Search Documents

By R. M. Wilson

Concentrating plants, in common with other types of industrial plants, cannot operate without lectric power. The elctric distribution system and utilization equipment; therefore, must be carefully considered in all phases of plant design. Two important aspects of proper distribution and usage of electric power are the selection of voltage levels and the methods of system grounding. These are not necessarily the most important design considerations, but are perhaps more controversial than other major points, Modern plants demand increasing amounts of power which, since electric power is the product of voltage and current means higher voltages or currents. Higher voltages require more insulation, higher currents more conductor. The equipment designer?s problem is to obtain in his transformer, cable, switchgear, controller, motor, etc a balance of insulation and conductor to obtain a satisfactory design at lowest cost. To provide the most economical system, both in initial and operating costs requires the system designer to select the proper voltage level. Adequate voltage also permits expansion to meet future requirements, and results in better operation of utilization equipment, Relatively little advancement has been made in recent years in improving conductors; however, great progress has been made in improving insulation. Thus modern plants, in general, now find it more economical to use higher voltages than they did previously. For example plants which only a few years ago would have used 2400 volts as a system voltage often find nowdays that 4160 volts is their proper choice. If the plant requires 10,000 kva br more, then an even higher voltage, such as 13,800 volts, will prove economical. However, for the average concentration plant, with less than 10,000 kva demand, the choice of distribution voltages is between 2400 and 4160 volts, and 480 volts will be used for the low voltage utilization system.

Jan 1, 1958

By F. Ikumapayi

In order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the influence of major species, calcium and sulfate in process water on sphalerite flotation was investigated through Hallimond tube flotation, zeta potential, diffuse reflectance Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements using sphalerite mineral sample. Assessment of process water species in flotation was done using deionized water, process water and simulated water containing calcium and sulfate ions in experiments. Hallimond flotation shows increased sphalerite float-ability in process water compared to deionized water, but no significant effect on the presence of calcium and sulfate ions in deionized water using isobutyl xanthate as a collector. The presence of calcium ions reduced the sphalerite?s negative zeta potential, while at higher concentrations, a charge reversal occurred, at about pH 11. FTIR and XPS studies revealed the presence of surface-oxidized sulfoxy and carbonate species on sphalerite at pH 11.5 in deionized water, process water and water containing calcium and sulfate ions. These surface species do not influence xanthate adsorption.

By E. Topuz, C. Patrick

Longwall face-to-face equipment transfers or moves are the largest source of nonproductive time in a long wall-mining system. Detailed planning and resourceful thinking are paramount for economical, safe and timely longwall moves. New equipment and innovative techniques are frequently tested to reduce overall more time. Determining the cost-effectiveness of these ideas is difficult since the decision is influenced by many subjective factors. A project scheduling simulation model of the longwall move process was developed to analyze and assess the economic viability of innovative transfer methods and equipment. The model provides a project-duration frequency distribution and lists of critically indexed activities and paths. It compares the monetary savings from reduced transfer time and capital costs for several ideas.

Jan 1, 1996

By John K. Adams

Phosphorus may be incorporated into sedimentary rocks in at least four different ways: (1) by the accumulation of detrital mineral fragments, (2) by the accumulation of phosphatic organic debris, (3) by diagenesis and (4) perhaps by the primary precipitation of calcium phosphate. Based-on the petrographic examination of Cretaceous and Tertiary sediments from the northern and central parts of the Atlantic Coastal Plain, Diagenesis is the most important of these mechanisms. Both syndiagenesis and epidiagenesis are required to explain the origin of all the diagenetic phosphate mineral species which occur in the northern and central parts of the coastal plain. Syndiagenesis produced much of the coastal plain's apatite. It was operative below the sediment-water interface while the substrate was being compacted. Compaction forced pore waters, which were enriched in phosphate by the decomposition of organic matter, upward through calcareous sediments. The PO43- radicle replaced the CO23- and calcareous nodules, pellets and shell fragments were converted to apatite. Epidiagenetic reactions occurred in the subaerial environment where downward percolating meteoric waters carried phosphate in solution to cites where cation activity was sufficiently high to form new minerals. Vivianite may form where ferrous iron is available and wavellite and variscite may form in the presence of aluminum rich minerals. Textural evidence suggests that many of the reactions were repeated. The present day appearance of apatite, vivianite, wavellite and variscite in the coastal plain may represent several generations of diagenesis.

