Search Documents

By Philani Larrance Ngwenyama, Ronald CW Webber-Youngman

The survival chances of trapped miners in underground mines depend on how quickly they can be located and rescued post-accident. During entrapments, emergency rescue is highly desired but can be hindered by the lack of positioning information when a fit-for-purpose missing-person locator system is not available. Various types of missing-person locator systems are available to aid search-and-rescue operations. From the wide range of the available systems, selecting the most suitable one becomes the next challenge. The available systems have not been measured if they are fit-for-purpose or not, and to what situation. This study proposes user requirements that can be used as a guideline to facilitate the system selection process. These user requirements provide a framework for the design and development of a fit-for-purpose missing-person locator system. The user requirements can also be used for evaluating the performances of a particular system, predict its success, and also drive future research toward developing new technology to enhance the capabilities of the current systems.

Apr 1, 2024

By Steve Trussell, William H. Langer

"Arizona aggregate (sand, gravel and crushed stone) producers enjoyed more than a half a century of nearly constant growth in demand for aggregates. Approximately 80 percent of the aggregate produced in Arizona is sand and gravel, and 20 percent is crushed stone (U.S. Geological Survey, 2015). Figure 1 shows the generalized distribution of potential sources of sand and gravel (yellow) and potential sources of crushed stone (other colors described below). Black dots show locations of aggregate operations.Sand and gravel commonly is produced from modern river channels and terraces although some alluvial fans and high-level paleo-river terraces also serve as aggregate resources. The gravel clasts are a mix of rock types that reflect the types of rock in the source area of the rivers. Generally processed river gravels meet stringent specifications for highend uses.Crushed stone, which makes up about 20 percent of production, primarily comes from a variety of metamorphic rocks and light-colored intrusive igneous rocks such as granite (brown areas), dark colored extrusive igneous rocks such as basalt and scoria (rust colored areas), and carbonate rocks such as limestone or dolostone (green areas). Carbonate rocks are also used in the manufacture of cement and lime.Construction and aggregate production in ArizonaBecause aggregate producers have limited facilities for storing product, stockpile changes are insignificant compared to production. Therefore, demand or consumption of aggregate in Arizona is considered to be equal to production. Production figures used in this paper reflect shipments, sales or marketable production, including aggregate used by producers to make readymix concrete and asphalt. Production figures were reported by the U.S. Bureau of Mines from 1950 until 1995 and by the U.S. Geological Survey (USGS) since then. Production figures are reported voluntarily, and major operators are the primary source for these figures. Because many smaller operators do not report their production, the figures are conservative values that provide an approximation of aggregates production activity."

Jan 1, 2015

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995

By Charles D. Litton

Introduction The successful performance of a mine-wide fire detection system depends upon its ability to detect the presence of a fire rapidly and reliably. It should be sufficiently rapid so that there remains enough time to either safely evacuate a mine or successfully extinguish and control the fire or both. It should be reliable so that false alarms are minimized without sacrificing sensitivity or time response. Systems should also be durable enough to withstand the mine environment over long periods of time while maintaining a high degree of re1iability. Maintenance and calibration of the system should be simp1 e and not require the expenditure of excessive time and manpower to keep it operational. Sensitivity, reliability, and durability of mine fire sensors and their electronic support systems have been the subject of significant Bureau research within recent years. The bulk of this type of information, along with the reports from which the remainder of this paper is derived, can be found in the Bibliography. It suffices to say that there exist commercially available systems for use in mines. This paper addresses a strategy for the use of such sensors and systems. Many factors influence the design of a mine-wide fire detection system, such as the potential sources and modes of ignition, the types of combustibles involved and the quantities avai1able for fire growth and flame spread. Mine air ventilation influences the growth and spread of a fire and also serves to transport the products-of-combustion to other areas of a mine remote from the fire. Fire sensor alarm thresholds place limits on the sizes of fires that can be detected. The time to respond to a detected fire, either in terms of evacuation or control and extinguishment, place additional time constraints on the design of fire detection systems. These factors interact with each other, often in complex ways, and it is the definition and understanding of these factors and their interactions that hold the key to the design of adequate and re1iable fire detection systems. Our level of understanding of the problem has increased dramatically within recent years and it is the intent of this paper to discuss the progress that has been made and how the information can best be used to improve the level of fire detection in underground mines.

