Search Documents

By Michael Murphy, Gamal Rashed, Brent Slaker

Many underground stone mines in the United States operate on multiple mining levels. The effects of interburden thickness, pillar offset between mining levels at various depths of cover, and in situ stress conditions are poorly understood. Pillar offset is the degree to which pillars are not columnized or stacked. In this study, calibrated numerical models are used to examine limestone pillar stability in these conditions. Also, the critical interburden thickness required to minimize the interaction between mining levels is explored. The model results show that there is interaction between numerous factors that control the stability of stone pillars in multiple-level conditions. The highest degree of local pillar instability occurs when pillar overlap ranges between 10 and 70 percent. The highest degree of stability occurs when pillars are stacked.

Jan 1, 2023

By Thomas Konstantis, Spyridon Konstantis, Panagiotis Spyridis

"Tunneling and Underground works are unequivocally subject to a diversity of inherent uncertainties associated with the geotechnical, hydro-geological and environmental regime that surrounds them. On many occasions, these uncertainties can provoke loss events of considerable consequences. The present contribution elaborates on losses that the insurance market has suffered in the recent years, following a construction failure event. These losses are being considered and analysed on a quantitative basis through evaluation of cost related data, with explicit discretization of the applied construction methodology and of the subsequent developed failure type since both of which are considered of major importance. Given the identified persistence and regularity of some loss-contributing factors, recommendations are provided on the basis of a proactive risk engineering management approach that are envisaged to reinforce the understanding of project risks and alleviate the incurred insurance cost. 1 INTRODUCTION The underground construction sector has always been a very challenging area for all involved parties, including the insurance market. Main reason for that remains the uniqueness of the uncertainties sources and the subsequent inherent risks that the tunneling and underground projects are exposed to. In many instances, these risks materialize, leading to loss events with substantially high impact on reinstatement cost and incurred delays, which depending among others on the insurance coverage will have to be bared by the Insurance market. In the recent decades and as the tunneling industry boomed and expanded with many major and significant projects undertaken around the world, the insurance market was faced with additional challenges. Increased competition during tender coupled with the scale and complexity of the projects and politically driven decision making exerted pressure on the project timelines, completion dates and budget. The pressure for on-time or even early project completion- to avoid liquidated damages or achieve bonus payments, respectively- along with cost reduction efforts and the incentive for innovative failure events. That, in turn, put additional pressure on the Insurance market which had experienced a significant amount of losses with substantial cost. One of the triggered mitigation actions was the introduction of the Code of Practice for Risk Management of Tunnel Works (ITIG, 2006 & 2012; MunichRe 2006, Wannick, 2007, Spencer, 2008, Adeyemo, 2011)."

Jan 1, 2016

By Brendan Donnelly, Jung-Hoon Sul, Lasitha Piyathilaka, Sanghyun Jeong, Benjamin Probyn

The chains of armored face conveyor (AFCs) are constantly in contact with water and wet coal, which results in a significant proportion of unplanned downtime experienced on longwall equipment due to corrosion. While reverse osmosis (RO) is one of the most prevalent water treatment methods for reducing salinity and dissolved solids in coal mining, its impact on the corrosion of the AFC chains has not been well studied. This work studies the direct effects of RO water on the corrosion of AFC chains. Immersion tests followed by surface micromorphology analysis and corrosion indices indicate that the RO water increased the corrosion rate of the AFC chains due to the reduced tendency of preventive films on the chains.

May 1, 2024

By Edward S. Hsia

Pluor Utah has been closely associated with the engineering and construction of earth bottom thickeners for porphyry copper operations, for the counter-current decantation circuit of a gold cyanide plant and similar applications in mineral processing. During the past 13 years, some 18 of these thickeners have entered service and the bottoms have proved to be watertight structures with no particular problems encountered. In the course of this work, technological advances have been realized in the procedures for engineering and construction of these units to assure watertight basins and achieve all possible economies in construction. This paper describes the successful application of engineering and construction techniques for a number of these thickeners.

Jan 1, 1977

I met Austin Taylor in Vancouver on my way home from my first Pioneer examination. He asked me to examine the unsuccessful old Lorne mine, adjoining and west of the Pioneer. I had no idea that this meeting would lead to one of the outstanding successes and pleasant associations of my career. I knew nothing of Taylor, except that Gen. McRae and associates said that he had been engaged in lumbering and was interested in an oil and gasoline marketing company called Home Oil. But even if the Lorne examination would be only a small one, in the depths of the Depression in 1931, I was glad to have a chance to look at another gold property, so I agreed to visit the Lorne early in August. The start of the trip was not auspicious. I had been working hard on an unproductive study, and was greatly worried by my father's hopeless illness with tuberculosis. To get a little rest on my way north I had arranged to go from Seattle to Vancouver on the night boat that connected with my train. To my surprise, Bill Boultbee, an associate of Taylor, met me at the train in Seattle at 9:30. He said he would drive me to Vancouver, arriving at one In the morning. I was so tired that I begged off and let him take the drive alone Boultbee was most understanding and friendly, but I knew how I would have felt if I had been kind enough to take the long drive to help a stranger and then had been forced to make the return midnight drive alone. I was lucky they did not call off the examination at once. I got a good sleep on the Vancouver boat and Austin Taylor met me at the Hotel Vancouver for breakfast. After a brief talk he took me to the small steamer that made the 4-hr sail up Howe Sound to the village of Squamish. This was the end of the Province-owned Pacific Great Eastern Railway that was eventually to be a shortcut from Vancouver to the Canadian National main line at Prince George. Because

