Search Documents

By A. Singh, K. Bisaka, G. Marape, T. Mokgomola

This paper investigated the pre-concentration amenability of sovite (carbonatite) ore to enhance the grade of rare earth elements (REE) bearing minerals by rejecting calcite, and to improve total rare earth elements (TREE) recovery using gravity and magnetic separation. A high proportion of calcite affects downstream processes like leaching due to high acid consumption. Multiple flowsheets combining gravity and magnetic separation were employed to target > 60% TREEs recovery to the final concentrate and > 60% calcite rejection to the tailings. Head analysis of the feed showed the sample’s main constituents as Fe (15.61%), Ca (16.04%), SiO2 (7.13%), and lastly TREEs (1.12%). Mineralogy liberation data at 2mm top size indicated poor liberation of TREEs, with the majority of minerals displaying < 30% mass greater than 80% liberated. Grain size distribution data showed that the majority of REE minerals are fine grained and report to the < 20 μm size class. Calcite liberation mineralogy showed < 60% mass greater than 80% liberation.A combination of a single-stage shaking table with a wet high intensity magnetic separator at a magnetic intensity of 7520 G was found to be the optimum flowsheet. For a shaking table feed with P80 of 150 μm followed by tails regrind to P80 of 45 μm as feed to wet high intensity magnetic separator, the overall mass balance results showed that 60.5% TREEs are recovered to the concentrate while 63.0% calcite is rejected to the tails. However, due to the fine-grained nature of This paper investigated the pre-concentration amenability of sovite (carbonatite) ore to enhance the grade of rare earth elements (REE) bearing minerals by rejecting calcite, and to improve total rare earth elements (TREE) recovery using gravity and magnetic separation. A high proportion of calcite affects downstream processes like leaching due to high acid consumption. Multiple flowsheets combining gravity and magnetic separation were employed to target > 60% TREEs recovery to the final concentrate and > 60% calcite rejection to the tailings. Head analysis of the feed showed the sample’s main constituents as Fe (15.61%), Ca (16.04%), SiO2 (7.13%), and lastly TREEs (1.12%). Mineralogy liberation data at 2mm top size indicated poor liberation of TREEs, with the majority of minerals displaying < 30% mass greater than 80% liberated. Grain size distribution data showed that the majority of REE minerals are fine grained and report to the < 20 μm size class. Calcite liberation mineralogy showed < 60% mass greater than 80% liberation.A combination of a single-stage shaking table with a wet high intensity magnetic separator at a magnetic intensity of 7520 G was found to be the optimum flowsheet. For a shaking table feed with P80 of 150 μm followed by tails regrind to P80 of 45 μm as feed to wet high intensity magnetic separator, the overall mass balance results showed that 60.5% TREEs are recovered to the concentrate while 63.0% calcite is rejected to the tails. However, due to the fine-grained nature of TREEs, no flowsheet improved their grade.

