Search Documents

By W. H. Eddy

Laboratory batch and small-scale continuous flotation tests were con-ducted by the Bureau of Mines on a mica waste tailing from Kings Mountain, N.C., to determine the feasibility of producing high-quality mica, feldspar, and glass sand. Mica was recovered by two methods; one was by flotation in an alkaline circuit, which produced a mica concentrate assaying 92.0 percent mica with a recovery of 87.l percent, and the other by flotation in an acid circuit, which produced a mica concentrate assaying 91.0 percent mica with a recovery of 79.4 percent. Continuous flotation processing yielded a feldspar concentrate assaying 1.10 percent Na20 and 13.50 percent K20, with recoveries of 66.4 and 80.6 percent, respectively. The feldspar tailing was high-quality quartz glass sand analyzing 98.6 percent Si02 and 0.02 percent Fe203.

Jan 1, 1969

By Robert F. Chaiken

A quasi-steady-burning channel model is used in this Bureau of Mines study to describe the conductive heat loss from an in situ coal combustor to the surrounding rock strata. The calculated heat losses are significantly greater than those previously estimated, but are still very acceptable from the viewpoint of energy recovery. Approximately 80% to 90% of the heat of combustion of the coal should appear as sensible heat of the gaseous exhaust, with exhaust temperatures in the range of 1,000° to 1,200° C. The effects of burning stoichiometry and channel size on the heat loss are also discussed in terms of the model. Such effects are shown to be compatible with an in situ combustion process even in thin seams. However, these results depend on gas leakage and adverse roof falls not being important factors in deter-mining the heat loss mechanism.

Jan 1, 1977

To improve the efficiency and speed of under-ground post-disaster rescue operations. The Approach: Develop a battery-powered mine-rescue vehicle designed to carry rescue crews, rescued miners, and their support equipment. How It Works: The experimental vehicle, shown below, was designed and constructed by the Mine Safety Appliances Company under contract to the Bureau of Mines. ATV Manufacturing Company and Delco Electronics were subcontractors. A rechargeable, silver-zinc battery provides power to a 3-horsepower permissible motor, the speed of which is regulated by a solid-state controller. Three wheels on each side are independently driven by a chain and mechanical trans-mission.

Jan 1, 1974

By Fred N. Kissell, Maurice Deul, T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979

By G. S. Scott

The flammability of trichloroethylene vapors in air has been determined in a 7-inch cyclindrical vessel. Saturated flammable mixtures were formed with air at atmospheric pressure between 30° C (86° F) and 82° C (180° F); the trichloroethylene concentrations at these temperatures are 12.5 (lower) and 90 (upper) volume-percent, respectively. Further study is necessary to assess the effects of different variables on the flammability of this material. INTRODUCTION Trichloroethylene (TCE) (ClHC = CCl2), sold under various trade names (Blacosolv, Perm-A-Clor, Tri, Triad, Triclene, Trivec, Tromex, Vapoclean, Vapoclor, Westrosol, etc.), is an important industrial chemical. A summary of its physical and chemical properties is given in table 1. It is used to degrease metals, leather, and textiles, to extract residual oils from vegetable oil cakes, for dry cleaning, and in soap. It is a powerful solvent for fats, resins, bitumens, rubber, sulfur, and phosphorus. Several explosions in which trichloroethylene was involved prompted an investigation by the Bureau of Mines to determine the conditions under which such accidents can occur.

Jan 1, 1963

By F. C. Trutt, J. Sottile, J. L. Kohler

Presented in this paper is a theoretical review of the relationships that should exist between electrical winding parameters and the mechanical vibration of a-c machine elements under normal and faulted operating conditions. Also included is data from an experimental study that relates stator vibration and bearing vibration to selected winding faults in a synchronous machine. Consideration of these results indicates a significant relationship between electrical deterioration and mechanical vibration and thus provides the motivation for additional study and a basis for future applications.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 6 Automatic Elevator Control Systems An automatic elevator control system, consisting of position sensing devices and a control unit, can be used to control an emergency mine hoist. While automatic elevator control systems are assembled from standard components, they are typically custom designed to suit a given customer's application. Various manufacturers contacted indicated that the price range, less installation, for a simple two-stop control system begins at approximately $2500 and can increase depending upon the type of components used, shaft depth, the type of mechanical drive used, and the maximum operating speed A partial list of elevator control manufacturers follows. They should be contacted for further details. Marshall Elevator Company Pittsburgh, P A 412 -431 -1340 Armor Elevator Company, Inc. Louisville, KY 502-361 -7181

Jan 1, 1976

By B. T. Brady

Results of a study are presented of the effect of low radial reinforcement pressure on the postfailure characteristics of two types of granite, a sandstone, and marble. The low radial reinforcement pressure is applied to the rock surface by a gooch rubber sleeve. The gooch rubber sleeve provides a radial pressure of less than 1 psi pressure to the rock surface. This method of support gives an average strength increase of approximately 8 percent to the fractured rock sample.