Jan 1, 1976

By Norman L. Weiss

The full importance of tailings disposal is yet to be realized by the mining industry, but our awareness of its present and future implications is growing faster, perhaps, than any single phase of ore processing. Few engineers can look very far into the future because of the complexity of the problems that may confront us if we project from the general indifference of past years through what we are already being expected to correct in existing operations, to confrontations with new statutes and an awakened public in any new plants hence- forth. The mistakes of the past have not been limited to the United States nor even to other countries of the Western Hemisphere. Indeed, all continents and subcontinents have suffered from myopia in releasing the tailings without retaining responsibility. However, the US as one of the world's great leaders in technology has a particularly unimpressive record. It may be safely generalized that the degree of control applied to the tailings of a milling operation has depended upon several factors more important than national boundaries. Thus in arid and semiarid climates no incentive was needed other than the scarcity of water to create a permanent and stable lodgment for mill tailings. On the other hand. where water has been plentiful. the temptation to let the tailings run into a river or lake or ocean (at least at certain times of the year) was often irresistible. So we find that modem tailings disposal in the southwest deserts of this country, with one or two notable exceptions where very serious breaks seem to occur at regular intervals, is satisfactory according to the standards of the 195QF and 1960s. while in various operations in Idaho, Michigan, western Colorado. Newfoundland, and elsewhere the record has been less praiseworthy. In the same way, cyanide plants which did not concern themselves about leakage, seepage, spillage, or wastage of tailings pulps with solutions containing toxic levels of free or combined cyanide soon heard a demand for better control. In consequence the industry has seen a growing use of cyanide regeneration of tailings or wash solutions, elimination of leakage, and careful structuring of tailing dams. The chemical and thermal qualities of tailing waters have occasionally been a spur to good tailings management. Some tailings disposal problems for example, the southeastern Florida phosphate clays and the Bayer red muds-have been given the intensive study they merited, but not always with much success.

Jan 1, 1985

By R. A. Williams

Surface and electrochemical techniques have been used to describe the surface chemistry of ferrosilicon powders, as a function of pH and electrochemical potential, for conditions typical of operating DHS plants. The practical consequences on the likely corrosion behaviour and associated electro- kinetic particle-particle interactions (which affect stability to sedimentation) in the suspension, are discussed.

Jan 1, 1987

By Z. Hladysz

It is common to nine a coal seam affected by previous extraction of a coal seam below. As a result of that severe problems may occur during the extraction process. This paper presents the analysis of undermining effects based on field observations. A simplified method for the evaluation of risk in undermining operations is presented and predictions of the degree of possible damages to the undermined coal seam is given.

Jan 1, 1985

By Denis McDermott

This paper describes the process used at three mines to devel­op safety and training programs. The mines are located in Australia, New Zealand and the United States of America. The aims of the programs were to promote and reinforce safe and healthy behaviour, increase productivity and efficiency and to provide a fair and objective basis for the payment of wages. There were common aspects to each of the projects: • mandatory legislation required employers to provide employ­ee training in work performance • employees had little previous involvement in the design and development of the training provided • training had been unstructured with employees relying on the "buddy system" to acquire new skills; the degree of skill acquired by an employee depended on the knowledge and teach­ing capacity of the worker to whom the novice was assigned • appointments and promotions had been based on judgements by supervisors and these were not generally understood by employees • employment conditions for employees were covered by an industrial agreement between management, unions and employ­ees. The degree of sophistication of the industrial agreements varied however none provided a description of work performed in each classification, nor the career or promotional path for an individual • supervisors with the responsibility to train, develop, motivate and reward employees expressed concern that there were no structured processes ( eg work standards or wage progression cri­teria) to support their role.

