Search Documents

By John H. Bassarear

How best to grind? This article compares conventional crushing and grinding circuits to semiautogenous circuits, reviews recent installations of each circuit, and describes seven methods of using autogenous or semiautogenous techniques. In addition, steel and power consumption data are reported and benefits of a dedicated digital computer are discussed. Size reduction is the most expensive operation in most mills. Crushing and grinding are usually the greatest part of capital costs. They often make up 60-70% of total mill operating costs. Picking the proper crushing and grinding method must, therefore, be done with great care, so the best circuit is chosen. In the past 10 years, there has been a strong trend toward using autogenous or semiautogenous grinding in mills throughout the world. Autogenous grinding is favored when the ore is quite competent and a fine grind is needed. Semiautogenous grinding is applied when fine crushing could cause severe problems or when ore varies in hardness or competency. The taconite iron ores of northern Minnesota fit the description for an autogenously ground ore and many are successfully ground that way. Most im¬pressive are the nine lines of 11 x 4.9 m (36 x 16 ft) mills powered by 9 MW (12,000 hp) motors at Hibbing Taconite. Porphyry copper and molybdenum ores fit the description for semiautogenous grinding. Recent installations include Highmont in British Columbia, Canada, and Quintana in New Mexico. Sampling Many mills have been built based on inadequate sampling data or insufficient tests. With the cost of many mills exceeding several hundred million dollars, it is mandatory that geologists, mining engineers, and metallurgists work together to prepare representative testing samples. Simple, repeatable work index tests are usually sufficient for rod and ball mill tests. However, pilot plant tests on 50-100 t (55-110 tons) of ore are frequently necessary for autogenous or semiautogenous mills. Preparation and selection of the test sample is of utmost importance. Procedures for autogenous and semiautogenous mill pilot plant tests are relatively simple for those experienced in running them. Reliable and repeatable results can be obtained if simple, fundamental procedures are followed. The accompanying figure shows a typical conventional crushing-grinding circuit with three stages of crushing followed by ball mills or a rod mill-ball mill combination. This flowsheet is typical of many mills that have been built throughout the world. Also shown is a typical semiautogenous (SAG) circuit with feed coming directly from a primary crusher, and the semiautogenous mill product going to the separation process. Many similar semiautogenous circuits are built today because they are simple and flexible, lend themselves readily to high tonnages, and usually cost less to build and operate. With some ores, it is possible to send mine-run ore directly to the semiautogenous mill, eliminating the need for a primary crusher, as at Benquet's Dizon mill in the Philippines. An autogenous or semiautogenous circuit, as the name implies, uses the ore itself to assist in the grinding process. Generally, for this type of circuit, the ore must be competent so large ore chunks can be used to grind smaller ones. If ore alone is used, then the circuit is autogenous; but if balls are added to supplement the charge, then the circuit is termed semiautogenous. Ore competency is not always a criterion, to break up large pieces and wash away cementing material. Autogenous and semiautogenous mills have been very successful on relatively soft uranium ores where the values are frequently found in the material that cements together the sandstone grains. Autogenous Circuits When an ore is hard and competent, it is always possible it might make good "pebbles" that could be used for fine grinding media. Seven methods have been tried using combinations of autoge-

Jan 6, 1982

By Nathaniel Herz, R. J. Adamson, C. M. Romanowitz, Frank W. Jr. McQuiston, C. D. Hoyt, Robert S. Shoemaker, P. H. O’Neil