Jan 1, 1973

By H. S. Hardman, G. T. Adams, Will H. Goghill

"Usually a newly developed machine leaves the factory ""on a wing and a prayer."" The manufacturer hopes that the operator will hasten to report defects. In turn, when the suggestions arrive the manufacturer makes the required changes and maintains close collaboration with the operator. Thus the history of our machines of today is written.Laboratory concentration tables are exceptions to growth by experiment and collaboration. Their operation never enters directly into the cost sheet; they are seldom used for longer periods than 10 minutes; and the experimenter, while hurrying to another job, accepts the table, good or bad, for a quick test on his ore. Thus we go back about 50 years when we use the preset in factory-built laboratory table.The Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, recognized the existence of a tabling problem net usually considered. That is, instead of using the table to test the ore, the ore was used to test the table. In this critical examination of laboratory table six defects were encountered (and remedied). They are:"

Oct 1, 1945

By J. L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former US Bureau of Mines (USBM) to engineer techniques that will reduce the hazards in the mining workplace associated with coal bumps. Recent research focused on a longwall coal mine in Utah with overburden greater than 750 m (2,500 ft) containing several massive sandstone units. The primary field instrumentation at the site was three-dimensional, full waveform, autonomous microseismic arrays placed underground and on the surface in order to surround the active multi-panel longwall district. The purpose of these arrays was to help investigate the strata mechanics associated with the redistribution of stress and the associated gob formation of the longwall. Specifically, the seismic arrays were used to determine the timing and location of the failure in the strata surrounding the active mining. Overall 13,000 seismic events were detected and located with on-site processing during the five months the panel was being mined, including a magnitude (ML) 4.2 event. Of these, a smaller subset of 5,000 well-located events was selected during post-processing to form a consistent data set for analysis in this paper. From this data set, it was observed that the seismic events generally occurred in advance of the longwall face, both above and below the panel, consistent with failure of the strata in the forward stress abutment zone. Also, the occurrence of the ML 4.2 seismic event within 150-180 m (500-600 ft) of a deep cover longwall face with no associated bump caused a re-evaluation of the nature of the connection between seismic activity and coal bumps.

Jan 1, 2002

By Charles L. Kimbell

This study is intended to serve three roles. First, it represents a global overview and summary to supplement and complement the five regional companion volumes of the 1991 edition of the Minerals Yearbook International Review. In this regard, it also extends previous time series under this title that appeared as the introductory chapter to the international volume of the Minerals Yearbook from the inception of that volume in 1963 until it was subdivided into separate regional volumes in 1989. The basic statistical presentations herein generally contain data through and including that for 1991, although in a few instances the most recent statistics are those for earlier years because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting the world's mineral industry that have occurred between the end of 1991 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By R. V. Ramani, P. M. T. White, D. Sutton

5.1 Incorporation with the Master Design Simulator Figure 1 diagrammatically illustrates the interaction between the various sub-systems that go to make up the total Master Design Simulator. As a total system, all sub-systems will be scheduled as needed by the controlling program. The data require¬ments for each will be made available either by providing common storage in core or by outputting data to external storage devices such as magnetic tape, disk, drum, etc. The incorporation of the Geology and Reserves sub-system into the total system involves the establishment of an interface through which data may be readily dissemminated in either direction. This interface will be provided by a geological data library in which all information available from the sub-system is stored and can be readily accessed by the main program and/or other sub-systems. In Figure 7, the information flow between the Geology and Reserves sub¬system and other sub-systems is shown. 5.2 Independent Function Geology and Reserves sub-system is capable of functioning as an independent unit or in direct communication with another sub¬system. This is possible by either continued use of the data library or by redirecting output to other peripheral devices separate from the total system libraries. (Figure 8).

Jan 1, 1974

By S. H. Katz

Artisans and laborers in mineral industries where the air is dusty with particles of reel: are subject to a peculiar pulmonary disease known as miners' phthisis or stone cutters' consumption. In granite cutters the disease is specifically designated as granite pneumoconiosis. Very fine particles of the harder rocks are especially injurious when inhaled into the lungs. It is estimated particles about one micron (1/23000 part of an inch in diameter) are most injurious, because larger particles are more readily removed by the cilia and,wet surfaces of the respiratory passages before reaching the lungs, while smaller particles either do not readily lodge or are more easily eliminated. Silica, of which quartz and flint are composed, and which forms a large part of granite, is one of the hardest of the common rock-forming materials. It is also very insoluble when silica lodges in the lungs elimination is difficult. Rock constituents of granite other than silica are probably injurious but in a lesser degree, and this is also probably true of limestone and the softer rocks. Ultimately a worker who daily inhales much granite dust has considerable deposited in his lungs. If he continues at his trade the lung tissue becomes harder and less elastic, he finds himself short winded, and in extreme cases death may come either directly or indirectly as a result of lung failure.

