Search Documents

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

Introduction Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 12, 1986

By Joseph J. Zaluski, J. Steven Gardner, Marco M. Rajkovich

The telephone rings at 3:20 a.m. An exasperated voice on the other end says, “There has been a mine explosion at Mine No. 5 and we have not heard from three units of men.” Twenty-three minutes later, the phone rings again and another panicked voice says, “There is something wrong at the slurry impoundment, the pool level has just dropped five feet and we are trying to figure out what is wrong” Thirty minutes later, the mobile phone rings. An excited security guard says, “We have reports of thick black water running down the right fork and left fork of Straight Creek and both seem to be rising in the banks.” If this is not enough excitement, the mobile phone rings again. A stressed company official says, “I just heard a report that black slurry is running out of the portals of XYZ Co. No. 2 Mine, which is adjacent to our No. 5 Mine.” Is this all some kind of dream or nightmare? More importantly, though, if this happens, what do you do? Most people think: “It can’t happen to me.” But mine explosions do happen, slurry impoundments can rupture and creeks can flood with black water causing damage to others, including competitors. A mine’s response must be quick, cool-headed, calculated and effective. This article examines the issues, concerns and ramifications of this hypothetical disaster. The authors then present a systematic crisis-management response.

Jan 1, 2004

Narrow vein mining, with enough challenge and also where the cutting edge technology can be applied, is still a very important and exciting portion of the mining industry. Based on the deposit characteristics, the most flexible mining method, cut and fill, has been being tested mining this high grade Northern Nevada property, Hollister, since the year of 2008. In the last three years, 254,000 tons of ore were hauled out of the portal and 23,000 feet of development were excavated underground with the winning of several safety and environmental awards. Together with mine geology, the essential segments include mining cycle, ground control, ventilation, grade control and backfill method in cut and fill stopes were covered in this paper.

Jan 1, 2012

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By J. D. Lowell, L. Quevedo

I will talk today about a porphyry copper exploration program now underway in the Amazon jungle in the southeastern part of Ecuador near the border with Peru. The project is unusual for two reasons: first the deposits are of Jurassic age, 153 m.y.o., which is unusually old for porphyry copper deposits and they may be the most significant pre-Tertiary age porphyry deposits known. Second, the district was found only six years ago which makes this the most recent discovery of a totally new porphyry copper district. The new porphyry district, known as the Zamora River Copper Belt, or the Corriente Copper Belt, is a north trending area 50 km long by 10-15 km wide, which is nearly aligned with the axis of the Jurassic age Zamora batholith and with the course of the Zamora river. Gencor in 1994 initiated a regional grassroots gold exploration program based on reconnaissance geologic mapping and geochem sampling which did not find a gold mine, but which identified the San Carlos porphyry copper system in April, 1995. In a later reorganization between Gencore and Billiton the Ecuador project was transferred to Billiton and between the Gencore work and Billiton’s a total of 10 porphyry copper systems were found over the next four years. In the period of 1997 - 1999 Billiton drilled a total of 11,000 meters of wide spaced core holes in the San Carlos, Panantza and Kutukus prospects. In October 1999 Billiton concluded a farm-out, joint venture agreement with Corriente Resources and Lowell Mineral Exploration for additional exploration of the Zamora property. This is funded by Corriente and managed by Lowell Mineral Exploration and a total of 28,000 m of core drilling was completed through August 2001. An immediate result of the Corriente Lowell project was the discovery of potentially commercial ore reserves in two new deposits at Mirador and Warintza. Additional closer spaced drilling was done in the Panantza deposit and additional drilling is planned at San Carlos, in targets related to Warintza, and elsewhere.

Jan 1, 2002

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study has been conducted to control iron in copper electrolyte streams using Eichrom Industries’s new Monophosphonic /sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27 g/L of iron and can be readily regenerated. In addition, the new resin can be easily synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydro-metallurgical streams.

