Search Documents

By B. G. Stone

"INTRODUCTION “Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole” (Baxter and Parks, 1939) “An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence. The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling. Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive.” (McKinstry, et al., 1948). In an actual orebody, the accuracy of sampling depends not alone on the number of samples but also on proper distribution of them throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore it is important to select the places in such a way that all parts of the orebody will be represented. “For those who cultivate land which is alike arid, heavy , and barren, and in which they sow seeds, do not make so great a harvest as those who cultivate a fertile and mellow soil and sow their grain in that. And since by far the greater number of miners are unskilled rather than skilled in the art, it follows that mining is a profitable occupation to very few men, and a source of loss to many more.” (Georgius Agricola page 5 Book 1 as translated by H.C. Hoover and Lou Henry Hoover, 1950)“It is evident that mining is very profitable to those who give it care and attention”"

Jan 1, 2015

Coal has traditionally been an integral part of life in Kentucky. Coal mining produces a large part of revenue for the Commonwealth of Kentucky and provides a significant number of jobs to the residents of eastern (less in western) Kentucky. Recently, however, the coal industry of Kentucky has had to endure many hardships. The Clean Air Act set forth sulfur dioxide emission standards which have severely affected much of the coal mining industry in Kentucky, because much of the coal mined in Kentucky has a high sulfur content. In this paper, the background around the effects of Clean Air Act on the coal industry is introduced. The economic and social effects of the Clean Air Act on the Kentucky coal mining are addressed.

Jan 1, 1993

By H. H. Murray

Abstract. World reserves of bauxite are abundant. Domestic reserves are limited and as a consequence the United States must rely on foreign suppliers for over 90 percent of its bauxite. Nationalization of many bauxite mining operations, levying of higher taxes, increased production and transportation costs, and attempts to create a uniform market price combined to place the United States in a vulnerable position. Alumina from kaolin, alunite, anorthosite, and oil shale have-been-or are being evaluated. World bauxite reserves are increasing and attempts to establish a uniform price have failed; therefore, it may be many years before domestic non-bauxite sources of alumina can compete with imported foreign bauxite.

Jan 1, 1980

By Raymond L. Jones

With the inauguration of the open pit operation in Bagdad, plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until the spring of 1961. Like all neophytes, we started something about which, on a commercial scale, we knew next to nothing, either dump preparation or leach procedure, and as a consequence, we are still paying the piper. True, we had been through an extensive laboratory pilot program, but it soon became apparent that there was considerably more to increasing solution volumes than simple multiplication. Had we initially possessed our present acumen, the Cyprus Bagdad plant could be operated more efficiently and at a better profit. During the past several years, the art of dump leaching of copper has improved in many ways, primarily because of the application of scientific principles gleaned from general mining practice. Rigid pH control and the use of atomic absorption techniques for rapid," accurate assaying have probably played a leading role in this respect, although we cannot overlook the other sophisticated electronic controls lending improvement to acid addition and pumping, better piping materials, and lastly, the more efficient use of our pregnant liquors. Thin too, the years of experience have given us a greater understanding of dump behavior in general; and, we can, to a greater extent, measure, predict, and avoid some of the idiosyncrasies inherent in every dump. However, it is my firm belief that we will still be confronted with unexplainable dump behavior as long as we are involved in leaching. We have found our dump to be a wonderful money bank, but one that is capable of yielding a wildly fluctuating profit.

Jan 1, 1975

By Laurence E. Snow

The conversion to the use of commercial grade ammonium nitrate (CGAN) for use in blasting at the Utah Copper Pit of the Kennecott Copper Corporation has presented unique problems for the Drilling and Blasting Department, In order to better understand these problems, a' picture of the Bingham Pit might be helpful. Some quarter of a million tons of ore and waste must be blasted daily in order to keep thirty-eight electric shovels operating. All material is blasted by "toe holes" of 24 to 28 feet in depth, drilled from prepared drill grades and sloped so as to bottom approximately 5 feet below the bench level. Horizontal spacing of these holes averages 22 feet, with exceptions being made where faults occur in the bank. These "toe holes" are drilled by 4-inch drifter machines, mounted on self-contained mobile drill units using .3-inch starter bits and bottoming at a minimum of 2 1/2 inches in diameter, "Toe-hole" drilling amounts to about two-thirds of the total drilling. In the higher bank sections of the Mine and wherever necessary, single rows of "down holes" are drilled to 28 feet in depth and spaced, on the average 23 feet apart. These holes are also drilled by a mobile drill. "Down hole" drilling amounts to about one-third of the total drilling.

