Search Documents

By J. D. Patsey

A computer program has been developed for use by the mining engineer for analyzing drum-type hoists prior to the modification of an existing system or the designing of a new one. Its use permits the preliminary evaluation of a system before seeking the technical assistance of mine hoist designers and manufacturers. Compatible with an IBM-PC, the user-friendly program accepts a variety of data and can analyze hoisting systems for any balance state. The extensive program can be used to: (1) calculate skip capacity to yield a desired production rate; (2) solve for required drum face width; (3) select a permissible wire rope from a menu of 50 available rope types: (4) estimate total horsepower of the hoist plant; and (5) estimate power cost. An example of the model's use in evaluating a hoisting system will conclude the paper.

Jan 1, 1986

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992

By R. M. Yeates

Public concern over possible degradation of groundwater resources has resulted in an array of Federal laws and corresponding state laws to regulate contaminates from solid and hazardous waste. A mine owner must be familiar with environmental regulations which could impact his operation and must know what precautions and corrective actions to take in order to protect his mining operation from potentially expensive remedial actions. The Environmental Protection Agency (EPA), has issued few regulations controlling the management of mining wastes. Federal regulation of mining came primarily under the Surface Mining Control and Reclamation Act (SMCRA) administered by the Office of Surface Mining (OSM). Waste generated from the extraction, benefication and processing of ores and minerals was exempt from regulation under the Resource Conservation and Recovery Act (RCRA), which is EPA's major instrument in controlling surface contaminates. On December 31, 1985, EPA submitted to Congress a report entitled "Wastes from the Extraction and Benefication of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium Mining and Oil Shale", which will be referred to, henceforth, as the Congressional Report. This Congressional Report assessed the possible adverse effects of mine associated wastes. This report is the first step toward developing regulations with which EPA can regulate waste from the extraction, benefication and process of mineral ores.

Jan 1, 1987

By Lynn B. Hales, Randy A. Ynchausti

Because of the high economic value associated with small improvements in the operating performance of mineral processing plants, innovations in instrumentation, stabilization and expert control systems have been an ever-present part of the landscape in plants throughout the world since the I 960s. Expert control systems are computer programs that continuously monitor plant conditions; contain "expert knowledge" concerning the process, equipment and operational knowledge; and make timely recommendations for new process set points or even directly change the process set points to achieve desired management goals. Early rudimentary expert control systems first appeared in the early 1970s. They have grown from small, experimental but ambitious projects in which single unit operations were controlled to plant-wide systems that include technologies used in the U.S. space shuttle program. Experiences and results of applying these systems throughout the world will be explained discussed and analyzed. Typical results will be outlined and the use of expert control in the future will be projected.

Jan 1, 2000

By Andrew Cushing, Joe Carvalho, Jon Hurt

"INTRODUCTIONThe shales of the Greater Toronto Area (GTA) have been known to experience time-dependent deformations (TDD); those initiated by excavation-induced stress relief which progress with time as a function of rock porewater salinity, access to freshwater (or air) of lower salinity, clay and calcite content, and the buildup of swelling pressures within the rock mass. These deformations can induce long-term pressures on shaft walls and tunnel linings, especially if the permanent works are constructed soon after excavation, with very little time delay. This paper presents measurements of time dependent deformation of recent shaft and tunnel projects constructed in the GTA, and draws conclusions regarding the main influences on the TDD. The key input parameters for the numerical predictive model are critically assessed. Projects which are discussed include the Billy Bishop Airport Pedestrian Tunnel, Hydro One Midtown Tunnel and Hanlan Feedermain (Contract 3).MECHANISM OF TIME DEPENDENT DEFORMATIONExplanation of MechanismThe Georgian Bay Shale unit consists of typically moderately weathered to fresh, grey to dark grey, fine to very fine grained fissile shale interbedded with slightly weathered to fresh grey, fine grained calcareous siltstone and limestone interbeds. There are two distinctive features of the shale in the Greater Toronto Area (GTA). One is a high horizontal stress regime, and the second is long-term time dependent swelling behavior which develops when the following factors occur (Lo and Micic, 2010):• Stress relief of the rock mass• Outward salt concentration gradient from pore fluid of the rock to the ambient fluid• Availability of fresh waterThe swelling is a consequence of the reduction in confined stress in the rock which occurs upon excavation in combination with a differential gradient in salinity between the saline rock porewater and freshwater or even humid air. Osmotic and diffusive processes result in a decrease in the salinity of the rock porewater achieved by an overall increase in the water content, resulting in volumetric expansion of the shale rock over time. The development of this time dependent deformation (TDD) relative to the time"

