Search Documents

By O. Barron, C. Felix

In 2023, polymer electrolyte membrane fuel cell membrane electrode assemblies accounted for about 62% of the global fuel cell market share and this demand is expected to grow. Commercialisation requires technologies capable of cost-effective, high-volume manufacturing. The membrane electrode assembly is crucial and represents a significant cost to polymer electrolyte membrane fuel cell manufacturing. Manufacturing the electrode components for membrane electrode assemblies at high volumes can reduce production costs while delivering on the forecasted industry demands. Roll-to-roll is a mature coating technology applied in various manufacturing industries such as batteries, printed electronics, microelectronics, photovoltaics, printing, paper consumables, etc., with significant potential for polymer electrolyte membrane fuel cell manufacturing. While the high-volume production process for membrane electrode assembly manufacturing differs from laboratory-scale, the membrane electrode assembly structure remains unchanged. Roll-to-roll is a continuous coating process with speeds of 10 m/min being achieved. In this work, MicrogravureTM and slot-die coating methods have been adopted and have shown promising outcomes for producing gas diffusion electrodes for membrane electrode assemblies. An overview of the MicrogravureTM and slotdie coating methodologies is provided, and a discussion on preliminary results and challenges are presented. Work on MicrogravureTM gas diffusion electrode manufacturing has already achieved comparable performance with spray-coated gas diffusion electrodes. The influence of coating parameters and drying on the coated catalyst layer quality is discussed.

May 27, 2025

By R. Mumbi, M. Peart, E. Arinaitwe, B. Mbao, J. Zulu

Since 1925, xanthates have been widely used in sulfide flotation due to their low cost, ease of manufacture, and ability to float most value species. However, the industry's increasing need for safer and more selective alternatives, driven by low head grades, poor-quality, difficult-to-process ore with complex mineralogy, and stricter environmental regulations, has led to the development of Solvay's AERO® XR series of collectors. These custom-formulated products are based on greener chemistries and offer metallurgical benefits that are similar to or better than those of xanthates, without the safety concerns. Developed through Solvay's Flotation Matrix (FM) 100 approach, the XR series collectors are suitable for a wide range of applications, including the processing of Cu, Zn, and Cu-Ni, as well as the flotation of precious metals. This paper will highlight the differences between xanthates and XR series collectors, and present case studies of their successful commercial application at various global operations.

Jan 1, 2023

Mining executives often have a difficult task determining what the strategic objective of the business should be as this can be impacted by the prevailing market conditions. In addition, they have no mechanism to quantitatively 'test' the impact of this strategic decision on the business and understand the underlying dynamics. During the commodities bull run of 2003 to 2008 the strategic objective may have been to grow the long term value of the business (NPV) through increased tonnage, acquisition and finding new reserves, which all came with an increasing fixed cost base. Now with the financial crisis upon us and the collapse of commodity prices and demand, executives have adjusted their strategies as 'cash is king' and short-term cash flow, in some instances at the expense of long terms value, is the order of the day. For many mining companies, mine closures, reductions in production and cost cutting exercisers are now the focus. In many instances, management do not have an ability to rapidly test different strategic alternatives to 'test' the impact on value, unit costs, reserves and profitability at the operational level and optimize the underlying trade-off variables. Economic modelling of the complete business value chain is a means of linking the operational 'reality' and strategic choices, so that the full impact can be assessed. This paper describes some of the challenges facing mining executives and how economic modelling can be applied to make decision making more rigorous.

Jan 1, 2010

By F. Botha

South Africa is amongst the 40 driest counties in the world, with extreme weather conditions and beset by both droughts and floods. Coupled with economic growth is an increased demand on water resources and, as with all other industrial developments, mining requires large volumes of water, which is likely to have an impact on the environment. Further to this, the mining industry also realizes that minerals are a non-renewable resource and the contribution to wealth creation from mineral extraction is not everlasting. It serves as an economic boost and careful planning is required to ensure that the legacy of mining is sustainable, and that some of the returns from mining provide continual economic and social prosperity.