Nov 6, 2024

By G. R. Baiden

Introduction The introduction of teleremote systems to underground mining can provide a significant improvement in the performance of a mine when compared with conventional mining techniques. This paper presents the concepts of teleremote mining in a case study showing how the systems work and the competitive advantage autonomation of mining techniques will provide for underground metal mining operations into the future. This paper is divided into two sections: the Mining Automation Program and What is next? On January 1st 1996 Inco Limited, Tamrock Oy, DYNO Explosives Group and CANMET formed a consortium for the development of teleremote mining equipment called the ‘Mining Automation Program’ or MAP. This program included a five-year research and development agreement that combines the talents of the above organizations to create mining equipment and systems for autonomating mining. The projects are based on the communication system currently sold and marketed by Automated Mining Systems Limited. The main components of the program investigated the development of a positioning and navigation module, autonomated systems using teleremote techniques for development and stoping, and software systems to support the use of this equipment. The program included the establishment of a test mine, at Inco’s 175 Orebody near Copper Cliff North Mine. This facility was unique allowing collaboration of companies and research organizations inthe design and testing of techniques and equipment used to apply autonomation to mining. Since the inception of the project other research alliances have been added to enhance the program. These include the application of ground support (Meyco/ Master Builders), muck pile recognition, the broadening of telecommunications links (PRECARN Associates Inc.-MALTA project) and the collection and processing of drilling core through the automated diamond drilling project (J.K.S. Boyles). MAP began as an idea a number of years ago with the fundamental question ‘Can an ore-body be profitably mined through autonomation?’ The concept was to design mining equipment and systems that would allow the teleremote operation of a mine. Automation was only one componentof this much larger teleremote mining issue. To start with, it was essential to prove or disprove the feasibility of this concept. The fundamental requirements are: • Telecommunications • Positioning • Navigation • Equipment • Software • Electronics • Mining Engineering • Organization. Each of these had to be considered. Technically, the feasibility of the project hinged on the successful development of a high capacity communication network, an accurate underground positioning system, a navigation system and finally the electronics and software that could integrate these. Mining equipment that could perform all the mining functions was the next requirement, along with explosive supplies that could be delivered to the holes teleremotely. Whatever the systems developed, they must be able to work in both bulk and selective mining situations and in varying conditions within a mine. Finally, the organizational issues of a change from our current method of operation to teleremote mining had to be understood. After five years of research and development the answer to the question ‘Can an orebody be profitably mined using autonomation techniques?’ is YES! There are still hurdles to overcome, however, the basic premise has been proven. The development and production of underground tunnels and stopes has been done. There have been interesting outcomes in terms of reduced effort to accomplish mining and the total time to mine. Definitions •Automationis the process by which a machine or system is run continuously including the ability for the system to self-correct. •Autonomationis the same as automation except that the process does not self-correct. •Teleremote operation is the operation of mining equipment over a network from any location out of line-of-sight of the machine. •Equipment Automationis the addition of technology to a machine that allows for unmanned operation of a machine and thus enhances the productivity of the operator. For example, a guidance system that allows a load-haul-dump to drive by itself, thus freeing the operator for other tasks. •Teleremote mining describes a mine process that combines the use of teleremote operation (potentially with some automation), positioning and process engineering, monitoring and control. •Tamrock DataSoloTMis a computerized drilling rig as shown in Figure 1. •Tamrock DataMini™ is a computerized development drill rig used for drifting and construction tunneling as shown in Figure 2.•Tamrock Toro 450™ is a LHD (Figure 3).

Sep 1, 2001

By M. Smit, N. C. J. Dempers, S. Lunkov, C. Saguru, J. Nel

A common method for the recovery of copper is by heap leaching, solvent extraction, and electrowinning. During solvent extraction, the solution is continuously recycled, and it is necessary to remove impurities that build up in the raffinate. For the process investigated in this study, the main impurities include Fe, Co, As, and Zn. Recovery of these impurities can provide economic benefits while adhering to legal and environmental constraints. Such impurities are often removed by precipitation utilizing a neutralizing agent, such as limestone or lime, but it is also possible to remove the impurities by sulfide precipitation. Sodium hydrosulfide (NaHS) is used to selectively precipitate copper, arsenic, and zinc from a solvent-extraction raffinate stream. The resulting sulfide precipitate is bagged and sent to a roaster for further treatment. The design of the sulfide precipitation was investigated to optimize the processing conditions (including temperature, pressure, and residence time), the materials of construction, and the toxicity and explosive nature of the hydrogen sulfide gas produced

Jan 1, 2023

PREFACE During the past year, the Council of the SAIMM undertook a major strategic-planning exercise to review all its current activities, and to redefine its scope and objectives in the light of changing circumstances. The following are the four main concerns that prompted Council to take stock of the situation. (1) Over the past five years, the SAIMM has become heavily involved in a variety of new activities. (There are many examples, of which the expansion in book publications and the establishment of physical metallurgy as a third major discipline with its own colloquia and schools are perhaps the most important.) While these new activities have considerably broadened the SAIMM&apos;s scope, they have resulted in a significant increase in the day-to-day workload of the President, Office Bearers, and Council members, and of the secretarial staff based at Kelvin House.

