Search Documents

By Oliver W. Keener

The operation described herein differs from the usual practice in the Tri-State district in two important respects: (1) the ore is loaded into cars which are tramped to the shaft and hoisted on self-dumping cages, and (2) about 30 per cent of the ore is loaded by power shovels. The four-month period covered by the cost data appended at the end of the paper immediately followed a period of about one year during which the mine was shut down, and the expense incident to the resumption of operations is reflected in the costs. The author acknowledges the assistance of C. F. Jackson, mining engineer, U. S. Bureau of Mines, in the preparation of this paper and the compilation of the data.

Jan 1, 1929

By Launa G. Mallett, Kathleen M. Kowalski, Michael J. Brnich

The characteristics of leaders under the duress of an emergency are important in the development of emergency planning, training, and in the management of an actual emergency. Knowledge of human behavior is an important component in the formation of emergency strategies. The U.S. Bureau of Mines analyzed the leadership behavior in three underground mine fire escapes. The subjects described their escapes during open-ended interviews. Data were coded according to: (1) evidence of leadership behavior, (2) evidence of lack of leadership behavior, and (3) characteristics of the individual in each group who led the subjects out of the mines. This paper discusses the profile of six individual leadership characteristics which emerged from the data.

By Scott Turner

The settlers of a new country necessarily suffer at first from the lack of accumulated stocks of metals - in-use that are possessed in older countries . Our American colonists were at first compelled to import their metals in manufactured forms , and it must have proved difficult to produce an exportable surplus of commodities with which to pay for them . These circumstances stimulated a search for domestic ore deposits . Various discoveries resulted , so that as early as 1628 , we find the colonists importing two craftsmen from England to establish iron -works in Massachusetts to beneficiate local ores . In 1648 , an iron -works at Lynn was producing metal at an annual rate of 400 tons . Later on , the colonial iron industries became of importance , some metal being actually exported to England . The people of this country thus early became convinced of the necessity for domestic mineral production . It is now little realized how persistent were their efforts to - make mineral discoveries , before the gold- rush to California ; the extraordinary success of our subsequent mineral explorations has overshadowed the earlier record . Precise and complete accounting of our mineral production , having the character of national bookkeeping , is available only for the series of years beginning with 1880 , when commences the official record that is provided by the Government publication called Mineral Resources of the United States . In the period of 52 years , from 1880 through 1932 , the value of mineral production of the United States amounted to more than 122 billion dollars . Only 12 billions of this total were produced in the 21 years , 1880-1900 , while nearly 110 billions were produced in the first 31 years of the present century . Of this 110 billions , over 53 billions were produced in the most recent decade , 1921- 1930 , the production of the previous decade , 1911-1920 , having been only 37 billions , though it included the war period ; that of the decade 1901-1910 was 16 billions . In 1931 , the total value of mineral products of the United States was $ 3,180,000,000 , compared with an average annual value of $ 5,556,000,000 during the previous five - year period , 1926-1930 . The decline in 1931 from that average was therefore 43 per cent . As to the three great groups of mineral commodities , metals fared worst , with a decline of 55 per cent in the value of their production , while the value of fuels declined 39 per cent , as did that of the nonmetals group .

