Search Documents

By C. W. Davis

"A copper-palladium-gold-silver ore is being mined at Salt Chuck, Prince of Wales Island, Alaska, from which a concentrate is produced that contains 40 to 50 per cent copper, and considerable amounts of palladium, gold and silver. There has been much difficulty in obtaining assays for palladium, gold and silver from the mine, smelter, sampler, and umpire that check within reasonable limits. While the results for copper content have not been unusual, the results for palladium have varied as much as 0c8 oz. on 3 oz. material, results for gold differed by 0.1 oz. on 1.6 oz. materials, and for a silver content of 7 oz., results differed by as much as 4.0 oz.The Bureau of Mines was requested to determine the causes of variation in the results of the different assayers, and to develop a satisfactory procedure for analyzing such ore.Three samples of concentrate were received for analysis, two small lots that had previously been assayed by the various laboratories, and one large sample. The large sample was dried and ground in a ball mill, put through a 150-mesh screen, and then returned to the ball mill for thorough mixing. The small samples were ground to pass a 150-mesh screen and then mixed on a mixing wheel.The large sample (No. 1) was analyzed by five different procedures, one of the small samples (No.2) by three procedures, and the other (No. 3) by two procedures (the two small samples being too small for further tests). The different procedures tried and the results obtained arc presented below. The samples of concentrate were from ore mimed and milled by the Alaska palladium Co. at Salt Chuck."

Feb 1, 1926

By Paul T. Allsman

This paper gives the cost and describes the mining of 55 tons of nickel-bearing rock by hand methods from a prospect in southern Nevada, June 15, 1937, by the Mining Division of the Bureau of Mines. The geology, mineralogy, and problems related to future development also are discussed briefly. The main object was to obtain a 55-ton sample within the limited period during which funds were available; little time was available to make a first-hand detailed study of the possibility of commercial ore deposits being found. The sample was desired by the Metallurgical Division of the Bureau for experimental purposes at the Electro-Metallurgical Station at Boulder City, Nev. The term "ore" is used loosely in the following discussion to designate dike material containing nickel and copper, without consideration of its commercial value. ACKNOLEDGMENTS Material concerning the geology and mineralogy of the prospect and district as obtained from Geological Survey publications by Bancroft3/and Longwell4/.

Jan 1, 1938

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (T.G. Soda Ash, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gages to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gages were 12.5 mm long and embedded into a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gage locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

By H. C. Miller

[California's sensational rise to supremacy as an oil-producing State in 1923 was accompanied by a loss of 62 lives. These 62 deaths were from oil-producing accidents alone and do not include fatalities at the refineries, on tankers, or on any work not directly connected with the drilling for and the production of oil. The number of facilities for 1923 was 82 per cent greater than in 1922, the next most fatal year, with a record of 34 lives lost. The data submitted in Table 1 show that for the calendar years 1917 to 1923 inclusive, an average of 4.74 million barrels of oil were produced per Vitality in the California oil fields. On this basis, the record for 1923, hough a trifle below the average, shove up slightly better than that for 1922.]

Jan 1, 1924

Roof bolting is a slow, expensive, and absolutely necessary mining activity. Roof-bolting activities also account for the largest percentage of lost-time injuries in underground coal mines. Dull bits result in the application of excessive force, which bends drill steel; and changing starter and finisher steel was the most significant source of injuries associated with roof bolting. The tungsten carbide (WC) roof-bolt drill bits currently used in American, Canadian, and Australian coal mines are capable of drilling only one or two 4-ft holes and then they are resharpened once or twice to drill another one or two holes. Often, in medium-hard rock formations (sandstone), as many as 20 to 30 bits may be required to drill a single 4-ft hole. Objective To compare the performance, longevity, and cost of newly developed polycrystalline diamond compact (PDC) roof-bolt drill bits against WC bits. Research and Background Diamonds for industrial use have been scarce throughout history and continuous attempts have been made to produce synthetic diamonds. The first synthetic diamonds were manufactured in 1953. Economically produced synthetic diamonds are 1 to 10 µm in size, but in this size range, they are totally unsuitable for industrial applications. In 1972, General Electric Co. developed a process to sinter the artificially developed, minuscule diamond particles into usable products. In this process, several layers of diamond-particles-and cobalt mixture are overlaid on WC substrates and sintered at 2,350° F and 1,000,000 psi. The final product is known as PDC. Today, PDC's are available in many shapes, but their size is limited to 3/4 in, or less, in length or diameter, because pressures greater than 1,000,000 psi are required to manufacture larger PDC's. At present, diamond and PDC arc the hardest and strongest commercial materials available for wear surfaces. The PDC used in this study had a hardness 3.61 times greater than that of WC.

