Search Documents

By J. E. Tress

The Bureau of Mines prepared submicron tungsten powder by reducing tungsten hexachloride with hydrogen. The particle diameters of the resulting tungsten powders ranged from 0.015 to 0.046 micron. Within the limits of the variables investigated, no clear-cut correlation was found between process conditions and final size of the powder. Oxygen was the major contaminant in the product; being present both as an adsorbed gas and as suboxides of tungsten. Studies showed that the powder yielded compacts of approximately 45 per-cent of theoretical density when compacted mechanically. Low-temperature sintering produced more rapid densification in these compacts than in compacts prepared from conventional powders. Adding up to 20 percent ultrafine powder to conventional tungsten powder caused an increase in density upon compaction with maximum densification occurring at approximately 12 percent ultrafine powder.

Jan 1, 1966

By R. R. Sayers, W. J. McConnell

"The health, comfort, and efficiency of men engaged in the mining industry may be impaired, in some instances very seriously, by abnormal physical conditions of the mine air or by variations in its composition. This is true in some of sheet metal mines of the West where high temperatures with varying humidities are encountered. Physiological studies have been made in some of these mines showing the effects of various temperatures end humidities. As it is difficult to carry out studies on many controlled temperatures, it was thought best to make the experiments in a laboratory and apply the results to the industry insofar as practicableThe effects of moderately high temperatures and humidities are more difficult to measure perhaps than the extreme conditions, but may be predisposing causes of fatigue, discomfort and disease, A cooperative study of the physioloical effects of heat and humidity is being conducted by the Bureau of Mines and the U. S. Public Health Service cooperative with the American Society of Heating and Ventilating Engineers, in the Research Laboratory of the Bureau of Mines at Pittsburgh, Pa."

Mar 1, 1924

By N. A. Gokcen

This Bureau of Mines report reviews and summarizes recent studies of the rates of chlorination of aluminous resources with CO and C12 mixtures with and without COC12. No reaction mechanism could be obtained from the existing results; however, diffusional barriers in the gas and solid layers probably control the chlorination rate in thermogravimetric experiments. Fluidized beds of particles smaller than 0.1 mm appeared to show very little solid layer diffusional barrier. For optimum chlorination the particle size should probably be less than 8 mm, the calcination temperature approximately 700° C, and the chlorination temperature from 650° to 750° C. Relatively rapid chlorination with COC12 in thermogravimetric experiments was attributed partly to the simultaneous supply of reductant and chlorinator by one gas to the sample reaction site. Comparable results for chlorination of fluidized beds with COC12 are not available. Equimolar mixtures of CO and C12 produced the optimum rate of reaction. Addition to the calcine of 10 to 20 wt-pct NaCl accelerated the rate of chlorination, and addition of SiC14 to the gas mixture decreased the rate of chlorination of SiO2 drastically, but at the expense of chlorination of significant fractions of Al2O3. Further research in various areas is suggested.

Jan 1, 1983

By William O. Vanderburg

This paper describing the methods and costs of milling scheelite ore at the Silver Dike concentrator of the Nevada-Massachusetts Co., Inc., is one of a series being prepared by the Bureau of Mines. In the Silver Dike mill tungsten ore which contains about 1 per cent of scheelite is treated at the maximum rate of 45 tens per 24 hours by tabling followed by magnetic separators to clean the table concentrates. Unusually high-grade concentrates are produced which average between 70 and 75 per cent of W03.

Jan 1, 1932

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

By Geo. Adams Roalfe

THIS PAPER is one of a series being pre¬pared for and published by the United States Bureau of Mines describing, methods of mining and crushing and the costs of operation at commercial crushed-stone plants throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators, as well as to the industry as a whole. On the other hand, operating, costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. Acknowledgments The author wishes to acknowledge the [ ]

Jan 1, 1932

By H. E. Camargo

In an effort to decrease noise-induced hearing loss (NIHL) in coal preparation plant employees, the National Institute for Occupational Safety and Health (NIOSH) is conduct­ing research to identify and control dominant noise sources in vibrating screen (VS) machines. To this end, acoustic measurements of the noise radiated by a dewatering VS were conducted at the Pittsburgh Research Laboratory (PRL) using microphone phased-array technology. These measurements allowed for the identification of the screen as the dominant source in the 250 Hz 1/3-octave band. The sidewalls are the major contributors in the 315 and 400 Hz bands, whereas the eccentric mechanisms and the electric motor are the dominant sources in the 800 and 1,000 Hz bands, respectively.