1. INTRODUCTION In this section, precious metals are defined as gold, silver, and the platinum group metals comprised of platinum, palladium, iridium, osmium, and rhodium. If the first three years of the 1970's are the criteria, gold, silver, and platinum seem destined for a bright future. Gold advanced in price from the historic figure of $35 established in 1934 to over $100 per oz (1973). For the five years 1966 to 1970, silver consumption exceeded production by about 50%. The silver price appears to be definitely on the uptrend, and a price of over $3 per oz seems probable. On this basis (at 1964 costs) the United States has an estimated 5 billion oz of unmined silver. The fresh burst of interest in platinum with a surge of renewed price strength (end of 1972) is due to the activity in the automobile emission control area, where platinum re¬mains the front runner in the catalyst area. Some international financial experts believe that governments will not rush into reform of the monetary system, and "Special Drawing Rights" (SDR's) will gain increased standing as international mone¬tary reserve assets. Gold will continue to be reviewed as the ultimate store of value and will remain the global monetary base. Devaluation of the U.S. dollar caused by imbalance of import payments over ex¬ports is the basic reason that the price of gold will likely remain above the $90 per oz figure for the balance of the 1970's. Gold and silver usually occur intimately associated, and recovery methods are often closely related; however, they were assigned sepa¬rate chapters, because the major production of each metal is from ore deposits classified as either gold or silver. For example, the gold ore occurrences in South Africa, the world's leading gold producer, have a ratio of gold to silver of approximately 10 to 1. The ores at the Homestake Mine, Lead, S.D., the largest U.S. gold producer, are predominantly gold with a ratio to silver of approximately 5 to 1. Silver in each example is a byproduct. By this same classification, the largest U.S. silver producers are the silver ores of the Sunshine, Galena, and Lucky Friday mines in the Coeur d'Alene district, Idaho. However, the largest single-mine silver producer in the Free World is the Kidd Creek Mine at Timmins, Ont., where the occurrence is with sulfides of copper, lead, and zinc. Thus, the major gold production of the world is derived from those ores classified as gold ores; whereas, less than one-half of the silver production is from silver ores, and only a small percentage of the silver production is from gold ores. 2. GOLD Gold, the noblest of metals, has been mined for thousands of years. Its chemical symbol, Au, is derived from the Latin "aurum," meaning "shining dawn." A precious substance because it is one of the rarest metals, it has unique physical properties: it does not tarnish; it exceeds all other metals or alloys in malleability and ductility; it is a good conductor of electricity and is one of the most nonreactive metals. Its greatest strength is its indestructibility. It is the only metal mined at depths exceeding 10,000 ft. Since the early 1800s, its chief role has been as a medium of exchange, providing the basis for interna¬tional trade. In the past 15 years, however, gold has emerged as a useful industrial commodity. This role has been fortified by the estab¬lishment of a two-tier pricing system which maintains monetary gold prices at an established U.S. Government price, with industrial gold being priced higher by the free-market system. Occurrences and Production Native gold furnishes most of the world's production, since gold forms stable natural compounds with few other elements. Neverthe¬less, the metal is widespread with traces of it found in seawater and in the ashes of plants and animal material. Next to the native metal, the tellurides have been the most important gold-bearing minerals; these include calaverite, krennerite, slyvanite, hessite, and nagyagite. Native gold is invariably alloyed with more or less silver, but it is exceptional to find any other metal in the alloy. It is found in veins associated with quartz, calcite, alunite, other gangue minerals, and with various sulfides. Sulfide minerals in order of frequent associa¬tion are: pyrite, galena, chalcopyrite, sphalerite, arsenopyrite, tetrahe¬drite, and pyrrhotite. Small amounts of metallic gold are commonly disseminated through such sulfides. When considerable amounts of silver occur in gold, the mineral electrum is formed. In a few deposits, gold and mercury form natural amalgam. Native mercury is formed by weathering from cinnabar and other mercury minerals. Among the minerals sometimes mistaken for gold, pyrite, marcasite, and especially chalcopyrite may be men¬tioned. The flakes of biotite and other micas, especially when partially oxidized, also may imitate it closely. World gold reserves never have been estimated carefully. Esti¬mates indicate that present world reserves approximate I billion oz, of which about 60% occurs in South Africa and 20% in the USSR. World gold output is dominated by South Africa which produces two-thirds of the world's production from reserves that are adequate to maintain existing output levels. South African gold output comes from approximately 50 large underground operations that mine and mill 70 to 80 million tons of ore annually to recover 30 to 32 million oz of gold. The USSR is the second largest gold producer, followed by Canada and the United States (see Table 1). Gold production in the United States and Canada rose to high levels in the 1930's, following the increase in price from $20.67 to $35 per oz and with an abundance of good labor due to depression in other industries. Production of over 10 million oz in 1940 was behind only that of South Africa. World War II caused a precipitous drop in gold output due to the imposition of War Production Board Limitation Order L-208 issued in October 1942, which caused over 9,000 gold mines in the United States to shut down, most of which never reopened. The U.S. Treasury, which suspended purchases of newly mined gold in 1968, had been the sole buyer of U.S. produced gold since 1934. This created the two-tier pricing system, and in March 1972 the President signed into law a bill authorizing a $3 increase in the official price of gold to $38 per oz. In February 1973 the President ordered a second devaluation of the dollar, amounting to about 10% which raised the official price to $42.22 per oz. The erratic development of the gold market, which has seen the

Jan 1, 1985

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

 The paper demonstrates that Belle Fourche Shale (BFS), an abundant shale, can be transformed into a ceramic through careful characterization and thermal processing. The study explores the potential of BFS ceramics for use as refractories and thermal energy-storage devices, highlighting their high thermal storage capacity, good thermal shock resistance, and cost-effectiveness.