Jan 1, 1992

By Henry M. Harris

The Bureau of Mines investigated a glass containing approximately 17 percent lithia and 83 percent silica to establish a method of devitrifying cast and rolled shapes. Glass shapes with high strength were made by melting, forming, and rapid cooling of the composition, and the shapes subsequently were converted to a crystalline condition by heat treatment. The best devitrification schedule included rapid cooling of the glass to below 300° C, followed by reheating at a rate of 50° to 400° C per hour, depending on the size of the shape, followed by a of 60 to 70 hours at 500° C and another period of 15 hours at 800° C. attempts to use faster heating rates or slow cooling to accomplish devitrification in deformation of the shapes. The crystalline shapes had flexural strengths that averaged over 33,000 psi, achieved with an annealing time of 60 to 70 hours at 500° C.

Jan 1, 1965

By E. D. Gardner

"The Bureau of Mines has studied blasting practices in metal mines of the Southwest. The investigation of blasting drift rounds showed among other results, that cut-holes in ground difficult to break could be chambered to advantage under some conditions.In open--cut mines, chambering nearly all holes before blasting is the common practice. Two or more free faces are generally maintained in this type of work, and the amount of explosive necessary to break any bench or bank can usually be estimated from the yardage to be moved. However, in blasting drift or tunnel rounds only one free face is available before the cut-holes are shot, and the quantity of explosive required is generally ascertained best by trial.In addition to being the most difficult to break, the cut-holes are the most important of a drift round. When the cut-holes ""break bottom"" less work is required of the other holes, and a full break of the round is generally obtained. In ground difficult to blast, extra care and expense are justified to insure that the cut-holes ""break bottom.""At many mines the work is so organized that all blasting is done at the end of the shift, and a decided advantage would have to be gained to make chambering of the cut-holes economical. Also, in many mines blasting during the shift would not be practical. One or two holes could probably be drilled during the time necessary to do the chambering. However, under certain special conditions, such as in small operations or those where ""leasers"" or contractors are working, drill holes could be chambered should there be an advantage in doing so. Moreover, in some mines it might be practical to chamber the cut-holes at the lunch hour. In ordinary rounds the cut-holes are generally drilled by noon. It would not be necessary to tear down the drill or remove tools from the face to do this work of chambering."

Feb 1, 1928

By A. Wahab Khair

"Geologic materials emit transient noises when stressed /1/. The rate and pattern of these transient noises or acoustic emissions (A.E. hereafter) depend on the stages of deformation of the material /2/. It has been demonstrated that rock/coal fracture processes under stress consist of three distinctive stages--crack initiation, propagation and ultimate fracture--and that coalescence of numerous cracks leads to ultimate failure rather than the propagation of a single crack /2,3/. This paper presents an analysis of fracture formation in rock/coal specimens subjected to straight wedge indentors using A.E. technique.The effect of specimen geometry, wedge indentor angle, confining pressure, and material anisotropy on fracture type (tension, extension, and shear crack), fracture length, and fracture intensity were studied. Two types of material mainly Berea sandstone and Coal Berg No. 2 coal were used in this study. Prior to the experiment the mechanical properties of both sandstone and coal were determined using rectangular specimen (Figures 1 a) in standard compression tests and are given in Table 1. In this study cylindrical and rectangular specimens were first prepared to proper dimensions of 2 in. x 1.5 in. and 3 in. x 1.5 in. x 1.5 in. (5.08 cm x 3.81 cm and 7.62 cm x 3.81 cm x 3.81 cm), respectively and then instrumented with SR-4 strain gages as shown in Figure 1. The instrumented specimens were then tested under four distinct load boundary conditions as illustrated in Figure 2. During a typical experiment the instrumented specimen was placed in a specially designed loading jig (Figure 3) where a predetermined lateral pressure was applied mechanically to the specimen by adjusting the inner plate of the confining chamber via screw while monitoring strains in the specimen. Using rock/coal elastic constants and measured strains, a predeter¬mined lateral pressure was applied to the specimen. Then a vertical load was applied by the straight edge of a wedge indentor attached to the upper platen of the universal loading machine via ball and socket arrangement (Figure 4). The arrangement allowed uniform application of load in a straight line manner on the surface of the specimen. During the test a number of parameters namely strains, load and A.E. rates were recorded (Figures 5a-b)."