Jan 1, 1986

By Richard S. Ghent, Daniel G. Warnock

JOHN HAMRIC: Our next speakers are Richard Ghent, manager of environmental health and safety for CF Industries, Hardee Phosphate Complex, in Wauchula, Florida. Richard has 20 years' experience with environmental health and safety affairs. He has a bachelor of science degree from the University of South Carolina. With him is Daniel Warnock, who is supervisor of safety and training also at the Hardee Phosphate Complex. Daniel's experience is in safety programs and electrical training. Their presentation is "Regulations Versus Management Practice." RICHARD GHENT: Written procedures give structure to safety programs. At their best, they are brief and understandable to facility personnel and clearly identify roles and responsibilities. At worst, they attempt to recite the entire regulation they are intended to address. Some regulations, such as OHSA's Hazard Communication Standard, require employers to develop, implement, and maintain a written program. As written programs and procedures are developed, some basic questions arise: Is the program designed to achieve compliance with regulatory requirements or does management expect the program to go beyond compliance to some higher level of performance? Management may have difficulty in measuring and communicating performance expectations in safety. A facility with 4 million safe work hours does not suddenly become unsafe the day their safety record is broken. Generally, management expects safety programs to meet regulatory requirements and to protect the employer from enforcement actions and fines from regulatory agencies. Management also expects that safety programs will result in a safer work environment with fewer incidents, accidents, and near misses. But it is difficult to know when a safety program has succeeded. If the program is expected to go beyond compliance, what other standards should be included (e.g., ANSI standards, company management practices, lessons learned from inspections and audits, recommendations from safety committees, etc.) in the

Jan 1, 1998

By K. W. Harris, K. A. Perry

Underground coal mines beneath Black Mountain in the Harlan County district of the Central Appalachian coalfields have an extensive history of bump events, which yields an elevated probability for significant injury or fatality to underground miners. According to Mark (2009), Harlan County has had the greatest concentration of deep-cover retreat mining in the United States. Combined with the extensive multiple seam mining history, room-and-pillar coal bumps have had a disproportionate impact on coal operations in this region. The Harlan seam, one of the principal, economically recoverable coalbeds exploited beneath Black Mountain, has a significant burst history that extends into modern times. A numerical investigation using the LaModel software of 17 bumps that occurred at the same mine in the Harlan seam was conducted and used to create a calibration methodology which serves as the quantitative basis for current and future numerical efforts in an adjacent mine exploiting the same reserve. In addition to this numerical study, a qualitative assessment of the geologic factors that are believed to contribute to the bump potential was completed. Combined with stability prediction using the numerical basis, these geologic factors will be used for recognition of high bump potential areas with the goal of reducing the potential for future bumps, helping to ensure the highest level of safety and productivity for underground personnel.

Jan 1, 2016

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By C. A. Rowland

With the rapidly rising cost for electrical energy and the long range pre¬dictions for continued rising costs and even possible energy shortages, operation of rod, ball, autogenous and partial autogenous grinding circuits to efficiently utilize the power delivered to the mills will be demanded. This calls for a method to evaluate grinding circuit performance that is accurate, reliable and readily usable as an operating tool by supervisory, technical and operating personnel. Neither the Rittinger and Kick theories of comminution,(1) which preceded the Bond Theory by more than 50 years, had a mathematical means that could be used to predict and evaluate the performance of crushers and grinding mills used to comminute ores and rocks. This severly limited the practical use of these two theories, which were contradictory to each other. They have been superseded by the Bond Third Theory of Commnution.(1)

Jan 1, 1976

By Taghi Sherizadeh, Paul Brooks, Dogukan Guner, Samuel Nowak

Large excavations are well known to result in rock mass deformations which can present challenging situations for mine personnel. Most of the currently available ground movement monitoring devices fail to adequately provide mine operators with highly accurate and meaningful insights into rock mass deformation or displacement. The use of distributed fiber optic sensors (DFOS) in industries such as oil and gas and civil engineering has shown the potential of these sensors to deliver real-time, highly accurate, and long-range distributed strain measurements with great success. However, the use of these sensors in underground mining is limited to a few case studies.

