Search Documents

By R. V. Ramani, A. S. C. Owili-eger

Mathematical modeling is a scientific exercise with the objective of developing simplified mathematical statements that relate to one another the same way as the processes that are being modeled. The utility value of the model is dependent on the ability of the model to closely approximate prototype behavior. Development of a perfect model, therefore, is an unrealistic objective because of the simpli¬fying assumptions made in building it. However, for a model to be acceptable for application, its operating characteristics or data generated from it should, within reasonable accuracy, duplicate proto¬performance. The validity and accuracy of a model depends on the mathematical constraints presupposed in model formulation. The final model must be tested for mathematical validity and for closeness of representation of the prototype. Mathematical validity, does not, however, imply that the model is accurate and correct but is prerequisite. Model testing and verification for the steady state model are given in Owili-Eger et al (1973). The unsteady state model has been tested for mathematical validity and found to be correct but has not yet been applied to a field condition for lack of data. However, in the application discussed below, the unsteady state model results are compared with pressure curves reported in literature and also with results from the steady state model. Coal seam characteristics and gas reservoir pressure used in this application are extracted from Kissell (1972). These characteristics are for the Pittsburgh seam, Federal No. 2 Mine, Fairview, West Virginia.

Jan 1, 1974

By E. D. Gardner

"The town of Ajo is built in the desert and consisted of but a few houses when the New Cornelia Copper Co. started operations. Since there were no stores at Ajo or vicinity the New Cornelia Cooperative Mercantile Co. was established to serve the needs of the employees of the New Cornelia and allied companies.The New Cornelia Copper Co. advanced the money to erect the store building and to buy the stock, and assumes all risks. In all, $85,000 has been advanced, representing the capital stock of the enterprise.The store is run by a store manager appointed by the Copper Company and who reports only to the general superintendent. A committee of seven workmen, representing the various depart¬ments, meet with the store manager monthly and make suggestions for the betterment of the service and, present complaints which have been brought to their attention.The store is well managed, carries a large and well assorted stock and is modern in every respect. Prices are at the same level as in the other Southwestern mining camps. The Copper Company does not particpate in the profits of the store but does receive six per cent interest on the capital advanced. At the end of the year, after making proper deductions for interest on capital account, depreciation of store equipment and fixtures, and, for a proper sum to the surplus account, the rest of the profits is distributed among the employees of the company in proportion to the amount of their purchases."

Aug 1, 1920

It is suggested in chapter 1 that emergency activities (including escape) are not individualistic. They tend to be group responses. If escapes from mine fires are group activities, then preparation for such events must take group behavior into account. This chapter explores the hypothesis that the miners who escaped from the three mines under study did so as members of groups. For development of this chapter, the database was examined for evidence of the existence of escape groups and for instances when individualistic behavior was paramount. Illustrations of group and/or individualistic behavior were analyzed and representative examples are provided in the following discussion. The nature of groups was discussed in chapter 3 and the following working definition was offered: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at second-hand, through other people, but face-to-face" [Homans 1950]. To determine whether or not groups existed during the fire evacuations, it is important that the concept of group be clearly defined. Therefore, the discussion started in chapter 3 will be elaborated here. The defining characteristics of group given in chapter 3 were taken from Homans [1950]. They include size, person-to-person com¬munication, feelings that members have for each other, explicit and implicit rules for behavior, and common activities. An additional characteristic that is sometimes used to define groups is cohesiveness. Kiesler and Kiesler [1970] state, "Cohesiveness would include not only the attraction that the group holds for its members but also any other force operating on the individual to stay in the group." Variables said to contribute to cohesiveness include "(1) the attractiveness of a group for its members," and "(2) the coordination of the efforts of the members" [Keisler 1970]. One source of the attraction to a group occurs when "the goals or exterior tasks confronting the group are consistent with those of the individual person, and can best be handled by group action" [Cartwright and Zander 1968, in Davis 1969]. In other words, a common goal and a coordinated effort mounted to achieve that goal contributes toward the creation of a cohesive group. As discussed in the earlier review of research (chapter 1), groups have frequently been studied in laboratory or simulation settings. These methods allowed control over variables of interest. Kiesler and Kiesler [1970] state, however, that they "find group variables conceptually imprecise and experimentally difficult to work with." Experimental control, in other words, is difficult to achieve in the study of groups. The richness of the naturalistic mine fire data may provide an opportunity for an examination of groups that cannot be found in laboratories or simulations because this environment was not