Jan 1, 2016

"Replacing the century old rail tunnels that run beneath the Hudson River and carry about 200,000 passengers per day between New York to New Jersey has been a high priority for many years. But after Superstorm Sandy hit the east coast of the United States in 2012, the urgency to replace the tunnels increased dramatically. The Hudson Tunnels project is one of nine projects that make up the larger $30 billion Gateway Project. The Gateway Project has been called the most urgent infrastructure program in the country and the Hudson Tunnels is the most critical part of the project, as it will build a new rail tunnel under the Hudson River and rebuild the existing and deteriorating North River Tunnel that connects New York and New Jersey.“Superstorm Sandy proved the level of resiliency of the tunnels, which was not very good,” Amtrak deputy chief engineer structures James Richter told attendees of the George A. Fox Conference in New York City on Jan. 23. Age and corrosive salts deposited by flood waters from the storm in 2012 have affected interior concrete and copper wiring in the tunnels. “Since then, things have been deteriorating and getting less reliable.”Richter, along with Mohammed Nasim, senior director engineering design, both with Amtrak, spoke at the 2018 George A. Fox Conference where more than 350 tunneling and underground construction professionals attended the conference at the Graduate Center of the City University if New York to share insights about the complexities many of them face on daily basis.Under the theme of “Managing construction of complex underground projects: Strategies for tunneling in populated areas,” the one-day conference featured presentations from some of the top minds in the tunneling and underground construction industry. The presentations touched on everything from the highly technical challenges of constructing tunnels through changing geology while working beneath cities and rivers, to navigating the complex financial issues and contracts that come with the projects that have many stakeholders.All of those challenges, and more are part of the Hudson Tunnels project. It is one of the best examples of the full complexities of a complex tunnel project, with the added pressure of securing funding from state and federal government entities under an increasingly tight deadline."

Jan 3, 2018

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By David Butts

Completion of a railroad to the high Tibetan Plateau in Central China has now made it economical to exploit its mineral reserves. Lead and zinc mines are now being established. A potash plant to produce 40,000 tons per year KC1 is now in operation. Plans to produce 200,000 tons per year by 1987 are being implemented. Pilot drilling for oil and natural gas have proved up reserves. Slaughter houses are being constructed to ship yak, mutton and beef from the endless grasslands on the plateau. Research Centers in Xining and Golmud have been completed for the sole purpose of increasing technology and exploitation of the Tsaidam Basin and surrounding area.

Jan 1, 1984

By G. Vijaya Kumar, B. Srinivasa Rao, G. V. Krishna Rao

The paper outlines the ventilation practices prevailing in coal mines of Singareni Collieries Company (South India). The high annual average surface temperature and relatively steep geothermic gradient results in virgin strata temperatures in the region of 38- 42°C creating environmental problems in the working places. Expensive methods of air cooling can not be employed as the mines are small, and production and productivity do not justify the costs of artificial cooling of mine air. Controlled recirculation of mine air -- the unconventional technique being tried with success in some coal mines in U.K. has been analysed for improving the environmental conditions. The analysis shows that the method is safe, cost effective and can be applied with very little extra equipment.

Jan 1, 1991

By Mo Wanqiang

Equivalent-pressure ventilation is a method of balancing the air pressure between a productive face and its gob to extinguish fires and prevent the infiltration of toxic gases, so that the production of the face can be maintained. The method was successfully applied in Coal Mine No. 1 of Hebi Coal Mining Administration in north-central China. In this article, a practical application of the equivalent-pressure method to prevent carbon monoxide from entering an active longwall face adjacent to a fire breeding area is described, and four steps to achieve equivalent-pressure are discussed. The reliability of using this method and measures to maintain the equivalent-pressure are analyzed. It was observed that this method could maintain high production level while no sacrificing safety at the longwall face.

Jan 1, 1984

By Robin P. Gardner

The mechanistic approach to comminution consisting of incorporating particulate breakage functions into a suitable population balance equation has been developed by a number of researchers over the past decade or so. (1) To date this approach has been developed and demonstrated primarily for batch-operated, laboratory or small-scale ball mills. However, since industrial mills are mostly quite large and operated in the continuous mode; suitable population balance models and methods for obtaining the necessary breakage and other model parameters must be developed. This paper describes and investigates a radioisotope tracer technique for this purpose, Population balance models previously developed(2,3) are adapted for this study.

