Search Documents

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By Peter Zhang, Todd Minoski, Gabriel Esterhuizen, Jack Trackemas, Berk Tulu, Morgan Sears

Longwall mining is a highly productive and efficient coal mining method used in the USA. During longwall retreating, the belt entry must be maintained stable, and any roof fall in the belt entry would jeopardize mine safety and substantially interrupt the continuous production of coal in the longwall face. Past experience of longwall mining has shown that belt entry stability was the greatest challenge in longwall ground control, and the occurrence of roof falls in belt entries was largely associated with high horizontal stress. To properly support the roof in the belt entry, it is important to understand how longwall-induced horizontal stress changes affect roof stability in belt entries and to strategically install supplementary support to prevent any potential roof falls. Researchers from the National Institute for Occupational Safety and Health (NIOSH) performed horizontal stress measurements in the immediate roof of the belt entries for two Pittsburgh seam longwall panels oriented unfavorably to high horizontal stress. Hollow inclusion cells (HICells) were installed in the immediate roof at the intersection in each of the belt entries, and stress changes were monitored as the longwall face was approaching and passing the intersection. Numerical models were set up to calculate the longwall-induced horizontal stress changes in the roof at the monitoring sites. With the verified model, investigations were made of how horizontal stress is concentrated and relieved in the belt entry roof near the face under different panel orientations. Both measurements and modeling results showed that high horizontal stress is concentrated in the roof in the belt entry within about 15 m outby the face when a longwall panel is unfavorably oriented to the major horizontal stress. The study demonstrated that longwall-induced differential horizontal stress can be used as an indication of the degree of horizontal stress concentration. Roof support strategies are discussed on how to maintain the stability of belt entry under high horizontal stress concentration.

Jun 14, 2022

By Bryant Fitch

This paper will review thickening theory, from the ( ) of the practicing engineer, with particular emphasis on ( ) uncertainty or disagreement. It will attempt to outline broadly what we know and what we don't know. This should serve two purpose First, it will warn the process engineer where he might get into trouble. At least it will alert him to the risk involved in uncritically accepting any of the recommended design procedures. Second, it will identify for researchers some areas in which further work might be fruitful. Not too many years ago there would have been little to write on such a subject. We had been designing thickeners for decades, using the classic Coe and Clevenger procedure. As far as we were generally aware, they all turned out to be about the right size. And so if there was anything we didn't know, It certainly wasn't hurting us much. Today we know better. While it is true that in most cases units designed by the Coe and Clevenger procedure (1) will perform satisfactorily, we now know of cases in which they don't. And during the past few years there have been many developments and advances in basic thickening theory. So there is now a lot more room for disagreement, and a whole lot more to be uncertain about. What is "thickening" "Thickening" means different things to different people. For this paper we define it to mean sedimentation behavior characterized by line settling. Solids subside with a clear line of demarcation between settling solids and supernatant. Although the supernatant will usually be clear, in some cases it may be turbid. Line settling must entail that all particles just below the pulp-supernatant interface have the same subsidence rate, so that

Jan 1, 1971

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969

By Timothy O’Rourke, Karrie Buxton, Chris Lynagh, Daniel Dobbels, Frederick Vincent

The Doan Valley Storage Tunnel Project in Cleveland Ohio was constructed to control Combined Sewer Overflows (CSOs). It is a complex system of three tunnels ranging from 8.5 to 18 feet in diameter with a total length of about 2.3 miles that was put into operation in mid-2021. The project lies within and below the cultural, educational, and medical hub of Cleveland, which presented unique design and construction challenges. This paper provides a case history of the design and construction, with particular attention given to lessons learned in devising a large tunnel system that can carry both dry and wet weather flows constructed in rock with limited cover, within a flood plain area and vibrant urban center

