Search Documents

By Robert H. Merrill

INTRODUCTION In most cases, the design of an underground mine is based upon the premise that the ground either will cave or will be stable. This chapter concerns the design of a mine in ground that will cave readily or with some as¬sistance, such as by long-hole drilling and blasting. Some of the more widely used caving systems of mining are panel caving, block caving, sublevel caving, and large pillar recovery. Some of the less widely used systems are glory-hole, top slicing, and induction caving. Al¬though the common practice of pillar robbing is not usually considered to be a caving system, this subject will be treated as a part of this chapter. BASICS OF CAVING Caving systems are most successful in ground that will cave in sizes that will flow through openings and grizzlies, and will easily load in cars or on belts for haul¬age. The ground most likely to cave well is highly frac¬tured and contains breaks, flaws, or other discontinui¬ties that form planes of weakness. Also, caving action can be greatly enhanced if the host rock itself is low in compressive, shear, and tensile strength. Ideally, a cav¬ing system of mining is best employed when the criteria for caving is a feature of the ore body and the develop¬ment drifts, haulageways, and drawpoints can be mined in a highly competent rock beneath the mineralized zone. However, the development is often in the same, or similar, fractured rock and the openings require sub¬stantial artificial support to assure stability. Several clues can be assembled to identify potential caving ground; however, for borderline cases, no sure method has been devised to date. The diamond-drill cores taken for exploration can provide an excellent clue provided drilling is performed carefully by experienced drillers. For example, if the ground is cored in such a manner that the breaks in the core are caused more by failure of the rock than by whipping core barrels, plugged drill bits, or other drilling causes, and the intact core lengths are consistently long [say, 0.6 to 3 m (2 to 10 ft) of unbroken core], there is little reason to believe the ground will cave without considerable as¬sistance. This is especially true for rocks with compres¬sive strengths above 34.5 MPa (5000 psi) and tensile strengths above 2.1 MPa (300 psi). On the other hand, if core recovery is low (below 80%) and the recovered ore is broken in small pieces and the breaks are along obvious weaknesses in the rock, the chances are excel¬lent that the ground will cave. This is true even when the rock between the defects has high compressive and tensile strength. Another clue has already been mentioned, that is, the measurement of the physical properties of the rock and the natural planes of weakness or defects in the rock. The planes of weakness in the rock can often be detected from outcrops, cores, or other exposures of the rock under consideration. Some rock types are known to be strong and will sustain large, unsupported open¬ings and would be difficult to cave intentionally. Yet the same rock type can also contain unbonded or weak planes of weakness or fractures, and in these locations the rock would undoubtedly cave with little assistance. Therefore, although the inherent strength of the rock is a factor in caving, the natural defects in the rock are more often the deciding factor. DESIGN CONCEPTS For the most part, the design of openings for caving ground is a problem of the interaction of openings over a relatively large area of the mine. To illustrate, Fig. 1 is a simplified section of a series of openings along the grizzly level or draw level of a block caving or panel caving development, and above this opening is a simpli¬fied section of a room-and-pillar arrangement on the undercut level. At this stage of the development, the stresses around the openings on the grizzly level are only moderately influenced by the openings on the undercut level and vice versa. Therefore, the stresses around the openings are approximated by the stresses around single or multiple openings in rock, the values of which are de¬scribed in the literature (Obert, Duvall, and Merrill, 1960; Obert and Duvall, 1967). Once the pillars on the undercut level are blasted (Fig. 2), the situation changes abruptly. The undercut opening (prior to caving) now can be approximated as an ovaloidal opening above the grizzly drifts and this opening tends to shield the vertical stress field. As the caved stage is drawn the stope approximates a much larger rectangular or square opening filled with rock, and if the rock is not sustaining a major portion of the stress field, this opening can be considered (for en¬gineering purposes) to be empty and the stresses that interact between the larger and the smaller openings take on a totally new perspective (see Fig. 3). Next, let the material cave to the surface, and let the caving ma¬terial sustain some stress, but much less than if the ma¬terial were intact. This condition is similar to a soft inclusion in a rigid body and has been treated in the literature (for example, Donnell, 1941). At this point in time, the grizzly drifts are subjected to the stress con-

