Search Documents

By M. J. Gula, S. S. Xue, E. P. Horwitz

A study was conducted to remove iron from sulfate solu¬tions using Eichrom'sDipex®extractant, PP'-di(2-ethylhexyl) methanediphosphonic acid (H2DEH[MDP]). It was found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 106. More than 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 2000

By Nick Barton

The ability to estimate that support is unnecessary for various dimensions of opening in certain rock mass environments is of particular relevance in the mining industry, where most excavations are not expected to remain open indefinitely. As Hoek1 observes: "the basic aim of any underground excavation design should be to utilize the rock itself as the principal structural material, creating as little disturbance as possible during the excavation process and adding as little as possible in the way of concrete or steel support". Approximately two hundred case records have been analysed for the purpose of determining the amount of permanent support normally used when a given span is excavated in known rock mass conditions Some thirty cases concerned unsupported openings. Excavations that can stand unsupported appear to have certain common characteristics as regards rock mass quality. However, the mechanical properties of the rock mass are not the only factors controlling the choice of design. The dimension of the opening (span or height) and the type of excavation are two important variables.

Jan 1, 1975

By Godfred Amponsah, Mehrdad Razavi

Slope failures very commonly occur during a long period of heavy rainfall and groundwater rise. The failures pose a substantial risk to people, infrastructure, and equipment downslope. In the recent past, the mining industry has faced an increase in tailings dam failure due to several reasons including pore pressure increases in the dams. Many failures have been observed to occur during times of water level fluctuations but the critical factors that influence the initiation of slope failures still need to be adequately clarified. To investigate these factors, laboratory experiments were conducted on model sandy slopes to determine pore pressure-induced slope failure initiation. This study also presents a method to examine water seepage through soil slopes using an ultraviolet (UV) dye and a UV flashlight. The small-scale model test simulation demonstrated failures induced by either water percolation from the upslope tank at a constant level or by raising the water level at intervals. A bottom chamber fully filled with water to replicate groundwater rise was also simulated. The soil slope was monitored at every stage to study the deformations and behavior until failure occurred. Results gathered from the controlled laboratory conditions were useful for the verification of the numerical modeling method created in the computer program Slide. The analysis showed that slope failure always occurred when the toe was fully saturated. High pore pressures and seepage forces reduce the shear force at the toe to almost zero causing it to slide. A comparison of slope height to water level also indicated an average of 96% water level to cause a failure. At this point, the soil slope is fully saturated and has no matric suction. The findings in this study show that, by monitoring the moisture content of slopes, failures can be predicted.

Feb 1, 2024

By M. C. Radomsky

Approximately sixty, small, surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the safe standards of worker behavior and work conditions. Data were collected through the use of operation-specific, on-site safety records covering seven major occupational units. Workplace events observed (acts and conditions) were assigned a hazard classification; feedback, both immediate and delayed was initiated to improve safety performance. The experiences drawn from this pilot project have proven the need to continue to pursue this behavioral approach; however, a stricter methodology needs to be adopted in the collection and analysis of data.