Jan 1, 1959

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Miguel Sanchez, Carmen Scalise

"Chicago’s Tunnel and Reservoir Plan (TARP) is a nearly $4.0 billion and over 30 years long program and arguably the largest and longest combined sewer tunnel and reservoir system in the world. Recently, a massive tunnel construction is underway for connection of the McCook Reservoir to the existing TARP tunnel system. Once completed in two stages in 2017 and 2019, the reservoir will hold 38 billion-liters (10 billion-gallons) of combined sewer overflows (CSO) and flood waters from the city of Chicago and over 20 communities in Cook County, Illinois. McCook Main Tunnel will connect Chicago TARP’s Mainstream Tunnel to the McCook Reservoir. Connecting two 10-meter (33-ft) diameter tunnels at 92 meters (300 feet) underground has not been a simple task for the McCook Tunnel Project participants, the project owner U.S. Army Corps of Engineers (USACE), local sponsor Metropolitan Water Reclamation District (MWRD) of Greater Chicago, designer Black & Veatch, and the contractor, Kiewit Infrastructure Company (Kiewit). Yet alone excavating and lining massive size tunnels, the team is also challenged with live tunnel conditions in TARP Mainstream Tunnel that carries CSO and flood flows from city of Chicago which runs full during rain events and must remain in service at all times. The project is a noteworthy feat for engineering and construction with the upcoming installation of world’s largest underground wheel gates for flow control within the tunnel. In this paper, we describe one of its kind elements of this major tunnel system along with key design and construction considerations, specifically for the live tunnel connection which is a rare occurrence in the tunneling industry. INTRODUCTION The McCook Main Tunnel system consists of a 10 m (33 ft) finished diameter and 490 m (1,600 ft) long hard rock tunnel constructed from a 27.5 m (90 ft) diameter and 92 m (300 ft) deep main gate and tunnel construction access shaft. The gate shaft houses six high head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steel lined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir."

Jan 1, 2016

By W. A. Lawruk, L. J. Wilson, D. E. Stief

The Tower mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine and its operation, application, and performance for wet grinding.

Jan 1, 1988

By Ernest N. Wolff

You here are all familar with the myriad of new laws, some enacted and some pending, that affect the mining industry. These laws, for example those dealing with suspended matter, affect us in Alaska as they do you. Likewise, our friends in government, the Geological Survey and the Bureau of Mines, provide us with the same fine services that they do elsewhere. I am not going to speak today about these, but concentrate on one act of Washington, D.C. the impact of which is felt, for now at least, principally in Alaska. A little more than a year ago, I spoke in Spokane on the subject, "Governmental Challenge to Mineral Development in Alaska." I outlined some of the policies of Government which were operating to change the rules under which the industry operates and to alter the relation- ship between government, industry, and the individual. At that time the Native Claims Settlement Act had not been passed, but was on the verge of being so. In reading over what I said in Spokane, I note that I touched on many points where Government was actually challenging mineral development in Alaska. With the passage of the Alaska Native Claims Settlement Act, many of these actions were given a cloak of legality, and machinery was set up to concentrate the drive to tie up the public domain, machinery which will allow govern- mental control and interference with the actions of individuals on something like 90% of Alaska's land surface. This remarkable law is going to affect each and every one of you. Now, a year after its passage, we are only just beginning to see its lesson for the future. It was created by a coalition of powerful groups, who got other groups to support them by promising to deliver something they had no intention of delivering. Alaskan issues are again being used to get various groups not to oppose legislation which will severely harm them. It will help to understand the nature of this new drive if we understand the Native Claims Act and how it came into being.

Jan 1, 1973

By Todd Kilduff, Paul Wilkinson

Microtunneling is rarely a straight forward “business as usual” endeavor. More often than not, these projects take twists and turns that require on the fly, out of the box solutions to get the project completed. This paper is a case history of a 63-inch diameter, Permalok, microtunneling project, extending nearly 700 linear feet under a hill forming the left-hand abutment to an earth embankment tailings dam. The job had three major and unexpected challenges that required unorthodox solutions. Challenge #1— Face Configuration: The Santiago Formation, a cemented sand formation with widely varying strengths, presented a challenge to configuring the face with regards to the number and length of pics and cutters. Subtle differences in type and size of the tooling had a big impact on the performance of the machine. Challenge #2—Eccentric Loading: Issues at the launch shaft with the Permalok pipe adaptors caused eccentric loading on the casing pipe. This issue resulted in overstressing and breaking of several pipe joints that ultimately led to seizure of the tunnel. Challenge #3—Back-tunnel Excavation and MTBM Recovery: There were many detailed considerations into excavating a recovery tunnel to retrieve the MTBM, especially being under a high hazard earth embankment dam.

