Search Documents

By Hemendra N. Kalia

To plan a safe and efficient coal mining operation, the design engineer should use all the available information regarding the property to be exploited. The reliability of the mining operation must be as high as possible so that the plants relying on the coal can operate at the maximum design capacity. A good design should incorporate all of the known geological characteristics of the deposit, the structural and physical properties of the coal, as well as the rock which will form the roof and floor of the mine openings. A systematic method is proposed as a guide to insure a mine design that will be safe, efficient and will minimize surface disturbances resulting from mining operations. It is anticipated that the method proposed will result in maximum extraction at perhaps minimum cost to the operator. In general, to develop a mining area, several factors are systematically reviewed: (1) determination of the economic minability of the deposit, (2) the computation of the coal reserves, (3) the marketability of the coal, and (4) the life of the property. In general, boreholes are drilled in a predetermined pattern and geophysical or geological methods are used to log the boreholes. The information so obtained is primarily used to determine the quality and the extent of the deposit and to determine to some extent such geological features as faults, barren areas, washouts, and channels.

Jan 1, 1973

By R. R. Fernández

Newmont Mining Corporation has been processing refractory gold ores by roasting since January 1995. The ores are refractory due to the association of the gold with iron sulfides, namely pyrite and marcasite, and the presence of carbonaceous components and is oxidized in an oxygen-enriched gaseous atmosphere. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent upon the roasting conditions, mainly the roasting temperature. Originally, the sulfides and carbonaceous matter were oxidized at a temperature that typically ranged between 535 and 560 °C. Controlling the roasting temperature within the lower and narrower range of 510 to 515 °C produced a calcine with a larger surface area(e.g. higher porosity), which resulted in a gold recovery increase of3.3 percent in 2001 equivalent to 5.1 million dollars of additional gross revenue. The new strategies of operating at temperatures never tested before are discussed. It constituted a great challenge to the control room operators for the lower operating temperature falls much closer to the ignition temperature of the sulfide ore and smaller and more frequent adjustments in operating parameters were needed to improve and maintain high gold recoveries. Based on the encouraging results that were achieved in 2001, a decision was made to install a “smart” process control system because the roaster temperature control was performed by manual inputs from the control room operators. The development and implementation of the control system to reduce or eliminate the temperature variability between the different control room operators commenced in June of 2002 and was fully operational by the end of October. Lower roaster temperatures were achieved (500 to 505 °C), which resulted in further increase of gold recovery by about two percent. The overall recovery increase equated to 8.0 million dollars of additional revenue for the first 10 months of 2002.

Jan 1, 2003

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

Adsorption experiments were conducted at two different solids loadings, to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In the region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region II, while surface precipitation was predominant in region III along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1986

The following errors were inadvertently included in "How millisecond delay periods may enhance or reduce blast vibration effects" by R.M. Wheeler in the September issue of Mining Engineering.

Jan 1, 1987

By John W. Wilson

INTRODUCTION In the past, the cost and time required for the construction of shafts has played an important part in the planning of underground mines. For reasons that are discussed later, the economics and technology of shaft construction in the future can be expected to play an even greater role in the planning of new mines and the operation of existing mines. Indeed, the very feasibility of a proposed mining venture may depend on the cost and timing of the shaft requirements. The most commonly used shaft sinking methods used today for excavating vertical shafts are discussed and the need for new technology and methods emphasized. In one study by the U. S. Bureau of Mines, it was reported that the coal industry in the United States alone could require 170 to 190 new shafts per year on the basis of doubling current production by the mid 1980's or 70 to 90 shafts on a more moderate coal production expansion program. This study concluded that the attainment of the required number of shafts would be unlikely with the present shaft sinking resources and costs. In order to meet the requirements for shafts in the United States coal and metal mining industries, more efficient and speedier shaft construction methods will be necessary. Current shaft sinking methods are, in the main, labor intensive, and it is noteworthy that it is becoming increasingly difficult to attract the work force required to sink shafts conventionally. Because of this situation, some attempts at mechanization have been made to compensate for this ever-increasing scarcity of trained

Jan 1, 1976

By Alan Fricker, Bill Owers

Cyprus Gold NZ Ltd will be recovering residual cyanide from their CIT, operation in New Zealand. The process will use air to strip the cyanide from the acidified barren pulp. DSffi. Industrial Development, who were involved in the bench and pilot studies for Cyprus, have extended the concept to pregnant pulp. The stripping of pregnant pulp eliminates the substantial loss of cyanide through carbon catalysed oxidation during the adsorption stage. A 50% increase in cyanide recovery was obtained from an extensive laboratory investigation. The presence of a cyanide recovery circuit enables leaching to be conducted, without detriment, at pHs at least as low as 9, with consequential 50% reductions in the consumption of lime and sulphuric acid. There should be a small reduction in carbon consumption, and a significant improvement in the quality of the final effiuent, at least in terms of cyanide, cyanates, copper, zinc and sulphur. A small but significant increase in gold recovery can be expected too. There is a net economic advantage of NZ$1.20/tonne of ore by stripping pregnant rather than barren pulp.