Jan 1, 1987

By Dennis S. Kostick

Sodium is a silver-colored metal that is so unstable that it reacts violently in the presence of water, and chlorine is a greenish-colored gas that is dangerous and lethal. Yet the combination of these two elements forms sodium chloride, commonly known as salt, which is a white-colored compound essential to life itself. Salt is perhaps the only mineral in the world that is used virtually by every human being in every country. Although its importance has diminished over time, salt has had a profound influence on history. Sources of salt have determined the location of cities, such as Salzburg, Austria, Salzgitter, Germany, Salt Lake City, UT, and Saltville, VA. Populations have migrated in search of salt, and wars have been fought to obtain or to protect it. Although there is no written record of when prehistoric man first discovered salt, he probably instantly appreciated its unique and distinctive taste and sought more of it. He noticed animals were attracted to salt springs and salt licks, where they satisfied their innate cravings. Man used this knowledge to hunt for food; where he found the salt, he would find the animals. Because prehistoric man was not aware of his physiologic need for salt, he automatically received his salt requirements from the meat of the animals he ate. A Mesopotamian tale tells of a wounded pig that ran into the ocean and drowned. After being recovered from the ocean, where it was saturated in the salt brine, the pork was found to taste better than unsalted meat. It was not until man graduated from a nomadic to an agricultural society when he introduced vegetables and cereals into his diet that he realized he needed additional supplements of salt. The Sumerians ate salted meat and used salt to preserve food about 3500 BC. In approximately 1000 BC, the Trojans learned to use salt for preserving fish. The maritime civilizations, such as that of the Phoenicians, engaged in an extensive salt trade throughout the Mediterranean. Many superstitions, customs, and traditions surround the religious, social, economic, and political aspects of civilization. Although some commodities have provided the basis of some ageless metaphors and cliches (i.e., heart of gold, strong as steel, etc.), none are more commonly used than those pertaining to salt. Being "the salt of the earth" referred to a person's worthiness, as referenced in Matthew 5:13 of the Bible. Someone "not worth his salt" reportedly was used in ancient Greece in bartering salt for slaves. When a laborer was worth his salt, he was paid a salary (sal is Latin for salt), a term still in use today that dates back to Roman times when part of a soldier's pay was salt rations. Fearing those around him, the Roman leader Pompey was known to add a grain of salt to his drinks as a supposed antidote to poison. Hence, "taking it with a grain of salt'' is to regard something with suspicion. The earliest known record of salt production was in China about 2000 BC when Emperor Yu decreed that salt had to be supplied to the court as a tribute. Because salt was a commodity that had universal demand, governments often intervened to control salt production and distribution to generate revenue for major national projects. State-run salt monopolies were common in history, such as in Rome about 506 BC. Revenue was also derived from taxes levied on salt sales. The word gabelle refers to the direct salt tax used in France. This tax was so despised that it was a major cause of the French Revolution. Although the tax was repealed in 1790, it was reinstated in 1805 to raise revenue for war. France continued to used the gabelle until 1945. Salt making was an important economic activity in many areas of the world. Archaeological evidence indicates that salt was quarried from hills near the Dead Sea before the Bronze Age. At Hallstatt in the eastern Alps of Austria, rock salt was mined as early as 1400 BC. Solar salt was being produced in the northern Yucatan peninsula by the Mayan civilization from about 50 BC to AD 300. Other than the prehistoric use of salt in the southwestern part of the United States by the Native Americans, the first production of salt by American colonists began in June 1614 on Smith's Island, VA, seven years after the founding of the Jamestown colony. The short-lived activity was in response to the high price of salt being charged by ship's captains who brought salt over as ballast from England. Although Nathaniel Loomis is credited with starting the first commercial inland salt production in the United States at Onondaga Lake in New York in 1790, salt had been made by individuals for private use years earlier. Indians had long known of the salt springs in the Kanawha Valley of Virginia (now known as West Virginia). In 1755, Mary Ingles, a white settler, was kidnapped by Indians and was forced to make salt from the saline springs. After her escape, she told other settlers how to make salt. At Saltville, VA, Arthur Campbell began making salt in 1782 by boiling brine obtained from salt springs. In 1799, William King sank a shaft about 3 m in diameter down about 61 m to the underlying Saltville salt deposits. The shaft flooded before he could extract any rock salt; however, King has the distinction of digging the shaft of the first salt mine in the United States. Fig. 1 shows the King site as it appears today in Saltville, VA. Production of brine from the shaft continued until 1892. Settlers moved into the Kanawha Valley in 1785, but it wasn't until 1806 that Elisha Brooks established the first commercial salt works in Kanawha.

Jan 1, 1994

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

By Arthur Miller

Most of the production of copper in the United States comes from a few large companies. Often overlooked, however, are the more numerous small mining operations, which collectively produce a significant portion of the nation's copper. The objective of this paper is to describe the operations of a small mining company - Ranchers Exploration and Development Corporation - how it views its place in this industry of giants, how it exploits the advantages offered by its relatively small size, and how it protects itself from the hazards being small introduces. Environment is, of course, a critical factor for such a company because it does not have the resources which help large companies weather periods of financial stress. Ideally, this environment is characterized by a heal thy economy, strong product demand, relatively stable prices , adequate grades and tonnages of ore commensurate with depth and over-burden, ready access to utilities, a dependable labor pool, and suitable technical "know how". When the environment is right, properties which were previously uneconomical to operate attract the attention of companies whose primary interest is a return on investment commensurate with risk over a reasonable period of time. Naturally, the amount of the investment and the duration of operation determines the size of the company which would be interested in such a venture. Such is the case with Ranchers Bluebird Mine at Miami, Arizona - a small property operated by a small company in a favorable economic environment.

