Search Documents

By S. C. Lamey, P. A. Hesbach

This study evaluated the use of regionally produced coal combustion products to neutralize and remove metals from acid mine drainage (AMD). Synthetic AMD mixtures were treated with a number of fly ashes and fluidized bed combustion (FBC) ashes. All of the ashes reduced the volume of the sludge produced and gave a faster settling rate than the sludge produced by treatment with lime. Faster settling allows greater throughput rates. In addition, the FBC ashes, which generally contain alkaline components used for sulfur capture, completely neutralized the acidity and, if desired, raised the pH above 10. The fly ashes, on the other hand, reduced the final volume of sludge but required additional neutralizing agents to attain a pH >5. The pH of the AMD can be taken to above 10 to insure complete removal of manganese, or it can be taken to a more neutral pH of 7 or 8 to allow for the safe introduction of the aqueous phase into ponds or streams. The process combines two industrial waste products to reduce the disposal volume of one of the waste products and to produce an environmentally safe aqueous discharge.

Jan 1, 2002

By Alfred W. Eustes III

The first of a series on the evaluation of rock cutting tools, this paper discusses the results of full-scale laboratory drilling tests that compare the performances of several polycrystalline diamond cutter (PDC) coring bits. The tests were performed in welded tuff as part of a site characterization program. Number of cutters, size of cutters, air course design, and other parameters were evaluated as they affect penetration rate, but this paper focuses mainly on the relationships of torque vs. thrust (weight-on-bit), specific energy vs. penetration rate, and thrust vs. penetration rate. These relationships change in diagnostic ways according to bit type, bit condition, and type of welded tuff.

Jan 1, 1998

By C. P. Boddy

One of the most difficult tasks a project manager will have in pre-mine planning is dealing with the mine site's hydrologic regime. Numerous federal statutes passed by Congress in the last decade have made the coal mining industry more responsive to the environmental impact during all phases of the mining process. Permitting these mines has dictated a cradle to grave approach in dealing with water related issues. This paper will attempt to explore the application of these technology- based laws and their direct application to the unique environment found in Alaska's interior regions.

Jan 1, 1985

By C. J. Im

As market conditions become more competitive, U.S. coal producers are faced with the increasing need to find methods of lowering production costs in their operations. One area worthy of investigation is the additional recovery of fine coal that is normally discarded in the preparation plant waste stream. United Coal Company is currently assessing the capability of the Deister Flotaire, a new application of a column flotation cell, to recover additional, saleable coal from preparation plant waste. This paper presents the technical data obtained to date. Work with a 0.76 m (30 inch) diameter cell installed in a plant shows considerable coal recovery is possible from a nominal 0.595 run (28 mesh) X 0 refuse stream.

Jan 1, 1986

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By P. Lan

Gold is often associated with arsenopyrite in many refractory gold ores. The selective recovery of arsenopyrite by flotation is therefore necessary in order to maximize the recovery of gold. However, the complexity of arsenopyrite flotation often makes it difficult to obtain a high recovery from real lean gold ore. This paper presents the results of arsenopyrite flotation by ultrasonic pretreatment in micro flotation experiments and bench scale flotation tests. The tests showed that pure arsenopyrite exhibited low natural floatability due to the oxidation on the mineral surface under ambient conditions. Using ultrasonic pretreatment, the oxidation film was ruptured and the floatability was enhanced greatly. The presence of Fe (III) was found to inhibit the flotation of arsenopyrite and this depression was also removed by the ultrasonic pretreatment. This result explained why the arsenopyrite in real ore is often difficult to float and how ultrasonic pretreatment can effectively improve the arsenopyrite flotation in real gold ores. Guanidine (GMM) was found to be a superior collector for arsenopyrite in acidic medium and xanthate in alkaline medium.

Jan 1, 1998

The paper describes a practical methodology based on numerical modelling for the prediction of progressive failure of underground mine stopes with cable bolt support. A case study of the 40-761 stope at Kidd Creek Mine, Timmins, Ontario is presented. The stope was mined by blasthole open stoping in 1986 as a lead stope within a mining block between 36-1 and 38-2 levels. Initially designed to peak at 38-2 level, the stope back caved upwards approximately 40m towards 36-1 level. Cable bolts were installed above the stope from 36-1 level after caving had begun. The stope eventually stopped to cave when the falling rock mass encountered a sufficiently high cable density. The paper provides details of the geomechanical data and modelling results of the case study. Numerical modelling is carried out using a finite element package known as e-z tools which has, among other things, a special cable/rockbolt simulation capability.

Jan 1, 1994

By H. Sis

The pressure filtration behavior of dispersed and flocculated alumina slurries at high percent loadings is discussed with an objective to determine the effect of surfactant type and concentration on slurry properties. A high purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by surfactants that are considered to act by electric and steric stabilizers. The effect of both the ionic and nonionic surfactants was investigated. Surface charge measurements of the slurries were carried out by electrokinetic sonic amplitude (ESA) method to understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and final cake properties are discussed.

Jan 1, 1998

By E. A. Rychkun

Mining and environmental objectives have traditionally been in conflict. This conflict reflects a delicate balance between the need to spend money to protect the environment, and the need to save money by extracting minerals efficiently. In an increasing number of cases, profit margins diminish rapidly with new environmental regulations and reactionary measures. Forced cleanups and increasing restrictions are unwelcome expensive processes. A practical solution lies in planning rather than reacting. This requires the ability to precisely quantify and qualify environmentally sensitive problems by providing effective engineering tools to model, visualize and analyze subsurface conditions. Prevention of environmental conflicts, and effective cost control are both rooted in the mining company's ability to construct accurate models, monitor changes, assess contamination risks and to design effective remediation plan. This paper presents a case study where these issues are addresses through the application of a new and innovative technology.