Jan 1, 1990

By M. S. Celik

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, boron minerals, colemanite, ulexite and borax undergo respectively decrepitation (fragmentation), shrinkage and expansion upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot plant studies on calcination of boron minerals conducted in our laboratories are reviewed along with their implications in commercial operations.

Jan 1, 1997

By Ronald H. Mullennex

The growing need for development of thinner, more erratic, or less easily- mined coals in the Appalachian region requires more detailed analysis of conditions and factors controlling or influencing deposition of these seams. The value of depositional modelling in evaluation of such coals has been demonstrated in many recent studies and publications. Such modelling may be applied to allow prediction of factors varying from regional coal occurrence trends to very local areas of seam discontinuities, but requires thorough utilization of all available types of data. Mapping of general depositional energies, as derived from basic geophysical and driller's logs, can be applied to specific prediction of coal occurrence, and projection of particular facies as representative of unique depositional features or conditions often proves more applicable to coal character delineation than does mapping of the coal itself. Depositional modelling and trend projection may also serve as a guideline in reserve classification and confidence-levels in reserve estimations.

Jan 1, 1981

By Jacques Bernazeaud

Rouez is a recent discovery of a major low-grade sulfide body (± 100 m, 0,6 % Cu, 0.3 % Pb, 1 ,5 % Zn, 21 g/t Ag, 1.5 g/t Au) in a populated farming area of Brittany, France, some 30 kilometres northwest of Le Mans. The discovery is the result of an airborne electro- magnetic (INPUT) survey. It is the first time that the INPUT method has been used in France. The survey Gas successful in spite of the numerous interferences normally found in populated areas. The lack of a good drainage system would not allow the discovery of Rouez using stream sediment geochemistry alone. Ground geophysical surveys confirmed the airborne work and gave sufficient information to make the first hole a discovery hole. The deposit is Proterozoic in age and sediment-hosted. The metamorphism is low grade.

Jan 1, 1983

By David W. Houston

The increasing energy crisis, coupled with stringent environ- mental regulations, has created new demands for high capacity materials handling systems with unit train transporting and continuing surveillance of quality control. Effective and efficient methods of material conveyance are through high speed, high volume conveyor belts with the monitoring of quality through the utilization of automatic sampling. When we speak of high speed, high volume belt discharges we are referring to speed ranges from 600 to 750 FPM and volumes as high as 5500 TPH. To achieve the optimum operating sampling system for high capacity belt discharges, it is imperative that two major design characteristics be investigated and evaluated; namely technical analysis of operating conditions through application of ASTM design criteria and practical experience in the selection of equipment and the design of related components. The task of obtaining a sample of reasonable weight to represent an entire lot presents a number of problems and emphasizes the necessity for using standard sampling procedures.

Jan 1, 1973

By Edmond F. Lawrence

The Calico area lies within the Walker Lane fault zone, six miles north of Schurz, Nevada. The mineralized area is overlain by a thick section of Tertiary tuffs and ash-flows, that have been intruded by a series of andesite plug, dikes, and sills. The pre-Tertiary rocks outcrops only in two areas at one to two miles distance from the drilling areas. Underlying the volcanics are sediments ranging from siltstones, sandstone, calcareous shales, to carbonates of the Luning sequence. These have been intruded by one or more phaneritic intrusives ranging in composition from quartz diorite to quartz monzonite, with the development of a skarn zone on the south flank that contains extensive mineralization consisting of magnetite, pyrrhotite, pyrite, and chalcopytite, with traces of sphalerite, galena, and molybdenite. The magnetite, pyrrhotite, and part of the pyrite appears to be contemporaneous with the skarn, while, part of the chalcopyrite, galena, sphalerite, molybdenite, quartz, and calcite, occurs as minute veinlets cutting the other minerals. This later mineralization may be associated with a late stage of the same sequence, or possibly associated with another intrusive to the southwest. Geophysical work has consisted of aerial magnetics, ground magnetics, gravity, seismic, and induced polarization surveys. Preliminary induced polarization surveys indicated anomalies at depth, both over the magnetic anomaly and to the northwest. Subsequent IP work confirmed this earlier anomaly, and drilling disclosed extensive mineralization at depths of 400 feet on the northwest end and over 1,000 feet to the southeast.