Jan 1, 1967

By Ted H. Eyde

Both private industry and the Interior Department have become alarmed about the enormous amount of Federal land that has been withdrawn from appropriation either under the Mineral Leasing Laws or the Mining Law of 1872. According to a recent article by Gary Benethum and L. Courtland Lee, governmental actions have withdrawn nearly 400 million acres from the operation of the Mining Law of 1872 and over 500 million acres from the Leasing Laws. An addition al 100 million acres for the Mining Law of 1872 and 70 million acres for the Leasing Laws are either encumbered or being managed in such a way as to constitute a defacto withdrawal from mineral development. This means simply that mineral exploration end development under the Mining Law of 1872 is either prevented or discouraged in an area the size of the states of California, Arizona, Washington, Oregon, Nevada, Utah, Idaho, and one half of Colorado combined. Under the Mineral Leasing Laws, exploration and development is either prevented or discouraged in an area equal in size to all the states east the Mississippi River, except Maine.

Jan 1, 1976

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

By Jennifer Gallagher

The Henderson molybdenum mine, near Empire, CO, has operated since 1976 using a panel caving process and a rail haulage transportation system. After two decades of service, the rail haulage system required a substantial capital expenditure to improve operations. The timing for this worked well because Henderson was able to combine this capital need into a mine plan that addressed process bottlenecks and current mining practices as a new production level was designed and developed. This process was a logical step, following an equipment upgrade program, and became known as the Henderson 2000 project. One of the key components of Henderson 2000 is a new ore transportation system. Throughout Henderson's life, the bottleneck has been the rail haulage system. Henderson staff evaluated several transportation alternatives and decided on a truck haulage configuration feeding an underground crusher and conveyor system. This configuration will eliminate the haulage bottleneck and will allow the mine to increase capacity. The installation of this system will be completed by the year 2000. The second key component of Henderson 2000 is the development of a new 7175 production level to extract the lower reserves of the ore body. Henderson staff benchmarked other caving operations and compared their mining practices to Henderson's basic mining guidelines. It became apparent that Henderson's practices could become more efficient, particularly in the areas of drawpoint spacing and column heights. These concepts were incorporated into the layouts

Jan 1, 1998

The current understanding of the mechanics of rock fracturing during smooth blasting is largely empirical and qualitative due to an inability to model the dynamic process at the fundamental level. In order to overcome this difficulty, a numerical simulation of smooth blasting is performed using the Dynamic Lattice Network Model. This model is capable of simulating material inhomogeneities and the dynamic evolution of fragmentation at the micromechanical level. In this study, smooth blasting techniques are numerically analyzed to characterize the development of the damage rock zone during explosive fracturing.

Jan 1, 1995

By D. F. Strong

Most Newfoundland. mineral deposits can be clearly classified as within rocks formed either as accreting plate margins (ophiolitic pyrite-chalcopyrite massive sulfides such as Betts Cove, Whalesback, York Harbour, chromite at Lewis Hills, and asbestos at Baie Verte), at consuming plate margins (Kuroko-type polymetallic massive sulfides such as Buchans and Pilleys Island, porphyry-type Mo-Cu at Rencontre, fluorite at St. Lawrence), or within plates (zinc deposits at Daniels Harbour, sedimentary iron ores at Wabana, manganese in Conception Bay.) As these metallogenic patterns can be convincingly extrapolated southward into the Appalachians and northward to the Caledonides, they provide an important means of eliminating and selecting areas for particular exploration targets. Sonic criteria are described for the recognition of these environments of differing economic potential.

