Search Documents

By S. J. Lötter

Analysis of the major and minor components of raw zircon as well as plasma-dissociated zircon was undertaken using inductively coupled plasma optical emission spectroscopy (ICP-OES). Microwave-assisted acid extraction as well as flux fusion using lithium tetraborate were investigated as digestion methods. Microwave-assisted acid extraction samples were analysed with matrix-matched standards. The most successful microwave-assisted acid extractions yielded 44.3(1), 49.75(7), 78.3(3) and 90.0(7) per cent recovery for Zr, Hf, Al, and Fe respectively using sulphuric acid. In no instance was acid extraction capable of complete digestion of the sample matrix. A standard addition method was applied to the flux-fusion samples due to the high complexity of the sample matrix. Method validation for the flux fusion procedure was performed using the SARM 62 certified reference material (CRM) with acceptable recovery ranges being based on the 95 per cent confidence intervals of the CRM. Successful analyses were achieved for Zr, Hf, and Ti with apparent content of 66(6), 1.7(1) and 0.15(1) per cent respectively.

Jan 1, 2012

By H. Krogerus, P. Jokinen, T. Lintumaa

The energy consumption and recovery of chromium are important economic factors in ferrochrome production. Outokumpu has a lot of experience of the reduction behavior of the sintered pellets in industrial-scale furnaces and also on the grounds of numerous laboratory and pilot-scale investigations. Sintered pellets have shown a superiority over lumpy ore and briquettes made of the same chromite grade. The good performance of the pellets has also resulted in investigations on the reasons for such a performance. In this study, the factors affecting pellet behavior in smelting furnace were investigated. This study is divided into two sections, i.e. the investigations were on the factors affecting solid state reduction and on the factors affecting reduction under melting. These tests were performed by means of thermo gravimetry and by smelting tests. The correlation between the pellet characteristics and reduction behavior was shown and its influence on industrial-scale furnaces was discussed. Factors worth of consideration are for instance, the extent of oxidation during sintering, slag formation and chemistry in respect of molten state reduction, and the grain size of the chromite mineral in the raw material in respect of kinetic reasons (retention time in smelting).

Jan 1, 2007

By M. K. Pelser

The purpose of this paper is not so much to provide a scientific study of the selection process for the perusal of other psychometrists or industrial psychologists?the purpose is to provide line management with a practical, relatively user-friendly guide to fair and scientific selection. The main areas that are to be covered are: ? Why fair and scientific selection? ? Job analysis ? The job requirement?selection technique circle ? Assessment centres in the mining industry?the Tavistock Collieries Ltd experience. Why fair and scientific selection? Seen from a line manager?s perspective, fair and scientific selection should be pursued for two main reasons: ? to remain within the ambits of the law ? to maximize the probability of selecting the potentially most productive and efficient candidate for the job.

Jan 1, 1997

By J. Wills

The use of drilling rigs to increasingly mechanize stope drilling has been acknowledged as important for the S.A. mining industry in it ís efforts to tackle the challenges of low productivity, AIDS and an ageing driller workforce. The spin-offs of increased safety, cost-effectiveness and better mining performance provide advantages to all?from the driller to the shareholder. However, implementation or product rollout has varied from outright success to dismal failure. A study of various cases by Novatek and Anglogold TDS showed clear reasons for these differences. Whereas the successes were characterized by clear objectives, accountability, user buy-in, a commitment to make the technology work and no-nonsense reporting, these were typically absent in failed implementations. The attitude at unsuccessful mines was to ?trial? the equipment?even subconsciously, a ?trial? is a test where failure becomes an acceptable outcome. During the study it became clear that mining management are not adequately trained to manage the often-tricky rollout process. They are often also not empowered or clearly mandated to deal with the organizational, human and technical issues that must dovetail to create a success. The output of the study was to develop a basic rollout process that could be used to formally manage the implementation of new drilling technology. Creating an alignment between the mine, workforce and supplier promotes a win-win situation that will not otherwise spontaneously arise.

