Search Documents

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988

By A. P. Van Wyk, G. Pirnaar

The effect of vanadium on the susceptibilities of chromium and chromium-nickel steels to reversible temper embritlement was evaluated. The steels investigated were approximately equivalent to steels of as 970 Grade 708A42 and as 970 Grade 817M40, the major difference being that molybdenum had been replaced by vanadium in various concentrations. It was found that the vanadium had a detrimental effect and, in al the concentrations tested, enhanced the susceptibility to reversible temper embritlement of both the chromium and the chromium-nickel steel. The detrimental role played by vanadium in reversible temper embritlement is explained by a consideration of the effect of vanadium carbide, as well as of free vanadium, in solid solution in ferrite.

Jan 1, 1987

By P. V. Scheers

A rotating-cylinder electrode (RCE) was used to simulate the effect of flow velocity on pipe corrosion. A comparison is made between the electrochemical measurements obtained and those measured with a laboratory-scale flow loop. There is good general agreement if the speed of rotation of the RCE is adjusted to give the same value of mass transfer Coefficient as in the other system. Hence, it appears that the RCE is well suited to simulate actual flow conditions in pipes. The simultaneous effect of flow velocity and pH value on the corrosion rate of mild steel in a synthetic mine water was investigated. The i1nrease of corrosion rate was found to be more pronounced at lower pH values and, apart from a sharp increase below pH 4, the initial corrosion rate also increased at pH 7 and 6.

Jan 1, 1992

By C. H. Johannes, N. B. Strydom, C. H. Van Graan, J. G. A. Van Heerden

Note: The practical application of microclimate cooling in an underground stope in a gold mine by C. H. JOHANNES, C. H. VAN GRAAN, N. B. STRYDOM and J. G. A. VAN HEERDEN INTRODUCTION Although much information was available on the use of pre-frozen jackets as micro climate coolers in underground situations!, 2, no information was available on their performance under practical conditions in stopes. The objectives of this study were. O.F .S. Branch Minutes of the General Meeting held in the upstairs lounge at the Harmony Country Club, Harmony G.M. Co. limited, on Wednesday 12th November, 1975 at 4.00 p.m. NIM reports Report no. 343 A mineralogical investigation of gold-bearing sulphidic ore from the Florence-Devonian Mine, Barberton.(20th May, 1968; re-issued Dec. 1975). Report no. 1384 . Flotation tests on samples of Canadian copper-zinc ores. (12th Nov., 1971; re-issued Nov. 1975). The results are given of laboratory Report no. 1488 Extraction of rutile from Highveld smelter slags. (28th Sep., 1972; re. issued Nov., 1975). Report no. 1499 The production of medium -carbon ferrochromi'um. (4th Dec., 1972; reissued Nov. 1975). Report no. 1521 The dissipation of electrical power in the burden of a submerged-arc furnace. (15th Feb., 1973; re-issued Nov. 1975). Report no. 1527 The physicochemical properties of slags associated with the smelting of nickel sulphide concentrates. (21st Feb., 1973; re-issued Nov. 1975). Report no. 1544 The recovery of salable ferrochromium from material discarded by Ferrometals Limited. (11th Jun., 1973; re-issued Nov. 1975). Report no. 1547 Physicochemical and thermodynamic properties of slags in the system MgO-AlOl.5SiO2. (23rd Aug., 1973; re-issued Nov. 1975). Report no. 1548 Physicochemical properties of slags in the system MgO-Al2O3-SiO2 and their application to the technology of ferro-alloy smelting. (13th Jul., 1973; re-issued Nov. 1975). Report no. 1553 Characterization of the flotation properties of fluorspar from smallscale batch and pilotplant tests. (27th Sep., 1973; re-issued Nov. 1975). Report no. 1555 The analysis, by atomic-absorption spectrophotometry, of matte-leach residues. (2nd Oct., 1973; re-issued Nov. 1975). Report no. 1590 The separation of osmium from ruthenium in hydrochloric acid solutions. (18th Jan., 1974; re-issued Oct. 1975.) Report no. 1606 The electrical-resistance characteristics of the charge in the electric reduction furnace. (1st Feb., 1974; re-issued Oct. 1975). Report no. 1622 The electrical conductivity of the charge in a ferrosilicon furnace. (2nd Apr., 1974; reissued Oct. 1975).