Jan 1, 1973

By Greg Sanders, Bill Lueck, Michael Gilbert, Mahmood Khwaja

"The city of Minneapolis contracted with CDM Smith to update and provide a conceptual design for improvements to mitigate surcharge flooding in the Central City Storm Water Tunnel System (CCSTS). As a part of the project, CDM Smith conducted a field survey and condition assessment of the existing tunnel system. Information from the survey was then used to update the existing XPSWMM model and develop system wide alternatives.The CCSTS provides storm-water runoff drainage for nearly the entire area of the city’s downtown commercial district. The system consists of deep storm-water tunnels constructed in the St. Peter Sandstone, approximately 21 m (70 ft) below the street’s surface. The primary tunnels comprising the Central City storm water tunnel system are located below Hennepin Avenue, Nicollet Mall, Lesalle Avenue, Marquette Avenue South, 2nd Avenue South, South 5th Street, Washington Avenue South, Portland Avenue South, 2nd Street South, and Chicago Avenue South, as shown in Fig. 1. This network of tunnels conveys the runoff from a 305-acre tributary area that is generally bound by Hennepin Avenue and 1st Avenue North to the east, 12th Street to the south, 4th Avenue South and 7th Avenue South to the west, and 2nd Street South. These tunnels were constructed between 1936 and 1940, except for the Marquette Avenue South tunnel, which was constructed between 1963 and 1964.The CCSTS operates as a gravity flow system. These tunnels were constructed within the St. Peter Sandstone layer of bedrock and emerge from the bedrock at the Mississippi River below St. Anthony Falls. The Central City and the adjacent Chicago Avenue tunnel system converge into a single outfall at the Mississippi River. The runoff discharges from the converged outfall to a side channel of the Mississippi River, called a tailrace, located near the Guthrie Theater. The Minneapolis Division of Surface Water and Sewers provided 32 historic plats detailing the plan and profile of the tunnel system.The tunnel plans show nine different cross-section configurations. Eight configurations within the overall system generally show the same geometric “cathedral” shape with the inside dimensions varying from 1.2 to 1.8 m (4 to 6 ft) in width and 1.8 to 2.4 m (6 to 8 ft) in height. For analysis, these eight configurations were reduced to three configurations with regards to tunnel liner, cross-sectional area and support. For simplicity, the three configurations are described according to the three types of tunnel support used during construction: none required, light timber and heavy timber"

Jun 1, 2019

By James W. Echerd

Anthracite preparation developments, particularly in the early days of the anthracite industry, formed the basis for the modern coal preparation plants that have become so essential to the coal industry today. The anthracite industry, from early in the 19th century until relatively recently, was a leader in mining, preparation and marketing of coal, and played a leading role in the development of the industrial America we know today. Anthracite was discovered in America in about 1760--the story of Necho Allen is well known--but the rediscoveries leading to mining operations took place about 50 years later. The Wurtz brothers in 1815 at Scranton, the Smith brothers at Wilkes-Barre in 1807, Beach in Hazleton in about 1814, and Boyd in 1816 at Shamokin were all instrumental in promoting early mining and marketing of anthracite (J3. The early canals and railroads were built for the specific purpose of moving anthracite to the market areas. Eventually, the industry grew until, in 1917, it reached a production zenith of a little over 100,000,000 tons, representing about 20 percent of the total coal output in the United States. Almost half of the anthracite produced that year was consumed for domestic heating, a utilization that had dominated the industry for almost 100 years. Initially, anthracite had to be used by gunsmiths and blacksmiths, after which had followed the consumption of extensive quantities for railroads, blast furnaces and foundries, and electric power generation. Most of the markets have been lost to coke, oil, and natural gas. Near the anthracite regions, however, significant quantities are still used for domestic heating, power generation, carbon black manufacture, blending with bituminous coal to make metallurgical coke and fuel, and for other industrial purposes. Thus, anthracite production has not been entirely committed to history, but remains an active industry that follows modern practices in the mining, preparation, shipping, and utilization of a fuel that is still a valuable adjunct to the national economy. In fact, its inherent low sulfur content may make it an important fuel of the future. Estimates indicate there are reserves of anthracite to last for 300 years at a consumption rate of 50,000,000 tons/year. Anthracite Preparation Yesterday A 170-year history of the anthracite industry obviously is not the purpose of this discussion. A complete history of anthracite preparation, the rather unglamorous step in the processing of "mine run" hard coal to make it suitable for the user, is also not practical. Hence, the purpose of this report is to trace the development of some of the most important processes used through the years to meet a part of the demand for energy developed by our modern society. Anthracite preparation in the early days of the industry consisted solely of separating slate from the coal, by hand, underground (Z). This method prevailed for almost 20 years until wrought iron hand rakes were introduced to separate the large and small sizes. Shortly thereafter, the first attempts were made to size and clean the coal aboveground. The coal was dumped on a perforated cast iron plate, and men used sledge hammers to break the larger pieces into smaller sizes suitable for the market. The smallest sizes--that is, the material that went through the plate--were thrown away because they had no value at that time--a concept that existed for many years and actually was the basis for the subsequent "river" coal production and the many silt banks which are landmarks in the anthracite region. The larger sizes, at that time, sold for 50 cents per ton. The Batten breaker, or roll crusher, was invented in 1844, followed soon thereafter by the Snell-Diehm breaker (A). The latter had disadvantages, including excessive waste and fixed product size, but it later was improved in these respects. A breaker was also developed at Minersville, Pa., at about the same time that processed 200 tons of coal per day, using roll crushers and circular screens (1). Handpicking, from the beginning of anthracite preparation, was an important part of the cleaning process and was still being practiced as late as 1950. It was this process that involved the "breaker" boys of coal region lore. How much good handpicking accomplished depended on how much impurity was present in the coal--the more the impurities, the greater the reduction in ash. Thus, high-impurity streams were significantly improved, whereas picking of relatively clean coal was mainly to show an effort to make a quality product. As indicated, picking is largely a visual operation. It was and is wasteful of coal in the larger sizes since some good coal is always associated with the bad. However, it was probably much more effective' in the larger than the smaller sizes.