Jan 1, 2000

By Jeffrey B. Osmint

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1991

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Exposure to excessive noise over time can cause permanent hearing loss. Workers in the mining industry are frequently exposed to A-weighted sound levels in excess of 90 dB. The A-weighted sound level at the roof bolter operator’s location can exceed 100 dB while drilling. The National Institute for Occupational Safety and Health (NIOSH) measured the sound pressure at the roof bolter operator’s position and utilized a phased array of microphones with beamforming software to identify noise sources on a roof bolting machine while drilling. The test data indicates the sound level at the operator’s position is dominated by the 2000 Hz through 5000 Hz one-third­octave-band sound levels. The beamforming results indicate that the drilling noise is primarily from two areas: the portion of the drill steel just below the rock and the drill steel-chuck interface. This paper will discuss the methods used to identify the primary noise sources.

By Christopher C. Jobes, Alan G. Mayton, Farid Amirouche

Based on prior mine vehicle studies of operators’ exposure to whole-body vibration, researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated four seat designs on mine haulage vehicles, with regard to roadway-induced jarring/jolting and operator comfort. Investigators collected objective and subjective data from vehicle operators on two existing and two NIOSH seat designs. This study included time and frequency response data using accelerometers and a data recorder, operator perceptions of jarring/jolting and discomfort levels using a linear visual analogue scale, and data from a questionnaire developed for this study. Results from the analysis of subjective data show that operators generally favoured the NIOSH-designed seats over the existing seats. The results of analyses from the absorbed power method and the threshold limit method, based on ISO 2631-1 (ISO, 1985), support the premise that NIOSH seat designs are superior to the existing vehicle seat designs on both models of mine shuttle cars used in the study. The NIOSH seat designs, featuring viscoelastic foam padding, were more effective in reducing vibration energy for operators exposed to vehicle jarring/jolting. In this paper, the performances of the NIOSH and existing seat designs are compared relative to the operator’s exposure to vehicle vibration (mainly jarring/jolting).

By Erica E. Hall, Robert H. Peters, Charles Vaught, Jon C. Volkwein

Coal Workers Pneumoconiosis is the leading cause of death due to occupational illness among coal miners. This disease is caused by miners’ exposure to respirable coal mine dust. A Personal Dust Monitor has recently been developed to provide near real time feedback to miners regarding the number of milligrams of respirable coal mine dust in the air they breathe. This paper was prepared by the National Institute for Occupational Safety and Health to document coal miners’ reactions to this new device, and how they make use of the information it provides. Structured interviews were conducted with 30 coal miners at four mines. A four-stage conceptual model of miners’ decision processes with respect to how they interpret and respond to the dust exposure numbers from their personal dust monitor is proposed. The stages are: Diagnosis, Action Planning and Intervention, Evaluation, and Institutionalization. The interview responses provide considerable support for the model. Most miners paid attention to Personal Dust Monitor feedback and made efforts to reduce their dust exposure. Their efforts included: changing where they positioned themselves, making ventilation system improvements, and using respirators more often. The 29 miners who reported having experience wearing both the old and new type of dust monitors were asked which dust sampling system they preferred. Eighteen (62%) preferred the new monitors, 7 (24%) preferred existing monitors, and 4 (14%) had no preference. The most frequently cited advantage of the new monitor is its ability to provide relatively quick feedback on dust exposure. Miners provided several suggestions for improving the design of the instrument.