Jan 1, 1982

By Harry M. Conger

Good afternoon, fellow members of the international mining community. I appreciate the opportunity to participate in this special three-day, international gathering, and to join with you in honoring one of my very good friends, Doug Fuerstenau. It couldn't be more fitting to have this kind of event to mark Doug's 60th birthday. You know, in addition to his faculty position at the University of California in Berkeley, Doug is a member of the Board of Directors of our Homestake Mining Company. So it is a double pleasure for me to help pay tribute to one of the outstanding academicians of the mining industry as well as a man with whom I work closely in running Homestake. I have been asked to talk about "The Future of Precious Metals," but I will concentrate my remarks on gold. Since the theme of this Symposium is "Challenges in Mineral Processing," what I'm going to talk about is a challenge that relates especially to a major problem faced by those of us who process ores to recover gold. I noted that in the Scope of this Symposium, it stated: "the mineral industry is currently facing many challenges to improve the economics, operating efficiencies and environmental concerns of the mineral processing system." I couldn't agree more with that statement. I think that a need exists for us to address this situation as it involves gold. And who better to consider this than the worldwide leaders of mineral processing research here assembled. I start with the premise that we need a new method for cyanide use or a chemical to replace sodium cyanide entirely. In the case of using cyanide differently, I see a continuing difficulty in getting general public acceptance regardless of how

Jan 1, 1989

By Guocheng Pan

This paper presents-:a new multivariate mineral resource estimation model, referred to as the Related. Information (RI). Instead of relating a mineral resource descriptor directly to a set of geological variables, the RI model relates the mineral resource descriptor to a synthesized information measure RI, which is created from a set of geological variables. All of the variables are transformed into binary characteristics. This model comprises two stages of estimation: estimation of a synthesized information measure and estimation of mineral resources. The information carried by a variable is classified into three types: mineralized-barren information, mineral resource variation information, and variable-controlling information. The synthesized information measure is defined as the product of the three types of information and the responses of binary geologic characteristics. The RI model is demonstrated on the pegmatitic Nb+Ta deposits in China.