Jan 1, 1986

Hydrometallurgical processing of complex ores and concentrates is becoming increasingly important as the mining and metallurgical industry seeks to exploit mineral deposits that are difficult to treat using conventional mineral processing and pyrometallurgical technologies. Mineral processing is often challenged by the difficulty or inability to separate valuable minerals into marketable concentrates. Hydrometallurgical processing, using selective leaching technology, can often ?chemically beneficiate? such difficult deposits. Pyrometallurgical treatment of base metal concentrates is capital intensive and subject to ever more stringent environmental control. Hydrometallurgical processing is generally lower in capital cost for an equivalent metal production rate and avoids the gas and dust issues associated with pyrometallurgical processing. The possibility of by-product recovery may also increase with hydrometallurgical treatment. Two examples of new technology or flowsheet development for treatment of complex ores and concentrates are used as illustration. These include the El Boleo process of Baja Mining for recovery of copper, cobalt, zinc and manganese from a complex clayey ore and the PLATSOL? process for recovery of copper, nickel, cobalt, platinum, palladium and gold from a bulk sulphide concentrate.

Jan 1, 2009

By T. Song, X. Wang, X. O. Xia, X. J. Luo, B. Chen

Interparticle breakage is the main crushing mode of an inertia cone crusher according to its working principle and feeding condition. In this paper the breakage behaviour of an inertia cone crusher is investigated, based on energy controlled compression combined with the vibration theory, rather than geometry controlled compression (form conditioned) which plays a major role in conventional eccentric cone crushers. The effect of feeding and operating conditions on breakage behaviour was described quantitatively from the perspective of energy consumption and product size distribution. The influence of feeding conditions, discharge size settings and vibration exciter speeds on the crushing process and product quality has been studied according to the results of laboratory crushing experiments. The results of the experiments show that the particle size of broken products becomes finer with the decrease of a discharge gap within the gap range selected by the experiment. The product size increases significantly when the gap approaches the upper limit of 6 mm. The variation of eccentric speed has a more prominent effect on reducing the product size compared with the change of discharge gap. The change in product size is not apparent when the eccentric speed rises to a certain level. The throughput of an inertia cone crusher is sensitive to the change of discharge gap, which increases linearly with the discharge gap and decreases with the eccentric speed. The change of feeding conditions has little influence on the crusher throughput. Keywords: Inertia cone crusher, interparticle breakage, energy consumption, product size distribution

Jan 1, 2020

Advanced process and equipment analytics have been around for a while. However, with accessible IT infrastructure and site maturity, it is possible to analyse, monitor, and control processing plants and equipment easily. These various disparate systems provide different reports requiring the involvement of various personnel and attention to different reporting platforms. For efficient harnessing of the systems? capabilities, as well as effective improvement and monitoring of process and equipment, a single point of entry is required. A process and equipment optimization solution was required at a concentrator in South Africa, focussing on the product stream of platinum group metal (PGM) concentrate from the UG2 Reef. The investigation of data to identify strategies for optimization was required to allow visibility into plant operations to guide operators, an easier method to identify process loop problems, identification of imminent equipment failures, and advanced process control to optimize throughput and stability. A collaborative effort between the client and General Electric Intelligent Platforms (GEIP) investigated data-driven solutions to each of the problems. With the focus on process optimization and asset monitoring, as well as equipment monitoring, a combination of approaches was utilized to address the various problem areas that were identified. Each was implemented separately in the control layer of the plant IT infrastructure. The integration was done in a centralized web-based reporting tool that integrated the detailed results from the various solutions. On the process control side, monitoring of control loops was included by calculating performance statistics that were reported daily to identify sub-optimally performing control loops and indicating potential problems. The advanced process control solution for this site includes a surge tank controller, stabilizing flow through the flotation banks, and preventing the surge tank from overflowing or running empty. Equipment monitoring was investigated, for preventative maintenance, by making use of statistical data models to indicate imminent equipment failure. These predicted alarm events included the cause for failure, drilling down, and allowing focus on a specific variable for preventative action. The results included a more stable flow through the mill, with fewer stoppages due to surge tank overflows or running empty. The causes for process drift could be identified and operators could react early. Alarms warning of equipment failure 2½ and 4 months in advance were identified in an offline analysis.