Jan 1, 2012

By G. P. Dyke

With the removal of the majority of the shallow mineral reserves there has been an increase in the mining depths in the South African mining industry. This has, in turn, changed the industry?s and stakeholders? perceptions of risk associated with mining-induced instability. In recent years the increased mining depth, particularly in open pits, has led to an increase in pit slope failures, which has highlighted the need for appropriate and effective pit slope management programmes. Such a programme comprises many facets, including mine hazard plans, regular slope inspections, cleaning of interim and final pit faces, blasting practices, histories of failures, pit depressurization, stormwater control and evacuation procedures. However, it is arguably in the field of slope monitoring that the most significant strides have been made in terms of new technologies and best practice in open pit mining geotechnics, with the introduction of technologies such as laser scanners and slope stability radar. This paper seeks to illustrate the operational benefits associated with the implementation of new technologies into open pit mining, using AngloGold Ashanti?s Geita Gold Mine in Tanzania as an example.

Jan 1, 2009

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2 (Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ? phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By K. A. du Preez, P. J. van Staden, M. van Rooyen

Mine-impacted water, including acid mine drainage (AMD), is a global problem. While precipitation of dissolved metals and neutralization of acidity from mine-impacted water is accomplished relatively easily with lime addition, removal of sulphate to permissible discharge limits is challenging. This paper presents a high-level comparison of four sulphate removal technologies, namely reverse osmosis, ettringite precipitation, barium carbonate addition, and biological sulphate reduction. Primarily operating costs, based on reagent and utility consumptions, are compared. Each process is shown to be subject to a unique set of constraints which might favour one over another for a specific combination of location and AMD composition. Access to and cost of reagents would be a key cost component to any of the processes studied. The total cost calculated for each process also depends on the type of effluents that are allowed to be discharged.

Oct 1, 2021

By S. J. Baumgartner

The ferromanganese industry is under pressure to deal with the slag arising from the production of ferromanganese, which is discarded in landfills or slag heaps. This material poses an environmental and health risk to surrounding ecosystems and communities, and disposal costs are increasing. Ferromanganese slag contains an appreciable amount of residual manganese metal, which can be exploited. Previous work has shown that the slag can be leached fully, while rejecting the silica to a residue. The methods that were investigated to recover manganese from the leach solution included hydroxide precipitation to upgrade the leach solution followed by manganese carbonate precipitation to produce a pure manganese carbonate product or a manganese carbonate furnace feed material, which would be recycled to increase manganese recoveries in the production of ferromanganese. In addition, electrowinning of electrolytic manganese dioxide from the leach solution was studied. The methods were compared in terms of selectivity, costs, and product quality. Co-recovery of the leach residue, which is a potential cement additive, is discussed. Among the methods investigated to upgrade the pregnant leach solution, hydroxide precipitation utilizing ammonia to adjust the pH appears to be the most effective in removing major impurities such as iron, aluminium, and silica to less than 1 ppm. The manganese carbonate and impure manganese carbonate furnace feed products met quality specifications. However, although the production of these materials was technically viable, the large amounts of base reagent that were required to raise the pH, and the associated high operating costs, rendered the process uneconomic. An optimization study was therefore carried out with the primary objective to determine the ideal acid amount to be utilized in the waterstarved digestion stage, thereby decreasing acid and base consumption while optimizing the quality of the pregnant leach solution, and producing a leach residue that contained <1% Mn. The outcome was an economically viable process. Additional benefits included an increase in the manganese content of the impure manganese carbonate furnace feed material, and a substantial reduction in the dilution of the pregnant leach solution, thereby maintaining high manganese concentrations that rendered the solution viable for electrowinning of electrolytic manganese dioxide, the production of which yielded a current efficiency of 74%.

Jan 1, 2014

By Y. Zhou, G. Chisakuta, P. Bwando, G. Mitshabu

A newly started copper hydrometallurgical plant was confronted with a manganese oxidation issue in electrowinning. This oxidation, in the absence of the amount of iron required to stabilise the electrolyte oxidation-reduction potential, is known to produce oxidants (MnO2, MnO4) that can cause accelerated degradation of the organic phase components in solvent extraction and corrosion of lead anodes in electrowinning. The overpotential required to build up the protection layer on new anodes causes an increased electrolyte potential that creates oxidized species in the electrowinning tankhouse, and these species come back to solventextraction plant with the recycled spent electrolyte. This paper discusses the impacts of manganese oxidants on the health of a plant organic phase. It also outlines the actions taken using iron scraps and sulfur dioxide to mitigate the problem that happened due to the lack of ferrous iron sulfate available on site, as recommended for better control.