Feb 1, 1921

Determine the site specific flow behavior of leachants and groundwater during development, production, and restoration phases of an in situ leaching operation. Approach A computer program has been developed which simulates the hydrologic activity associated with in situ mining. Various user options enable modeling of many of the site specific geologic conditions and well field specifications that affect the hydrology of solution mining. How It Works In situ hydrology is modeled, using a closed-form solution to the three-dimensional, partial differential equation that describes changes in hydraulic head as a result of pumping from leachant Injection and recovery wells. Model capabilities include arbitrary well patterns and pumping schedules, partially penetrating well screens, directionally anisotropic permeability and natural groundwater flow, in either

Jan 1, 1981

Lower the respirable dust exposure of longwall shearer operators with improved water spray systems on the shearer. Approach Orient sprays (rather than relocate them) so that dust is held against the face. How It Works Research by the Bureau has indicated that shearer operator dust levels depend largely on how fast dust from the upwind drum spreads into the walkway. Water sprays on the shearer body can greatly affect the spreading of this dust because each spray moves air like a small fan, generating strong cross-currents of air around the shearer. Poorly designed spray systems, especially those with nozzles pointing upwind, will stir up much more dust than they sup-press. On the other hand, Improved systems may be designed to hold the dust cloud against the face while also suppressing It. In such arrangements the water is sprayed downwind and used with screens made from conveyor belting.

Jan 1, 1981

By R. R. Sayers

Carbon monoxide poisoning is one of the most widely distributed and most frequent causes of industrial accidents . Carbon monoxide gas is a product of incomplete combustion , and since it is without color , odor , or taste , its presence is frequently unsuspected in many places where it exists . It is an ever present danger about blast and coke furnaces , smelters , and foundries . It may be found in buildings having a leaky furnace or chimney , and in buildings where a gas stove is used without a proper flue connection , such as is often found in tenements , tailor shops , and boarding houses . Hospitals receive annually a great number of victims of poisoning , either by accident or in an attempt at suicide , from artificial illuminating gas . People may be affected by leaks wherever water gas is formed or used . The exhaust gases from gasoline motors under average running conditions usually contain 5 to 7 per cent carbon monoxide , and sometimes as much as 13 per cent ; deaths from running an automobile engine in a closed garage are not infrequent . A similar danger may arise in operating gasoline engines in launches without sufficient ventilation . The gas is formed also in stoker rooms , in gun turrets on battleships , in petroleum refineries , and by the Lablanc soda process in cement and brick plants . In underground mines carbon monoxide may appear as the result of shot firing , mine explosions , or mine fires , and in tunnels where automobiles , coal or oil - burning locomotives are operated . In spite of the common occurrence of carbon monoxide poisoning there appears to be no uniformly recognized treatment for a person overcome by carbon monoxide . In the rescue work of the United States Bureau of Mines , however , a method has been developed which has been supported by laboratory investigation , and has proved successful in practical experience , over a period of years . As outlined in this article , the method is useful in the hands of first -aid men as well as physicians .

Dec 1, 1921

By M. H. Stanczyk

Bench-scale laboratory tests were made by the Bureau of Mines of a segregation-flotation concentrate, assaying 20.43 percent copper, to investigate the influence of various ratios and concentrations of ammonia and carbon dioxide on copper extraction. Leaching the concentrate with a solution containing 900 pounds of ammonia and 360 pounds of carbon dioxide per ton of feed, followed by washing the leach residue with 1.75 tons of a 10-percent solution of ammonium carbonate and about 1 ton of water (as steam) per ton of solids, resulted in a copper recovery of 96.3 percent. Resegregation and flotation tests of the washed residues revealed that 85 percent of the copper in the residue could be recovered. Steam distillation tests of a typical ammoniacal leach liquor, assaying 39 grams copper, 105 grams ammonia, and 77 grams carbon dioxide per liter, recovered over 99 percent of the copper as a mixed oxide-carbonate precipitate. The ammonia losses in leaching, filtering, washing, and distillation were 0.12 pound per pound of copper recovered in the precipitate. Calcination and subsequent hydrogen reduction of the precipitate yielded a metallic copper powder assaying 98 percent Cu, 0.87 percent Si02, 0.10 percent MgO, 0.54 percent CaO, and 0.41 percent R203.

Jan 1, 1961