Jan 1, 1992

By J. P. Ferro, W. H. Stewart

Wet ground and dry muscovite mica continued to be the most commercially significant types of mica in the US. Canada's phlogopite mica and some US deposits of sericite mica have also contributed to the overall application of mica in a variety of industries. Mica's major end uses are paint, rubber, and construction material. Its value was about $30 million last year. The southern Appalachian Mountains weathered granitic bodies and pegmatites continued to be the primary US muscovite mica source. North Carolina production of mica as a coproduct of feldspar, kaolin, and lithium processing accounted for more than 60% of the total output. New Mexico, South Carolina, South Dakota, Georgia, and Connecticut accounted for the rest. Flake mica was also produced from mica schists in North Carolina and South Dakota. It is also being investigated in Ontario, Canada. Wet ground mica Wet ground mica was produced by four companies: KMG Minerals, Franklin Mineral Products, J.M. Huber Corp., and Concord Mica. KMG and Franklin Mineral Products accounted for more than 80% of the production. Wet ground mica is a highly delaminated platey powder used to reinforce solvent and aqueous system paints for increased weatherability, durability, and greater resistance to moisture and corrosive atmospheres. In plastics, it is an excellent filler and reinforcing agent, providing better dielectric properties, heat resistance, and added tensile and flexural strength. In the rubber industry, wet ground mica is used as a mold lubricant to manufacture molded rubber products, such as tires. It also acts as an inert filler that reduces gas permeability. Miscellaneous uses include additives to caulking compounds, foundry applications, lubricants, greases, silicone release agents, and dry powder fire extinguishers. Wet ground mica prices range from $353 to $496/t ($320 to $450 per st) fob plant. Specialty products may be higher, depending on customer requirements. Dry ground muscovite mica Dry ground mica was produced by nine companies: KMG Minerals, Unimin, US Gypsum, Mineral Industrial Commodities of America, Spartan Minerals Corp., Asheville Mica Corp., Deneen Mica Co., Pacer Corp., and J.M. Huber Corp. Dry ground mica's primary market is wallboard joint compound. Here, it is a functional extender that improves the physical properties and finishing characteristics of the mud. It is also used in various grades as a filler in asphalt products, enamels, mastics, cements, plastics, adhesives, texture paints, and plaster. Dry ground mica became popular as an additive in oil well drilling fluids, where the mica flakes platey nature helps seal the well bore, preventing circulating fluid loss. But oil's dramatic price drop and consequent curtailing of well drilling brought this once booming market to a virtual halt. Forecasters predict that this business will gradually pick up during the next few years and most current dry ground mica producers will again produce the oil well drilling material. Dry ground mica prices range from $110 to $420/t ($100 to $380 per st) fob plant. High quality sericite mica, sometimes referred to as an altered muscovite, was mainly produced by two US companies. Mineral Industrial Commodities of America and Mineral Mining Corp. have equivalent capacities of about 27 kt/a (30,000 stpy). The majority of the material produced was consumed by the joint compound industry. Minor uses are in paint and oil well drilling. The lack of ground sericite penetration into the traditional ground muscovite markets is attributed to high silica content, typically in excess of 20%, and a bulk density. Prices range from $88 to $187/t ($80 to $170 per st) fob plant. Phlogopite mica is a dark colored, magnesium bearing mica rarely found in the US. Suzorite Mica Corp., a division of Lacana Petroleum, mines a deposit in Quebec that is 80% to 90% phlogopite. The dark color has prevented the material's entry into the traditional paint markets. But the physical properties and high purity make it useful as a low-cost reinforcing filler in many plastics and several asphalt applications. Phlogopite mica is ground to several grades and may be treated with various surface coatings for use in plastics or coated with nickel for EMI/RFI shielding applications. Prices for phlogopite products range from $144 to $580/t ($104 to $580 per st) fob plant. As in recent years, production of domestic muscovite sheet - block, film, and splittings - remained insignificant. These resources are limited and uneconomic due to the high cost of hand labor required to process sheet mica in the US. Imports from India and Brazil were the primary sources of the estimated 1 kt (2.4 million lbs) valued at $2.5 million consumed by US electronic and electrical equipment manufacturers in 1986. Reserves As a feldspar, kaolin, and lithium industry coproduct, flake mica will continue to provide a large percentage of mica re- This summary of 1986 mica activity was received too late to be used in the June issue.

Jan 7, 1987

The absence of coal face particle management practices heavily penalizes coal transportation from initial loading to final consumption. Penalties include dust problems, significantly reduced mine loading cycle productivity, mine belt spillage, excessively high coal preparation costs and chute and dangerous pulverizer blockages at the final point of utilization. The common environmental and economic enemy is fines. Everyone knows that fines cause safety and environmental dust problems, but few understand that fines also swell broken coal to a point where 5 to 15 percent more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long established and frequently misleading basis of tonnage. After all, it is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain non-frothing chemicals added to mine face spray water and/or by employing improved mine face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed.

Jan 1, 1994

By M. Shriwas, F. Calizaya

"Controlled recirculation may be considered as a beneficial means in mines of cold climate, where heating of air is required, and in deep or extensive mines, where cooling of air is required. Controlled recirculation can be designed by proper sizing of the booster fans with respect to main fan. Intuitively, it seems that the buildup of methane at the face will cease when a steady state condition is attained, and also that, at that same time, the maximum concentration at the face will remain same as in the return air. This supposition is proved by mathematical analysis that considers uniform mixing of methane in air in successive cycles of recirculation. This study includes two scenarios to show the effect of controlled recirculation on methane concentration in a sample network. Firstly, when recirculation crosscut exists near the working face; secondly, when recirculation crosscut exists away from the working face. The later scenario shows lesser buildup of methane concentration than the former one. INTRODUCTION The controlled recirculation is designed purposefully to allow a partial fraction of used air that increases the air velocity due to increased quantity of air and consequently allows effective dilution of contaminants to improve local ventilation condition at the working face. It can be designed by proper sizing of booster fan with respect to main fan in a ventilation network. Controlled recirculation may be categorized as crosscut, in-line or combined system based upon the configuration of the booster fan locations in a district ventilation network. Research on controlled recirculation has shown numerous benefits of controlled recirculation especially in deep or extensive underground mines, where further heating or cooling is required (Calizaya 1990; McPherson 1993 and Jones, 1987). However, fear of buildup of concentration has misled the mining communities to view the controlled recirculation as a hazard and deprived the mining industry to derive benefits from recirculation. Intuitively, it seems that the buildup of methane at the face will cease when a steady state condition is attained, and also that, at that same time, the maximum concentration at the face will remain same as in the return air. This supposition is proved by mathematical analysis that considers uniform mixing of methane in air in successive cycles of recirculation. This study includes two scenarios to show the effect of controlled recirculation on methane concentration in a sample network. Firstly, when recirculation crosscut exists near the working face; secondly, when recirculation crosscut exists away from the working face. The later scenario result shows the less buildup of methane concentration than former scenario result."