Jan 1, 2009

By David F. Smith

[The U. S. Bureau of Mines at its Pittsburgh Experiment Station is frequently called upon to determine by laboratory tests the explosibility of suspensions in air of various dusts encountered in mines and elsewhere. Not all dusts which are combustible or contain combustible material will form explosive mixtures with air under ordinary conditions of temperature and pressure. They may not be highly combustible enough. They may contain a considerable amount of inert or non-combustible material or, the dust particles may not, be fine enough to form explosive mixtures. A knowledge off the chemical composition of a dust together with a determination of the size of the particles often gives valuable indications. But in many cases actual explosibility tests are necessary. Such a case is evidently that of powdered soap, whose explosibility hazard the Bureau was recently called upon to determine, Although an explosion which occurred in a soap plant as early as 1890 was attributed4 to powdered soap, it is apparent, due to the great number of inquiries received by the Bureau, that the hazard presented by powdered soap has not been at all generally appreciated. To the writers' knowledge, no extensive investigation of the explosibility of powdered soaps has been made. It is only recently that pure powdered soap has been manufactured on a large scale. The familiar "soap powder" in the past was usually a mixture of soap with a relatively large quantity of sodium carbonate. Often it contained large amounts of moisture and abrasive material. Even a highly combustible dust when mixed with large quantities of inert dust will not form explosive mixtures with air. Pure powdered soap, however, presents a different aspect. Pure soap is formed by combination of alkali (incombustible material) with fatty acid (combustible material). Toilet soap fray also contain a certain amount of glycerin and essential oil winch, being combustible influence the explosibility]

Jan 1, 1928

By W. R. Reed, J. A. Organiscak

Surface mining operations use large off-road haul trucks extensively to move material at mining properties. Past research, using the United States Environmental Protection Agency’s (EPA) emissions factors for unpaved haul roads, has shown that haul trucks generate the majority of dust emissions from surface mining sites, accounting for approximately 78%-97% of total dust emissions. Observations of dust emissions from haul trucks show that if the dust emissions are uncontrolled, they can be a safety hazard by impairing the operator’s visibility. This increases the probability for haul truck accidents (See photos above). However, the greatest long-term health hazard of dust generated from hauling operations is due to inhalation of the respirable dust [median diameter <4 micrometers (µm)] and tho­racic dust, which is equivalent to the EPA’s definition of PM10 [particulate matter with a median diameter <10 µm]. Exposure to respirable dust has long been considered a health hazard at surface mining operations, especially if silica dust is present. There are two legislative acts that regulate the air quality for mining operations: the Federal Coal Mine Health and Safety Act of 1969 and the Clean Air Act of 1970. The Federal Coal Mine Health and Safety Act of 1969 established the limits for dust in the work place for health and safety pur­poses. The Clean Air Act of 1970 regulates air emissions from facilities from an envi­ronmental perspective.