Jan 1, 2023

By Q. Cui, B. Z. Zhou, Z. G. Song, Y. G. Zhu, G. B. Zheng

The complex refractory Cu-Pb-Zn polymetallic ore in Xinjiang, China is a massive sulphide ore with complex mineral components. In the past two years, the ore mineralogy has changed, resulting in a decline in metallurgy, with too much zinc reporting to the lead and copper concentrates. A detailed mineralogical study indicating the presence of secondary copper minerals, which could be activating the sphalerite early in the present circuit, was used to develop a novel reagent and flotation flowsheet termed “Pb-Cu co-flotation, Cu intensified flotation, Zn flotation”. It was tested and found to significantly contribute to improving the flotation performance of the ore. In the Pb-Cu co-flotation circuit, successful depression of pyrite and sphalerite was achieved using a BK612- Na2S based depressant system. Most of the galena and some of the Cu bearing minerals with excellent floatability were collected with the use of the selective collector BK906. The rest of Cu bearing minerals were floated in a copper Z200 circuit using a BK537-lime-zinc sulphate based depressant scheme. Zinc flotation from the copper tailing was performed in a SIBX circuit using lime as a pyrite depressant. Using the proposed flowsheet, overall Pb, Cu, and Zn recovery increased significantly to 88%, 87%, and 90% respectively. Keywords: Complex polymetallic ore, Cu-Pb-Zn, Pb-Cu co-flotation, particle size

Jan 1, 2020

By F. Rosenblum, K. E. Water, J. A. Finch, S. Moon, Y. H. Tan

Previous work has shown that sulphide self-heating occurs in three distinct stages referred to as Stage A, Stage B and Stage C. In this paper the focus is on the transition from Stage A to Stage B, which occurs at ca. 100OC. Background literature hints that the transition corresponds to the transformation of the rhombic form of elemental sulphur to the more reactive monoclinic form that occurs at 96OC. A test apparatus is modified for adiabatic heating to track the transition. The results support this transformation of sulphur as being key to the transition, and the transition temperature is thus modified to 96OC. Variations in a sample’s response under adiabatic conditions are observed and possible reasons are discussed. Testing in adiabatic mode provides new insights into the sulphide self-heating process that complement the test designed to identify propensity to self-heat. Keywords: Self-heating; Stage A/Stage B; transition; rhombic/monoclinic elemental sulphur; adiabatic heating

Jan 1, 2020

By P. Pięta, A. Surowiak, T. Niedoba

In a flotation process of copper ore three factors were measured: copper grade in concentrate (β), copper grade in tailings (J) and recovery of copper in concentrate (e). The experiment was conducted by means of the Jameson cell. The factors influencing the quality of the process were particle size (d), time of separation (t), type of the collector (k) and dosage of the collector (s). The considered vector function was then [β(d, t, k, s), J(d, t, k, s), e(d, t, k, s)]. Optimisation achieved was based on determining the values of the adjustable factors (d, t, k, s). The goal was to obtain the highest possible values of functions β and e (maximum) and the lowest possible values of function J (minimum). To this purpose the taxonomic methods were applied. Keywords: Flotation, copper ore, lithology, flotation agents, particle size distribution, taxonomic methods

Jan 1, 2020

By J. Githiria, D. Wachira

The conventional truck and shovel haulage system has become expensive to operate in most mines due to current strict environmental conditions, increase in depth and size of open-pit mines, increase in labour costs, and fuel costs. These factors have motivated the search for alternative material haulage options in open-pit mines. In-pit crushing and conveying (IPCC) system has been regarded as a plausible alternative in material haulage systems. However, usage of IPCC has been limited to a few mines due to limited knowledge of IPCC performance, and other technical factors of the system. This paper investigates, and evaluates the productivity performance of four types of IPCC systems (fixed, semi-fixed, semi-mobile, and fully mobile IPCCs) using mine productivity index (MPi). Using a model developed by MATLAB, the MPi for the four systems is computed using input variables such as availability, utilisation, performance and number of trucks and shovels in a limestone quarry. The mine productivity index for fixed, semi-fixed, semi-mobile, and fully mobile IPCC is obtained as 67.13%, 69.02%, 70.52%, and 71.52% respectively. In conclusion, the fully mobile in-pit crushing and conveying system is the most appropriate IPCC in the quarry, due to its better productivity performance compared to the other three IPCC systems and the truck and shovel system currently in use.