Jan 1, 2016

By Dong-mei Zhang, Feng Zhang, Hong-Wei Huang, Qiang Huang, Bin Ye

"1. INTRODUCTION Nowadays, many cities around the world have constructed metro tunnels to alleviate transportation pressure from rapid urbanization. In soft soil areas, metro tunnels are usually constructed by shield-tunneling method due to its high efficiency and little disturbance to environment. However, the tunnels may show significant post-construction settlement after several years of operation. Take Shanghai Metro line 2 for example, the maximum longitudinal settlement reached 160mm after ten years of operation, shown in Figure 1. When analyzing varying factors that contribute to the long-term settlement of tunnels, the effect of cyclic loading from train vibration is rarely taken into consideration for most researches only focus on the influence of leakage problems in the tunnel while neglecting train vibration induced leakage and resulting settlement. It’s true that metro tunnels from shield-tunneling method are prone to have leakage problems due to the special structural configuration. Furthermore, trains move hundreds of times inside the tunnel every day, which inevitably will cause accumulation and dissipation of excess pore pressure. When the excess pore pressure dissipates, tunnel settlement induced by train vibration occurs(Deng F H, 2007). Although researchers (Zheng et al., 2005; Wongsaroj et al., 2007; Mair, 2008; Shin et al., 2012; Zhang et al., 2012, 2015) conducted extensive numerical analysis on the relationship between tunnel settlement and relative permeability of tunnel to surrounding soil by treating tunnels as permeable media, their attention was only paid to the tunnel settlement from reduction of hydrostatic pressure in the ground, rather than from the dissipation of excess pore pressure generated by train vibration. Therefore, the influence of train vibration on the long-term settlements of metro tunnels is still not clear."

Jan 1, 2016

By F. Soumis

This paper describes an integrated procedure for the very short term production planning of an open pit and the execution of this plan: the truck dispatching. Integration of plan and dispatch means that the plan is realistic so that its objectives can be realized by the dispatch. This realism is obtained by supplying the plan optimization, which involves mixed integer programming, linear programming and non-linear programming, with experimental O.R. models of waiting and blending. The arrangement of these models in the computer programm has made it possible to obtain very short computing time for the planning in spite of the width of the optimisation. The dispatching of a truck is made by solving a classical assignment problem for each dispatch over a horizon of the expected*next 10-15 trucks to request dispatches. This deep-reaching dispatch procedure uses the continuously arriving information about trucks' positions and shovels situations and models by probability functions the expected waiting time of shovels and trucks. In this manner trucks and shovels are synchronized and last moments' opportunities for productivity gains can be obtained. The dispatch procedure takes .5 second on PDP11. This integrated planning and dispatch procedure gives high productivity while ensuring good blending. Results from the Mount Wright mine of the Quebec-Cartier Mining Co., where the integrated procedure has been installed on the existing computer equipment PDP11, are included.