By A. M. Dale, J. Standeven, B. Evanoff

Tool manufacturers continue to incorporate new designs to the internal mechanism of tools in order to decrease the vibration that is delivered to the hand during operation. Modification of some tools to minimize tool vibration is not easily resolved through internal tool design. For this reason, vibration damping materials applied between the tool and the hand are a simple alternative. The damping materials may be applied to the area of the tool directly contacted by the operator or in a glove containing a vibration absorbing pad. These interventions are developed specifically to damp vibration but are not necessarily produced and tested under the same work conditions that a company may expose their workers. Therefore, it is important to test the value of the proposed interventions for the specific applications. This study evaluates the effectiveness of anti-vibration interventions currently in use at a local manufacturing company. Methods The design of this study evaluates the vibration energy produced at the tool handle and from the back of the operator’s hand. Each operator performed a series of fastener installations in metal using several interventions and one series with no intervention as a control. Four of the interventions were gloves containing anti-vibration material and the fifth intervention was an anti-vibration material wrapped around the tool handle. The protocol for wrapping the tool handle was developed and is part of the equipment procedure at this manufacturing company. Test conditions mimicked production work conditions including similar materials, fasteners and technique for installation. Vibration values were collected using 3 tri-axial accelerometers with one firmly glued to the tool handle close the hand grip as recommended by ISO 5349. A second accelerometer was placed on the top of the pistol shaped tool. The third accelerometer was attached to the back of the hand close to the third knuckle using double sided tape. Results Preliminary results for 3 volunteers show a difference between the vibration values of the control condition (mean hand vibration on bare hand = 1.77 Gs) compared to all of the interventions (p=.0001 using Mixed Procedure, Tests of Fixed Effects). The graph below shows individual trials for each subject for each condition. Glove 3 with the air bladder insert shows large variability between subjects (Range = 0.84-3.33 Gs). The other interventions show much less variability both within subjects and between subjects indicating consistent response with use of the intervention.

Jan 6, 2006

By John C. Edwards

Carbon monoxide (CO) sensors are used in mine fire early-warning systems. Experiments were conducted by the U.S. Bureau of Mines with six diffusion-type CO sensors to determine their response to a reference CO concentration under both static and dynamic flow conditions. Static experiments were conducted with 0.5 L/min flow of 16 ppm CO in N2 through 8-and 12-L chambers. Dynamic flow experiments were conducted in two environmental chambers: One had directional flow capability of 1 m/s, and the second provided moderately nondirectional flow as high as 1.8 m/s. Reference CO concentrations of 13.5 to 19 ppm in air were used for the dynamic experiments. The results of the static experiments demonstrated that the sensors consistently underestimated the reference gas concentration. The dynamic experiment results showed the sensors provided reasonable agreement with the reference gas concentration when directional flow effects were not considered. Directional flow effects were evaluated for two sensors. One of the sensors showed a strong dependence upon the relative orientation of the diffusion tube with respect to flow direction. The second sensor did not show a dependence upon flow direction. The sensors&apos; directional flow effect is significant for their proper in-mine utilization.

Jan 1, 2010

By Joseph Chalmers

Stimulative methods of production, whereby the total recovery of oil from natural reservoirs is increased, have come into considerable prominence during the past 15 years. In many oil-producing areas properties considered ready for abandonment by ordinary producing methods have responded to some form of stimulation, and their economic lives have been extended. The stimulative method having widest application is the injection of air or gas into the reservoir formations through selected input wells and is commonly referred to as the "gas drive." As a result of the many successful "gas-drive" operations operators are depending more and more upon this method for increasing the ultimate recovery of oil from their properties. A number of factors influence the efficacy of different gases as propulsive agents in recovering oil from sands. Gases of high density and viscosity show a tendency toward a slightly higher efficiency than those of lower density and viscosity. The solubility of the gas in the oil also affects the efficiency of oil recovery. Not only does dissolved gas decrease the viscosity of the oil, but dissolved gas that expands from solution in the oil tends to increase the effectiveness of a "gas drive." Interfacial tension between the oil and the gas and its effect upon the recovery of oil by gas injection are factors of which little is known. Dr. A. G. Loomis expressed the opinion that interfacial tension probably plays a minor role in the recovery of oil, except under conditions that produce a gas-oil foam. In connection with the above physical properties that influence the action of a pressure medium, control of the injected volume of the pressure medium is perhaps the major factor. The rate of gas injection determines to a great extent the amount of slippage and the resulting efficiency of the operation. The importance of volume control is realized when one considers that frequently it is the only factor that is under complete control of the operator.