Jan 1, 1972

By R. P. King

Knowledge of the behaviour of flotation machines had developed and increased considerably over the last few years. Although much work remains to be done on the study of the fundamental processes that influence the collection of hydrophobic particles at an air-water interface, there is enough information to permit the building of realistic models of the gross flotation behaviour of various ores. These models serve as an ideal base for the development of simulation techniques for the steady-state behaviour of entire flotation plants that consist of a large number of individual flotation machines. Simulation techniques have a very real role to play in assisting with the design of new plants and in improving the operation of exisiting plants. Recently, highly efficient data-logging systems have been introduced on flotation plants. These systems are based on the on-line measurement of volumetric flowrate, pulp densities, and metal contents, and they generate enormous quantities of information regarding the operation of the plant. Unfortunately, this information is largely wasted at the present time because efficient data-reduction techniques, although available10 are not in common use. Simulation techniques play a central role in such data reduction because they form the essential link between the fundamental kinetic flotation processes on the one hand and the plant data on the other.

Jan 1, 1974

By T. E. Wilson

The length of Alaska's coastline, combined with the presence of a significant number of fjords, encourages consideration of marine disposal of mine tailings. However, the decision-making process is complex because various factors govern the viability of the submarine tailings disposal (STD) option. An expert system, called the Submarine Tailings Disposal Expert System (STADES), was developed to help mining project planners explore the feasibility of STD. A review of the existing literature, supplemented by engineering recommendations, on the various aspects of the marine disposal of tailings formed the knowledge base for the expert system. The shell used to develop the expert system was LEVELS.

Jan 1, 2003

By R. E. Scheffel

In February, 1976, Ranchers Exploration and Development Corporation obtained an option from Foote Minerals, Inc., to evaluate reprocessing of two uranium tailing piles. Foote received ownership of the Naturita and Durango tailing piles in 1967 through the purchase of Vanadium Corporation of America. The option was exercised in November, 1976, after initial testwork proved that a viable extraction technique existed. Preparation for production at Naturita began immediately with engineering and en¬vironmental permitting proceeding simultaneously. Production began in December, 1977, just 22 months after acquisition of the property and-was completed 17 months later.

Jan 1, 1981

By Robert W. Bruhn

The prediction of damage to a structure that is to be undermined is generally a two step process. First, the expected ground movements (the displacements, slopes, curvatures, and strains) are estimated using available (often empirical) predictive methods or survey data from a site of comparable geology, topography, and mining geometry. Second, the prospects for damage to the structure are assessed by comparing the expected ground movements to tolerable limits, some of which appear in the technical literature as damage criteria. The inverse problem of relating observed building damage to causative ground movements involves essentially the same elements. In either case, the usefulness of published damage criteria to subsidence problems may be limited in all but the most elementary cases. This paper considers several cases where structural behavior and site specific details had to be taken into account in assessing the relationship between damage and ground movements.

Jan 1, 1986

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017

By U. Paschedag

Today's modern longwalls have to produce high outputs with maximum availability and running time with the additional requirement of ever increasing panel width and length high-performance face conveyors require intelligent solutions for the integration of drive systems and chain tensioning devices into the overall longwall automation. The fully automated chain tensioning system allows the operation of an AFC with optimum chain tension at all times regardless of actual load on the conveyor. For the heavy-load start-up, the accurate load-sharing and an efficient overload protection of modern AFC's WESTFALIA and Dodge jointly developed the integrated WB/CST drive system.

Jan 1, 1995

By J. A. Ehler

Speed and torque control of standard A.C. induction motors can be accomplished using a variety of devices ranging from mechanical, hydraulic, and electrical. Also, the motor can be specified as an A.C. wound rotor or D.C. motor using the associated controls. Normally, any one of these drive types can be adequately used to provide the torque control necessary to accelerate a conveyor belt system. The selection will depend on the economics, experience, and preference of the designer or end user. These drive types will be presented from a functional and performance viewpoint to assist in the understanding of the available technology.

Jan 1, 1998

By J. Peterson, R. Michael, D. Yantek, E. Ferro

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. To address this problem, the U.S. National Institute for Occupational Safety and Health Office of Mine Safety and Health Research (NIOSH OMSHR) conducts research to reduce the noise emission of underground coal mining equipment, an example of which is the roof bolting machine. Field studies show that, on average, drilling noise is the loudest noise that roof bolting machine operators would be exposed to, and it contributes significantly to the operators’ noise exposure. OMSHR has determined that the drill steel and chuck radiate a significant amount of noise during drilling. OMSHR and the Corry Rubber Corporation (CRC) have developed a bit isolator that breaks the steel-to-steel link between the drill bit and drill steel and a chuck isolator that breaks the mechanical connection between the drill steel and the chuck. This effectively reduces the noise radiated by the drill steel and chuck and in turn reduces the noise exposure of roof bolter operators. This paper documents the evolution of the bit isolator and chuck isolator. Laboratory testing confirms that production bit and chuck isolators reduce the A-weighted sound level generated during drilling by 3.7 to 6.6 dB.