Jan 1, 1974

By Robert M. Dreyer

Thirty years ago it was possible to locate a quarry site for crushed rock for concrete aggregate by finding the nearest solid rock bluff accessible by road, But times have changed and the location of a quarry site to furnish crushed rock for concrete aggregate now has become rather complicated, Although both sand and gravel can be used for aggregate, this discussion will be confined to crushed rock in the regions around a metropolitan area. Let us assume that a consultant has been retained to advise on the desirability, and the possibility, of opening a new quarry within a given area. The problems are geological and ecological. Since the geological problems are simpler, they will be discussed first. Generally, the first step is to make a market study of competitive aggregate sources within the projected area. Assuming that the quality of aggregate to be sold by competitors as well as their mining costs will, within narrow limits, be the same, the problem becomes essentially a study of haulage costs from established quarries into the projected new area. Since haulage cannot be effected along straight lines and since each quarry operator may have different unit haulage costs, a map showing lines of increasing cost intersecting points on roads available for truck haulage radiating from competitive quarries can be rather complicated. Such a map, more-over, changes each time a new haulage contract is negotiated by a

Jan 1, 1971

By A. C. Nixon, A. D. S. Gillies, Hsin Wei Wu

Ventilation and refrigeration strategies for the 3000/3500 orebodies, Mount Isa Mines, Australia were reviewed. The orebodies lie between 1,200 and 1,800 m below surface and are characterised by steep geothermal gradients, intensively mechanised stoping methods and high ambient air temperatures in summer. Providing acceptable working conditions under these situations is difficult and costly. The ventilation air quantity required in the 3000/3500 orebodies exceeds 550 m3/s when the production rate is greater than 2.5 million tonnes per year. The maximum quantity that can be supplied and exhausted using the existing intake and return ventilation system is estimated at about 630 m3/s. For production rates greater than 3 million tonnes per year, either new intake and return airways will need to be developed or innovative approaches such as controlled partial recirculation used. A description is given of technical and economic investigations conducted at Mount Isa into controlled partial recirculation. During these investigations, a major field trial of a controlled partial recirculation system was undertaken with results indicating that an acceptable working environment can be achieved practically and economically utilising this approach. The cost involved in controlled partial recirculation for supplying the required ventilation quantity when the production of 3000/3500 orebodies exceeds 3 million tonnes per year is examined. A cost comparison between recirculation and other conventional alternatives such as new surface shaft or underground booster fans is included. The results indicate that the option of a new surface shaft will incur a high initial capital cost and moderate annual operating costs. The alternative of underground booster fans will necessitate a moderate capital cost and very high operating costs. Controlled partial recirculation, in this case, offers both the lowest capital and operating costs of the three options evaluated.

Jan 1, 1995

By Steven W. DeCou, Marcus R. Jensen, Stephen Navin

The Lake Mead Intake No. 2 is a project constructed for the Southern Nevada Water Authority which includes a 12-foot diameter lake tap and intake shaft constructed in over 225 feet of water; 1650 feet of 16x14-foot horseshoe-shaped tunnel leading to a forebay that is 165 feet long, 35 feet tall, and 30 feet wide; twenty-two 4-foot diameter steel lined well shafts extending 325 feet from the ground surface to the forebay; 3500 feet of 12-foot diameter pipeline crossing a bay in Lake Mead that has water depths of up to 80 feet; and 2700 feet of 9-footdiameter steel-pipe-lined tunnel. Major site grading for a future pumping station in the area above the forebay is also included as part of the project. The project is on the schedule’s critical path for completing the first phase of a $2 billion water supply program for the Las Vegas Valley. In this paper, the owner, the designer and the construction manager present a discussion of the risk management strategies that were used to control costs, minimize project delays, and facilitate problem resolution. The discussion includes an assessment of the effectiveness of the risk management strategies in meeting these objectives. This paper will be of interest to owners and engineers planning underground projects, especially those projects that present unique risks during the construction phase.