Jan 1, 2002

By H. C. van Zyl

Mine water in the Upper Olifants River Catchment in Mpumalanga(upstream of Loskop Dam) is at times discharged into local streams, resulting in local acidification and regional salination of surface water resources. Pollution of surface water can be prevented by collecting and treating mine water to a quality where it could be re-used without restriction (Cleanwater 2020 Initiative). Mine water in the Olifants River Catchment currently amounts to only 4,6% of the total water usage, but contributes 78,4% of the sulphate load. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. A number of alternative desalination treatment technologies were investigated (subsequent to gypsum crystallization pre-treatment) where treated mine water must meet more stringent quality requirements (e.g. less than 200 mg/lSO4). The capital cost of these processes varied between R4 million/(Ml/d) and R10million/(Ml/d) and the running cost between R2/m3and R5/m3. Water usage in the Upper Olifants River Catchment currently amounts to 947 Ml/d (including the power stations), and will increase to an estimated 1385 Ml/d by 2020. The additional water demand by2020 (438 Ml/d) will have to be supplied by importation from neighbouring catchments, and more efficient utilization of the local water resources, including excess mine water. Various levels of treatment are required to make mine water suitable for the following potential applications (acceptable treated water sulphate concentration shown in brackets): irrigation (2000 mg/l), coal processing plant (1000 mg/l), general industrial use (500 mg/l), discharge to public streams (500 mg/l), potable use (200 mg/l) and cooling water in power stations (20 to 40 mg/l). The following two options, or a combination thereof, can be considered for management of excess mine water in the Upper Olifants River Catchment: ?Collection and treatment of excess mine water to a quality suitable for selected urban and industrial applications (Option A) ?Collection and treatment of mine water to a quality suitable for irrigation (Option B). The estimated capital and running cost for Option A amounts to R528.5 million and R55.7 million/year, respectively, compared with R68,2 million and R11,9 million/year for Option B. It is recommended that Option B be investigated for implementation in the short to medium-term. Option B was selected due to cost benefits and the initial favourable results obtained by a joint Water Research Commission and Coal Industry initiative where mine water is used for irrigation. Option A may become feasible in the long-term to ensure maximum environ-mental protection and reduced treatment cost as a result of anticipated technological improvements over the next 5 to 10 years.

Jan 1, 2001

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By L. J. Leach

Quench and tempered Cr-Mo plate steel was found not to contain a fully martensitic structure as a result of either slow slack quenching or insufficient hardenability at the cooling rates used. The resulting microstructure contains bainite in combination with martensite. It is necessary to examine the implications of bainite for the toughness of the final product. Loss of toughness arises primarily from the inter-lath carbides that typically form in upper bainite. An investigation into the effect of upper bainite in a martensitic matrix of a steel grade containing 0.17% C, 0.1% Cr, 0.54% Mo, and 20 ppm Bindicated lower toughness than in a fully martensitic structure.

Jan 1, 2013

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By P. K. Hofmeyr

Base Metal (Cu, Ni, Mo, Zn, Co etc.) analysis traditionally has been very slow in conventional analytical laboratories which can lead to additional costs being incurred in waiting time of drill rigs or mining excessively off-reef. Recent developments in the automation of analytical laboratories now allow for very rapid turn-around times for base metal analytical data which can help reduce such costs as well as reduce the unit costs of the analyses themselves. 2.0 CONVENTIONAL ANALYTICAL LABORATORY PRACTICE Conventional analytical laboratories are necessarily are very manual. Sample preparation is slow and laborious, samples are moved from stage to stage manually and, typically, all samples are processed in batches so a sample which is the first to be, say, milled has to wait for the complete milling of the batch before it advances to the next stage eg. mixed with wax prior to pelletising for XRF analysis. Inevitably this results in long sample data turn-around times for laboratories handling large numbers of samples. Manual sample preparation can only be accelerated by increasing staff which increases costs and can lead to additional errors being introduced. Cleaning of sample preparation equipment, eg. crushers and mills, between samples is essential to avoid cross-contamination between samples and this is slow and labour-intensive. In manual sample preparation the correct sample numbers staying with the samples is totally dependent on the efficiency of laboratory operators. It is extremely difficult to detect when errors have occurred due to the switching of sample numbers during the sample preparation stages. Running duplicates and QC samples at best is only partially successful in detecting when sample number switching errors have occurred. Errors of this nature and cross-contamination problems due to incomplete cleaning of sample preparation equipment tend to occur when laboratories are working at pressure due to high sample numbers and when supervisors are not present during 24/7 laboratory operations which is often required on plant process control laboratories. These problems are common to all conventional analytical laboratories and their magnitude is dependent on the level of control and efficiency of QC systems practised by individual laboratories. The disadvantages of conventional manual analytical laboratories can be summarized as follows:- 1. Labour-intensive which is costly especially when multiple shifts have to be used during 24/7 operations.