Jan 1, 2012

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By R. T. Rudd

DISCUSSION R. T. RUDD I have the following comments on Mr Bosman&apos;s paper. Before giving the company permission to discharge neutralized mine drainage containing 1800 mg/l of dissolved solids into a public stream, my Department had to consider the matter from both the legal and the practical viewpoint.

Jan 4, 1974

By I. Mitov, A. Stoilova, D. Krastev, B. Yordanov

We present three technological scenarios for the recovery of valuable components from gangue, stored in the tailings dam at Kremikovtzi metallurgical plant in Bulgaria, into marketable iron-containing pellets. In the first approach the iron concentrate was recovered through a two-stage flotation process, desliming, and magnetic separation. In the second proposed process, the iron concentrate was subjected to four sequential stages of magnetic separation coupled with selective magnetic flocculation. The third route entails the not very common practice of magnetizing roasting, followed by selective magnetic flocculation, desliming, and magnetic separation. The iron concentrate was pelletized in a laboratoryscale pelletizer. Each technology has been assessed with regard to the mass yield of iron concentrate, the iron recovery. and the iron, lead, and zinc content in order to identify the most effective route.

May 1, 2021

By Y. Cao, C. Li, A. Song

Bubble size plays a key role in determining flotation efficiency. Bubbles can be formed by passing air through pores. Bubble detachment from a pore is driven by lifting forces including buoyancy force and momentum force. Enhancing the momentum force is the key to accelerate bubble detachment and to minimise bubble size. Recent studies show that replacing steady air with oscillatory air supply could significantly decrease bubble size by enhancing the momentum force. To date, the underlying mechanism for the improved momentum force with oscillatory air supply is not yet clear. This work, for the first time, developed a qualitative model for the momentum force as a function of frequency, on/off time ratio and gas flow rate. It was found that the momentum force was positively correlated with the frequency as well as the air flow rate, and was negatively related to the on/off time ratio. The relation between bubble size and these operating parameters was also investigated. Keywords: Flotation, bubble size, momentum force, modelling, oscillatory air supply

Jan 1, 2020

Council and Standing Committees-1984/85 President: J.D. Austin Vice Presidents: H.E. James and Dr H. Wagner Immediate Past President: Prof. R.P. King Honorary Treasurer: Prof. D.G. Krige Members of Council: B.C. Alberts, Prof. S. Budavari, E.B. Crocker, N.J. Devine, C.E. Fivaz, J.S. Freer, Prof. G.G. Garrett, J.J. Geldenhuys, Dr A.K. Haines, R.W.O. Kersten, Dr B.K. Loveday, I.D. Matthews, G. Maude, H.G. Mosenthal, B.E. Protheroe, Dr O.K.H. Steffen, Dr P.T. Wedepohl Chairman, Witbank/Middelburg Branch: W.C. Mather Chairman, Orange Free State/Klerksdorp Branch: Dr M.A. Orridge Past Presidents Serving on Council: Dr M.G. Atmore, Prof. A.N. Brown, Dr P.R. Jochens, G.Y. Nisbet, Prof. R.P. Plewman, Dr R.E. Robinson, Prof. M.D.G. Salamon, P.W.J. van Rensburg, D.A. Viljoen, P.A. von Wielligh Standing Committee Chairmen: Adjudication, Prof. R.P. King; Awards, Prof. R.P. King; Constitution, Rules and Policy, Prof. R.P. King; Excursions and Banquet, B.E. Protheroe; Journal, H.E. James; Membership, Dr H. Wagner; Phoenix National Committee, Dr M.G. Atmore; SAIMM School-Extractive Metallurgy, J.S. Freer; SAIMM School-Mining, Prof. S. Budavari; Special Publications, J.D. Austin; Technical Programme¬Extractive Metallurgy, Dr B.K. Loveday; Technical Programme-Mining, J.J. Geldenhuys; Technical Programme-Physical Metallurgy, Dr P.T. Wedepohl; Training, Career Guidance and Education, Prof. R.P. King; World Mining Congress-National Committee, Prof. R.P. Plewman; Working Group Physical Metallurgy, Prof. G. G. Garrett