Jan 1, 1989

By T. Resende, J. Sismour

"Signs in underground mines are subject to variable airflow, which carries dust and moisture. Dust buildup reduces their visibility, hampering production efficiency and safety. Underground workers commonly must stop to clean signs in order to gauge their location, or find critical supplies or services. There are currently a variety of coating products, including dust and water repellants, available on the market that have the potential to reduce dust accumulation on sign surfaces. This paper describes a preliminary study to determine their effectiveness. The study involved a practical testing protocol using a trickle rock duster and samples cut from a clean, used road sign. Product effectiveness, under both dry and wet conditions, was evaluated based on photographic evidence by comparing changes in sign luminosity after a period of rock dust application. By analyzing the frequency of different pixel luminosities on the dust-covered samples, both uniformity of dust coverage and the total amount of accumulation was assessed. Results indicate that at least one product may reduce the amount of dust buildup on sign surfaces and increase visibility. INTRODUCTION In all underground mines, visibility of signage is critical. Signs inform miners of their location, direction toward escape routes, and location of supplies. Over time, sign surfaces can collect dust and can eventually become unreadable. The rate of dust accumulation on surfaces is often particularly high in coal mines, where both mining (e.g., cutting and drilling) and rock dusting activities can contribute significant amounts of dust to the airways. Several factors may contribute to dust buildup on sign surfaces. First, basic principles of fluid and particle flow are at play. When a fluid travels past a stationary surface, the velocity of the fluid at the surface boundary is zero. If a very small dust particle moving with air collides with a surface, it does not immediately fall off since the air velocity is zero at the sign surface. (This is the same reason that dust can collect on a rotating ceiling fan.) Further, once the collision occurs, other mechanisms may help keep the particle there – including friction that resists particle falling due to gravity, and adhesive forces due to humidity and/or static charges the particle and others already on the surface. Currently, the most common way to deal with reduced sign visibility due to dust buildup is for mine personnel (e.g., a compliance foreman, supply worker) to periodically clean sign surfaces – usually just by wiping them with a cloth. As a regular activity, this solution is inefficient; in cases of emergencies, it can also pose unnecessary risks. Application of an off-the-shelf coating to sign surfaces may represent a simple yet effective way to reduce the rate of dust accumulation. There are currently a variety of products on the market that may be suitable for this purpose, including dust and water repellants."

Jan 1, 2017

By R. S. Shepard

A quick glance at a-portion of the title of this discussion -'Rolling With The Punch" may immediately lead you to assume that I am about to expound on the so-called manly art of self-defense. So that you will not have been misled entirely we will devote our considerations to a far more important art and if I may, I should like to begin by quoting Vincent Van Gogh. According to a literal translation the artist in describing one of his famous paintings said "these peasants are eating their potatoes with those very hands that dug them from the earth' and put them in the dish". Vincent Van Gogh may not have realized at that time, that he could likewise have been describing what is probably one of the oldest of all arts - the art of Material Handling - an art that man with the aid of science has tried to improve since the beginning of time.

Jan 1, 1963

By Hans-Werner Tonscheidt

Introduction The endeavours to mechanise the shaft sinking operations have led to the development of shaft boring using a V-Mole. The method implies competent ground and a pilot hole of sufficient verticality. This connects the top and the bottom of the shaft and serves for air ventilation and the transport of mullock. The shaft boring machine - nick name V-Mole - with a general pattern similar to a tunnel-borer reames the pilot hole to the designed diameter of the shaft. (Figure 1) The excavating of the rock, the removal of the mullock from the face and the lining of the shaft wall are done simultaneously. If they can be done also continuously this than creates a high potential of productivity. The verticality of the shaft can be garanteed due to the laser beam guided steering system. The diameter of the shaft is variable in steps of 0.5 m between 6.0 and 10 m in accordance with the need. It decides the capacity of the V-Mole to be applied. The depth of the shaft does not depend on the machine. It is practically unlimited as long as a suitable pilot hole is available. Up to 1988 almost 12.656 m of shaft have been drilled on 40 individual projects in Germany and the U.S.A. using a V-Mole. The rocks penetrated were Carboniferous sediments consisting of Sandstones, Shales, Conglomerates and Coal seams. The average uniaxial compressive strength was in the range of 300 - 700 Mpa with a maximum of 1700 Mpa in some singular sandstones.

Jan 1, 1991

By John J. Mulligan

Coal is found in every major geographic region throughout Alaska and in two offshore areas. Since about 1852 over 100 small mines have opened and closed. Last years production was almost entirely from one mine in central Alaska. Clearly the utilization of Alaska's abundant coal resources presents political, economic and technical problems that are far from solution. Location and Physical Features Figure one illustrates the geographical and geological similarity between Alaska and western United States. The Arctic region of Alaska generally resembles Wyoming and the Dakotas. The Brooks Range is an extension of the Rocky Mountains. The Central region of Alaska between the Brooks Range and the Alaska Range bears a general resemblance to the basin and range country of western United States. The Southcentral and Southeastern regions has a similar resemblance to the Sierra Nevadas and the west coast of the United States.