By T. Ruff, J. Steele

The lack of visibility near earthmoving equipment results in an average of five fatalities in U.S. surface mines each year. These accidents occur when a piece of equipment either strikes another vehicle or worker, or travels over the edge of an embankment. Researchers at the National Institute for Occupational Safety and Health have evaluated off-the-shelf proximity warning systems that sense obstacles near the equipment and provide an alarm to the operator. Limitations of existing systems have necessitated the development of new systems designed specifically for mining equipment, including a GPS-based proximity warning system and a computer-assisted stereovision system.

Jan 1, 2004

By N. T. Cowper

Slurry viscosity ultimately affects the majority of mineral extraction processes. However, to date its role has been disguised because mineral processing equipment has been conservatively designed to operate at minimal slurry viscosity. With most ores this still meant acceptable solids concentration was achieved. However, with the advent of treatment of weathered ores the resulting higher slurry viscosity (rheology) has meant solids concentration has had to be reduced, often to unacceptable levels. To permit operation at higher solids concentration chemical dispersants are employed. These dispersants are expensive and their addition should be controlled. Slurry Systems Pty Limited (SSPL) has developed an On-Line Viscometer to monitor and control slurry viscosity, whether by controlling water addition or by controlling dispersant addition. Using this instrument the slurry rheology can be controlled at the optimum level, maximizing solids throughput, and minimizing water, reagent, and dispersant addition. This paper discusses rheology of typical mineral slurries, the relationship between slurry rheology and percent solids in a slurry, and the need for rheological control in mineral processing. The effects of rheology on various process steps, and the use of dispersants are reviewed. The paper concludes with summarizing actual case histories and cost impact of Theological control.

Jan 1, 1992

By Y. C. Kim

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that Ordinary Kriging (OK) cannot easily handle. With the recent introduction of the nonparametric, distribution-free technique of Indicator Kriging (IK), the above problems can be solved. This paper describes the results of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blast hole information. The IK estimator, although a bit optimistic, performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion. OK was found to be very biased and pessimistic.

Jan 1, 1986

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer studies as well as for studies conducted in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources has been previously demonstrated in underground mines, but this new work details the testing of multiple, distinct tracer compounds compatible with passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed: (1) PMCH, (2) perfluoroethylcyclohexane (PECH) and perfluoromethylcyclopentane (PMCP). The release rates of these tracers were examined over a 180-day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in characterizing ventilation circuits, flow through gob and leakage. IntroductionThe use of tracer gases for ventilation applications is an established practice, with various past research projects conducted using sulfur hexafluoride (SF6). Tracer gas techniques have been applied to assess flow rates, dilutions rates and auxiliary ventilation system efficiencies with quick, reliable and accurate results (Suglo and Frimpong, 2002). Perfluorocarbon tracer (PFT) compounds are a new introduction to ventilation and air modeling applications in terms of ventilation flow characterization (Watson et al., 2007).PFTs are liquids that are characterized by low background presence in air, low reactivity, high detectability and low toxicity. A design was proposed, called a permeation plug release vessel (PPRV), to convert PFTs from a liquid to a gas and then release the gaseous tracer in a controlled manner. The initial concept was originally introduced by Brookhaven National Laboratory and refined later to become the PPRV. The PPRV functions by allowing the volatile PFT liquid to become a vapor in a controlled manner. The vapor diffuses through a permeable silicone stopper at a predictable rate proportional to temperature (Zhang and Cloud, 2006)."