Jan 1, 2005

By E. Matinde, S. L. Msibi

"The robust nature of alumina refractory materials presents opportunities for their in-process reclaiming and re-use in non-critical applications. Virgin refractories can be substituted with different quantities of reclaimed materials without compromising the quality of the refractory products. In this study, the effect of reclaimed bauxite on andalusite-containing refractory castables for tundish applications was investigated. The recycled bauxite was formulated in different proportions to replace virgin andalusite in the castables. Standard tests were conducted to evaluate the physical, physicochemical, and thermochemical properties of the formulated products. Static corrosion tests were conducted using tundish slag in order to simulate the actual operating conditions. The results show that the standard flow behaviour, open porosity, and bulk density of samples containing up to 22 mass% reclaimed bauxite were comparable to those of the reference castable. However, high-temperature properties such as static corrosion at 1400°C and hot modulus of rupture at 1500°C indicated that there is an upper constraint to the amount of substitution. The study demonstrated direct potential savings of up to 10% when the reclaimed alumina replacement ratio was increased to 22 mass%. IntroductionAlumina-based refractories can be classified into low-alumina, containing less than 50% Al2O3, and high-alumina or bauxite, containing between 50 and 90% Al2O3. High-alumina refractories have widespread applications in high-temperature metal extraction processes due to their outstanding thermochemical and thermomechanical properties and stability (Rebouillat and Rigaud, 2002; Frulli, 2016). The typical chemical composition of refractory-grade bauxite consists of 85–90 wt.% Al2O3, 5–10 wt.% SiO2, 1–2wt.% Fe2O3, 3–4 wt.% TiO2, 0.4–0.8 wt.% CaO + MgO, and 0.20–0.8 wt.% K2O + Na2O (Nyoka et al., 2013). The thermochemical and thermomechanical properties of bauxite-based refractories rely principally on the conversion of the contained silica and alumina to the highly stable corundum (?-Al2O3) and mullite (3Al2O3· 2SiO2) phases (Rebouillat and Rigaud, 2002; Hill and Sehnke, 2006; Garbers-Craig, 2008; Frulli, 2016)."

Jun 1, 2019

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

By M. Steyn

[Zr(C9H6NO)4]?(HCON(CH3)2)?(H2O), where (C9H6NO) = 8-hydroxy quinoline (oxH), was synthesized and characterized. This tetrakis-coordinated zirconium complex crystallized in the triclinic crystal system (Pi, Z=2) along with water and N,N?-dimethylformamide(DMF) solvate in the asymmetric unit. The metal atom is surrounded by four N,O-donating bidentate ox-ligands that are arranged around the metal centre to give a square antiprismatic coordination polyhedron with a small distortion towards a dodecahedral geometry. Crystal packing is stabilized by intermolecular interactions of adjacent oxine ring systems in neighbouring molecules, as well as hydrogen bonding of the aqua and DMF solvate molecules, linking the molecular entities into a supramolecular three-dimensional network.

Jan 1, 2013

By P. K. Sahoo, C. R. Ray, S. S. Rao

This paper deals with various factors affecting the strength of chromite briquettes which plays a vital role in the smelting of charge chrome / ferro chrome production. Appropriate briquetting parameters like molasses and lime binder level, molasses quality, particle size distribution and segment condition etc. are essential to guarantee quality briquettes in the successful use of briquette and chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the grain size characteristics of the chrome ore fines but also to make an informed choice of the type and quality of the binder and the condition for producing a physically and chemically competent green and cured briquette. This paper also describes the effect of strength of briquettes on various parameters of charge chrome production as the use of quality briquettes in the production of high carbon ferrochrome alloys has a number of operational, metallurgical and economic advantages. It is also a requirement for submerged arc furnace operation that the charge be adequately porous to allow gaseous products of the reduction reaction to escape from the furnace charge burden without hindrance. Otherwise, furnace material would erupt causing electrodes and furnace other equipments damage and risking the safety of the work force. The briquette, because it replaces lumpy charge but has an advantage of smaller size, allows for an uniform and porous charge so that the ascending gaseous products can escape freely. Finally this paper deals with furnace operational results with varying proportion of briquettes having same strength.