Jan 1, 1999

By M. N. Chandraprabha

This paper discusses the role of the mineral-adapted acidiphilic microorganism Acidithiobacillus ferrooxidans in the beneficiation of arsenopyrite-containing multisulfides (pyrite and chalcopyrite) and the bioremediation of the resulting arsenical waste water. It was found that adaptation to minerals alters the surface properties of the microorganism. Bacterial adaptation to arsenopyrite and controlled bacterial adhesion to mineral surfaces lead to selectivity in arsenopyrite separation. Bioremoval of arsenic ions (both arsenite and arsenate ions) by Acidithiobacillus ferrooxidans is also discussed. Key words: Acidithiobacillus ferrooxidans, Bioremediation, Arsenopyrite beneficiation

Jan 1, 2009

By Joseph W. Mullan

The today status of air pollution control legislation and regulations can best be described as an exaggerated state of environmental limbo. The '70's began but one and one-half months ago yet it already has been very appropriately named "the decade of the environment." This certainly will be the decade for new legislation - new regulations and hopefully "Clean Air." Already Washington is faced with legislators playing "pollution politics" to the crowds. Students have redirected their efforts from Vietnam to the cleansing of the environment and everyone including the man on the street has become an environ¬mental expert. This is the decade we all face, but where are we today? Pollution is not a new problem. It has been with us for centuries and while much is left to be done, much has already been accomplished. I will try to make some comparisons of what I believe to be the good and bad points in the national air pollution control picture and hopefully will generate within each of you sufficient concern as to which comparisons are sound.

Jan 1, 1970

By David Wilson, T. V. Rao

INTRODUCTION The Alchem trona mine, owned and operated by Allied Chemical Corp., is located approximately 32 km (20 miles) west of the town of Green River, and 8 km (5 miles) north of Interstate 80 in southwest Wyoming. Trona, a naturally occuring sodium sesquicarbonate (NaCO3 • NaHCO3 • 2H2O), is used for the production of sodium carbonate (Na2CO3), commonly known as soda ash. Present annual US consumption of soda ash is approximately 9.07 Mt (10 million st), out of which approximately 7.3 Mt (8 million st) is produced from the Wyoming trona mines. About 44% of soda ash is consumed by the glass industry; 3 % by exports; and the remaining portion by paper, chemical, soap, textile, and nonferrous industries. Allied Chemical operates an underground mine at an average depth of about 488 m (1600 ft). There are three other trona mines in the area operated by FMC Corp., Stauffer Chemical Corp., and Texasgulf Inc. (see Fig. 1). Allied Chemical became interested in southwest Wyoming trona deposits in the early 1940s. Explora¬tion work was begun in 1959 with the acquisition of federal leases. Exploitation of the reserves began in 1968. Two shafts, one 6.1 m (20 ft) and another 3.7 m (12 ft), were completed prior to 1968. The 6.1-m (20-ft) diam service shaft is divided in half by a cur¬tain wall, with one half used for men and material and the other for ventilation as a return air shaft. During the period from 1968 to 1974, the 3.7-m (12-ft) shaft was used as production shaft with two 7.3-t (8-st) skips. Due to the increased demand for soda ash, plant and mine expansions were completed during 1974. Under this expansion, the material handling system capacity was increased by constructing a new 2721-t (3000-st) capacity ore bin, sinking a 6.1-m (20-ft) diam produc¬tion shaft, and installing a friction hoist with two 22.7-t (25-st) skips. The Alchem mine manpower is 484 employees and about 2.3 Mt (2.5 million st) of trona was produced during 1976. Three different mining systems are used at the Alchem mine: conventional, continuous, and longwall. Allied Chemical introduced its first longwall unit in 1973, which was also the first longwall system introduced in the Wyoming trona district. At present, four conventional, seven continuous, and two longwall units are in operation. This equipment is operated in ten production areas. GEOLOGY The bedded trona and trona-halite in the Green River basin of southwestern Wyoming is a major re¬source for the nation. There are 25 beds that exceed 0.9 m (3 ft) in thickness and underlie areas of about 2590 km2 (1000 sq miles). There are other minor beds that range in thickness from 0.3 to 1.2 m (1 to 4 ft). Allied Chemical's Alchem mine is located in bed 17. The trona bed numbering system starts at the lowest elevation and increases upwards. The trona beds are in the Wilkens Peak member of the Green River formation. The Green River formation was deposited in a lake that began in early Eocene as a large body of fresh water, shrank in size and became saline, and then became fresh water again. The sedi¬ment during the saline phase of the lake, which includes the trona beds, is called the Wilkens Peak member. The underlying freshwater lake deposit is called the Tipton member and includes a 25.9-m (85-ft) sand unit which is a high pressure, low permeability aquifer. The over¬lying sediment is called the Laney shale. The Green River formation is underlaid by the Wasatch formation and overlaid by the Bridger formation (see Fig. 2). The structure of the beds in the area of the Allied Chemical mine is mostly postdepositional asymmetrical folds of small amplitude. These folds range in size of 3 to 6.1 m (10 to 20 ft) to as much as 45.7 m (150 ft). The trend of the folds is northwesterly with the north¬east flank of the anticlines having a steep dip and the southwest having gentle dips. Trona bed 17 varies in thickness from 2.4 to 3.4 m (8 to 11 ft) over the 93.2 km2 (36 sq miles) holdings of Allied Chemical and is flat lying except for the rela¬tively minor folding and a negligible regional dip of about 0.017 rad (1°). Trona occurs naturally in several physical forms in the Green River basin, being both massive and crystal¬line. The trona ore in the Alchem mine is a fine-grained massive ore with a compressive strength of approxi-