Sep 1, 2021

By G. Chambovet

Applied geophysical methods such as the surface seismic method have been applied for many years and in many places, mainly for oil exploration and to a lesser extent for mineral deposits? exploration in sedimentary basins. The seismic method fundamental is based on the variations of acoustic impedance in a layered earth model and such variations at each main geological interface create reflected waves that are processed and imaged in order to output a clear picture of the subsurface structure. The geology of South Africa was historically, and even until recently, considered as unfit for seismic exploration and the mines were always reluctant to spend any portions of their exploration budgets on these techniques. Hard rocks and high P-waves velocities were creating quite a hopeless model for any mine geologist or geophysicist (if any), unsuitable for the proper use of seismic waves to image their subsurface problems. Boreholes were considered the only reliable tool to derive a geological image of the mine structural features and were linked sometimes with surface methods such as aero-magnetism. The obvious flaw of this methodology was the inability to derive a continuous image from a discrete set of measurement points. Surface 3D seismic is the tool that gives a reliable solution from the initial model extracted from the boreholes, as even the aero-magnetism mapping gives a flat image, unable to show any depth correlation from well to well. The first 3D surface seismic surveys were recorded in the early Nineties only for the gold mines of the Witwatersrand, after a series of serious new shaft sinking failures. The wrong geological locations of these shafts resulted in financial loss of several hundred million rands. The era of3D seismic just started in South Africa and till 1997, all seismic done in the country was for gold exploration with geological target depths close to the oil exploration average depth of investigation. A very important breakthrough was reached when the depth accuracy of the seismic image was tested in real scale as the stopes were surveyed. An error of amplitude of 20 m was usual when true depth was compared with the seismic image predicted depth and shape. This accuracy, completely unknown in oil exploration, started to gain supporters of seismic methods in the mining community but the cash problems and the concentration/disappearance of gold mines in the late Nineties, led to the belief that seismic would be just a very short exploration activity for the mining sector. ort exploration activity for the mining sector. But starting in 1998 with Impala, a tremendous and continuous 3D surface seismic activity occurred in the platinum mining sector. The seismic world got used to new terms such a Merensky and UG2, which have replaced the VCR and black reef. If the primary expectation of platinum surface 3D seismic was to determine and ascertain new shaft locations, as for the gold mines, the quality of seismic data led the mine geologists to require smaller and smaller imaging of geological objects. In addition to the main structural image, small faults, potholes, and shear zone were common expectations of platinum seismic. In a constant velocity environment, what saved the day was the sharp density contrast between the PGM reef and the embedding geology. A good contrast of impedance exists in the whole Bushveld and is sufficient to have enough reflected waves from the PGM main layers to build a high quality seismic image of the subsurface. Recent advances in technology have led in less than 10years to major improvements in the seismic acquisition by using high frequency vibrating seismic sources, but also in processing and interpretation. With these latest improvements, seismic can detect objects of 7.5 m size, either fault throws, flexures, etc. The PGM formations of the Eastern limb of the Bushveld Complex are now accessible for seismic imaging, with cost per square kilometre comparable to the borehole cost of the same surface unit. The economically acceptable seismic surveys can be used for UG2 structural imaging up to a depth of 210 m below surface. Linked with borehole information, 3D seismic today offers a wide range of information for mine development: structural imaging, small fault detection, pothole and shear zone identification. All users of 3D seismic have also used this technique as a tool in the process to qualify their mineral reserves and especially from the category ?inferred? to the category ?measured?. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. Junior mining companies, in the feasibility stage of their projects, are also quite eager to use seismic as a reserve certification tool, when they present financial statements to future potential investors. The current high demand on platinum, pushes the seismic towards new technologies to be implemented in order to improve the final image. Using surface and borehole seismic together or acquiring seismic surveys with multi-component receivers have been just introduced in South Africa. In less than 10 years, surface seismic by adapting its methods to the special case of the Bushveld, became a mandatory step in mine development and ore resources evaluation. As part of the ?seismic? world we are proud to be a major player the ?surge? of platinum exploration and production in these last years and we will certainly increase our synergy with the mine sectors in the exciting coming years.