Jan 3, 1976

By N. Coulson, P. Ledwaba

"The University of the Witwatersrand presents an accredited four-course training programme for community relations practitioners (CRPs). Between May 2013 and October 2014 six courses were facilitated for 145 participants, of whom 82% were from sub-Saharan Africa, 62% worked in mining, and 58% worked directly with communities. Thematic analysis of the comments of course participants collected during course exercises found that there were a set of coherent drivers for resilient companycommunity relationships, but that the restrainers to resilient relationships were often context-specific and dominated by politics. CRPs reported facing as many difficulties in the internal company environment as in the external environment. These findings for CRPs in Africa resonate with those worldwide.InroductionMuch has changed in how the extractive industry responds to social and community issues. There has been a growing prioritization of community-related issues within the extractive industry globally (Kemp, 2010; Tatar, n.d.). According to Kemp (2010) this can be attributed partly to escalating pressure from local-level stakeholders to push mining companies to take greater responsibility for the social, economic, and environmental impacts of mining. Securing and maintaining the social licence to operate is ranked fourth in terms of the top risks facing the mining and metals industry in 2016, up one place from 2015 (Ernst & Young, 2016).Conflicts between local communities and large-scale mining companies arise because of the social, environmental, and economic impacts of mining. Worldwide, large-scale mining companies have a poor reputation amongst communities, including those in Africa (Gilberthorpe and Banks, 2012; Kemp and Owen, 2013a; van Wyk, n.d.). For mining companies, conflicts for whatever reason, result in loss of productivity, lost opportunities, lost time, and adverse impacts on reputation (International Council on Mining and Metals, 2015). Conflicts also have a significant financial impact on mining operations (Franks et al., 2014). Davis and Franks (2014), estimated that US$10 000–50 000 is lost each day when a project is delayed during the exploration phase, and about US$20 million per week when in operation. Today these costs could be expected to be higher due to increasing input costs."

Jan 1, 2017

By P. R. Jochens, D. D. Howat, R. B. Atmore

INTRODUCTION The Miller chlorination process has assumed a preeminent position in the refining of gold bullion, a position it has maintained for over half a century. In the early sixties considerable interest was aroused by the idea of producing a consistently high grade bullion at the mine smelthouses themselves. However, as the use of chlorine in industrial plants is associated with considerable hazards, oxygen was considered a natural alternative, apart from bing less expensive than chlorine. Partial refining at the mine smelthouses would considerably decrease the requirements made on Rand Refinery Limited as well as indicating the possibility of reducing final refining costs. An added factor would be the purer silver chloride obtainable, after prior removal of the base metals by oxygen injection, which would facilitate the production of high-purity silver. The free energies of formation of the oxides of the metals;- silver, copper, lead, zinc, iron and bismuth indicate that, with the exception of silver, these metals should be capable of removal as oxides by oxygen injection. Rose1 had shown that during injection of gold bullion, considerable loss of silver to the boraxsilver slag occurred and, furthermore, that copper removal was not efficient and oxide attack on the refractories was severe. Plant test work2 had confirmed the difficulty of copper removal, but had shown that zinc and lead were almost completely removed. The difficulty of copper removal by oxygen injection warranted further investigation. Also, the high decomposition pressure of silver oxide suggested that by suitable control of the slag composition it might be possible to reduce to very small proportions the silver carried into the slag as oxide. The oxidation of copper by oxygen injection and subsequent dissolution of the oxide in a slag may occur according to the following reactions; Reactions 4 and 5 were considered because of the relatively high solubility of oxygen in molten silver and silver alloys. Thermodynamic data indicate that there is little possibility of any reaction involving the formation of CuO occurring at temperatures above 1 000 °C. To ensure that the operative reactions 1 and 4 take place to the maximum extent, the following factors He significant. (a) an increase in the activity of the copper in the bullion, (b) an increase in the partial pressure of oxygen in the system, (c) an increase in the activity of the oxygen in solution in the metal, (d) a decrease in the activity of cuprous oxide in the slag. From practical considerations, the operative variable most easily susceptible to control is the composition of the slag. SOLUBILITY OF COPPER OXIDES IN BOROSILICATE SLAGS Very scanty information exists on systems containing copper oxides but the indications are that slags containing considerable amounts of boric oxide would possibly prove to be the best solvents for cuprous and cupric oxides. This is attributed to the fact that the activities of copper oxides are much lower in boric oxide slags than in slags in which silica is the main network former. The number of possible slags containing boric oxide was limited by consideration of liquidus temperature, viscosity, corrosive action on refractories, volatilization, and ultimately cost (for industrial application). Slags in the systems soda-boric oxide-silica and lime-boric oxide-silica were selected paying due attention to the above limitations. Additions of 5, 10 and 15 per cent cupric oxide were made to the finely ground, premelted slags. These mixtures were then reground and 2g quantities held in re crystallized alumina crucibles at temperatures of 1150°C and 1 250°C respectively for 30 minutes. The crucibles were removed from the furnace, rapidly cooled, cut in half longitudinally, and a thin section taken from one half was subjected to microscopic examination.