Dec 1, 2023

By Hans Hamrin, Bruce Kennedy

Once an ore body has been probed and outlined, and sufficient information has been collected to warrant further analysis, the important process of selecting the most appropriate method or methods for mining can begin. At this stage, the selection is preliminary only, serving as the basis for a project layout and feasibility study. Later, it may be found necessary to revise the details, but the basic principles for the ore extraction should remain a part of the final layout. With respect to the basic principles employed, relatively few mining methods are used today. For the purposes of this presentation, the principles are classified as follows: 1) For naturally supported stopes, the available methods are room-and-pillar mining and sublevel stoping. 2) For artificially supported stopes, the available methods are shrinkage stoping, cut-and-fill mining, square-set mining, and longwall mining. 3) For caving methods, the available techniques are sublevel caving and block caving. Due to the uniqueness of each ore deposit, the variations on each of these methods are nearly limitless. It is impossible to include even the major variations in this chapter; the goal of this chapter is to present the principles as a guide to the mining engineer in adapting the general methods to specific needs. The selection process described herein is intended to supply the techniques by which the candidate methods available for a given ore body can be reduced to one or two feasible approaches. The feasible approaches then can be evaluated in detail, and the particular modifications can be investigated. In describing costs and economic factors, all values herein are expressed in terms of 1978 US dollars.

Jan 1, 1982

By A. B. Samaddar

A prototype automated mapping and spatial information management system has been developed, and illustrates how a powerful map manipulation capability and a comprehensive display system can be combined using both raster and vector mapping: The concept of a mapbase and information retrieval mechanism, query language as well as text and graphical menus, is introduced. The Geographic Information System (GIS), which has been built around a system for storage and retrieval of spatial and textual data, allows interaction with geographic space represented on a displayed map. The prototype is demonstrated using maps and information of an open pit mine.

Jan 1, 1989

By M. M. Hajdasinki

A project's rates of return (RORs)1, be it the internal rates return (IRRs) or one of the many IRR surrogates, frequently needs to be approximated. The success and efficiency an ROR- approximation procedure depend on the quality the approximation-initiating parameters, such as bounds or seed values (guesses). The existing approximation procedures commonly use bounds and guesses suggested by intuition rather than supported by mathematical considerations. This paper presents three mathematically founded ROR-bounding and eleven ROR-guessing approaches and examines their suitability by using examples of typical project cash-flowpatterns (CFPs). The calculated bounds and guesses not only improve the approximation efficiency, but also allow the process of the ROR discovery to be automated, thereby making it more convenient and reliable.

Jan 1, 1999

By Tzou-Shin Ueng

Rock reinforcement of rock anchors and rock bolts are commonly used for the support of large rock caverns. The rocks at the location of most large underground openings are usually under very high initial stresses prior to excavation. Hence, the stress redistribution caused by excavation will induce considerable rebound deformations of rocks surrounding the caverns. Since the pressures exerted by the reinforcement are generally far below the initial rock stresses, the reinforcement will be stretched along with the rock deformations, and the stresses in the reinforcement increase accordingly. It is not uncommon for the stress in the reinforcement to reach the yield strength, and in some cases the reinforcement may even have failed. Therefore, the increase of stresses caused by the rebound deformations of rocks should be taken into account in addition to the force required to stabilize the caverns. It was found that the measured stress increases of the prestressed tendons after installation were in good agreement with those computed based on the measured rock deformations between surface and the anchoring point of the reinforcement. The rebound rock deformations and the stress increases in the reinforcement can be estimated based on the results of the finite element analysis and experiences in previous field measurements incorporated with considerations of the geologic conditions, rock properties, rock reinforcement and construction procedures.

Jan 1, 1986

By Lane White

In conjunction with its 1993 Annual Meeting, held Feb. 15-18 in Reno, NV, SME sponsored a symposium, "Conveyor Belt Engineering for the Coal and Mineral Mining Industries." Eighteen papers were presented, grouped into four sessions: Low Tension Drives, High Tension Drives. Novel Techniques and Specifications. Three of the papers have been republished in this issue of MINING ENGINEERING. Brief summaries of the other 15 papers are presented here. (The 193-page symposium Proceedings, edited by Mike Evans of Consol, includes all of these 18 papers and is available from SME. For the convience of interested readers, an order form is included at the end of this Proceedings summary.)