Jan 1, 1933

By Maria I. De Rosa

The U.S. Department of Energy Pittsburgh Research Center2 conducted experiments with mine conveyor belt samples in a 20-L furnace and in a laboratory fire tunnel to measure and compare the major toxic gas concentrations evolved during the combustion of the materials. The toxic gas concentrations, measured simultaneously through a multiport sampling device and treated as yield values, included hydrogen chloride (HO), hydrogen cyanide (HeN), oxides of nitrogen (NO, treated as NO), and carbon monoxide (CO). The data obtained from the two experimental systems were in good agreement. Correlations were developed for the toxic gas yields as a function of the percentage of chlorine (for HO gas), nitrogen (for HCN and NO, gases), and carbon (for CO gas) contained in the original materials. The toxic gas yields were also used to calculate a toxicity index (TI) parameter to assess the potential gas toxicity of belt materials during a fire. Furthermore, the TI and the mass loss burning rate values were used to calculate a toxicity hazard (TH) parameter to estimate the toxic gas hazard produced by a burning belt in a ventilated system. Results show that polyvinyl chloride (PVC) belts released higher HC1 concentrations because of the higher chlorine content; styrene-butadiene rubber (SBR) belts released higher CO, HCN, and NOz concentrations because of the higher carbon and nitrogen contents. The TI's, however, were greater for the PVC belts due primarily to the higher levels of HC1 produced. The fire tunnel data indicate that the SBR belts can bum with higher mass loss rates than the PVC belts, resulting in a potentially higher toxic hazard (higher TH values) even though their TI values were lower than those of the PVC belts.

By G. Nuñez, M. A. Pathak, A. A. Afshari, C. F. Stanley

"To help evaluate the vibration patterns of an excised lung, a method is developed to determine which parts of the surface of an excised lung are responding to acoustic excitation via the trachea. Holographic interferometry, a very' sensitive technique ·that can measure movements of a few microns, is used to detect the lung surface movements.The intact lung and heart are excised from Long· Evans male rats weighing 250 gm. A tube is inserted into the trachea and connected via a funnel to a 3 inch cone speaker. The assembly is positioned in the holographic unit and excited at frequencies up to 10,000 Hz. The holographic unit contains an acousto-optic shutter used with a 0.5 watt Argon laser.The resulting reconstructed holograms contain interference fringes that are indicated of lung surface vibration.INTRODUCTIONA 1986 report by the U.S. National Committee on Biomechanics [1] describes diseases of the lung as a major national health problem. One of the recommendations of the report is for continued study of the mechanical properties of lung tissue. As an example, the report cites at least three areas that would benefit from a better understanding of the vibratory patterns or the lung."

Jan 1, 1989

Underground and strip mining (6,7) produce different hydrologic environments. Many underground mines are below the zone that is completely saturated with water and the mine openings may cause new and continuous contact between sulfurous material and water which flows from the saturated zone to the workings. Strip mines are usually above the zone of continuous saturation and contact between sulfurous material and water is generally restricted to periods of precipitation. A full appreciation of the problem of water pollution caused by drainage from deep mines requires a basic understanding of occurrences and movement of water in the ground and the modes of ground water entrance into mining areas.

Jan 1, 1970

Provide ear protection which allows normal, unaltered hearing at low noise levels, yet protects the wearer from excessive noise. The Approach: A commercial earmuff with integral speakers has been adapted with a special amplifier so that low sound levels are not affected, but higher noise levels automatically reduced. How It Works: The discriminating earmuff developed by the Bureau of Mines has two modes of operation. In the first mode, where input sound levels are less than or equal to 83 decibels, the wearer will perceive noise at its actual level. For inputs in excess of 83 decibels, the second mode of operation begins and the sound perceived by the wearer is progressively attenuated, or reduced, as the input level is increased. A recognizable difference still exists between two adjacent sound levels enabling the wearer to differentiate between them.

Jan 1, 1975

By T. F. Anstett

The Bureau of Mines investigated the availability of platinum from known major deposits in market economy countries. Fifteen of these deposits contain demonstrated resources totaling 302 million troy ounces of platinum. Detailed geologic, engineering, and cost evaluations were performed on each deposit to determine its potential for platinum production. There are large amounts of demonstrated platinum potentially available from market economy deposits that were not analyzed owing to lack of adequate data or to technological limitations. These include 297 million troy ounces contained in the UG2 and Platreef of the Bushveld Complex, South Africa. This analysis indicates that about 11 0 million troy ounces (2.3 million ounces annually) of platinum are potentially available at the January 1980 producer price of $420 per troy ounce, nearly all from South Africa. An additional 85 million troy ounces occurring in Zimbabwean deposits would become available only through more than a quadrupling of that price. In order to meet projected world demand of 3.5 million troy ounces in 1990, platinum price may have to increase. Only one domestic deposit, the Salmon River in Alaska, is capable of producing platinum at $420 per troy ounce. Regardless of price, at assumed production capacities, domestic deposits could supply less than 10 percent of annual U.S. requirements.