Jan 1, 2011

By M. Portal, L. Goicochea

This study is carried out in the Zenit mining concession, which is located in the city of San Pablo in the department of Cajamarca in Peru. The Project has 33 mineralized structures and according to laboratory analyzes we have the presence of gold and silver. The geostatistical evaluation provides an analysis on the distribution of precious metals in the vein. This information is used to improve the efficiency of metal extraction and to reduce costs. The general objective is to evaluate the polymetallic veins (Au and Ag), for which the classification of resources (measured, indicated, and inferred) has been carried out, taking into account the parameters of minimum distance from the composite, corresponding volume and tonnage calculation. In addition, an inventory of estimated geological resources was carried out with the block grades obtained to generate the tonnage-grade curves.

Feb 1, 2024

Power plants that utilize conventional wet flue-gas desulfurization methods produce enormous amounts of flue-gas scrubber sludge. A typical 400 MW power station that burns a high sulfur coal produces 170,000 tons of wet flue-gas scrubber sludge per year. This scrubber sludge is currently landfilled at an enormous cost to utility companies. This material could be used as a raw material for industries that use gypsum, such as the wallboard and plaster industries. However, before it can be used as feedstock for these industries, some of the impurities such as unreacted limestone and silicates must be removed from the scrubber sludge. Froth flotation has tremendous potential for separating these impurities from scrubber sludge. In order to select an optimum flotation process, it is necessary to characterize the surface properties of the major components in the scrubber sludge, which consist of calcium sulfite, calcium sulfate, calcium carbonate (limestone), and silica. In this study zeta potential measurements were used to determine the surface charge of the components in scrubber sludge, with the goal of optimizing a froth flotation process to produce a marketable gypsum product for the wallboard and plaster industries.

Jan 1, 1996

By Alastair R. Biggart

ABOUT BENTONITE TUNNELLING Much has been written and many learned papers given on this subject whose generic term is Slurry Tunnelling. This paper is about the particular form of slurry tunnelling known as the Bentonite Tunnelling System. This method. of tunnelling was invented by J.V. Bartlett of consulting engineers, Mott Hay and Anderson in 1964. The general principles are incorporated in British Patent No. 1083322. It was not until the early 1970's that serious experimental work was started to prove the technical feasibility of the process. In the U.K. in 1971 Edmund Nuttall Limited started on an experimental length of 3.8m diameter tunnel at New Cross in London. In Germany at about the same time Wayss and Freytag were starting on a 3.7m diameter collector sewer tunnel in Hamburg. In Japan early slurry tunnelling work was carried out in the 1960's. In the early 1970's a large number of slurry tunnels of various diameters were carried out in that country. This paper is being presented at a time when this system of tunnelling has become an accepted method throughout the developed world. As a result of the work carried out so far there is now a large amount of data existing regarding the effects on the ground in the immediate area of the tunnel, settlement at the surface and the ability of the system to cope with ground varying from clays to coarse gravels and containing large erratics such as granite boulders. The decade of the 1970's has therefore seen a very rapid pace

Jan 1, 1979

By K. Sasaki, H. Miyakoshi, K. Mashiba

A ventilation analytical system adapting nodal pressure method using skyline modified Choleski's decomposition scheme for network-flow analysis and a new practical system to estimate various thermal air conditions has been developed. The quasi-linear equations for solving steady-state network airflow have been described using the connective function in general forms. The skyline modified decomposition scheme has an advantage on rapid convergence and the sake of computer memory space com- pared with other schemes. The key part of the analysis for climatic conditions through network airways is how to estimate the temperature of the airway rock-surface with partly or full wet condition. A practical and simple solution without any iterative calculations for its estimation has been proposed. This new solution is applicable to practical ranges of airflow temperature, humidity, rock thermal properties and wetness. The present analytical sys- tem have been successfully applied to a ventilation simulator named "M1VENA"developed by authors.