Jan 1, 1982

By Gunter Zimmermeyer, Hartmut Eicker

Radon in the Environment Radon, as a natural nobel gas, can be detected nearly everywhere in the environment as a decay product of ubiquitous uranium. As it is emanated from soil and rocks measurable concentrations have been found at the surface of soils and in even higher concentrations in enclosed spaces like, for example, mines and buildings. While above soil surface activities caused by radon have been found in an order of magnitude of up to 1 pCi/l (Weigel, F. 1978), concentrations in enclosed spaces and mines are higher because of the lack of atmospheric circulation. Beside air circulation the relevant figure depends on the Ra226-concentration in the surrounding rocks or building material, as well as on emanation coefficient and the diffusion coefficient. While representative Rn222concentrations in well ventilated buildings are reported to be in an order of magnitude of 1 pCi/l maximum values up to one order of magnitude higher have been found in badly ventilated brick buildings (Ettenhuber, E., Lehmann, R., Clajus, P., 1978) (Aitken, J.H., et al., 1977). Just now it was stated that the reduced air circulation due to German legal regulations on energy conservation will increase radon exposure of the public considerably (Jacobi, W., 1979). Radon in Mines Radon exposure of workers is, of course, a matter of concern in uranium ore mines where relatively high concentrations of the uranium to be mined are present. Measures to protect workers' health have been implemented, based on experience on dose-effect relationship. They serve to meet exposure standards by limiting inhalation of radioactive particles, in reducing radon concentrations or in limiting working hours. Both improved measuring devices and capacity as well as the lower discrimination threshold enable to measure radon concentrations in other mines, e.g. in coal mines. It is known that radioactivity in coal is small compared with that in other minerals and even soil, rocks. Nevertheless, radioactive elements were identified in coal and so the question was whether the concentrations of radon in coal mines might be a subject of concern. The problems encountered when measuring radon in coal mines are described below, as the measuring device has to be flame proofed which is an important additional requirement. Measured radon concentrations in British coal mines have already been published (Duggan, M.J., Howell, D.M., Soilleux, P.J., 1968 (Dungey, C.J., Hore, J., Walter, M.D., 1978). The authors found concentrations of up to 14 pCi/l in Cornish mines. In most cases the values were in the order of 2 pCi/l. These results were consistent with measurements reported from U.S.-coal mines (Lucas, H.F., Gabrush, A.F., 1966). Such concentrations of radon were not considered to represent a hazard for British miners (Ogden, T.L., 1974). In Germany, too, first measurements have been carried out in five coal mines in the Saarland in the 60's. Air samples were taken at different places in the coal mines, dried, fed to an ionisation cell and measured by a device including reference cells. Samples taken at ventilated places showed radon concentrations consistent with the lower British results. They all kept within the standards of the first German regulation on protection against radiation. Measuring the radon daughters was renounced because of the relatively low radon concentrations and the requirements for flame proofness in coal mines. Moreover, it can be ascertained that because of the effective ventilation the disequilibrium factor between the decay products and the radon concentration remains far below the value of one (Muth, H., 1978) (Keller, G.). In 1979 the committee on mine safety and health protection in coal and other mines of the EEC proposed to have measured and evaluated radon concentrations in European coal mines to find out whether they complied with international standards. Great Britain and Germany agreed to this proposal and by commissioning such measurements to scientific institutes complied with the request to harmonize the methods used. In the Federal Republic of Germany, e.g. Westfälische Berggewerkschaftskasse (WBK) and Staatliches Materialprüfungsamt; Dortmund (MPA) were requested to carry out the measurements in coal mines of the Ruhr coalfield whereas Saarberg Interplan was responsible for the Saar coalfield. The WBK measurements are reported in later paragraphs.