Jun 13, 2021

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1997

By A. S. Ibrado, D. W. Fuerstenau

"Gold, silver and copper form various complexes with cyanide, of which only the singly charged dicyano form adsorbs appreciably on activated carbon. The adsorption of the dicyano complexes appears to be controlled predominantly by chemical reaction at the surface of a shrinking unreacted core. Metal uptake over time is non-linear, which eliminates control by boundary layer diffusion. The rate of adsorption is not enhanced by a reaction interruption, which suggests the absence of concentration gradients in the pores. Finally, the rate of adsorption increases with decreasing activated carbon size in a manner consistent with the shrinking core model. The results of this investigation accentuate the importance of efficient acid washing of carbon and removing carbon fines from the barren carbon stream. INTRODUCTION With the dwindling reserves of high-grade ores, most of the world’s gold is produced from low-grade ores by cyanide leaching. In the past, leaching was followed by the Merrill-Crowe process, in which gold is precipitated from clarified pregnant solutions by zinc cementation. This process is still being used for high-silver ores, where the cost of carbon stripping becomes prohibitive. For deposits with silver-to-gold ratios of about 4 or less, adsorption on activated carbon would be the usual solution purification step taken. The process simplifies solid-liquid separation and offers a viable solution to preg-robbing organic carbon in some ores. The modern industrial application of carbon adsorption started with the carbon-in-pulp (CIP) process, where carbon adsorption was used mainly as a solution purification step. In 1973, Homestake Mining Company commissioned the first large-scale CIP plant in the U.S.A.1 Later, carbon was added earlier in the circuit to control preg-robbing by adsorbing gold cyanide onto activated carbon as soon as it is dissolved. The scheme is successful because activated carbon is a stronger adsorber than the organic carbon found in preg-robbing ores. This process came to be known as the carbon-in-leach (CIL) process. Numerous research investigations have been performed on the chemistry involved in the CIP process, which at the time of its introduction was not clearly understood. Of these, research on the kinetics of adsorption probably bears the most immediate impact on industrial practice,2,3 where adsorption systems rarely reach equilibrium, if at all, and slight slowdowns in the adsorption rate can translate into significant decreases in revenue. To illustrate this, organic compounds, like flotation reagents, have been known to impair CIP circuits. However, laboratory tests showed that the organic compounds do not significantly affect the adsorption capacity of activated carbon. Rather, the harmful effect may be attributed to a lowered adsorption rate.4,5 Also well known is the faster rate at which fine activated carbon powders reach equilibrium compared to coarse activated carbon, even though the final (equilibrium) amount of material adsorbed per unit weight is the same."

Jan 1, 2015

By Chris D. Breeds

Northwest Boring, Inc. (NWB) deployed a skinned up AVN 2000AB Microtunnel Boring Machine (MTBM) to install 7.5-foot long, 118-inch outer diameter reinforced concrete pipe (RCP) sections along an alignment between the Fremont (FRS) jacking shaft and the 3rd Avenue (3RS) receiving shaft for the Ship Canal Water Quality SCWQ Project. The alignment includes: a 67-foot long straight section, a 367-foot long curved section excavated along a 650-foot radius curve, followed by a 182-foot long straight section. This paper describes the project including planning and design, manufacturing, equipment installation in the 90-foot-deep FRS jacking shaft, egress through the secants and microtunnel operations required to complete the shaft and install the required casing pipes.

Dec 1, 2022

By J. R. Schafler, J. L. Brinkman

"The US coal mining industry has suffered a recent decline in profits caused by a combination of decline in commodity demand and more restrictive government regulation, forcing coal mining companies to cease production in numerous mines. A 40% decrease in the total number of coal mines occurred from 1994 to 2000. The number of mines remained relatively constant until 2008 when a change of government sparked a series of new environmental regulations which have contributed to another 15% decrease from 2008 to 2016. In contrast, production has only decreased by 3%, increasing from 1994 to 2008, and then decreasing since 2008. However, this value is skewed by large increases in sub-bituminous coal production and decreases in other coal ranks. Several aspects assist in executive decisions on mine longevity and economic worth. Studies of open source mine data collected by mandated government surveys coupled with commodity history can be used to find relationships between mine closures and these elements, which include statistics on production tonnage, seam height, coal rank, etc. This paper looks at coal mining trends since 1994 by comparing mine, market, and regulation factors that may influence mine closure. INTRODUCTION The US coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history, and regulatory impact. TRENDS SINCE 1994 Each year, US coal mines are required to submit data on a wide variety of categories to the Mine Safety and Health Administration (MSHA) and the US Energy Information Administration (EIA). This data includes administrative records, production values, and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the following figures."