Jan 1, 1996

By B. J. Arnold

Froth removal rate is perhaps the most important parameter in scaling up from laboratory tests to plant froth flotation circuits. The WEMCO froth factor, the percentage of the froth height over the lip of the cell, accounts for the difference between laboratory and plant froth removal rates. As laboratory tests are generally run with a high pulp level, laboratory results are directly comparable to plant results only when a high froth factor (high pulp level) is run in the plant. When a plant does not have a high pulp level, laboratory results must be modified by using a ratio between laboratory and plant kinetics to predict plant results. This ratio, which accounts for the froth factor is important in testing any new reagents or reagent dosage levels. CQ Inc. researchers have used predictive scale-up equations using this froth factor coupled with equations for kinetics and the residence time distribution in the froth flotation cells. These equations show that modifying the froth factor in the plant can have a large impact on flotation cell yield and reagent use. EQUATIONS DESCRIBING FROTH FLOTATION Scaling up from laboratory- to plant-scale coal froth flotation has been the subject of much research and debate over the years. Determining the proper rate equation to describe flotation kinetics and an equation to describe the residence time distribution in a bank of flotation cells have been particular areas of study. As shown in Tables 1 and 2, various rate equations and residence time distribution equations have been proposed in the literature. These equations consist of one or two parameters giving the rate constant(s) in units of time-1 and a parameter for recovery at infinite time, [Roo]. Dowling, Klimpel, and Aplan (1985) evaluated the rate equations in Table 1 for their ability to fit froth flotation kinetic data and found that all of the equations give reasonably low standard errors. Several of these equations, however, proved to have superior confidence limits for the parameters. Other equations have also been proposed to describe the recovery versus time profile. Most recently, Diao et al. (1992) proposed a first-order form with a sine wave distribution. As indicated in Table 2, investigators have suggested many equations to describe the residence time distribution in continuous froth flotation. To measure the water residence time distribution in a bank of cells, a soluble tracer is often used, with the level of tracer being measured over time at the tailings discharge. This response is then put on a dimensionless basis as described by Austin et al. (1984) in order to compare mixing behavior between cells or under different conditions. Coal flotation cells are generally of the flow-through or hog-trough variety allowing for some degree of backmixing and short-circuiting. While the water residence time distribution (see Figure 1) at the end of one cell in a bank of 1.4 cu ft WEMCO froth flotation cells may approximate perfect mixing conditions (Arnold, 1989), the water residence time distribution at the end of a bank of cells does not. Figure 2 shows the RTD for various flotation cell types compared to that for perfect mixers in series. To better describe the water residence time distribution in coal froth flotation cells, Van Orden (1986) used an equation similar to the perfect-mixers-in-aeries equation. This

Jan 1, 1993

By D. Wenstrup, K. Perry, J. Hatfield, P. Sainato, B. Lusk

Concrete-infused cloth is used in several civil and mining surface applications whose circumstances are similar to some of those in underground mining. A feature of this material is that it cannot be overhydrated. In underground conditions, however, the excess supply of water to the cloth for hydration could lead to muddy and potentially unsafe working conditions, as well as resource wastage by supplying more water to the construction site than is needed. The objective of this study is to verify the water-to-cloth ratio and study the effect of hydration level on the strength of the Concrete Cloth product. We found that the strength increases with increased hydration up to a 1:2 water-to-cloth ratio by weight, after which the strength holds steady regardless of additional hydration. This confirms the 1:2 water-tocloth ratio by weight for hydration and confirms that strength is retained even if the cloth is excessively hydrated.

Jan 1, 2014

By D. R. Zeni

Current mine development requires the safe, 'expedient, economical construction of vertical shafts for ventilation and access in diverse ground conditions. Advancements in large diameter shaft drilling have lead to exceptional mechanical refinements of shaft drilling technology. The author traces the history of the equipment and methods employed by the large diameter shaft drilling industry and explores likely paths of future development. A few case histories are cited to illustrate the adaptability of shaft drilling as a versatile tool for advanced worldwide mining operations. Safety, schedules, cost, environmental impact, and capability are discussed to assist the mining engineer in the investigation of feasible projects.

Jan 1, 1994

By B. W. Firth

Increasing depth in vertical mine shafts penalises conventional hoists in at least four distinct ways: rope weight becomes limiting; travel time increases; the obstruction of ventilation becomes more serious; and with friction drives, rope wear due to torque is aggravated. Travel speed is limited by instability of poorly sprung conveyances on inaccurately aligned flexible rails, and also by the cost of installed power to meet an inherently peaky demand. These problems call for a review of existing designs, firstly in respect of the furniture (Buntons and guides) obstructing the air flow, and secondly in regard to the hoist running in the shaft.

Jan 1, 1969