By D. D. Howat, J. van der Colf

Selected members of the slag system were reduced in graphite crucibles in an argon atmosphere, and the physicochemical properties of the reduced derivatives of the slags were determined in inert crucibles. It was found that slags having magnesium aluminium titanate as the primary phase before reduction underwent an increase in liquidus temperature, accompanied by a change in the primary phase. No analogous behaviour could be detected for the slags having perovskite as the initial primary crystallization product. In most instances, the viscosity of the melt passed through an initial minimum, followed by an increase as the reduction time was extended. Increased MgO/CaO ratio. basicity, titania content, and reduction temperature all served to accelerate thickening. During reduction, the electrical conductivity of the slags tended to rise relative to the value for the unreduced melt.

Jan 1, 1979

By F. P. A. Robinson, J. W. Fourie

Austenitic stainless steels are welded using low-heat inputs. However, owing to differences in the physical metallurgy of austenitic stainless steels and duplex stainless steels, low-heat inputs should be avoided for duplex stainless steels. This paper highlights the differences in solidification mode and transformation characteristics of these two types of alloys. Recent work on the effect of heat input on the properties of weldments of duplex stainless steels is reviewed.

Jan 1, 1990

By D. Royston

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By M. J. Nicol

The results are reported of experiments on the influence of a number of variables on the rate of loading of gold cyanide onto activated carbon and the equilibrium capacity of the carbon. These variables include the concentrations of gold and free cyanide in solution, the pH value and ionic strength of the solution, the concentration of organic compounds in the solution, the temperature, the particle size of the carbon, and the mixing efficiency. The experiments were carried out under approximately steady-state conditions to simulate the conditions in a countercurrent carbon-in-pulp absorption plant. In addition, the results are reported of experiments to establish whether the absorption of gold cyanide onto activated carbon is a reversible process.

Jan 1, 1983

The above paper is an important contribution to the field of physicochemical studies in ferromanganese production. The authors are to be congratulated on the well planned and competently executed experimental work and on the interpretation of the data. Although the paper is essentially descriptive, the results lend themselves to thermodynamic interpretation (but in such a complex system as that studied this cannot be done rigorously), as well as to an examination of the probable reduction mechanisms that operate at various stages.

Jan 1, 1979

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

By S. Kahraman

P-wave velocity measurements were carried out on 22 large limestone blocks in a stone processing plant. In the laboratory, P-wave velocity of core samples was measured to obtain intact rock velocity. The square root of the ratio of the velocity of the large stone block to the velocity of the core specimen was called the velocity ratio index (VRI) and a quality classification for large building stones was suggested. In addition, the applicability of the established classification to stone cutting with gang saws was checked. It was concluded that the quality classification and estimation of slab production efficiency of the building stones can easily be made by ultrasonic measurements. However, the study was carried out only in limestone. Further study must be conducted to check the validity of the obtained results for the other rock types.

Jan 1, 2007

By A. Hoogervorst

Cyanide is a key contributor to the efficiency of gold extraction. Public perceptions of cyanide are emotive and following some publicised incidents involving cyanide, the gold mining industry established a voluntary cyanide code for the manufacture, transport and use of cyanide in the production of gold. The paper describes the development of the code, its content and the third party auditing of the code as a means of establishing and maintaining benchmark standards. In adhering to the cyanide code requirements, there are overlaps with other management systems such as ISO 14001 and OHASA 18001 and the paper seeks to show how existing mine systems can readily accommodate cyanide code compliance and that operating and auditing the cyanide code can assist in the integration of mine heath, safety and environmental management systems.