Jan 1, 1930

By Frank E. Chase, John Rusnak, David Newman

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970’s and early 1980’s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A “technical disconnect” had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980’s and 1990’s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more “numerically” to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

By Warren E. Morrison

The continuing high-level performance of the domestic mineral and mineral fuels industries during 1966 was sustained by the longest business upturn in the Nation&apos;s history. Spurred by consumer demand at home and the defense production requirements of the Viet-Nam war, the rising trend of economic activity during the year was reflected in the upward movements of the major economic indicators. At yearend the gross national product (GNP), representing the value of all goods and services produced, stood at $740 billion, $58 billion greater than in 1965. Corrected for price changes, the real value of GNP in terms of 1958 dollars was $648 billion and represented an annual increase in economic activity of 5.4 percent. Some 74 million persons were employed during the year out of a total population of 196.8 million, while unemployment fell below 4 percent. The Federal Reserve Index of Industrial Production averaged 156 for 1966, up 13 points from the previous year. However a jarring note in the 1966 expansion, and one which affected the mineral industries in particular, was the increasing pressure on prices and the threat of inflation. From 1961-65 economic growth was facilitated by relatively stable wages and prices and only mild inflation. During the period average wholesale prices hardly moved while average consumer prices rose only about I percent per year. But this long run of relative price stability ended during 1966 when consumer prices rose 2.9 percent and wholesale prices were up 3.2 percent from the previous year.

Jan 1, 1967

By M. M. Myers

"Importance pf the small stone problem.Profitable disposal of limestone too small for making lime in the shaft kiln, is one of the most urgent problems in the lime industry. Reports received by the Bureau of Mines from 31 quarries show that the proportion of small stone varies from 2 to 40 per cent, averaging 18 per cent of gross pro¬duction, Modern methods of heavy blasting, and the use of crushers in large quarries tend to increase the proportion of small stone above that produced in early days when light blasting and hand sledging were almost universally used. There is also a growing movement toward underground operation of lime deposits, a method which in general produces a greater proportion of fines than is encountered in open-pit work. Thus the small stone problem is of growing importance, and demands the attention of every progressive lime producer. As the problem is of almost universal interest, it is urgently desired that every operator who reads this report will contribute from his knowledge or experience, answers to the questions on the final sheet.There are several markets in which small stone may be sold but in these markets the competition is generally keen and the prices low. The lime producer's chief product is lime, he understands its manufacture and marketing, and brings him a greater return than can be obtained from most limestone by-products. For these reasons it is evident that the conversion of small into lime is the nest desirable means of disposal."

Apr 1, 1924

By Launa Mallett, Charles Vaught, Michael J. Bmick

Since 1991 the Pittsburgh Research Center (PRC formerly part of the U. S. Bureau of Mines) has been tapping u valuable resource-researchers have recorded extensive interviews will, 30 individuals who are recognized as experts in the area of mine emergency response. These veterans related stories and observations from events experienced during as many as 47 years of response activities. Overall, the response veterans averaged 29 years of mine emergency response experience and 35 years mining experience. Individuals [ ] interviewed included representatives from mining companies, the UMWA and state and federal government agencies. This information was gathered so dial it could he provided to today&apos;s miners and to tomorrow&apos;s emergency response personnel. It is hoped the collective wisdom that has been obtained can be used to help train new responders and guide those decisions which mill have to be made on the scenes of future events. During interviews file emergency response experts were asked to discuss lessons they had learned through experience. The interviewers asked them to tell what they had learned that would cause them to handle similar situations differently and to tell about things they saw at past events shat the would warn others not to do in the future. In response the experts discussed a variety of things. Most of their responses, however, touched on some of the same topics including: preparedness, experience people on-site mine rescue teams, and decision making. A summary of their responses provides alt overview of [lie lessons learned on-site at tile largest mine disasters in the country.