Jun 1, 1988

By Doris M. Hyde

The impact of mining activities on the economy in both 1983 and 1984 was minimal. The most recent available data on the gross domestic product (GDP) indicated a level of $1.6 billion in 1983.2 The estimated value for the production of cement, aragonite, and salt was about $17 million in that year, down from the estimated $20 million in 1982. No data are available on the economic impact of the large petroleum refinery at Freeport on Grand Bahama Island, but it represents the major mineral-related activity. Cement production remained at only a fraction of the 800,000 tons per year of plant capacity. The offshore search for hydrocarbons continued in 1984, and some companies were about to enter the third year of seismic and geological surveying around Andros and Grand Bahamas Islands. Getty Oil (Bahamas) Co. Inc.; Breoco Ltd., a subsidiary of REO Development Corp. of Tulsa, Oklahoma; and Natomas Petroleum (Bahamas) Ltd. were the first companies to be awarded exploration licenses. These companies were committed to drilling at least one well before the end of the third exploration year. Other companies actively engaged in exploration included Exxon Corp., Atlantic Richfield Co. (ARCO), Chevron Oil Bahamas Ltd., and Esso Oil Bahamas Ltd. Geophysical Services Inc. (GSI) of Dallas, Texas, and Petroleum Services (Bahamas) Ltd. of Englewood, Colorado, ran another seismic survey line during 1984. This 1,533-mile line was in the Great Bahama Bank and Cay Sal Bank areas off the southeast Florida coast, and tied in with a 4,530-mile program GSI ran in 1981-82. These surveys were nonexclusive and publicly available through GSI.

Jan 1, 1986

By James H. Russell

Several solid sorbents were compared for their effectiveness in removing sulfur dioxide from flue gases. The materials were tested for the rate of sorption and capacity at about 300° C, and rate of regeneration around 700° C in thin beds and in 4-inch-diameter fluidized beds. Rates of material loss were also estimated. The sorbents tested included three samples of alkalized alumina, two samples of sodium carbonate-impregnated alumina, and one proprietary sample of porous silica impregnated with copper and iron compounds. The results showed that all the alkalized aluminas had good sorption capacities and rates, required high temperature regeneration, and suffered excessive material loss; the sodium carbonate-impregnated aluminas (1) had high sorption rates but barely adequate capacities, (2) required high temperature regeneration, and (3) suffered excessive material losses; and the copper-iron impregnated silica suffered only slight material loss and could be regenerated at a relatively low temperature, but the sorption rate and capacity were too small. None of the sorbents met all the arbitrary performance criteria that follow: sorption rate constant of 1 min-1, sorption capacity of 0.1 g sulfur per g sorbent, regeneration rate constant of about 0.075 min-1 at a reasonable temperature, less than 0.07 pct per hour material loss during operation, and a chemical life of 500 cycles.

Jan 1, 1971

By James P. Ulery

A Bureau of Mines geologic study of Pennsylvanian and Permian coalbeds in southwestern Pennsylvania was undertaken to determine the effects of coalbed geology and petrology on in situ coalbed gas contents. Data were obtained from 18 coreholes from parts of four 7.5 ' quadrangles in southwestern Washington and northwestern Greene Counties, and from a single corehole in Westmoreland County. A total of 88 samples from 24 coalbeds were collected for direct-method testing to determine gas content. The samples were also analyzed for petrographic composition, chemical composition, and vitrinite reflectance values. Corehole information was used to generate isopach maps and geologic cross sections useful in data interpretation. Results of the investigation show that coalbed gas content is related to vitrinite reflectance, but not to petrographic composition. Gas contents are also influenced by other geologic factors such as roof rock lithology and competency, and location with respect to local fold structure.

Jan 1, 1989

By Foster Fraas

A method is presented for the linear evaluation of adsorption data using the equations dC = Ae-rv dv and v = [jT] - q, where dC is the phase composition increment, v a calculated parameter, T the absolute temperature, and A, r, h, g, and q the constants. The value of v is calculated from the composition C for both the adsorption surface and the immersion phase. A plot of v for each phase on Cartesian coordinates results in straight line graphs. With temperature variation, a plot of v versus,[ ] also results in straight line graphs. The equations are applicable to electronic and salt equilibria.