Jan 1, 1971

By George D. Brunton

The past and present argillaceous rock studies for the U.S. National Waste Terminal Storage Program consist of: (1) evaluation of the geological characteristics of several wide- spread argillaceous formations in the United States; (2) laboratory studies of the physical and chemical properties of selected argillaceous rock samples; and (3) two full-scale in situ surface heater experiments that simulate the emplacement of heat-generating radioactive waste in argillaceous rock.

Jan 1, 1981

By David J. Brown

Extensive deposits of bituminous, subbituminous, and lignite coals occur in the western United States (Figure 1). Over one trillion tons of identified resources have been located and inferred by geologists and more than 200 million tons of western coal are mined annually (1). In the future, production of western coals will increase significantly and approach national production levels of higher-rank eastern coals. Western coals will be utilized in new power plants as a replacement fuel for oil and gas and may be used in advanced technologies such as diesel engines or in direct-fired turbines. Since these applications require low-ash, low-sulfur coals, crushing to fine sizes and significant cleaning to remove minerals and sulfur will be required. Coal cleaning traditionally has been associated with reducing pyrite and other mineral matter from high-rank eastern coals. To date, insignificant quantities of western coals have been cleaned before utilization and limited data on their washability characteristics exist. Because of this lack of data, it is difficult to predict how these coals will react to standard washing techniques.

Jan 1, 1985

By Yi Luo, Jian Yang, YUJIA LIAN

Scale physical models, constructed according to the principle of similarity theory, are widely used to simulate the mining disturbances to surrounding strata and to evaluate the effectiveness of implemented ground-control techniques. This technique has also been used for studying mining-induced surface and subsurface subsidence. The movements of the observation points installed on the physical model at different mining stages are currently measured using a total station, which is time consuming and inaccurate, especially on small-scale models.

By A. H. Shapiro, W. –F. Leung

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micrometer-range particles that form pastelike, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake flow control structure that allows expressed liquid, from the cake in the dry beach region to be returned to the liquid pool while maintaining a high-solids throughput. To provide optimal performance with various operating parameters (i.e., feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids and slurry type), the cake flow control is adjustable. The second part of the beach is preferably at a zero angle. Tests showed that the new design allows increases in solids dryness and solids throughput. Key words: Dewatering, Centrifuge, Slurry, Fine particles, Beach decanter, Cake-flow control

Jan 1, 2003

By L. J. Habegger

This paper considers the potential water quality impacts of future energy scenarios which project an approximate doubling of coal utilization from 1975 to 1985. The major impacts estimated for coal extraction are related to effluents from unregulated activities (reclaimed areas prior to stable vegetation) and pollutants (e.g., metals and ammonia). Where applicable, the EPA effluent guidelines to be in effect by 1983 reduce the impact of individual sources to low levels. For example, total suspended solids and acidic discharges are to be regulated to levels generally below recommended water quality standards for receiving streams. However, implementation of these guidelines, particularly for coal extraction, has not been demonstrated on a wide scale. Water quality is not expected to be a major constraining factor for increasing capacity of coal fired utility and industrial boilers. Water quality control has not been demonstrated on a commercial scale for coal conversion to synfuels, but adequate control technologies appear to be feasible.

Jan 1, 1978