Jan 1, 2006

By J. L. Havenga, L. J. van der Walt, J. T. Nel, H. Bissett

"SynopsisNew technologies used to manufacture high-quality components, such as direct laser sintering, require spherical powders of a narrow particle size distribution as this affects the packing density and sintering mechanism. The powder also has to be chemically pure as impurities such as H, O, C, N, and S causes brittleness, influence metal properties such as tensile strength, hardness, and ductility, and also increase surface tension during processing.Two new metal powder processes have been developed over the past few years. Necsa produces zirconium powders via a plasma process for use in the nuclear industry, and the CSIR produces titanium particles for use in the aerospace industry.Spheroidization and densification of these metal powders require remelting of irregular shaped particles at high temperature and solidifying the resulting droplets by rapid quenching. Spherical metal powders can be obtained by various energy-intensive methods such as atomization of molten metal at high temperatures or rotating electrode methods. Rapid heating and cooling, which prevents contamination of the powder by impurities, is, however, difficult when using these methods for highmelting- point metals. For this reason plasma methods should be considered.Thermal plasmas, characterized by their extremely high temperatures (3000–10 000 K) and rapid heating and cooling rates (approx. 106 K/s) under oxidizing, reducing, or inert conditions, are suitable for spheroidization of metal powders with relatively high melting points. Thermal plasmas for this purpose can be produced by direct current (DC) plasma arc torches or radio frequency (RF) inductively coupled discharges. In order to obtain chemically pure spheroidized powder, plasma gases such as N2, H2, O2, and CH4 cannot be considered, while Ar, Ne, and He are suitable. Neon is, however, expensive, while helium ionizes easily and it is therefore difficult to obtain a thermal helium plasma at temperatures higher than 3000 K. Therefore argon should be used as plasma gas. Residence times of particles in the plasma region range from 5–20 ms, but this is usually sufficient as 7–8 ms is required for heating and melting of titanium or zirconium metal particles in the 30 µm size range at 3500 K. In this study the melting and spheriodization of titanium powders was investigated by DC non-transferred arc and RF induction plasma methods. The powders were characterized before and after plasma treatment by optical microscopy and scanning electron microscopy (SEM) to observe if any melting or spheroidization had occurred."

Jan 1, 2015

By Stuart Marsland

"Reference materials have always been important for validating and controlling analytical methods&apos;, They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry demand critical validation of all results reported. Mintek has been producing geological and semi processed ore references since the early 1970&apos;s and recently due to increase in demand other manufactures have entered the South African Market.This paper describes Analytical challenges from the customer&apos;s perspective. The customer being the metallurgist, mine geologist, environmental scientist and geologists from resource companies. Reference Materials and their appropriate use and good understanding of them can aid greatly in building confidence in the results, choosing the right Laboratory for a project, deciding which set of results arc correct and providing evidence to the customer&apos;s clients that the results obtained are the very best possible.Throughout the world there are hundreds of reference materials produced by over 80 organisations and these are mainly ores, rocks, semi processed ores, metals, and many more. Mintek is one of the top 10 producers with over 75 products. Many of these producers including Mintek and their respective standards organisations belong to the ISO REMCO committee and their respective work groups. This committee&apos;s main task is to draw up guide lines for the use, manufacturing and certifying reference materials. In South Africa a mirror committee has recently had its inaugural meeting the function is to give clear mandate to the South African representative on the main ISO REMCO committee, the South African delegate bas an opportunity to influence the contents of the guides.Tile SARM program has since the year 2000 increased its sale three fold, the question is why? There is more accountability needed in our world. That means Analytical results have to be the very best possible and risks associated to them must be well quantified. Consider that the risk of wrong results of wrong decisions made from a result is trivial to laboratory, in comparison to the laboratories customers. The consequence to a laboratory could be a loss of income or some one may lose their job. To the customer he may dig up 1000 of ton&apos;s of rock with nothing in it or worse still don&apos;t mine it when the grade is high enough. This is seriol1s money."