Jan 1, 1981

By Lynn B. Hales

Everywhere you turn today there are articles on artificial intelligence and the rapid emergence of expert systems. Expert systems form a class of software that has developed as a result of the large research effort to develop computers and software that think intelligently. By definition, an expert system is a computer program that contains the knowledge component of an expert skill, can offer intelligent advice and justify its line of reasoning. Expert systems can advise people on what actions to take and when, assist in the diagnosis of the physical condition of a human patient or piece of equipment, or even take actions without human guidance, as in process control applications. Expert systems can also explain the line of reasoning behind a particular piece of advice or query for information from the user. Expert systems can be used as advisors to newcomers in any field in which mastery is attained by many years of experience. They often can provide expertise more uniformly and rapidly than human experts. Expert systems can also provide a means of documenting expert knowledge and procedures and provide a common repository for a changing knowledge base. The expert system can represent the best expertise available, thought out in the absence of pressure situations. Each of these attributes or characteristics should be helpful in improving typical concentrator control systems.

Jan 1, 1987

By Richard F. McFarlin

INTRODUCTION Phosphate, one of the three major elements essential for all living plants and animals, has been mined in Florida for over a hundred years. Comprising roughly 80% of the U.S. total and 25% of the world's supply, the bulk of the 35 to 40 million annual ton output is converted to chemical fertilizers. With the exception of one mine in north Florida near the Georgia state line, today's mining activities are centered in the middle of the peninsula just east/southeast of Tampa in Polk, Hillsborough and Hardee counties. These "bone valley" deposits extend into Manatee and DeSoto counties, but there is little active mining there as yet. Because strip mining is, perhaps, the ultimate environmental insult and because Florida has a proactive environmental community, it is not surprising that the mining of phosphate rock has become increasingly controversial. This paper describes how phosphate rock is currently mined, the environmental problems presented by mining and processing the rock, and some mitigating technologies being employed to answer such problems. THE PHOSPHATE DEPOSIT AND ITS EXTRACTION Florida's phosphate deposits containing the calcium phosphate mineral, carbonate-fluorapatite, are between ten and fifteen million years old. The typical "bone valley" matrix is 15 feet thick and lies under 20 to 30 feet of overburden.(Fig. 1) Both the sandy overburden and matrix are unconsolidated and can be removed with standard 45 to 65 cubic yard, walking electric draglines. After removing the overburden, which is windrowed nearby, the dragline operator casts the matrix into a "slurry" pit where it is broken up by high pressure water monitors. Pit pumps (with boosters where necessary) transport the matrix slurry through 16 to 20 inch pipelines to a washer where the three components of the matrix (sand, clay and apatite) are separated. The phosphates contained in central Florida matrix are approximately half pebble/half flotation feed, through the pebble ratio decreases as the industry mines southward. Again, the matrix is roughly equally divided among sand, clays and apatite. The phosphatic clays, 75% of which are less than one micron in size, leave the washer as a 3 to 5% colloidal suspension. The impoundment of these waste clays is one of the environmental challenges to be discussed later. The sand (silica) is separated from the similarly sized phosphate particles by a double float process (fatty acid followed by a reverse mine or cleaner float), and the sand tailings are then pumped to disposal or reclamation sites. The apatite flotation product is combined with the screened phosphate pebbles and stacked to dewater before shipping.

Jan 1, 1992

By Gary L. Simmons

Many large (refractory) sulfide gold resources exist in Nevada and other parts of the world that are not amenable to conventional flotation concentration using air as the flotation gas medium. Over the past five years Santa Fe Pacific Gold Corporation (SFPG) has investigated flotation process options to economically treat refractory ores and resources of this type at its Lone Tree and Twin Creeks mines. Conventional flotation technology applied to the original high-grade gold resources at Lone Tree and Twin Creeks was initially unsuccessful. Review and analysis of auriferous (gold-bearing) iron sulfide mineralogical characteristics and flotation ..:hemistry provided a fundamental understanding that led to the development of a new flotation process that SFPG refers to as N2 TEC. This paper discusses the development of this technology and compares N TEC results with conventional flotation practice.