By S. D. Hudock, C. M. Keran

A review of all upper extremity cumulative trauma disorder (UECTD) injuries was conducted by the U.S. Bureau of Mines for 1985 through 1989. This review was performed by analyzing each injury, as reported by law and maintained on the U.S. Mine Safety and Health Administration's accident data base. This analysis found that incidence rates in mining were lower than in private sector industry, although the number of reported UECTD injuries increased sevenfold and their percentage of all mining injuries increased fivefold from 1985 through 1989. Metal-nonmetal mines accounted for 80 pct of UECTD injuries, while coal mines accounted for 20 pct. Nearly 63 pct of UECTD injuries were accounted for by only four occupations-mechanics, laborers, boney (crusher) operators, and miners not elsewhere classified (NEC)-with an incidence rate well above the private sector industry rate.

Jan 1, 1992

By ALBERT C. DURHAM

In anthracite mining , pumping is a problem of major importance , and water must be handled and rehandled in almost every mine whether the mine is in operation or idle . The motor - driven centrifugal pump is the most commonly used type of unit for the large pumping installations, and experience has . proved that fully automatic control has certain advantages over manual control . Some of these advantages are greater safety for maintenance personnel , continuous protection against faulty operation , which could cause damage to the Lumping apparatus , and lower pump -room operating costs .

Aug 1, 1948

By M. Viswanathan, M. J. Jorgensen, N. K. Kittusamy

Operating heavy construction equipment is often associated with elevated rates of low back discomfort (LBD). However, there have been few formal studies that dealt with evaluating controls that can reduce the LBD among these workers. The objective of this study was to determine the effectiveness of using a continuous passive lumbar motion system (CPLMS) in reducing low back discomfort among operators of heavy earthmoving equipment. The CPLMS is an additional seat support that has a lumbar support bladder and a pump to provide cyclic inflation and deflation. Two groups of operators were identified as potential subjects for this intervention study, the intervention group with a mean age of 41.2 years and experience of 9.7 years used the CPLMS, and the control group with a mean age of 37.5 years and experience of 7.6 years did not use the CPLMS. Body part discomfort surveys were collected from both groups. In addition, the intervention group completed a CPLMS preference survey. The body part discomfort survey was collected up to eight days at three different times of the day. Results from the body part discomfort survey showed a decreasing trend the longer the CPLMS was used, for both the upper and low back region. A decreasing trend for the low back was also found comparing morning to evening discomfort scores across the days when using the CPLMS. When compared to their regular seat, 54% of the operators felt very comfortable in using the CPLMS, 36% of them wanted one for their equipment, and 54% showed interest in experimenting with the CPLMS for a longer time period. Results from this study indicate that the use of a CPLMS can effectively reduce the low back discomfort experienced by operators of heavy construction equipment.

By Oliver Bowles

"Rhodesian asbestos is of high quality and is much in demand by American consumers. Production in Rhodesia was first reported in 1909. The production for this and each succeeding year is shown in the following table:The serious curtailment in production for the years 1912 and 1913 was occasioned by transportation difficulties. In 1914 a railway was projected to Victoria and thereafter production increased greatly. Up to 1916 asbestos was obtained,from the Victoria district only, but thereafter the Bulwayo district became an important,producer with minor quantities from Gwelo.In the Bulawayo district the productive area is about 2 1/2 miles long, with Shebanie mine at the north-west end, the Nil Desperandum at the south end, and the Birthday claims between them."

Oct 1, 1920

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

8. Refuge Chambers 8.1 Refuge Chambers - Technical Discussion 8.1.1 Introduction As a part of the overall escape system, refuge chambers can provide a last resort when existing escapeways are blocked. These chambers are intended to provide both protection from toxic gases and a life supporting environment for a period of time before external rescue or further escape efforts can be carried out Escapeways may be blocked physically (due to cave-ins, etc), by fire, or by the presence of a toxic or oxygen deficient atmosphere. In the first two cases, the trapped miners would most likely await external rescue efforts, and hence the design of the chamber will have to consider the time durations that such efforts may take, It is also possible, in the second case, for fire fighting and fire protective equipment to be stored in the chamber so that miners may attempt their own escape. In the third case, it should be recognized that a compact, beltmounted 1-hour self-contained breathing apparatus has been developed(9), and that other, less compact equipment is available for up to 4 hours of self-contained breathing supply. If such equipment were stored in the chambers, then miners could escape by travelling from chamber to chamber, taking temporary refuge in each before proceeding to the next. 8.1.2 Background The concept of "barricading" has long been recommended for those emergencies where miners are trapped inby a fire. Barricading, which is the construction of a makeshift shelter in a crosscut or deadend, protects the entrapped miners from toxic gases and enables them to conserve a supply of air. In this manner, they can survive two or three days--hopefully enough time for them to be reached by rescue teams. In the past, many lives have been saved with this technique.