Jan 1, 1985

By A. M. Engelbrecht

Paper written on project work carried out in partial fulfilment of B Eng. (Chemical) Membrane processes are vital to a diverse range of technical and biological systems, which also feature in mineral processing applications such as the treatment of mine effluent and extraction of metals. In this study, the use of cellular automata to model a semi-permeable membrane that separates two compartments is considered. Cellular automata are simple models that enable the analyst to represent well-understood local effects, such as the chemical or steric interaction between molecules themselves and between molecules or particles and their environment, which can lead to very complex behaviour on a macroscopic scale. Various physical phenomena, including reverse osmosis, were simulated. Initial results for the effect of temperature, membrane structure and chemical properties of the solutes on the performance of the membrane appear promising. Keywords: cellular automata, dynamic modelling, filtration, membrane fouling, osmosis.

Jan 1, 2007

Council and Standing Committees, 1978-1979 President: Dr M. G. Atmore. Vice-Presidents: D. A. Viljoen and Dr P. R. Jochens. Honorary Treasurer: J. K. E. Douglas. Immediate Past President: P. A. von Wielligh. Members of Council: J. D. Austin, A. N. Brown, H. E. James, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, C. S. McPhail, J. C. Mostert, G. Y. Nisbet, H. G. M. Rose, W. T. Ruhmer, G. C. Thompson, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: T. S. Wilmot. Chairman, Orange Free State-Klerksdorp Branch: H. M. W. Eschenburg. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg. Standing Committee Chairmen: Membership, Dr P. R. Jochens ; Technical Programme - Metallurgy, Prof. R. P. King ; Technical Programme - Mining, H. G. M. Rose; Vacation School - Metallurgy, J. C. Mostert; Vacation School - Mining, D. G. Malan/J. D. Austin; Awards, P. A. von Wielligh; Excursions, D. A. Viljoen; Adjudication, P. A. von Wielligh; Constitution, Rules and Policy, P. A. von Wielligh; Monograph Series, Dr R. E. Robinson; Professional and Technician Train¬ing Committee, Dr M. D. G. Salamon; Career Guidance, D. G. Malan; Phoenix National Committee, Dr R. E. Robinson; 1982 World Congress, Dr M. G. Atmore; Witbank Coal Colloquium, Dr P. R. Jochens; Mines and Works, P. A. von Wielligh.

Jan 1, 1979

Council and Standing Committees, 1979-1980 President: D. A. Viljoen. Senior Vice-President: Dr P. R. Jochens. Junior Vice-President: G. Y. Nisbet. Honorary Treasurer: Dr D. G. Krige. Immediate Past President: Dr M. G. Atmore. Members of Council: J. D. Austin, A. N. Brown, J. A. Cruise, C. E. Fivaz, J. S. Freer, P. N. Harris, H. E. James, Dr R. P. King, Prof. F. Q. P. Leiding, Dr B. K. Love¬day, D. G. Malan, C. S. Macphail, J. C. Mostert, H. G. M. Rose, G. C. Thompson, R. A. von Maltitz, Dr H. Wagner. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plowman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg, P. A. von Wielligh. Chairman, Witbank-Middelburg Branch: R. B. Smith. Chairman, Orange Free State-Klerksdorp Branch: W. C. Mather. Materials Engineering Division, Chairman: Dr J. P. Hugo. Secretary: G. Pienaar. Standing Committee Chairmen: Membership, G. Y. Nisbet; Technical Programme Metallurgy, H. E. James, (Prof. R. P. King) ; Technical Programme Mining, H. G. M. Rose; Vacation School Metallurgy, J. C. Mos¬tert; Vacation School Mining, J. D. Austin; Awards, Dr M. G. Atmore ; Excursions, A. N. Brown ; Adjudications, Dr M. G. Atmore ; Constitution, Rules, and Policy, Dr M. G. Atmore ; Monograph Series, Dr M. G. Atmore ; Training and Career Guidance, P. A. von Wielligh (D. G. Malan) ; National Phoenix Committee, Dr R. E. Robin¬son; 1982 Council of Mining and Metallurgical Congress, Dr M. G. Atmore ; Mines and Works, Dr M. G. Atmore.