Jan 1, 1998

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

This United States Bureau of Mines study is based on a review of U.S. mine fire accidents that occurred from 1970 through 1989. Information on these accidents was obtained through investigative reports written by Mine Safety and Health Administration personnel. For this study, 260 mine fire accident reports were examined. A previous Bureau research effort established that fires causing fatalities were more likely to occur in haulage entries than at any other underground location. This study has found that the most prolific source of haulage entry fires was the inadvertent grounding of trolley wires. The largest segment (15 out of 40 trolley wire fires) resulted from not maintaining adequate clearance between the trolley wire and the vehicle. Several novel fire prevention and control ideas have evolved in response to frequently occurring fire-related problems. These included; discriminating power isolation devices, wire cutting devices, more accessible fire extinguishers, vehicle overcurrent protection, and vehicle fire suppression.

Jan 1, 1994

By K. N. Santini

Natural zeolites are gaining recognition as an important commodity with an increasing number of industrial and consumer applications. This potential has prompted the Anaconda Minerals Company and other firms to investigate occurrences and markets for zeolites. The deposits of mordenite-rich tuff at Rome are of interest for their economic potential and for the excellent opportunity they provide to study a zeolite deposit formed in a hydrologically closed basin. Location The Rome property is located approximately 9 km west of Rome, Oregon, in Townships 31S. and 32S., Range 41E., Malheur County. It lies within the Owyhee Uplands of the northern Basin and Range physiographic province (Figure 1). The area discussed here includes a major portion of the depositional basin in which the zeolitic tuffs occur.

Jan 1, 1982

By Jiachen Wang, Nan Wang, Yang Li

The close-multiple coal seam is an important component of China’s coal resources and plays a key role in total coal reserves. However, the overburden movement in the mining process of close-multiple coal seams is usually extensive, which is seriously affected by overmining. It is therefore essential to study the mechanism of roof breakage, the relationship between the shield and the surrounding rock, and the mechanism of overburden movement to ensure the safe operation and the efficient exploitation of close-multiple coal seams. This work first proposes a technical route for intelligent ground control. Second, the principle of cooperative control between the shield and overburden roof is revealed, and the shield support capacity calculation method is summarized. Third, the quantitative criterion for disturbance degree of key stratum (KSDD) is proposed based on the key strata theory. Finally, several intelligent evaluation and analysis systems have been developed in terms of overburden breakage and shield support capacity, multi-information analysis of ground control, and disturbance degree of overburden. The research results may provide an essential reference for the development of intelligent ground control in the mining process of close-multiple coal seams

Jul 1, 2023

By Norbert Patzelt, Johann Knecht

INTRODUCTION Grinding mills have been used in the minerals processing industry for over 100 years. Their dimensions have grown continuously during this time. Besides increasing throughput rates of grinding plants due to the depletion of high grade ores, the lower specific in- vestment costs, as well as reduced operating and maintenance requirements are major reasons for this trend. When selecting new plant equipment one must consider that design principles which have proven their reliability on sizes of today's equipment do not automatically warrant a successful operation on the ever larger size of equipment. Modern calculation methods as for instance the Finite Element method already contribute considerably to the safe design of the huge equipment being built today and are a standard tool of the design engineers. More recently, modern computer programs are also being used in order to size the equipment to meet the process requirements. Today, two design principles are on the market - one which supports the weight of such a unit on trunnion bearings through cast conical endwalls and one which is supported through slipper pad bearings arranged at the circumference of the mill shell (Fig.1). The reason for the development of this alternative grinding mill design can be found in the past. During the sixties and seventies the growing sizes of ball mills with high LID ratios caused many mill failures due to cracked endwalls. The accuracy of the calculation methods as well as the quality standards for castings were not developed to a degree required for such kind of heavy equipment. One way to overcome these problems was the increase of the manufacturing quality standards as well as the introduction of the finite element method based on the analysis of the experience available. The biggest grinding mills being built today are large size SAG mills with cast conical endwalls and trunnion bearings (Fig.2). This is due to the fact that mill manufacturers who had come from the conventional ball mill design adopted these principles as well to their SAG mills. These grinding mills perform well without special concern to the operators. Other manufacturers overcame the problems as mentioned above by eliminating completely the heavy castings and trunnion bearings and the problems associated to it (Fig.1). This design was originally applied to ball mills for the mining and other industries. Due to the success of these shell supported ball mills, this design principle was also applied to SAG mills(Fig.3). Despite of the fact that the majority of today's grinding mills are built to the conventional design it is also interesting to have a look at this alternative. Principles which have proven their reliability on sizes of today's equipment do not automatically warrant a successful operation on the ever larger equipment if bigger mill sizes are realized only based on the pantograph principle. With growing grinding mill sizes, the mass and volume flows through the equipment increases rapidly. Thus it is very important not only to concentrate on the safe design of the structural components of the equipment but as well on the process requirements. The influence of the design on important process parameters of dry and wet grinding plants are discussed thereafter. It shall be shown how modern computer programs can assist in the optimization of the design of components in order to fulfil the operational requirements of such large size equipment. PROCESS REQUIREMENTS OF LARGE SIZE GRINDING MILLS Dry Grinding Mills The world's biggest ball mill is a dry grinding ball mill having a diameter of 6.2m and an overall length of 25,5m with a drive power of 11,200 KW or 15,000HP. This grinding mill dries and grinds gold ore at a rate of 500 tons per hour at a moisture content of up to 9,5%. As shown in Fig.4 this mill was built as a shell supported unit. In fact only this design principle allowed to meet the process requirement. This mill could hardly be built with cast conical endwalls due to the constraints of the trunnion bearings limiting the mill inlet. The following case shows how modern computer programs can help to meet the design criteria of the air system of large size dry grinding plants. For dry grinding plants, the gas flow through the SAG mill has to match the drying, as well as the material transportation require-