Jan 1, 1976

By N. A. Caspero, W. E. Eckard, W. T. Wertman

A thermal oil-recovery experiment was conducted in the Venango First sand, Goodwill Hill oilfield, Warren County, Pa., about 10 miles northeast of Titusville. The Quaker State Oil Refining Corp., Bradford, Pa., performed the experiment with assistance from Sinclair Research, Inc., Tulsa, Okla., and the Federal Bureau of Mines. The Goodwill Hill field was discovered in 1885. Primary-production oper- ations continued until 1930 when an air-gas injection project, which is still in operation, was started. At the location of the combustion experiment, the reservoir is 400 feet deep and 30 feet thick, with wide permeability and porosity variations. The crude oil is typical Pennsylvania Grade paraffin- base oil with a gravity of 43.9° API and a viscosity of 4.55 cp at 60° F. The well pattern for the experiment consisted of 5 producing wells, enclosing an area of 1.28 acres, and a central ignition-injection well. An air-natural gas mixture was ignited in the ignition well on July 29, 1961. Ignition was followed by injection of air and natural gas at various rates. The experiment was suspended January 5, 1962, when it became evident that economic oil production could not be achieved. There was no conclusive evidence that self-sustained combustion was achieved or that combustion increased oil and water production. A slight increase in liquid production was attributed to stripping action caused by the air-injection rates, which were higher than those normally used during air-gas injection.

Dec 1, 1963

By P. Kovalchik, S. Peng, G. Cole, R. Matetic

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90 percent of coal miners and 49 percent of metal/nonmetal miners had a hearing impairment by age 50 (Franks, 1997). Mine workers are exposed to additional noise levels underground due to the reflection of machine-generated noise that would otherwise dissipate in an aboveground setting. Determining the sound-absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed rather than being reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes a finite room, a diffuse field and a relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper presents a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients are essential for determining and predicting potential overexposure to machine operators in different mine environments.1

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7. 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1985

By Louis C. Brichta

The Rush Creek district of Marion County, Ark., has had a more or less continuous record of zinc production over the past 40 years. The ore has come from many small mines working on oxidized and semi-oxidized deposits found in the Everton formation where that formation forms the present surface rock. Prospecting has been restricted to the hillsides above the creek levels, the actual ore outcrops being the guides. Little attention has been paid the possible sulfide zones. In August 1942, the United States Geological Survey and the Bureau of Mines recommended exploration of the Powell and Cotter formations, which underlie the Everton, for which purpose the Survey had previously located 18 proposed drill-hole sites in geological structures that seemed favorable to are deposition.

Jan 1, 1949

By John R. Benham

The Blue Joint Mtn. RARE II area may contain barite resources. One claim, the Woods Creek Barite No. 1, contains two veins of barite of drilling mud quality. The quantity of barite present could not be determined due to limited surface exposures. Sections 1, 2, 11 and 12 of T. 2 S., R. 23 W. in the study area are classified by the U.S. Geological Survey as prospectively valuable for geothermal energy resources. These sections border Blue Joint Creek Hot Springs, which are outside the study area.

Jan 1, 1981

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7. 1882 (22 Stat. 829) to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1987

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

By Allen Q. Howard

An approximate solution to the electromagnetic boundary value problem consisting of a horizontal cylindrical conductor buried in a lossy half-space and excited by an arbitrarily oriented magnetic dipole is found using an iterative perturbation technique in a double Fourier transform space. This model is used to gain insight into the anomalous fields due to strong scatterers such as pipes or tracks which would be in close proximity to an EM mine rescue operation. The novel, three-dimensional aspect of the problem (i.e., the source) imposes the complexity that the current in the cylinder is not uniform. The field expressions are ideally suited to evaluation using FFT algorithm.

Jan 1, 1973