Jan 1, 2009

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

By E. L. Atkinson, G. W. Leach

The paper discusses the reasons for the introduction of load-haul-dump (LHD) units into Greenside Colliery, and the circumstances leading to the replacement of conventional mechanized equipment on a trial basis in the mining operations on No. 2, 4, and 5 seams. An outline is given of the factors governing the selection and introduction of these units into coal mining, and the associated mining and engineering aspects involved in the optimization of their use. Operating statistics comparing the performance of conventional and LHD equipment are included.

Jan 1, 1979

By J. Petersen, H. Naderi, H. Zare, M. H. Nikzad, M. Karimi

In the copper electrorefining process, the dissolution of anodes is significantly reduced or even stopped when the passivation phenomenon occurs. The results of this phenomenon are increasing energy consumption, residual formatting, and voltage levels in the cell. In this study, the electrochemical behaviour of blister copper in the presence of sodium persulfate (PDS) was studied. The electrochemical methods of LPR, Tafel, and Electrochemical Impedance Spectroscopy (EIS) were used. The results showed that the addition of sodium persulfate activates the electrode surface and increases the open circuit potential. In the presence of PDS, the polarisation resistance of the electrode shows an increasing or decreasing tendency, based on the PDS concentration. This tendency is probably due to the formation of surface layers (such as slime layer or copper sulfate) and dissolution of this layer at various concentrations of PDS. The lowest polarisation resistance of 1.8 ohms and the highest corrosion current of 60.6×10-3 and 36.6×10-3 A/cm2 from LPR and Tafel techniques respectively were obtained at the concentration of 40 g/l PDS. Based on the results of potentiodynamic and electrochemical impedance spectroscopy tests, the addition of sodium persulfate to the solution reduces the corrosion resistance, therefore the passivation time of the blister copper anode increases. Keywords: Blister copper, electrorefining, sodium persulfate, anodic passivation

Jan 1, 2020

By D. R. Arnold

Discussion of the above paper by D. R. ARNOLDt This paper is the result of an excellent piece of work performed as a service to hyUrometallurgy in general and to the South African uranium industry in particular, and the authors are to be congratulated, Authors' reply Dr Arnold is correct in saying that the present Senbrix resins, which are based on the experimental heavy resins first developed at the National Institute for Metallurgy (NIM), need not necessarily show the same poor performance with respect to cobalt poisoning as the NIM prototypes. Oceanology International The next 01 World Conference is to be held Brighton, England, from 2nd to 7th March, 1980. The programme will concern technical advances in the offshore oil and gas industries, and is expected to include 140 papers from 20 countries.

Jan 1, 1979

By Sh. Arshadnejad

Stress analysis in a rock medium is essential to determine the stress concentration between two consecutive circular holes and prediction of fracture behaviour. When two consecutive circular holes in a hard rock medium such as granite are loaded internally by the pressure of non-explosive expansion material (NEEM), stress concentration occurs between the holes which then causes the rock to fracture. In this work, finite element (FE) analysis using Phase2 code was employed to study the stress concentration between two consecutive circular holes under internal pressure induced by NEEM. Effects of different hole diameters and spacings, rock properties and NEEM pressures have been analysed. The data gained from the numerical analysis and analytical solutions were then used to develop two models. These models were then modified by using the FE data and polynomial regression analysis. The developed analytical models showed to be in a very good agreement with the FE analysis. Hence, the developed models can be used with confidence to determine stress distribution and concentration factors around two consecutive circular holes in a hard and brittle rock which are loaded internally by the pressure induced from the NEEM. Keywords Finite element method, non-explosive, quarry mining, stress concentration..

Jan 1, 2011

By H. P. Carlisle

The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E. FEATHER and G. M. KOEN Published in the Journal. February 1973. DISCUSSION H. P. Carlisle. B.Sc. (Eng.) Rand (Fellow) The authors are to be congratulated on drawing attention to the importance of surface characteristics in the treatment of gold grains. I must, however, confess to considerable doubts about the validity of the distribution of gold in "free" and "locked" form set out in Tables I to IV.