Dec 1, 2022

By Patrick McElhinney, Jacob Carr, Bruce Whisner, Cory DeGennaro, Jingcheng Li

Since 2016, electromagnetic interference (EMI) of personal dust monitors (PDMs) with magnetic proximity detection systems (PDSs) has been observed in underground coal mines. The EMI causes the magnetic field measurements of a PDS to change, which, in turn, alters the calculated location of the miner relative to the machine. Any altered location calculation can potentially cause the PDS to fail to warn a worker who is at an unsafe distance from the machine, arousing a serious concern on safety hazard caused by EMI in underground mines. The search for EMI mitigation strategies led to the development and use of large shielding pouches and boxes to hold the entire PDM to reduce its magnetic emission. Research on these pouches and boxes found that although they were able to reduce the emitted radiation from the PDM, they also disturbed the magnetic field of the PDS, affecting its performance. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have focused on shielding internal PDM components rather than shielding the entire PDM. The PDM air pump motor is one of the PDM components that has been identified as a major source of electromagnetic radiation and has been selected for further study and tests. The measurements show that a small copper or aluminum foil enclosure can effectively reduce the magnetic emission of the motor by between 50 and 85% at 73 kHz. This study compares the test results of the air pump motor with various cost-effective shielding materials. The data provided in this paper can serve as a reference for shielding enclosure design of the PDM air pump motor to reduce its electromagnetic emission as one form of EMI mitigation strategy.

By Robert Stefanko

Longwall mining appears very attractive from an engineering standpoint because of its simplicity. The use of one long, continuous face can simplify power distribution, ventilation, and supervision, and minimizes or prevents lost time associated with the tramming of equipment in room-and-pillar systems. Since the longwall system is more amenable to automation, it is inherently safer than room and pillar. Remote control of all face equipment from gate roads will obviate the exposure of men in the face area. Considering what has been said, it seems a paradox that more longwall installations are not found in the United States. However, with favorable mining conditions in relatively level seams of adequate height under shallow cover, it has been possible to develop highly productive, mechanized, room-and-pillar systems. Thus there has been no real incentive to employ longwall in the United States. In Europe, mining companies usually have very little choice between the two systems. Pitching seams of low height located at great depth dictate the use of longwall methods. With depletion of its readily accessible reserves, mining conditions will be similar to those now prevailing in Europe, and an increase in the use of longwall in the United States can be anticipated.

Jan 1, 1963

By Stanley J. LeFond

The Republic of Botswana, one of the newer countries of southern Africa, attained independence on September 30, 1966. It covers an area of about 225,000 square miles (582,000 square kilometers) which makes it slightly larger than France, or slightly smaller than Texas. It is bounded by Zimbabwe, the Republic of South Africa and Namibia, including the Caprivi Strip. Angola and Zambia are close neighbors. (Map 1). Botswana lies at the center of the southern African plateau at a mean elevation of 3,300 feet (1,000 m). It is a natural habitat for most species of African fauna. The rolling sands and extensive grasslands of the Kalahari Desert cover the southwest. The climate is sub- tropical. Summers, although tempered by north- easterly breezes, are hot, but mean maximum temperature seldom rises above 100°F (38°C). Winters are dry with wide temperature variations, which often give rise to frosts.

Jan 1, 1981

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By Dafydd Chandler, Milissa Hirst, Charles Hurst, Gary Snyder, Leszek Glodkowski

The Delaware County Regional Water Quality Control Authority (DELCORA) will be adding tunnel infrastructure to its wastewater conveyance system. This program involves the construction of a conveyance/storage tunnel and related facilities. The proposed 12- foot to 14-foot (±) finished diameter, TBM mined deep rock tunnel spans over 8.5 miles and lies approximately 80 ft-120 ft below the surface. The system is connected to the surface by at least five vertical online shafts and one offline shaft with associated 800ft long adit. This paper provides project details including data on the geologic conditions in which the tunnel will be constructed.

