEISS 28.1.1-SIZE OF PROJECT The size of the project generally is expressed in tons of ore milled per day, but company policies differ widely in this respect, a few adhering to this set figure but many expecting the design capacity to be liberal. To some companies that follow the latter practice a 25,000-tpd milling plant that cannot reach 30,000 or 35,000 tpd without major additions is a disappointment. The engineers responsible for planning the operation must know what is intended. Equally important are operating schedules, particularly the number of operating days per week and shifts per day for ore delivery, crushing, grinding and processing. Hours per shift also are an important factor in design, particularly in the case of ore delivery, and the percentage lost time expected for maintenance, cleanup, inspection, preventive maintenance shutdowns, and many others, has to be taken into account. Frequently, the ore deposit will vary in hardness and grade to such a degree that the capacity of the mill will vary widely from year to year and cannot be expressed as a fixed figure. but rather as an average over a calculable period, such as 10 yr, or as a specific daily capacity over the first 2 yr, next 4 yr, etc., or some similar projection. A good example of this kind of situation is Asarco's Mission operation 15 mi southwest of Tucson, Ariz., described by Weiss and Vincent.' where the major rock types differed widely in hardness, so that a change in the proportion of these types in the mill feed could have imposed difficult design problems if a constant tonnage rate had been expected. 28.1.2-EXPECTED LIFE The life of a mining operation depends upon the size of the deposit and the rate of mining. The latter is a policy decision based on an economic analysis which, in turn, is based on many factors.' From the point of view of mill planning, the estimated life of the operation determines many criteria and affects many decisions on strength of structures and degree of protection of men and materials, the quality of the materials-handling and process machinery, the type of delivery systems for ore to the mill and concentrates to the smelter or market, and many others. Costly installations that may be excellent investments for a 20-yr project may be wasteful for a 5-yr operation. An example is the comparison of different methods of crushing or grinding. Take single- vs. multiple-stage grinding-the former may be found more economical for a 5-yr operation, and the other, more costly, method more economical for a 15 to 20-vi- life.

Jan 1, 1973

By A. Wahab Khair

There are a number of factors, including mine geometry, local geology, geotechnical properties of overburden materials, surface topography, sequence of overburden strata, and extraction rate, affecting characteristics of surface subsidence imposed by large underground excavation. Among the factors, the first three have the major impact on magnitude and area of influence of final subsidence. Hence, a model has been developed, considering mine geometry and geologic and geotechnical properties of the associated area, to predict maximum possible subsidence and subsidence profile at any cross-section within the subsidence influence zone. Based on extensive field measurements and mechanics of strata behavior, under the action of overburden pressure in the vicinity of the large underground excavation, the vertical plane of influence zone has been divided into five areas: 1) excavated, 2) caved, 3) fractured, 4) highly deformed but continuous, and 5) subsided zones. In the final state of subsidence each area maintains a certain volume expansion/contraction, i.e. a factor which depends on geologic, geotechnical properties of overburden strata and state of stress within the subsidence trough. The cumulative volume expansion and contraction partially compensates for the extracted volume and the difference between the two is reflected as the subsided area in the form of the area within a curve defined by a probability function. The input parameters for the model are mine geometry (i.e. length and width of the panel), depth of cover, and geologic and geotechnical properties of overburden strata (i.e. percentage of hardrock, sandstone and limestone, and soft rock, shale within the overburden strata and Rock Quality Designation). The model calculates angle of draw for the site, expansion factor for each zone utilizing empirical relationships, maximum possible subsidence and plots the subsidence profile curve. The model is developed for a longwall excavation with unique characteristics of prediction of angle of draw and maximum possible subsidence for a given geologic and mining condition at any cross-section within the influence zone of subsidence.

Jan 1, 1986

By James E. Lonergan

Linear goal programming is a multi-objective optimization technique where the constraints of a linear programming formulation of a problem are considered as additional objectives. The optimal solution is the one that comes closest to satisfying all the objectives. An interactive computer program was written to utilize this technique in solving the feed blending problem faced by power plants de- pendent on multiple sources of coal supply. This program determines the amount of coal from each supplier to utilize in the blend. Examples of the use of the program in both long and short term coal procurement planning scenarios are given.

Jan 1, 1984

By C. A. Roberts

What are the benefits and limitations of financial analysis software as a decision making tool in the mining industry? Traditionally, the assumptions and simplifications imposed by complex and uncertain information have been viewed as the main obstacle to reaching an optimum decision. Recently, however, phenomena such as corporate culture and power structure have received increasing attention as significant influences on organizational decision making processes. Studies of these phenomena have suggested an alternative way of understanding decision making processes and an alternative view of the role played by computer analysis in such processes. This paper presents these two views of decision making, and examines what each implies about the role of financial analysis software as a decision making tool in the mining industry.

Jan 1, 1992

By William Gleason

The evolution of technology has made the world a more connected place. It continues to change the way we power our homes and vehicles and is leading to a future that seems to be limitless. Limitless as long as we can continue to supply the minerals necessary for technology to produce better iPhones, more efficient electric cars, better wind turbines and sophisticated national defense systems. These minerals, dubbed critical minerals, have surged in importance in every corner of the world and, on Aug. 3-4, they were topic of conversation at the Critical Minerals 2014 conference in Denver, CO. The conference, hosted by SME and the Australasian Institute of Mining and Metallurgy (AusIMM), looked at critical minerals from every angle, from where they are found to what the future might be. Among the minerals that have been called critical are rare earths, a collection of 17 minerals that have become increasingly important as technology continues to advance in everything from communications to energy to national defense. Leading off the conference, David Abraham, senior fellow at the Institute for Analysis of Global Security, explained that, like many people, he is relatively new to rare earths. Unlike most people, though, Abraham developed more than a passing interest in the minerals and has since travelled the world to understand the role of rare earths ? where they are found, how they are mined, how they get to market and, eventually, what applications they are used in. Following his travels, he said he returned concerned about the sector and how the industry will keep up with the demand that only seems to be growing in the modern world. And, Abraham noted, that it is not just the developed world that is driving demand. It stretches even to places like Indonesia, where the average annual income is about $3,000/year. Yet, the nation is one of the most active places in the world for social media with a population that is wired in with all kinds of electronics. The problem facing the sector is, and has been for a long time, and especially since 2010, supply of the minerals. At one time, China produced about 98 percent of the world?s supply and controlled the sector completely. In 2010, as the world began to demand more rare earths and develop other sources, China announced an export ban on rare earths. This changed the game completely, from the production lines all the way to the floor of the U.S. Congress.

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979