Jan 1, 1993

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By Daniel G. Ganey

Kerr-McGee Coal Corporation has used diesel face haulage and support equipment at its dual-seam Galatia Mine in Southern Illinois since production activities commenced in 1983. The mine began production from its lower seam, the Harrisburg No. 5 coal seam, in October 1983 and from the upper Herrin No.6 coal seam in April 1985. Before production began, the company developed a program designed to make use of the flexibility offered by diesel equipment. While productivity was an important goal, the top priority of the program was to provide a safe and healthy work environment for the miners. Management believed that high productivity would naturally follow. History has proven this belief to be true.

Jan 1, 1990

By Richard H. Olson

Talc is currently mined in the U.S. in six major districts. The size and depth of the ore bodies and their mineralogy dictate the types of products manufactured and the mining and processing methods which must be employed. The geology of the major deposits is well known and will be but briefly discussed The major emphasis will be placed upon the past history of the districts, the size and depth and configurations of the ore bodies, the ore mineralogy, and how all of these factors govern the types of mining and processing operations which may be employed in each of the districts.

Jan 1, 1984

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

By Ted H. Eyde

Nearly 17 years ago a major producer of synthetic zeolites started an extensive exploration program for natural zeolite deposits which resulted in the discovery of over 170 occurrences in the western United States. A few years later several of the other producers and consumers of synthetic zeolites also started similar exploration programs. Since then, small quantities of natural zeolite minerals have been produced from at least 12 deposits in the United States. Of these the Bowie deposit, about 13 miles north of Bowie, Arizona, is the most important,having produced over 5,000 tons of vitric tuff zeolitically altered to the mineral chabazite and minor amounts of the minerals erionite and clinoptilolite. Mining Districts and Mineral Deposits of Arizona compiled by Charles A. Mardirosian, Consulting Geologist, estimates the value of the total production from the Bowie deposit at a very conservative $2,000,000. Unfortunately, none of the companies responsible for the discovery and the initial production of natural zeolites made any effort to develop the high volume, low cost applications of this unique mineral raw material. Instead, they developed only the high unit value uses to supplement their existing synthetic molecular sieve product lines. With the producers of synthetic zeolites thinking in pounds and not in tons, further development of natural zeolite deposits stagnated for over a decade.

Jan 1, 1974

By Robert R. French

Commercial grade gypsum beds up to 16 feet thick is present in southwestern Indiana. The major deposits are found at a depth of 350 feet to more than 500 feet below the surface. The ore body averages about 75 to 95 percent gypsum. Two companies are currently exploiting a deposit which underlies an area of several square miles near Shoals, in Martin County. Another deposit has been located in southwestern Owen County but has not been developed. The Indiana Geological Survey is currently drilling in Greene County and is considering further exploratory work in Perry end Dubois Counties.

Jan 1, 1965

By F. A. Campbell

This paper reports on mineral facies, ore textures, distribution of iron in sphalerites, and fractionation of sulfur isotopes in the Anvil ore body, Yukon Territory, Canada. Because the detailed structure and stratigraphy, both regional and local, are being studied by the geological staff at the mine and members of the Geological Survey of Canada, these topics will be discussed only briefly. The results of our study of the Anvil ore body have implications on theories of the genesis of ore deposits of this type, and these will be discussed. The Anvil ore body is the largest and most significant of three lead-zinc discoveries in an area of the central Yukon where major lead-zinc deposits were unknown only twenty years ago. The Vangorda deposit consisting of 22 million tons was discovered in 1953, followed in 1954 by the Swim Lakes deposit consisting of 10 million tons. The Anvil deposit, which consists of three ore zones, was discovered in 1964. The total reserve at Anvil mine is 63.5 million tons, with an average grade of 3.4% lead, 5.7% zinc, 0.16% copper and 1.2 ounces of silver per ton. This study is concerned primarily with the number one ore body which is about 2,400 feet long, up to 1,100 feet wide and 300 feet thick.

Jan 1, 1973

By Robert B. Hopler

For many years the explosives industry was a technological enigma: it was at the 'cutting edge' of some technologies and in the backwaters of others. For example, for at least the past 85 years, the industry routinely measured time to one-millionth of a second for determining the detonation rate of explosives. At the same time, however, formulations were usually hand-written in 'formula books,' such as the alchemists may have done. Also, due to the fact that the equipment had proven to be safe, many of the mixers and packing machines in use until recently were those patented in the 19th century; improving efficiency was not worth the possible risks that might be encountered. In recent years, the wide availability and portability of computers and their adaptation to specialized applications have revolutionized the explosives industry, much as it has many others. With the advent of the water-based emulsions and slurries (water gels), and the necessity to design totally new processing and delivery equipment, the opportunity arose to apply modern techniques to many aspects of the business. Table 1 lists some computer applications currently in use by explosives manufacturers and end users. The use of high-tech production controls, equipment design aids, field measurement devices and other computer applications is so pervasive in the industry today that any brief article such as this must be considered only as a broadbrush overview of the subject.

Jan 1, 1994

By Rees D. Groves

Cement copper is ordinarily converted to marketable metal by processing in a conventional smelter and refinery. Because of rapidly increasing cement copper production and limited excess smelting capacity, other techniques were investigated for preparing marketable copper products. One route was to make copper powder for industrial use. The process scheme employed flotation for rejecting the bulk of the impurities, acid leaching to remove residual iron and aluminum, reduction sintering to eliminate oxygen, and grinding to obtain powder. Another route was to sinter the floated and leached copper into the form of anodes and electrolyze these to yield refined copper cathodes. At a current density of 30 amperes per square foot, power consumption for electrorefining was 185 kwhr per ton of copper. The feasibility of preparing commercial-size anodes by sintering is still to be assessed.

Jan 1, 1970