Jan 1, 2014

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By D. Weijie, S. Kai, Y. Hu, X. Ning, M. Shiyi, W. Junpeng, Z. Guihong, L. Xianjie

Flotation is one of the most important processes in the copper production industry. The copper grade in the concentrate is a pivotal indicator of the flotation process performance. However, it is difficult to achieve real-time measurement through hardware sensors. Based on the production data provided by an industrial operation, a novel soft sensor based on multi-layer perceptron (MLP) is proposed for effective monitoring of this pivotal indicator. The proposed soft sensor uses the nonnegative garrote (NNG) to perform global variable selection for MLP, while a local search (LS) approach is incorporated to improve the model presented by NNG. Simulation results show that the proposed algorithm has higher prediction accuracy and better model simplicity than other algorithms. Furthermore, the variables selected are consistent with the field experience, and the developed model can provide reference of feedback control for the optimisation of the process. Keywords: Flotation process of copper ore, nonnegative garrote, local search, soft sensor, multi-layer perceptron

Jan 1, 2020

By L. Petzold

The demand for stainless steel is ever-increasing. As an essential element in stainless steel-making process, so is the demand of chromite concentrate. At the same time, the industry proven technologies for beneficiation of chromite are limited. Chromite is only crushed, screened and jigged to produce a concentrate. However, for ultrafine and low-grade material, no satisfactory beneficiation methods for the enrichment of chromite fines exist in industrial operation. This poses a clear challenge for the industry, which Primetals Technologies has addressed with the development of a new beneficiation process. The aim of this process was to enrich low grade chromite tailings to a quality suitable for the smelting process. Required concentrate grades are different over the world, concentrate grades of Cr2O3=40% and lower are found at the Bushveld Complex, South Africa. The target for the present study was a Cr2O3-grade in the area of 49%. Three different chromite tailings with Cr2O3 grades between 16 % and 29 % were part of a study, executed by Primetals Technologies. All three tailing materials were characterised by Mineral Liberation Analysis (MLA). Based on the physical, chemical and mineralogical findings, process flowsheets were developed. The process flowsheets included grinding to ensure a full liberation of the chromite. The liberated material was classified at a cut size of 63 μm to a coarse and fine fraction. Gravity separation and flotation processes were tested with the coarse particle fraction. Due to the limitations of gravity separation with fine particles, only the flotation process is suitable and was tested with the fine fraction < 63 μm. A Design of Experiment (DoE) with six factors, each three levels, was conducted to identify optimal parameters for the fine chromite flotation. Two different collectors were tested: a phosphoric acid ester and a fatty acid type collector. In small scale test work a chromite concentration suitable for the smelting process was achieved. On this basis Primetals Technologies will develop a pilot-scale test program to research recirculation effects and upscale potential of the process. Keywords: Mineral processing, tailings beneficiation, flotation, density separation, process development, chromite

Jan 1, 2020

By J. N. Baloyi

"In atomic emission and atomic absorption spectrophotometry, the sample is heated to a high temperature and thereby decomposed into atoms and ions that absorb or emit visible or ultraviolet electromagnetic radiation at energies characteristic of the elements involved. The flame test is a very simple form of this technique. The yellowing of a flame by the addition of salt, for example, occurs because the sodium in salt emits strongly in the yellow portion of the visible spectrum. These methods are especially useful for low concentrations of metallic elements in both qualitative and quantitative analysis.Interference on Iep-OES has not always been considered a serious problem, especially in the beginning, when compared with Atomic Absorption Spectroscopy. This was due to the euphoria created by the new technique. It meant that criticism was subdued. The Iep was vastly superior to the Atomic Absorption technique, that the interferences suffered by the Atomic Absorption technique dwarfed the little interferences suffered by the rep-OES technique. This is how rep-OES has had a reputation as an interference free technique."

Jan 1, 2014