Jan 2, 2018

By Alexander N. Winchell

"Location: The Menominee district has been described geologically in several units, because the known iron-bearing formations of the larger region are not a really connected. From the commercial and mining standpoint, however, the district em¬braces, all that territory extending from a point about five miles east of Vulcan to a point a few miles west of Iron River, an east-west distance of about fifty miles, and from a line about two miles south of Vulcan to one ten miles north of Crystal Falls, a north-south distance of about thirty-five miles. This area is largely in the State of Michigan, but includes more than two hundred square miles in Florence County, Wisconsin. The chief towns of the district are Vulcan, Iron Mountain, Iron River, and Crystal Falls, in Michigan, and . Florence in Wisconsin. The Wisconsin portion of the district has not produced a large portion of the output of the area.History: The earliest reports of iron ore in the Menominee district were made by J. W. Foster and S. W. Hill, who conducted a geological exploration from Lake Superior to Green Bay in the fall of 1848. It is a remarkable fact that in spite of their plain statements regarding their discoveries, these state¬ments were apparently forgotten for a period of nearly twenty years. Foster states that ""about two miles southeast of the lower falls (of the Twin Falls on the Menominee River) near Sec. 30, T. 40 N., R. 30 W. there is a large bed of specular iron ore associated with the talcose and argillaceous slates. It makes its appearance on the north side of the Lake and can be traced a mile and a half in length and in places is exposed one hundred feet in width."""

Jan 1, 1920

By C. Beul, R. Schipper, L. Santisteban

The Garfield Mine is a legacy vanadium mine in western Colorado with multiple mine openings, waste rock piles, and adit seepages that Cyprus Climax Metals Company (a Freeport-McMoRan Inc. subsidiary) voluntarily remediated through the Colorado Voluntary Cleanup Program (VCUP). The process to obtain a No Further Action determination from the VCUP is presented. Water treatment of the adit discharge, which is not part of the VCUP, is also presented. The remedial action objectives (RAOs) included preventing direct human or biotic exposure to the waste rock and radiation emitting from the waste rock; reducing metal concentrations and radionuclide activities in adit discharge and keeping the discharge from leaving the site; maintaining the existing undeveloped character of the surrounding landscape; and eliminating the need for a stormwater permit. The design included regrading, installation of an infiltration barrier and rock cover, a diversion channel, and a biologically based passive remediation water treatment system. An initial lab-scale evaluation provided design criteria for the full-scale system, which consists of a sulfate-reducing biochemical reactor and post-treatment aerobic polishing cells. The system has been operational since construction was completed in late 2016. Results indicate that the treatment objective of 90% bulk removal of constituents of potential concern (COPCs) is largely being met. The system also provides year-round operation and non-point discharge of effluent. After 20 plus years of site investigations, the remedial action was completed in 2016 with all RAOs met and a No Further Action determination granted in 2018. INTRODUCTION The Garfield Mine is a legacy vanadium mine located approximately 11 miles north-northeast of Rifle, in Garfield County, Colorado. It was leased and operated intermittently from 1929 to 1975 but was never operated by Cyprus Climax Metals Company (Cyprus) (a Freeport-McMoRan Inc. subsidiary). Prior to reclamation, site features included: • six mine openings—five adits and a vertical opening; • two adits discharging mining-influenced water (MIW)— Adit 1 at less than 4 liters per minute (L/min) and Adit 2 at 7 to 10 L/min; • main waste rock pile (13,500 m3) and small waste rock pile (minimal volume); • debris (small structure, mattress, bottles, shells, etc.) indicating site used for recreational purposes; and, • unimproved road, which has been used to access forest fires.