Jan 1, 1997

By Richard L. Wedertz

Although the physical appearance of excavating equipment doesn't seem to have radically changed over the past decade, important changes within the products and an innovative attitude on the part of the engineer in his design approach is becoming increasingly evident. The new philosophy is to go beyond simple refinements of existing designs that simply produce a machine which further reduces overall cost per ton or per cubic yard of material moved and to do it more efficiently than ever before. Standard ideas and preconceived notions have been discarded and have given way to providing a design and a machine that is best suited to get the job done. Understanding that the application will not always fit the machine, but, in most cases, the machine should fit or suit the application is a foremost consideration in the engineers' design criteria.

Jan 1, 1973

By V. B. Achanti

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the: fragmentation process were found to be: bit spacing, bit geometry, depth of cut, and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Three bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 90°. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Respirable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Jan 1, 1997

By Michael J. Pratko

The bulk handling industries have long been plagued with problems in their attempt to obtain one of their major goals - the maximum efficiency for which a bulk handling flow system was designed. Mentor Dynamics Ltd. is an international firm with offices in Canada, Japan, and the United States. Mentor Dynamics Ltd. is in the business of solving the "why not" of a system and engineers the solution for the problem. Studies of the varied difficulties encountered with bulk flow systems indicate that 90% of all flow problems fall into one or more of the following categories: abrasion, impact, sticking, and/or inadequate design. These problems can occur with a myriad of bulk solids: coal, gypsum, aragonite, phosphate, fly ash, ore. Solutions to the problems are as varied as the problems. The proper lining material, ceramic, urethane, rubber, and/ or ultra high molecular weight polyethylene, must be coupled with the correct fastening system, annular ring and 'F' cap, weld washer, button head fastener, weld studs and/or nuts and bolts.

Jan 1, 1982

"Foreword by Lisa SchlinkSuperintendent, operations, Freeport-McMoRan Inc.,Green Valley, AZ, USAThe sixth annual Student Poster Contest hosted by the Mineral & Metallurgical Processing Division of the Society for Mining, Metallurgy & Exploration was held during the 2015 SME Annual Conference and Expo in Denver, CO. The contest had another record-breaking attendance of 31 entries: 27 graduate and four undergraduate. The universities represented were: Colorado School of Mines, South Dakota School of Mines and Technology, University of Kentucky, University of Utah, Southern Illinois University Carbondale, University of Wyoming and West Virginia University.The competition began with an extended abstract review by a panel of judges selected from MPD members. At the SME Annual Conference, all students displayed their posters, highlighting their research. The students with the top abstracts from the graduate and undergraduate divisions presented their research at the MPD Student Poster Session Wednesday morning. The panel of judges then provided tallied scores for the abstract, poster and presentation to determine the winners of the 2015 Student Poster Contest. The first- and second-place winners of both the graduate and undergraduate divisions received $1,000 and $500 scholarships, respectively. The third through seventh places received $200 each, and all other entrants received $100 each and were invited to join the MPD Luncheon.In the undergraduate division, Annette Hein of the University of Wyoming received first place for her research on “Solvent Extraction of Europium from a Nitric Acid Solution.” Second place went to Jennifer Galvin of South Dakota School of Mines and Technology for her research titled “Solvent Extraction of Neodymium Using PC88A.”In the graduate division, Caelen Anderson of the Colorado School of Mines received first place for his research titled “Fundamentals of Rare-earth Flotation Surface Chemistry: Hydroxamate Adsorption on Bastnasite”. This is Caelen’s fourth year placing in the top finisher. Second place in the graduate division went to Seyed Hassan Amini of West Virginia University for his research on “Ultra Clean Coal Production for the Solar-cell Industry.”The 2015 Student Poster Contest was chaired by Lisa Schlink (Freeport- McMoRan Inc.) and Emily Sarver (Virginia Polytechnic Institute and State University). The panel of judges included Aaron Noble (West Virginia University), Nick Gow (FLSmidth), Ren Bryce (Freeport-McMoRan Inc.), David Perkins (Derrick Corp.), Jim Metsa (Weir Minerals) and Scott Shuey (Newmont).A special thank you is extended to the sponsors of the MPD Student Poster Contest, to all the students who participated and to the panel of judges. Watch for more information on the 2016 MPD Student Poster Contest to be published later this year on http://www.smenet.org/mpd/ and in the November issue of Minerals & Metallurgical Processing."

Jan 1, 2015