Jan 1, 1980

By R. D. Hancock

The complex responsible for the poisoning of anion-exchange resins is identified as the anionic cobaltic penta¬cyanide mono aquo species. It is shown that, at high concentration, this species polymerizes in solutions of pH less than 9. A mechanism for poisoning is presented that involves adsorption of anionic cobalt cyanide by a normal ion-exchange process, followed by polymerization within the resin matrix to form complexes that are too large to diffuse readily through the resin pores. The effects of resin structure and functionality on the extent of cobalt poisoning are examined, and the effect of cobalt poisoning on the kinetics and equilibrium loading of uranium is discussed.

Jan 1, 1979

Council and Standing Committees - 1982/83 President: Prof. A. N. Brown Vice Presidents: Prof. R. P. King and J. D. Austin Honorary Treasurer: Prof. D. G. Krige Immediate Past President: G. Y. Nisbet Members of Council: B. C. Alberts, R. H. English, P. T. Fewell, C. E. Fivaz, J. S. Freer, Prof. G. G. Garrett, J. J. Geldenhuys, Dr A. K. Haines, P. N. Harris, H. E. James, Dr B. K. Loveday, Dr J. Lurie, D. G. Malan, G. Pienaar, B. E. Protheroe, Dr 0. K. H. Steffen, G. C. Thompson, Dr H. Wagner, Dr P. T. Wedepohl. Chairman, Witbank/Middelburg Branch: H. C. van Zyl.

Jan 1, 1983

By G. T. Lineberry, C. M. Baird, D. L. Silverstein

The University of Kentucky (UK), with an enrollment of 25,891 in fall 2002, is a comprehensive, public land-grant university located in the Bluegrass Region of Central Kentucky. As the State’s flagship university, UK has long been involved in distance education, first through traditional correspondence courses, followed by use of videotape and satellite delivery in the 1970s and1980s, but soon supplanted by use of interactive television (ITV) and on-line course delivery in the 1990s to date. Today, UK Distance Learning Programs annually administers approximately600 course sections, with services provided to over 5200 enrollees. Courses are offered via six media: interactive video, Internet, on-site, satellite, open-air and cable television, and videotape, with hybrid delivery becoming increasingly popular. The University of Kentucky College of Engineering experience with distance instruction prior to 1985 was limited to videotape non-credit offerings. The Department of Mining Engineering, a small department in terms of numbers of both faculty and students, was a University pioneer in distance education. The first University degree program offered in its entirety by distance delivery(initially by itinerant faculty) was the Master of Mining Engineering. Satellite delivery from Lexington to Cumberland, Kentucky, was a welcomed change of delivery mode in 1987–88,resulting in six hours less travel time for faculty each week. Shortly thereafter, other initiatives directed toward fulfilment of its land-grant mission were undertaken by the College. Use of satellite for course delivery rapidly declined due to limited interactivity, in favour of compressed video and on-site instruction. Classroom sites in the Kentucky Tele-Linking Network (KTLN) now number over 200. The Network links schools, colleges and universities, as well as public and private agencies throughout the State. The KTLN supports voice, video, and data transmission in a uniformly-equipped environment. Beginning in the early 1990s, transfer-critical pre-engineering courses were delivered from Lexington to Kentucky’s community colleges with the largest pre-engineering enrolments. Success was limited, but lessons learned were invaluable. In 1996, the University of Kentucky College of Engineering was asked by the Kentucky Council on Higher Education (the predecessor to the Council on Postsecondary Education) to expand engineering education in Kentucky, first by initiating cooperative B.Sc. degree programmes in Chemical Engineering and Mechanical Engineering on the campus of Paducah Community College (PCC), located 400 km from the UK campus in Lexington. The third partner in these programmes is Murray State University (MuSU), a public regional comprehensive university 80 km south of Paducah. The genesis of the new degree programmes, which were subjected to ABET review in October 2002, as well as a summary of the major accomplishments and challenges of the innovative programmes, will be offered. The limited use of distance technologies for course delivery in these B.Sc. degree programmes will be discussed. A ‘no-spin’ overview of other non-traditional distance-learning ventures within the College of Engineering will be chronicled, with an honest assessment of the motivation for these efforts and, where appropriate, their relative degree of success. Among these ventures are: a BScME and a Master of Engineering programme at Toyota Motor Manufacturing of Kentucky, Georgetown, Kentucky; course exchange in Chemical Engineering between the University of Kentucky and the University of Louisville; an ITV-based Master of Engineering programme for practicing engineers in Kentucky; proposed joint-degree programmes in Civil Engineering and Mechanical Engineering with Western Kentucky University; and a proposed part-time MScME programme in Paducah, Kentucky, with a start date of August 2002, threshold enrolment permitting. Keywords: distance learning, distance education.