Jan 1, 1982

By Guy Bridges, Elton Ko, Cheng Ting Ning, Owen Ng, Giovanni Chang, Robert Anderson

"PROJECT OVERVIEWThe Liantang/Heung Yuen Wai Boundary Control Point (BCP) and Associated Works will be the seventhland crossing between Shenzhen and the Hong Kong Special Administrative Region (HKSAR) of China.The project includes site formation of about 23 hectares of land for the development of the BCP and anapproximately 11-kilometre (km) long dual two-lane trunk road (the “Connecting Road”), connecting theBCP with the existing Fanling Highway. The route alignment is within a relatively rural area of HongKong, with very limited similar infrastructure works carried out nearby. It passes beneath bothmountainous terrain, and alluvial plains, and falls within an area of several major regional faults andassociated metamorphism, resulting in a complex variety of ground conditions.ALIGNMENTThe Civil Engineering and Development Department of the Government of the Hong Kong SpecialAdministrative Region carried out extensive public engagement in selecting the alignment of theConnecting Road. Over 70 consultation forums with public bodies, including the District Councils, RuralCommittees, local representatives, etc. were held during the alignment design process. In order toalleviate the concerns of various nearby villages, and to minimize land clearance and environmentalproblems, the original alignment of 10 km long (3.5 km of tunnels and 6.5 km of viaducts) was revised toits final alignment of 11 km long which comprises 5.7 km of tunnels, 4.3 km of viaducts and 1.0 km of atgrade roads.The finally adopted alignment commences at the southern end with an interchange with the existingFanling Highway, part of Route 9, which is a dual three lane expressway currently being widened to dual4 lane. Alongside the expressway is the main rail connection to the mainland of China, and theinterchange viaducts connecting to the southern portal of the Lung Shan tunnel must cross over thisrailway. The southern portal is located in the foothills of Lung Shan, and the 4.8km long tunnel is alignedin a north-northeasterly direction. The southern half passes under mountainous terrain of Lung Shan,and then crosses a valley containing the Kwan Tei river. The northern section comprises low hillsseparated by an alluvial plain and Tan Chuk Hang village area. At the northern end, the tunnel turns tothe north-west to connect with Sha Tau Kok road, an existing single carriageway road, with a newroundabout interchange. Mid-way along this tunnel there will be a ventilation building, connected to the main tunnel by a 330m long ventilation adit. To the north-western side of this interchange is the900m long Cheung Shan tunnel, and after this the remaining 4.3km of the highway connecting with theBoundary Control Point is to be constructed as an elevated viaduct. The alignment is shown in Figure 1."

Jan 1, 2016

By P. S. Hettinger

Land Application Discharge (LAD) is a useful method of disposing of waste water from mining operations and in certain climatic regimes, stormwater runoff. LAD systems function under the premise that metals, salts and nutrients in water are dispersed over a large area and are effectively assimilated into the soil profile. Depending on the soil structure, migration or mobilization of dissolved metals through the soil profile can be Substantially reduced. Land application of treated effluent from sewage lagoons or waste water plants was probably the first general use of land applied water. LAD has gained popularity with the mining industry as a means of disposing of waste water and process water. In addition, large volumes of snow meltwater and stormwater are often placed in storage in Montana during spring, and Land Application Discharge has shown to be an effective method for disposing of stormwater during the dry, summer season. LAD can also provide an alternative to recycling or treating waste water at on-site waste water treatment plant&. Application of stormwater or process water can result in little or no change to the background concentrations of metals in baseline water quality samples. One cautionary note about LAD: high salt concentrations and pH values are associated with process water from heap-leach facilities and are known to cause burning of local vegetation. Some pre-treatment of process water may be necessary to prevent such environmental problems.

Jan 1, 1994