Jan 1, 2000

By Paul H. Johnson

Resource Engineering and Development, Inc. is desigining and building a portable 150 to 225 tpd, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, highgrade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on 18 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981

By H. Walqui, G. Rajala, G. Suardini

The Empire mine began operations on 1963. Low grade Magnetite ore is processed to produce iron pellets for blast furnace feed. Three expansions were added to the original plant and several equipment upgrades have been completed to improve the plant performance as the ore characteristics have been changing through the life of the mine. Size reduction is carried out by two grinding stages, the first one using autogenous grinding and the second one using pebble mills. Pebble crushing is also used to break the critical size fraction and increases primary grinding capacity. This paper describes changes in the configuration of the grinding circuits that have helped increase plant throughput and reduce power consumption by more efficiently utilizing assets available. Understanding the different components of the size reduction circuits and plant sections has allowed shifting part of the load from one section of the plant to another without affecting plant throughput.

Jan 1, 2007

By D. Tao

The reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In such a process quartz is often floated with ether amines (R?O(CH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of hematite does not work well if a certain amount of slime is present in ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the flotation efficiency of iron ore flotation by use of a new type of depressant for clay and iron minerals, i.e., GP clay binder. It is postulated that the GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It is further theorized that the clay binder helps depress hematite flotation due to its unique chelating ability to iron ion. The results from this study clearly show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing concentrate grade to 67.08% and iron recovery to 78.15% simultaneously. Key words: Clay Binder; Depressant; Iron Ore; Flotation.

Jan 1, 2009

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By Steve Klein

The Transbay Downtown Extension (DTX) in San Francisco involves the construction of a large-span tunnel with a width ranging from 43 to over 60 feet. The tunnel will be excavated using the New Austrian Tunneling Method (NATM), also known as the Sequential Excavation Method (SEM), in highly fractured and sheared rock. This paper discusses the FLAC (Fast Lagrangian Analysis of Continua) analyses that were completed for conceptual design of the tunnel support system and to develop surface settlement estimates for the evaluation of measures to protect existing buildings located above the tunnel from damage.

Jan 1, 2008

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By K. Boakye, T. Newman, P. Bláha, M. B. Toelle

"This paper presents a quarry optimization plan using a block model and an in-house development quarry scheduling and optimization software (QSO Expert) to help improve quarry operations at Crystal River. The Crystal River Quarry is an underwater quarrying operation that barges limestone via the Gulf of Mexico, as the main source of raw material to a cement plant in Theodore, Alabama. To improve the quarry operation, an evaluation was completed to optimize the quarry planning and extraction procedures of the quarry. In order to achieve this, additional exploration drilling campaign was implemented, a new block model was re-calculated and the latest version of QSO Expert software was used. The primary economic impact is a higher recovery of limestone reserves; sustainability of resources, corresponding longer quarry life. Secondarily as the limestone is mined underwater and stockpiled above water, drainage reduces moisture content achieving direct cost reduction on limestone shipping. In addition, a considerable reduction in operational cost was achieved due to a significant decrease in consumption of electrical energy, reduced dragline maintenance costs and reduced dragline movements within the operation. INTRODUCTION Holcim is a Swiss-based global building materials and aggregates company. Founded in 1912, the company expanded into France and then throughout Europe and Middle East during the 1920s. In 1922, Holderbank, as the company was then known, expanded beyond the Swiss borders into France. By the end of the decade Holderbank held stakes in Belgium, Germany, the Netherlands, and Egypt (Holcim History 1912-2012) Positions in Lebanon and South Africa soon followed.. Holder bank later expanded in North America in the 1950’s. In the late 1970s and early 1980s, Holderbank continued its expansion in Latin America, Asia and Spain for the first time. The company expanded into Eastern Europe and experienced a boom in Spanish construction preceding the 1992 Summer Olympics. By 1986, Holderbank was the world's largest cement manufacturer. In the 1990s, the company consolidated its European holdings as the American market drove growth. Expansion into Eastern Europe and Russia continued (Holcim History 1912-2012). In 2001, the company changed its name from ""Holderbank Financière Glaris"" to Holcim (short for Holderbank ciment) (Holcim History 1912-2012). Holcim expanded by purchasing Aggregate Industries entering into the United Kingdom for the first time. That year, the company also expanded into India by acquiring a stakes in The Associated Cement Companies (ACC) and Ambuja Cement Eastern. In 2008, Holcim became the largest shareholder of China's Huaxin Cement with a 40% stake. In 2009, they acquired Cemex Australia. In 2014, Holcim and Lafarge announced they had agreed to terms on a ""merger of equals"" valued at nearly $50 billion in 2015. The new company LafargeHolcim based in Switzerland has a manufacturing capacity of 427 metric million tons a year."