Dec 1, 2022

By J. H. Gwynne

[ ]

Jan 1, 1962

By Edgar O. McAlister

Associated with cordilleran intrusives of intemediate to acidic composition, gold/silver ores are generally found in the intruded host rocks which are adjacent to these intrusives. Generally precious metal deposits lie further from the intrusives than allied base metal deposits. For vented intrusives, the associated volcanics may constitute the intruded rock and form the host for precious metal accumulation. Potential field methods, particularly magnetics, can help to define unseen boundaries of intrusive systems and thus can point to generalized prospecting targets. Other clues arise from the intrusive system type, its emplacement fracturing, the host rock type and local magnetic changes caused by mineralization processes.

Jan 1, 1984

By G. Troly, M. Esterle, B. Pelletier, W. Reibell

In New Caledonia, ultramafic formations occur on 7,000 square kilometers. Weathering of peridotites leads to profiles of alteration and nickel concentrations. Complete profiles are composed of two main groups of horizons: 1. Limonitic, mainly composed of iron hydroxides 2. Saprolitic, partly composed of magnesium and iron silicates Shape and mineralogical composition of saprolitic horizons are chiefly affected by the nature of the bedrock: types of peridotite and their degrees of serpentinization. On the other hand, morphology (plateau, terraces, slopes, piedmont) is an important factor. Ore-bodies are inside saprolites; their outlines are determined by the grade of nickel and tonnage economically mineable. Information about geology, morphology, geochemistry, and mineralogy are given in this paper.

Jan 1, 1979

By J. F. Peterman, M. C. Roberts

The success of any industrial mineral project requires an accurate forecast of the demand fir the material as well as accurate projections of costs and prices. This paper develops a general method of predicting mineral requirements and applies it to the case of graphite. The basic method is to explain graphite consumption in each of its major uses by the output and manufacturing technology of the using industry. Once these underlying factors are determined, they can he projected to establish future requirements. This forecast is critical to the evaluation of a new source of supply, such as the graphite resources of Upper Michigan.

Jan 1, 1990

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The paper investigates the influence of slope height, slope angle, slope material, and rock size on rockfall runout distance in openpit mines. Using statistical analysis and simulation, the study aims to improve rockfall hazard assessment and catch bench design by identifying key variables affecting rockfall behavior.

Oct 1, 2023

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

Calcite has found many applications in the industrialized countries recently, such as filler for paper, paint, plastics, rubber and food. Furthermore, calcite separates many toxic elements, and thus it is used in water treatment, and it is also used to raise the pH of drinking water. Due to its special features, calcite has been characterized as a useful coating and reinforcement filler for applications. Finer particle size of calcite has been determined to provide improved features for all of these applications. For submicron particle production, wet milling is selected over dry milling to produce finer particle sizes. Wet stirred media mills are also used in many industries. For that reason, this study investigated the effects of operating parameters on particle size reduction in the wet grinding process. The knowledge acquired by this study will allow the finding of optimal operating parameters for a stirred media mill to optimize specific energy consumption and reduce particle size.

By A. M. Marabini, G. Belardi, V. Alesse, M. Acosta

Sotiel mine is situated in the Iberian Pyrite Belt in southern Spain, some 40 km north of the port of Huelva. Although mining operations at the site date back to Roman times, the present mine came into production in 1983 and 5.6 million tonnes of ore had been extracted by 1993. The orebody is volcano-sedimentary and consists of fine grained copper, lead and zinc minerals in massive pyrite surrounded by slates and volcanics. Prior laboratory research had resulted in the synthesis of a new collector, belonging to the MercaptoBenzoOxazole (MBO) class that acts selectively towards Cu and Zn minerals after activation with CuS04. The MethylMercaptoBenzoOxazole (MMBO) version of this collector had been used for the laboratory flotation of Cu minerals and sphalerite activated by CuS04. This resulted in identification of the optimal physicochemical conditions for laboratory-cell flotation of the two minerals from samples of complex sulphide ores, and subsequently the reagent has been tested in the Sotiel plant (Spain). The plant has three flotation sections. With conventional re-agents, the first section yields a Cu concentrate grading 21% with a total recovery of 29%, and the second one yields a 40% Pb concentrate with total recovery of 34% and a 47% Zn concentrate with total recovery of 78%. Application of the new synthetic reagent in the copper and zinc circuits produces a more selective process with a decrease in re- agent concentration grade and recovery are increased by 2 and 9 points respectively in the case of Cu and by 1 and 3 points where Zn is concerned. Moreover, the penalty elements in the Cu concentrate are halved.