Jan 1, 1993

By Floyd M. Thorman

Gypsum is the crystalline chemical compound CaS04?2H20. A close chemical relation - and frequently occurring with Gypsum ? is Anhydrite which is Cask. Gypsun has wide commercial use because relatively simple heat processing reduces it to Plaster of Paris. While Anhydrite can be converted to Gypsum and thence to Plaster of Paris, the procedure is not simple and is quite costly. Anhydrite, however does have use in the agricultural field and in the Portland Cement industry. Occurrence of Gypsum in the earth structure is usually near or at the surface. Most underground mining is at 60 to 100 feet although one mine in southwest Virginia reaches a depth of 1300 feet. Gypsum is one of our softest minerals, rating only 2.0 on the Mohs scale of hardness. Specific gravity is 2.3 to 2.4. It is soluble in water but only slightly so. Interestingly, it is more soluble in cold water than in hot. For example, one part Gypsum dissolves in 370 parts water at 106° Fahrenheit while at 212°F. the water requirement is 452 parts. Compressive strength of massive Gypsum runs about 3000 lbs. per square inch. Color ranges from grey and brownish-grey to white.

Jan 1, 1973

By Mustafa Akser

The Pipestone Lake anorthosite complex in Manitoba, Canada, was recently been re-identified as a potential source for titanium, iron, and vanadium. The present study utilized a 350 kg hard rock sample, which originated from the "Main Central" zone of the deposit. Commercial pilot-size equipment, such as dry low intensity roll magnets, wet high intensity magnets (WHIMS), and high tension electro-dynamic roll separators, was employed. As products, ilmenite up to 48.5% TiO2, and magnetite concentrates up to 87.9% Fe3O4 with 5.25% TiO2 were obtained. The majority of the vanadium reported to the magnetite concentrate. Subsequent characterization of various separation products shed light on the potential grade and recovery of the minerals from this deposit.

Jan 1, 1996

By Ronald S. Conti, Harry Dobroski

Re1iabl e monitoring a1ong an underground mine belt line is of great concern because of combustibles, electrical apparatus, and friction. Belt entries are strategically located where a fire can have rapid and disastrous consequences. This paper reviews conventional distributed temperature sensing systems based on resistive, thermistor, and thermocouple effects. These are shown to provide limited benefits. A new system tested by the U.S. Bureau of Mines based on fiber optics and time domain reflectrometry, promises much better temperature and spatial resolution, faster response, inexpensive cable, longer distance, and comprehensive data analysis. Test results in a small, controlled, in-mine fire are given.

Jan 1, 1992

By Xintan Chang

A computer software package, named CFIRE, for the general ventilation network analysis and fire control, mine fire and/or coal spontaneous combustion, has been developed at Xian Mining Institute in China. It is a multipurpose package with adequate capacities of ventilation map drawing, ventilation network analysis, gob fire simulation, steady state ventilation simulation and transient state ventilation simulation. It was written in a user-friendly style, driven by menus, facilitated by on-screen messages and supported by the allowance of user interferences. CFIRE has used up-to-date research findings focussing on the practical needs of coal mines. This paper discusses briefly also the relevant theoretical principles on which this package has been perceived.

Jan 1, 1989

By Kal V. S. Sastry, Stephen N. Little

Computer simulation of comminution systems is found to provide significant cost savings by enabling efficient circuit design and development of control systems. These simulation systems are based on sound mathematical models and numerical methods. Nevertheless, they are found to be hard-to-use and hard-to-modify to carry out more elaborate process analysis. This paper discusses the fundamental principles and practical aspects of an advanced, highly functional, and user-friendly SIMulator for COMminution, SIMCOM, that is being developed at Berkeley by incorporating state-of-the-art software engineering principles.

Jan 1, 1992

By Gordon B. French

The Occidental Oil Shale mining and retorting system for the production of shale oil has many advantages over the conventional underground mine and surface retort systems. For example only a portion of the oil shale is mined and transported to the outside, where it blends with the existing shale talus found on most of the slopes in the immediate area. The retorted spent shale is retained underground so that it does not become a surface disposal problem. The process consumes only minor amounts of water which is produced in adequate amounts in the retorting to fulfill all mining operations needs without outside supplies. Noise and dust levels are kept to a minimum with most of the facilities located underground. The exception being the generating stations and facilities as required to monitor air and water qualities, and last but not least, more than four times as much oil is pro¬duced from a given acre than from conventional surface processing. With the increased thicknesses as available on the government monopoly area this number could be increased by a substantial amount.