Jan 1, 1967

By R. L. Braun

In situ chemical mining of primary sulfide ore requires distribution of injected oxygen in a large underground flooded region of broken ore. Although the maximum oxygen content of the leach solution will be dictated by the operating temperature and hydrostatic pressure, the actual oxygen content will be limited by the geometric dispersion of the injected oxygen, the rate of dissolution of oxygen, and the rate of convective circulation of oxygenated solution within the flooded bed of ore fragments. These factors are examined by a detailed theoretical analysis supported by laboratory experimental data. Typical results of the study illustrate that adequate dissolution of oxygen and circulation of oxygenated solution can be obtained in a column of 4 million metric tons of broken ore by using three gas injection lines and an oxygen injection to consumption ratio of 1.84.

Jan 1, 1974

By Haydn H. Murray

Since the advent of machine coated paper in the mid 1930's, the kaolin industry has had a remarkable growth, In 1935 the domestic production of kaolin was 500, 000 tons and in 1970 the estimated production was in excess of 3. 5 million tons. The process industries which use kaolin most extensively are paper, rubber, paint, ceramics, plastics, catalyst manufacturers, ink, and pharmaceutical. The paper industry is by far the largest consumer of kaolin using approximately 70 per cent of the total tonnage mined and beneficiated. Up until 1970 the major kaolin producers were able to expand rapidly enough to supply the demand but for the first time in thirty years the demand is expected to be in excess of mining and beneficiation capacity through at least 1975. The major reason for this is the expansion of coated paper production in Europe and Japan. Two areas supply the lion's share of kaolin for the world markets. These are the Cornwall area in extreme southwestern England and a limited area of Georgia and South Carolina in the southeastern U. S. The English kaolins are primary - (found in decomposed granite) whereas the Georgia-South Carolina kaolins are secondary - (found in lenticular, continuous beds in the Tuscaloosa formation of Cretaceous age. ) The English kaolins are mined by hydraulic methods whereas the Georgia-South Carolina kaolins are mined by dragline or shovel and benefidated by using a wet process for the majority of the production and/or a dry

Jan 1, 1971

By John B. Wright

This paper describes laboratory techniques and subsequent results of Bureau of Mines research to produce chlorination-grade feedstock from an abundant, low-grade, domestic, rock ilmenite ore. The research is part of the Bureau-effort to devise technology that may help decrease U.S. dependence on imported raw materials. A rock ilmenite containing about 46 wt pct Ti02 was smelted in an electric arc furnace with coke, woodchips, and Na2C03 to separate most of the iron as pig iron and to form a low-iron, titanium-enriched slag. The slag was ground, pelletized, oxidized, and then sulfated with mixtures of SO2 and air in a continuous 4.5- to 9.1- kg/h apparatus at 1023 to 1223 K. The sulfated slag, containing 60 to 65 pct TiO2, was reground and leached in water at ambient temperature to decrease the combined levels of the troublesome Ca, Mg, and Mn impurities from 7.0 to 1.7 wt pct. At levels of more than 3 wt pct, these impurities contribute to operating and disposal problems, The final product was upgraded to about 84 wt pct TiO2. This material potentially is suitable for chlorination in a fluidized-bed reactor. The most favorable results were achieved with leached slag sulfated at a feedrate of 4.5 kg/h and at temperatures of 1073 to 1123 K.

Jan 1, 1984

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes' Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975

By Gösta W. Diehl

During the past five years the use of all-hydraulic drilling equipment has increased rapidly, and we have now reached a point where the hydraulic drill has become an alternative to be seriously considered for every drilling operation. The hydraulic drills have many advantages over pneumatic drills, but they also have certain characteristics, which makes a potential user hesitate before making the switch. And when the decision to use hydraulic drills has been made, the user then faces another choice of equal difficulty: the choice between different hydraulic systems. This paper discusses some of the factors to be taken into account when considering hydraulic drilling equipment for rapid tunneling in hard to medium hard rock. THE CHOICE BETWEEN HYDRAULIC AND PNEUMATIC EQUIPMENT The choice between a hydraulic and a pneumatic drill is much more than just that: It is a choice between two different systems. The choice is usually based on the productivity, economy or ergonomy of the system. However, also other factors should be considered, such as service capabilities and training requirements. And finally the choice will be influenced by the need to acquire know-how in the new technology. Productivity If the prime consideration is to achieve the highest possible tunneling speed, then the high penetration rates of the hydraulic

Jan 1, 1979