Jan 1, 2003

Council and Standing Committees, 1977-1978 President: P. A. von Wielligh. Vice-Presidents: Dr M. G. Atmore and D. A. Viljoen. Honorary Treasurer: J. K. E. Douglas. Immediate Past President, Dr M. D. G. Salamon. Members of Council: J. D. Austin, A. N. Brown, A. A. Hazell, Dr P. R. Jochens, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, J. C. Mostert, H. G. M. Rose, W. T. Ruhmer, A. A. Sealey, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: T. S. Wilmot. Chairman, Orange Free State-Klerksdorp Branch: A. N. Shand. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plowman, Dr R. E. Robinson, P. W. J. van Rensburg. Standing Committee Chairmen: Membership, D. A. Vil¬joen; Technical Programme - Metallurgy, Dr P. R. Jochens ; Technical Programme - Mining, Dr D. K. Krige ; Vacation School - Metallurgy, Prof. R. P. King ; Vacation School - Mining, Dr M. D. G. Salamon; Awards, Dr M. D. G. Salamon; Excursions, Dr M. G. Atmore; Adjudication, Dr M. D. G. Salamon; Consti¬tution, Rules, and Policy, Dr M. D. G. Salamon; Mines and Works, P. A. von Wielligh ; Education, Dr M. D. G. Salamon; Monograph Series, Dr R. E. Robinson; Phoenix National Committee, Dr R. E. Robinson ; Pyrometallurgical Discussion Group Convenor, Dr J. B. See/Dr D. I. Ossin.

Jan 1, 1979

Council and Standing Committees - 1981/82 President: G. Y. Nisbet. Senior Vice-President: Prof. A. N. Brown. Junior Vice-President: Prof. R. P. King. Honorary Treasurer: Prof. D. G. Krige. Immediate Past President: Dr P. R. Joehens. Members of Council: B. C. Alberts, J. D. Austin, P. T. Fewell, C. E. Fivaz, J. J. Geldenhuys, Dr A. K. Haines, P. N. Harris, H. E. James, C. G. Knobbs, Dr B. K. Love¬day, Dr J. Lurie, C. S. MacPhail, D. G. Malan, J. C. Mostert, G. C. Thompson, Dr H. Wagner. Chairman, Witbank/Middelburg Branch: B. Rohrmann. Chairman, Orange Free State/Klerksdorp Branch: K. F. W. Eick. Chairman, Materials Engineering Specialist Division: G. Pienaar. Past Presidents serving on Council: Dr M. G. Atmore, H. Britten, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plewman, Dr R. E. Robinson, Prof. M. D. G. Salamon, P. W. J. van Rensburg, D. A. Viljoen, P. A. von Wielligh. Standing Committee Chairmen: Constitution, Rules and Policy, Dr P. R. Jochens; Membership, Prof. R. P. King; Training, Career Guidance and Education, P. A. von Wielligh; Journal, Prof. A. N. Brown; Monograph Series, D. G. Malan; Technical Programme - Metallurgy, C. E. Fivaz; Technical Programme - Mining, P. N. Harris; SAIMM Schools - Metallurgy, Dr B. K. Loveday; SAIMM Schools - Mining, J. D. Austin; 1982 CMMI Congress, Dr M. G. Atmore; Awards, Dr P. R. Jochens; Adjudication, Dr P. R. Joehens; Phoenix National Committee, Dr M. G. Atmore; Excursions, J. C. Mostert; Mines and Works, Prof. A. N. Brown; World Mining Congress - National Committee, Prof. R. P. Plewman.

Jan 1, 1982