Jan 1, 2019

By Byron R. Berger

Epithermal Ag-Au deposits form at low to moderate temperatures in near-surface environments. Historically, these deposits have been the source of high-grade ores. Increases in the market prices for gold and silver make lower-grade ores economically viable when available in large tonnages. Both the high-grade and bulk-tonnage ores are a consequence of the same processes, and general models of epithermal systems can be useful in the search for new precious-metal resources. A detailed study of deposits at Round Mountain, Nevada; Balei, Russia; Creede, Colorado; Guanajuato, Mexico; and Chanarcillo, Chile, indicates that the hydrodynamics of the fluid systems as determined by fracture geometries, the permeability, and composition of the host rocks are the key factors in the creation of both high-grade and bulk-tonnage epithermal deposits. End-member models that explain the range of observed deposit characteristics are: (1) the hot-springs deposition model; (2) the stacked-cell convection model (where mineral deposition occurs laterally along the interface of two partially separated fluid reservoirs); and, (3) the closed-cell convection model (where deposition occurs in vertical zones due to the relatively unimpeded vertical flow of hydrothermal fluids). Boiling and fluid mixing appear to be agents of precious-metal deposition with the self-sealing of the hydrothermal system being an important adjunct to boiling. Imaginative application of model concepts in exploration has led and can lead to the discovery of new high-grade and/or bulk-tonnage precious-metal deposits.

Jan 1, 1982

By D. Tepavac, S. Simmonds

"The high virgin horizontal in situ stress field in the Sydney Basin and its impact on civil engineering projects is a well-known and accepted phenomenon found in significant literature (e.g., Pells, 2013). The prevailing high-stress effects depend on many factors — rock quality, tunnel orientation, proximity of geological features to tunnel crown, size and shape of opening, depth of excavation and stress magnitude. The behavior of the rock mass under high in situ stress conditions can cause stress fracturing and consequent dilation of the tunnel periphery, resulting in rock spalling at the tunnel crown/ invert or raveling of rock blocks on the tunnel sidewall. This type of failure is of a brittle nature and may create construction and safety risks during tunnel excavation, if it occurs behind the excavation face where ground support has already been installed. Therefore, the associated risks need to be managed during construction. This paper presents the design strategy adopted to mitigate these adverse tunneling conditions for the WestConnex Project to-date. Overview of the WestConnex M4 East and new M5 tunnel projectsWestConnex is one of the New South Wales government’s key infrastructure projects. This 33 km (20.5 mile) project aims to ease congestion and connect communities and is the largest integrated transport and urban revitalization project in Australia. It was a key recommendation of the State Infrastructure Strategy released in October 2012. It brings together a number of important road projects, which, together, form a vital link in Sydney’s Orbital Network. These road projects include a widening of the M4 east of Parramatta, a duplication of the M5 East, and new sections of motorway to provide a connection between these two key corridors. The WestConnex project includes a number of stages: Stage 1a: M4 Widening; Stage 1b: M4 East; Stage 2: New M5; and Stage 3: M4–M5 Link. The tunnel design referenced in this paper relates to Stage 1b and Stage 2 of the WestConnex Project (Fig. 1)."

Dec 1, 2018

By O. J. R. Baena

Mining activity in the Segovia region in NE Colombia is the main source of employment in the local economy. This has created major problems of illegality and informality mining associated with a high social and environmental impact, as inefficient technologies are used and high consumption of toxic substances required in the process of gold recovery by amalgamation and cyanidation. In this work is presented mineralogical characterization of six local mills and studied beneficiation processes developed in them. With the results presented a proposed plant design that eliminates the use of mercury by replacing gravity concentration processes taking advantage of the characteristics of the treated material. Significant results were obtained regarding the recovery of precious metals and present a methodology that can be replicated in other mineral beneficiation plants that use gold amalgamation processes. This implies a significant reduction in mercury use and decreased risk of human contamination associated with this.

Feb 23, 2014

By F. G. Miller

To improve coal flotation Bethlehem Steel Corporation's Research Department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies5 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the bas is for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14M x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level.

Jan 1, 1968

By Marc E. Orman, Mark E. Smith

Regulatory and environmental concerns continue to broaden the range of mine wastes that must be capped with low permeabili­ty liner systems at closure. The mining industry has been a leader in developing liner technology for leach pads and tailings impoundments, but it is a newcomer to cap designs. Closure of waste piles, leach heaps and tailings require special design con­siderations. Factos such as differential settlement, surface ero­sion, veneer stability, vegetation and burrowing animals must be considered.

Jan 1, 1996