Jan 1, 2017

By Vishnu S. Gupta

A modular computer program APEX (AMAX Process Evaluation Executive), has been developed at AMAX Extractive R&D, Golden, Colorado to facilitate rapid simulation of steady state material and energy balances of existing and/or proposed metallurgical process flowsheets. Currently, APEX is being used for the design, analysis, and evaluation of several of AMAX?s Nickel, Molybdenumand Tungsten processes. A unique feature of APEX is that it allows specifications of flow rates and compositions for different solid size fractions in addition to aqueous organic and gaseous phases. Thus, a metallurgical process which may involve crushing, grinding, flotation, leaching, washing, solvent extraction, precitation and refining operations can be simulated in a single computer run using APEX. APEX requires two input data files. The first is a process data file which includes physical and thermodynamic properties of the various chemical components of interest. This data file is unique to the process under study and does not require changes for alterations in the process flowsheet. The second data file is specific to a simulation case and includes descriptions of the flowsheet, various feed streams and the process equipment's operating conditions. In addition to temperature, pressure and percent solids, calculated information for each stream includes weight and volumetric flow rates, chemical compositions, specific gravities and enthalpies of solid, liquid and gas phases. For each process equipment in the flowsheet, APEX prints its operating conditions and detailed information about the streams that enter and leave the unit. Models of several general unit operations are preprogrammed in APEX. Also, the modular design of APEX permits quick and easy additions of simulation models which are specific to new and/or unique process operations. To study process stability and optimization, APEX permits several cases of a flow-sheet to be run together. Three simulations of the Moa Bay Nickel process have been excluded to illustrate the ease and flexibility of using the APEX system.

Jan 1, 1980

By William E. Mead

The process of selecting a building site for a major structure is a complex procedure involving the consideration of a multitude of factors. The approximate geographic location for a structure is usually fixed by its intended function, though often there may be several site alternatives. Socio-economic, logistic, marketing and political factors are the primary site determinants. Also critical in site planning, however, are the environmental factors, both natural and man-made. These factors will influence the precise siting location within the limits allowed by the primary determinants and will dictate some of the basic design criteria. This paper discusses environmental factors, principally those which are natural conditions, that must be analyzed for five different groups of structures. The importance of thorough site environmental analysis based upon the principles of applied earth science is described. Significant elements to be considered in an appraisal of the geology, hydrology, seismology and meteorology are outlined.

Jan 1, 1968

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing Computational Fluid Dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models utilizing Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.INTRODUCTION Methane gas and respirable dust are two hazards frequently encountered at continuous miner (CM) operations. An accumulation of both methane gas and coal dust may lead to massive explosions underground [1], and overexposure to respirable coal dust can result in pneumoconiosis (commonly referred to as “Black Lung Disease”) in coal workers [2]. Current U.S. federal coal mine regulations limit concentrations of methane gas to below 1% at the face area and require exposures to respirable coal dust to be at or less than 2.0 mg/m3 for an 8 h shift average. Begin on August 1, 2016; the overall respirable dust standard in coal mines is reduced from 2.0 to 1.5 mg/m3 for full shift sampling. If the quartz content of the dust exceeds 5% by weight, the dust standard becomes more stringent, reducing the allowable concentration to the value of 10 divided by the % quartz."

Jan 1, 2015

By B. D. Hong

The Coal supply and demand review arrived too late to appear in the May issue. In 1991, the US coal industry produced 902 Mt (994 million st) of coal, according to preliminary data compiled by the Energy Information Administration (EIA) (Table 1). This amount was 32 Mt (35 million st) less than the record 933.5 Mt (1 billion st) produced in 1990. Most of the decrease in coal production occurred east of the Mississippi River. The substantial stock buildup that stimulated production in 1990 was not repeated in 1991. In addition, coal consumption by electric utilities and coke plants dropped by about 1.8 Mt and 4.5 Mt (2 million and 5 million st), respectively. Moreover, a higher level of coal exports failed to bolster the 1991 production. Production Surface mines accounted for about 59% of the 902 Mt (994 million st) of coal produced in 1991. Underground mines produced for 41%. More than one-fourth of the total coal output was from federal and Indian coal leases. Production of all ranks of coal, except subbituminous, declined in 1991. Bituminous coal is produced mainly in the East. It totaled an estimated 590 Mt (651 million st), a 6% decrease. Production of subbituminous coal, mostly in the West, rose 3% to a record 228 Mt (252 million st). Lignite output was from Texas and North Dakota. It decreased by 1 % to 79 Mt (87 million st). Anthracite production, all from eastern Pennsylvania, fell by 17% to 2.7 Mt (3 million st).

Jan 1, 1992