Jan 1, 1995

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By H. Russell, N. DePriest, J. D. Quaranta

Valley-fill structures built of blasted rock overburden from Appalachian mountaintop surface mines pose many reclamation challenges. The steep mountainous terrain, short valley lengths, and straight stream channel profiles create significant challenges to implementing fluvial geomorphic landform design in terms of both form and function, and from a safety and constructability perspective. The fluvial geomorphic landform design approach balances erosive and resistive forces by considering long-term climatic conditions, soil types, slope profiles and vegetation types. Commercial geomorphic landform design software tools do not specifically analyze the stability and factor of safety for the computer-designed landform slopes. This research investigated slope stability parameters and factors of safety between a traditional valley-fill design with a geomorphic landform alternative. Slope stability assessments were performed on two profile geometries. Finite-element modeling of a permitted valley-fill and a geomorphic design alternative indicated that slope angle and internal angles of friction associated with the gradation of the overburden greatly affected the designed factor of safety for both designs. The geomorphic designed slopes yielded the highest factors of safety out of 14 models analyzed with all cases having factors of safety over 2.0. The high factors of safety are attributed to shallow slopes and beneficial surface and internal drainage.

Jan 1, 2014

By Lee R. Martin, Michael R. Taber

Bird Balls™, the latest development in the ongoing battle at mine sites across North America, help to eliminate accidental avian mortality caused by birds ingesting cyanide leachate. Bird Balls™ are a 4-inch sphere made of high-density polyeth­ ylene (HDPE). They weigh 40 grams and are black in color to provide optimum life in UV intense environments. A floating blanket of bird balls totally excludes birds from a liquid surface. Federal agencies that enforce the Migratory Bird Treaty Act do not specify how to keep migratory birds out of leachate basins. Some state agencies, however, specify that a physical barrier must be in place to exclude migratory birds if cyanide levels are high enough to cause mortality. Industry standards for protecting waterfowl now include Bird Balls™ as well as net­ting, detoxification, and heap leach systems designed in such a manner that no exposed solution ponds or channels exist. Hazing is no longer an option. A bold statement to make? Perhaps, but W. R. Jeffress (1990) covers the subject well when he stated that, "Hazing techniques as a whole have not been effective in excluding waterfowl or other species of wildlife from toxic heap leach solution ponds or tailings impoundments. Research and devel­opment of the new 'Star Wars' hazing techniques, such as laser netting and radar systems, are interesting concepts and will pos­sibly offer an alternative to total physical exclusion or neutral­ization in the future. All of these methods are going to have to be thoroughly tested." For those who may want further docu­mentation, we have included a special reference section cover­ing hazing. R. J. Hallock (1990) stated that, "The Fish and Wildlife Service is particularly interested in migratory birds. In fact, a large portion of our effort, nationwide, is focused on migratory birds. Bird habitats are managed directly through the National Wildlife Refuge System and indirectly through other agency programs. We also have a responsibility to protect birds under the Migratory Bird Treaty Act. Most birds attracted to mine ponds are covered under this Act. The only migratory birds not protected under the Migratory Bird Treaty Act are English Sparrows, Starlings, and Pigeons. Since this is a treaty with five nations, the concept of acceptable losses does not apply. It is not a negotiable situation. There are a few exceptions noted in the Act, including prescribed hunting of selected waterfowl, scien­tific collection, and game bird farming. There is no exception for the loss of migratory birds exposed to solutions of cyanide."

Jan 1, 1996