Jan 1, 1982

"At the request of the Anthracite Institute, the United States Bureau of Mines during February, March, and April 1935, made a field survey of commercial anthracite shipped from collieries scattered throughout the Anthracite regions. In all, 268 samples were taken at 41 breakers from Carbondale at the northern end of the field to Pottsville at the south. These collieries ship approximately 50 percent of the industry’s total production. The geographical distribution of the breakers sampled was as nearly as practicable in proportion to the tonnage of the companies from each region cooperating in the plan.The following are the weighted average analyses, by sizes, of the samples taken in this survey;"

Jul 1, 1935

By Jon C. Volkwein

The industrial sand industry has been exploring new techniques to reduce dust. One company was experimenting with adding water during bagging operations to the surface of the hag, and into the product as it flowed into the bag. The Bureau of Mines, using instantaneous dust sampling instruments, measured the effectiveness of three methods of adding water. Results indicated that various types of water sprays applied in carefully controlled amounts could reduce dust up to 50% at worker locations at the bagging machine and inside a railroad boxcar. This report also discusses constraints such as product handling, customer acceptance, cold weather problems, dust collector performance, and other areas.

Jan 1, 1981

By Launa Mallett, Michael J. Brnich

The first step to emergency preparedness is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen all at once. Risk assessments are used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. While the examples provided in this training package are specific to mine fires, the concepts and tools can be applied to any mine hazard. Purpose: This training package was developed to assist instructors, as they: 1) determine how to use risk assessment to improve preparedness for mine fire emergencies and 2) present risk assessment concepts and tools to trainees. Audience: This package is appropriate for workers/trainees from all types of mines. A risk analysis can be conducted by anyone familiar with the location(s) being studied. Why Conduct a Fire Risk Assessment? During a risk assessment, hazards are evaluated in terms of the likelihood that a problem may occur and the damage it might cause. Mine fire preparedness requires consideration of all possible fires that could occur. However, at a given mine some fires are more likely than others and some would result in greater damage than would others. Conducting a risk analysis identifies these differences. The results can be used to target resources at the types of fires that are most likely and/or are most destructive. Hazards that are very likely to result in fires that would do considerable damage to people and property should be targeted first for remediation and/or effective response if remediation isn't possible. Potential fires that are less likely or that would have less severe consequences are identified for attention later, after the more serious situations have been addressed.

Jan 10, 1992

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

Engineering controls for overburden drilling include dry dust collection systems, wet dust suppression systems, and enclosed cabs [Zimmer and Lueck 1986; Volkwein et al. 1979]. Proper maintenance of the dust suppression system is critically important for drills using dry dust suppression methods. Failure to rigorously maintain these systems will result in inadequate dust control. Acute silicosis has been reported in miners operating equipment that relies on dry dust suppression [NOSH 1992].

Jan 1, 1997

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. DATA INPUT FOR THE OPERATING PROTOTYPE [To run the Rail Haulage Model independent of the Production Sub-system, remove the production data from card type four through the blank card following END DATA on page B18 and change the fourth data element under ADDITIONAL DATA from 1 To 0.]