Jan 1, 1975

By J. Patrick Powers, Joel Miller, Arthur B. Corwin

A combination of a slurry trench with dewatering successfully controlled groundwater for a large sloped excavation immediately adjacent to the Arkansas River. The Murray Hydro Electric Project required excavation through sand and gravel to bedrock, 85 feet below high water in the River. The perimeter system of deep wells pumping up to 25,000 GPM (1,600 1/sec) lowered the water level to 15 feet (4.6 m) above bedrock. A short soil/bentonite slurry trench near the toe of the slope cut off the residual head. The method cut six weeks from the critical path. Design of the slopes and the dewatering system demanded high safety factors because of risk to existing Lock and Dam No. 7. A localized pocket of soft organic clay was supported by a rock filled bolster. A major flood event was successfully withstood. The method can be applied to large civil excavations and open pit mines.

Jan 1, 1989

By R. K. Paramguru, K. Srinivasa Rao

This paper describes a new approach for examining the kinetics and mechanism of zinc dissolution from sphalerite concentrate in acidic ferric sulfate solution in the presence of manganese dioxide. A literature search was performed to access the possible action of the two oxidizing agents, i.e., ferric ion and manganese dioxide. The possibility of galvanic coupling between ZnS and MnO2 and the cyclic action of the redox couple, Fe2+/Fe3+, on these two minerals were theoretically examined based on corrosion principles. Expressions for the mixed potential (Em) and the mixed current (im) were derived for the relevant corrosion and galvanic couples. Leaching experiments were conducted to establish which of the above phenomena is operative during leaching. The results indicated that the dissolution mostly occurs by the action of ferric ion on ins producing ferrous ions. The presence of MnO2 enables a quick conversion of ferrous to ferric, which maintains the rate of in dissolution. The process has promising features for commercial exploitation.

Jan 1, 1999

By Michael Prince

"Managing slurry is a constant challenge for mining operations. Since slurries are not uniform, the challenge is complicated by varying rheology, velocity, temperature and pressure, all of which affect how the slurry moves through the pipeline and how destructive it is to the system it is flowing through. Picking the right equipment from the outset — the right size pipe, the right size pump and the proper valves for the application — allows mines to operate more efficiently. Better valve designs deliver multiple benefits — they can lower the cost of operations, reduce the amount of maintenance and associated downtime required and are better for the environment. Historically, modulating systems have used ball, plug and pinch valves to manage the flow of slurry, but each of these alternatives has limitations. Ball valves require ceramic lining in order to delay wear, and once a ball valve does wear, the entire valve must be replaced. Similarly, plugs in plug valves should be coated to perform in control systems, and whole valves must be swapped out upon wear. Pinch valves are expensive and only require replacement of the sleeve. However, sleeve replacement involves an extremely arduous process in which the valve is completely taken apart.Traditionally, designers have avoided using knife gate valves (KGV) in modulating systems because KGVs have not been able to hold up under the harsh operating conditions. The throttling that is required in some of these processes rapidly fatigues conventional KGVs, rendering them useless and in need of replacement. Fortunately, innovative design changes have the potential to change established views.Breaking new groundRecognizing the need for improved components, Victaulic took on the challenge of designing a valve that could withstand abrasive slurry systems for a much longer period of time. The first step in this process was to talk to miners, maintenance personnel, process engineers and operators in the field about the limitations of current offerings and then determine design specifications for an ideal replacement.Many of the responses to these inquiries were very similar and reflected challenges with current operations; the primary objective was to find a valve that would be lighter and cheaper than the valves currently in use. In theory, a lighter valve would be easier to replace, and since replacements need to be performed frequently, a cheaper valve seemed like the right idea."

Feb 1, 2019

By Colin D. Jardine

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. A recent application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by the use of a "building block" approach to design and equipment selection. Details of this approach and the results obtained are described.

Jan 1, 1982

By L. M. Pero

The paper summarizes aspects of the recent literature on mineral development in the Third World. The emphasis is on publications covering agreements between host governments and mining companies.

Jan 1, 1985

By F. F. Peng, Z. Lu

Employing a combination of two types of polyelcctrolyte might become necessary to enhance both the settling rate of the flocs and the water clarity of a fine-particle suspension in a high-capacity thickening process. The sequence of addition, mixing, type and dosage of polymer all affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance, i.e., a high settling rate of the flocs and the deisired underflow density and overflow water clarity. The required performance can be achieved by either adjusting the pH prior to anionic polyelectrolvte flocculation or using a combination of polymer flocculant and coagulant (dual-polymer system). The dynamic thickening test results showed that only the approach using a dualpolymer system is capable of meeting the required performance. The effects of polvelectrolvte dosage, the sequence and numbers of polyelectrolyte addition, the feed concentration, the bed level and the rake speed on the settling rate, underflow percent solids and water clarity were studied in cylinder tests and in a laboratory dynamic thickening unit. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively using total suspended solids in supernatant, underflow density and capacity per unit of settling area per unit of time. The objective of this study was to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1999