Jan 1, 2007

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

By K. M. Godiwalla, S. Ranganathan

The thermal state in submerged-arc furnaces (S.A.F.) producing ferro alloys is important for the conditions of both the grade of alloy produced as well as specific energy consumption. The temperature profile in the S.A.F. is affected by the endothermic chemical reactions and the rate of gas evolution. The gas evolution commences at about 900 C due to the reduction of iron in the ore. A first-principle-based 2-D model has been developed to predict the temperature profile in the furnace. In this study, four ores of different grades have been considered in order to simulate the thermal profile in the S.A.F. The influence of the composition of the ore on the thermal profile and its significance in rationalisation of charge distribution to optimise the process are discussed.

Jan 1, 2007

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

The risk associated with mining induced seismicity is one of the major threats to the safety and sustainability of deep underground mines. This paper describes techniques that allow site practitioners to efficiently control such risks in mines. The proposed approaches rely on ground support to strategically control seismic risk and re-entry time to tactically control this risk. The strategic approach is based on the detailed understanding of past seismicity to as certain the seismic hazard of individual sources throughout the mine. This approach also relies on assessing the potential damage that these sources can induce on nearby excavations using the excavation vulnerability potential (EVP) and rockburst damage potential (RDP) concepts proposed by Heal et al. (2006). It is then possible to investigate how to reduce the risk of experiencing damaging seismicity in mine drives by locally enhancing the ground support system. The tactical approach relies on a proposed methodology to estimate reliable re-entry times or exclusion periods based on the seismic decay following blasting. Some examples of how these techniques have been applied in Australian mines are given.

Jan 1, 2009

By G. S. Maré

Tin plating operations are of a complex nature due to the many operational variables that need to be controlled in order to create a product of required quality. The work in this report lays the basics for the control of a halogen plating operation based on the DuPont tinplating set-up with regard to the chemical make-up of the plating solution, as well as operational variables such as temperature and current density. To evaluate these aspects of the process, a rotating cathode Hull-cell set-up was used. This allowed for a laboratory scale plating arrangement that simulates industry closely with regard to chemical and hydro-dynamic considerations. Typical industry accepted standards were obtained for the values of operational variables and a ?baseline? test was conducted employing these standards. All subsequent tests conducted were benchmarked against this baseline result. A large suite of results was obtained in which it was found that changes could be made to the industry accepted norm which would improve on the stability of the operation and therefore the quality of the final tin-plated product. Examples of these results are: an increase in stannous tin concentration, an increase in sodium chloride concentration and a slightly elevated plating temperature. In addition, conditions were found that must be avoided to prevent instability and poor product quality.

Jan 1, 2010

By S. T. Johansen, C. Colomb, B. Ravary

Combustion and thermal NOx formation have been modelled using the Computational Fluid Dynamics (CFD) commercial code Fluent 6.1. The aim was to predict and give a better understanding of the combustion in electric arc furnaces for the production of ferro-silicon and silicon metal. Another important objective was to assess the impact of a number of operating parameters on the NOx formation. The CFD tools used are de-scribed with a special focus on models for species and turbulence transport. Sensitivity studies have been carried out to study the influence of several parameters: sub-models, process gas composition and distribution at the charge surface and influence of the presence of SiO. The main conclusions are: ?Using the combination of a realistic design, boundary conditions and models, the simulated NOx level is in quantitative agreement with measurements. The presence of water vapor is particularly important because of its influence on the specific heat of the mixture and resulting temperature. ?Release of significant amounts of SiO from the charge surface results in an important increase of NOx, even if we applied a simplified combustion model for SiO gas. However, because of lack of thermal and compositional data for blowing situations (when SiO flows directly from the arc cavity through open channels to the charge surface), no quantitative validation is possible. The way SiO is distributed (uniformly or as a jet) has a limited impact on the result in our computations.

Jan 1, 2007