Jan 1, 1962

By M. L. Whisman

The Bureau of Mines developed a radiotracer method for detecting the contribution of selected components and additives to thermally induce deposits of turbine aircraft fuels. Fuels were examined before and after 52 weeks of storage at 130° F. Of particular concern was the influence of aromatic hydrocarbon fuel constituents on thermal-stability quality of jet fuels during storage. A microfuel coker test apparatus was used to thermally stress the test fuels and blends, and the resultant contribution to deposits of selected fuel components, labeled with carbon-14, was determined by radioactive-counting techniques. Ninety-one blends of five test fuels with carbon-14-labeled fuel additives or components were prepared, tested, stored for 52 weeks at 130° F, and reanalyzed for deposit-forming tendency. These additives included two anti-oxidants, a metal deactivator, and a corrosion inhibitor. Of the labeled hydrocarbon fuel systems studied, the greatest reaction was observed in blends containing methyl-and ethyl-substituted indenes. Other aromatic types also showed some contribution to the deposits. Three of the additives showed a marked tendency to degrade and react during storage and thermal stress. A cresol antioxidant, however, barely contributed to deposit formation. Oleic acid interacted with cadmium present in aircraft fuel systems and produced deleterious effects upon the thermal-stability quality of the fuel.

Jan 1, 1971

By C. P. Mangelsdorf

This report deals with the efforts to develop a portable device suitable for underground use for the purpose of measuring the frequency of vibration of the horizontal chords of Birmingham roof trusses. Four devices are investigated and evaluated. An approximate emperical expression developed from a mathematical analysis provides a means of converting the frequency into tension. The method appears to be effective in mines with shale roof but requires some modification for other roofs.

Jan 1, 1983

By Kevin Connor

The mineral industry continued to be an almost negligible contributor to the country's economy as the Government continued its 1979 ban on any mineral exploitation for export; a policy initiated at the end of 1979. A national program had been underway since that time to map and inventory all mineral resources so as to permit future exploitation of mineral wealth in the beat interests of the country and its inhabitants. In March 1982, the British Sulphur Corp. Ltd., under contract to the Burundi Government and the International Bank for Reconstruction and Development (World Bank), began a feasibility study of Burundi's phosphate deposits at Matongo-Bandaga for potential commercial exploitation. The 1-year project effort was to define ore reserves, conceptually design mining operations and processing facilities, estimate capital and production cost, and develop a regional market and distribution survey. Work completed during the year comprised geological exploration and reconnaissance and 1,200 meters of core drilling. Reserves in excess of 5 million tons of ore-grade phosphate were estimated available for mining. Rare earth mineralization was associated with the primary apatite. The associated carbonatite within the rock matrix was preliminarily assessed to be of value as a raw material for the manufacture of cement. The contract effort was valued at $1.2 million? Matongo-Bandaga is located approximately 40 kilometers north of the capital city of Bujumbura and alongside one of the country's few paved roads.

Jan 1, 1984

By George S. Rice

There have appeared, from time to time, comparisons of various features of coal mining practice in the United States and Great Britain. A recent, article, appearing in a British journal, points out that the American miner produces 3 1/2 times as much coal per shift as the miner, at one-half the cost, and proceeds to explain the natural industrial, and engineering causes which lead to this result. Amon« he reasons advanced. is that the American coal miner enjoys the advantage of more easily worked seams of coal, due to the fact that the coal mining industry in the United States is of more recent date than in Great Britain. The latter qualification is not correct, because where these advantages exist, they will persist. The coal beds of the United States are not buried deeply, except in the remote parts of the country, as in the Uinta Basin of Utah. The article referred to states that many of our miners are still employed on out seams reached by "adits", (which we term entries), or by vertical shafts of moderate depth. It is probable in fact that the great bulk of the coal of the United States is taken out from a depth of less than 400 feet.

Mar 1, 1920

By A. W. Henderson

Methods for converting WOCl4 to WCle were investigated in small-scale, laboratory apparatus to devise a method for preparing pure WCls suitable for conversion to tungsten metal. Chlorine, COCI2, and CCI4, alone and in combination with various forms of carbon, were tested as chlorinating agents at various temperatures. More than 95 percent conversion of WOCl4 to WCls was achieved with all reagents at 8000 C in the presence of activated carbon. Only CCl4 maintained its effectiveness in the absence of carbon at 800° C. The effectiveness of carbon was found to be related directly to its surface area.

Jan 1, 1968

By W. S. Anderson

The use of flexible liners for support of underground openings has been investigated by the Bureau of Mines. This report presents installation procedures and instrumentation results of a full-scale flexible liner field installation in the Burgin mine. The flexible liner is a part of the mine support system and has provided maintenance-free support for 22 months

Jan 1, 1975