Jan 1, 1974

By Jozef S. Stachulak

In This Chapter [Ore pass dust control Drill dust control Blasting dust control Conveyor belt dust control Transfer point and crusher dust control Roadheader dust control and How much ventilation air to use] This chapter discusses respirable dust control in underground hard-rock mines. These mines use a wide variety of extraction methods, but they have many common dust sources and dust control needs. Ore passes, drills, blasting, conveyor belts, transfer points, crushers, and load-haul-dump operations can be major sources of dust. Roadheaders, which are sometimes used in hard-rock mines, produce dust in large quantities. For the most part, dust in hard-rock mines is controlled with ventilation air, water sprays, and dust collectors. It is also important to prevent dust from getting into the air in the first place. Good dust control practices will reduce overall mine ventilation requirements. [Lack of maintenance is the main source of dust problems in hard-rock mines according to Rodgers [1974], who conducted a dust survey of hard-rock mines several decades ago. Rodgers found that spray systems had clogged sprays, dust enclosures had improperly fitted skirts, and ductwork was plugged and had leaks. Today’s mines have better maintenance programs (we think), but when dust levels are high, maintenance is still the first topic to address.] The Mining Association of Canada [MAC 1980] and Knight [1980] provide good general information about hard-rock dust control. For conveyor belt dust control, Goldbeck and Marti [1996] and Swinderman et al. [1997] are valuable sources of information.

Jan 6, 2003

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

By Donald R. Irving

THIS CHAPTER is new to the Minerals Yearbook and will appear regularly hereafter. Its purpose is to present statistics that reflect technologic trends in the minerals and metals industries (except fuels). Much useful information has been collected annually through the Bureau of Mines mineral commodity and employment and injuries canvasses. However, these data must be supplemented by further data to permit evaluation of the type, direction, and rate of technologic change, which are vitally important in long-term mineral planning. In addition to, and fully as important as, expanding the available data is the need to ascertain that the various items collected are obtained from identical reporting units, to enable direct comparisons to be made.

Jan 1, 1960

By S. B. Levin

"INTRODUCTION An exposure of large beryl crystals in pegmatite on Beryl Mountain, in Sullivan County, N. H., was the basis for investigation by the Bureau of Mines to determine the extent of the beryl mineralization and to expose other parts of the same zone that were favorable for additional beryl-rich shoots. Testing by surface cuts, trenching, and tunneling was conducted by the Bureau of Mines from August to December 1943.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests. The field work was supervised by Paul M. Tyler, regional engineer, and John D. Bardill, district engineer. S. B, Levin was in direct charge of the project.LOCATION AND ACCESSIBILITYThe deposit is on the northeast slope of Beryl Mountain, 1 mile south of the village of South Acworth. The village, on State Highways 101 and 123a, is 12 miles northeast of Bellows Falls, Vt. The deposit is reached from South Acworth over a gravel-surfaced road and about 1,000 feet of good truck trail (fig. 1).The nearest railroad siding is at Cold River, on the Boston & Maine Railroad, where there is also a fairly modern, but now idle, feldspar mill."

Mar 1, 1948

By A. B. Needham

The Great Eastern nickel deposit is located in the western foothills of the Virgin Mountains in the Copper King or Bunkerville district situated in the southeastern part of Clark County, Nev. It is covered by a group of eight claims that can be reached by turning south from U. S. Highway 91 at Riverside, Nev., and driving about 12.6 miles southeast over a winding mountain road, which rises from about 3,000 feet to 4,000 feet in elevation. The climate is dry, with only a small amount of rainfall throughout the year. The temperature ranges from hot during the summer to short periods of freezing weather during the winter months. The vegetation is of the desert variety, and no timber is available for mining. Water for mining purposes would have to be pumped from lower areas. A granitoid gneiss comprises the largest part of the rock outcrops. It has a steeply dipping foliation that strikes about N. 75° E. The gneiss was intruded by basic dikes, which in turn were intruded by pegmatite dikes. The ore occurs as lenticular bodies formed by the convergence of several pegmatite dikes within the main dike. The principal sulfide minerals are pyrite, pyrrhotite, and chalcopyrite, which contain a small amount of nickel. Late in the year of 1939, the Bureau of Mines undertook an exploration project on the Great Eastern property to extend or delimit the known mineralization. Underground work, consisting of 590 feet of drifting and crosscutting, was completed in September 1940, and 1,091 feet of diamond, drilling for downward extension of an ore body in the Lower edit, which was completed in February 1941.

Jan 1, 1950