By Joseph Chalmers

[Stimulative methods of production, whereby the total recovery of oil from natural reservoirs is increased, have come into considerable prominence during the past 15 years. In many oil-producing areas properties considered ready for abandonment by ordinary producing methods have responded to some form of stimulation, and their economic lives have been extended. The stimulative method having widest application is the injection of air or gas into the reservoir formations through selected input wells and is commonly referred to as the ?gas drive." As a result of the many successful "gas-drive" operations operators are depending more and more upon this method for increasing the ulti¬mate recovery of oil from their properties. A number of factors influence the efficiency of different gases as propulsive agents in recovering oil from sands. Gases of high density and viscosity shrew a tendency toward a slightly higher efficiency than those of lower density and viscosity. The solubility of the gas in the oil also affects the efficiency of oil recovery. Not only does dissolved gas decrease the viscosity of the oil, but dissolved gas that expands from solution in the oil tends to increase the effectiveness of a "gas drive." Interfacial tension between the oil and the gas and its effect upon the recovery of oil by gas injection are factors of which little is known. Dr. A. G. Loomis5 expressed the opinion that interfacial tension probably plays a minor role in the recovery of oil, except under conditions that produce a gas-oil foam. In connection with the above physical properties that influence the action of a pressure medium, control of the injected volume of the pressure medium is perhaps the major factor. The rate ofg;as injection determines to a great extent the amount of slippage and the resulting efficiency of the operation. The importance of volume control is realized when one considers that frequently it is the only factor that is under complete control of the operator.]

Jan 1, 1930

By C. V. Davis

In the lnvestlg::ìt1on of mAthods for aSS8.7ing platin",. conducted by the Bureau ot MinAs, reoent experiments have d~velopad tha~ with ce..tain orei, especially when thr, quantity Of platinum 1s eonlidarablfl, nit'!le acid w111 not etfßct a iepard-Han of platinum and pa11adium. 'lhe following m;lthod has been found to be accurate and to reiu1 t in a complete S''lun''ation of' th~3:l metals. It is therefo 1" '!eeommei:ed that 1 t ba followed rath::r- than the method of separation with nitrio acid, givèn in Technical Pape'! 270.* At line 22, pagi 14, of that paper, bAglnnlng with ~tarm th,~ metals '.'ith dilute¡ nitrio acid," strikE out the rest of the paragraph, and substttutt~ the pro_t cedure g1 ven below. ?lunder and Thuringer.. have developed mnt¡iods for th"i sflparation of palladium from all the platinum metals exoept platinum bj m ,ans of dlmethy- 19lyoxlme. They state that the~ is no action for several hours if an excess of dimeth¡lglyoxime is added to an aqueous solution of ohloroplatinic acid in the cold, alio that only on boiling is the platinum pTecipi ated ¡~d than only PST't of the platinum i srenoved from the sUut1on. They found that palladium 1s p~ecipi tated quati tat! vely in the oold as (CaH 4N40 Pd) which is insoluble tn water, dilute hydroohlorio acid, dilute acetIc aofd or in 50~ ethyl alcbhol. All of their pT'90ipi tations we~p Carl". ied out ~hile the solutions were being heated. This caused a pal"tia~recipltation of the platinum along wi th the

May 1, 1922

By Harry E. Tufft

Data were obtained by the writer from a number of the large coul-mine operators in Illinois, on the consumption and cost of timber used in their mines and the quality of the timber now being used as compared with former years. This information supplemented by comparative date for previous years published in bulletins of the filinois Coal Mining Investigation series, and other sources, is presented below. This survey is part of a cooperative study with the . S. Forest Service, of the mine timber situation, with particular regard to the economies to be derived by better selection, preparation, and storage of timber, and especially treatment with preservatives to prolong the life. Geo. S. Rice, chief mining engineer of the J. S. Bureau of Mines, under whose general direction the work was done, gave valuable advice and criticism. R. B. Miller, State Forester, contributed helpful data which he had recent- ly obtained in an independent study of the mine-timber situation in Illinois.

Apr 1, 1923

By Alla D. Mah

Thermodynamic calculations for antimony and its compounds have been hampered by the lack of adequate basic thermal data; much work rains even to fill the more important gaps. This paper supplies heat and free energy of formation values at 298.15° K, for the sesquioxide and tetroxide, based upon new measurements conducted by the Bureau of Mines. The heats of formation were obtained by combustion (bomb) calorimetry, and the free energies of formation were obtained by combination of heat and entropy data. The new values are believed to substantially improve the accuracy of thermodynsunic considerations involving these oxides.

Jan 1, 1962