Jan 1, 2017

By Chester M. F. Peters

The opportunity to make a close study of the available geologic data existing along the line of the California Aqueduct crossing of the Garlock fault in the Tehachapi Mountains was brought about first by my involvement in the prebid examinations, and later with contractors' claim cases. The California Aqueduct crosses through the western end of the Tehachapi Mountains and cuts across the Garlock fault zone at a location about 9 miles east from its junction with the San Andreas fault zone. This is about 65 miles northwest of Los Angeles and 38 miles southeast of Bakersfield (Fig. 1) (1). This map was published after the tunnels were started and shows the corrected geology. At the crossing the fault has north and south branches which extend northeastward for about 22 miles before converging. In the vicinity immediately east of the tunnel line the north branch of the fault starts to converge toward the west. After crossing the line it passes under the upper plate of the apparent easterly extension of the Pastoria thrust fault, so the actual junction with the south branch is obscured. The aqueduct design called for the expected active slip zone of the north Garlock fault branch to be crossed by the 2,800 foot long Pastoria siphon, which connects with the north portal of Tehachapi Tunnel No. 3. The tunnel would extend through the western end of Genghus Ridge which lies between the north branch and the main south Garlock fault zone in Beartrap Canyon. Here again the

Jan 1, 1997

By Franz Walchshofer, Mark Kuchta, Nobuharu Isago, Ugur Ozbay, Wolfgang Dolsak

A series of in situ pull test were performed on a new design friction stabilizer bolt with the objective of determining its performance characteristics. The bolt is installed while drilling, thus improving safety and significantly reducing the installation time. An optional expansion element can be inserted into the bolt to provide an end-anchorage, which further increases the bolt’s capacity. In situ tests show that the pull capacity of the 2 m long new design bolt is about 15 tons. When installed with an expansion element, the pull capacity of these bolts becomes as high as 30 tons.

Jan 1, 2005

By E. Stolarski

The circulating fluid bed (CFB) technology can proudly point to its history of more than a quarter of a century of commercial operations. Over 80 CFB units operate in aluminum calcining, coal combustion and gold roasting. This paper describes the invention of the circulating fluid bed and chronicles its development and evolution from calcining through coal combustion to gold roasting. It presents performance data of Lurgi's CFB units in operation and highlights the six gold roasting plants currently operating throughout the world.

Jan 1, 1998

By M. S. Riyazulla

A model of a new laboratory magnetic separator has been conceived to cater the needs of process engineers and mineralogists world over engaged in mineral characterization and beneficiation. It would be essentially a laboratory instrument for the separation and concentration of various ferro and non-magnetic minerals. Based on the basic concept of Frantz Isodynamic Magnetic Separator, the new separator conceived would not only speed up the work of a process mineralogist and save the energy, but it would effectively separate and sequentially produce about fourteen fractions at a time. In the present paper, the probable operational procedures and the design have been discussed in detail for the various mining companies to assess its economic feasibility. If it could be fabricated, it would have a worldwide market The concept has been patented in author?s name in India.

Jan 1, 2009

By Rodney K. Morrison

MARTA, The Metropolitan Atlanta Rapid Transit Authority, is building a 53 mile heavy rail transit system to serve the City of Atlanta. Phase A of the Rail System, consisting of approximately 14 miles of at-grade, aerial and subway construction is underway. Metropolitan Atlanta lies in the Piedmont Geologic province of Georgia and is underlain by rocks of essentially granitic and gneissic nature. The soils encountered are primarily silty sands which are in-place weathering products of the parent rock and exhibit their relic structure. In general, these materials have presented no unique construction problems other than those created-by proximity of manmade structures, local availability of ground water, and top of rock elevation. The subway sections of primary interest in this paper consist of hardrock and soft ground tunnels and extensive cut-and-cover sections. The cut-and-cover construction includes excavations as deep as 80 feet. Temporary support systems in these deep excavations consist of soldier pile-timber-lagging or soldier pile-tremie concrete (SPTC) walls with internal bracing or tiebacks. In shallow cut-and-cover sections, where right-of-way economics permitted, slopes were laid back partially or fully to reduce or eliminate the need for bracing systems. Dewatering systems were required in most open cut excavations. Due to the close proximity of utilities and existing structures to the MARTA

Jan 1, 1979