Jan 1, 1998

By John W. Straton

Following the completion of the paper presented in February, 1972, data were received from many other mines and some original respondents submitted more complete questionnaires. The computer program was changed to permit the results to reflect more clearly all the data reported by the mines. The original paper was revised to reflect the new information. There were significant changes in some numerical values, particularly where the size of the sample changed appreciably. Some limited samples considered originally in arriving at conclusions were not relied on in this revision. The revised tables and text are of the same design and format as the original paper.

Jan 1, 1972

By R. L. Eppley

The Blacklick Creek Watershed Association was awarded a $158,000 Growing Greener grant from the Pennsylvania Department of Environmental Protection in 2002 for the design and construction of a sulfate reducing bioreactor (SRBR) cell to treat acidic discharge from the Judy 14 abandoned underground coal mine near Indiana, PA. The vertical flow SRBR was designed to treat 38 liters per minute of MIW containing elevated concentrations of aluminum and iron. Other treatment systems at this site plugged due to aluminum precipitates; this problem did not occur in the SRBR. The bioreactor has been periodically overloaded with flows up to six times the design rate. To date, the only maintenance performed on the unit has been the addition of hay to the surface of the unit in response to less than expected performance. The periodic hay additions appear to have restored the SRBR to nearly post-construction levels. Since construction, the SRBR has treated about 136,000 cubic meters (36 million US gallons) of MIW.

Jan 1, 2010

By Enrique Levy

Central America is graduating this year into large scale mining with the start up of Inco's multi-million dollar nickel laterite processing plant in Guatemala. In the other extreme of the Isthmus in Panama Texas Gulf Sulphur is doing check diamond drilling and foundation test drilling at the Cerro Colorado copper porphyry. The higher price of gold and silver has spurred development and exploration of several small precious metal mines. The purpose of this presentation is to make a brief resumé of the most important mines operating in the area and a list of significant exploration projects. Also, tables will be shown to compare mining codes and taxes. Unfortunately these tables lack information on Panama. Before starting I like to express my appreciation to Kennecott Copper who permitted the use of some of the data compiled by the author on their behalf during the year 1975. Other persons which did not want to be named also have my gratitude.

Jan 1, 1977

By P. A. C. De Ruiter

The Lower Cretaceous salt deposits of the Gabon Basin and Congo Basin were said down on ton of an Burly Cretaceous Lato Jurassic, continental graben fill that represent!) the rifting phase of the Afro-American continent. The salt 13 characterized by high percentages of potash and magnesium salts and the scarcity of sulphates and carbonates. The salt probably originated from a brine that was already enriched in high-soluble salts before entering the Gabon Congo basins. Their low-solubility equivalents are found in the Cuanza Basin of Angola. Commercial mining of the potash salt is only possible in those onshore areas where it is essentially undisturbed, shallow and of the right chemical composition. These conditions are net in Congo where the Holle mine produces from rich sylvinite deposits.

Jan 1, 1978

By Kyle Kittle, Kyle Knaeble, Albert Ruiz, Gregory Raines, Ryan Gewargis

The Chimney Hollow Reservoir Project (CHRP) is located southwest of Loveland, Colorado. CHRP is a component of the Windy Gap Firming Project, operated by the Municipal Subdistrict of the Northern Colorado Water Conservancy District. The inlet/outlet tunnel (IOT) for CHRP contains a reinforced concrete lined alve Chamber with PC membrane waterproong that was ecavated via seuential ecavation method to a diameter of feet. The IOT was ecavated using both drill and blast and road header with ground support consisting of steel sets, rock bolts, wire mesh and shotcrete. The IOT will withstand 300 feet of water head and rock ll surcharge load from the dam embankment constructed over the tunnel.

Jun 23, 2024

By A. Kalogeropoulos, T. Michalakopoulos

The DEM has been used in several studies to numerically simulate the response of rocks to the cutting action with drag tools. In this research, the aim is to realistically simulate the rock material and the cutting process by controlling the grain interlocking of the numerical assembly and streamlining the calibration process while focusing on the cutting force and the failure mechanism.

Apr 1, 2023