Search Documents

By Robert J. Timko

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has re- searched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world, and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1986

By J. B. Zadra, S. M. Shelton, M. M. Fine

"Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well known that there are large deposits of low-grade ore in the United States, the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to procure adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigation designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines.This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that woo set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3606, Manganese Investigations. 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. R. Schack. Other reports will be published as the work progresses."

Mar 1, 1942

By H. E. Powell

Because of increasing consumption of high-and super-duty refractories, the Bureau is studying the feasibility of beneficiating submarginal and marginal clays. Diverse mineral dressing tests were used to beneficiate samples from the east-central Missouri fire clay district. Standard ASTM tests were used to determine refractory properties of both crude and beneficiated clay samples. Marginal and submarginal clays containing impurities were effectively beneficiated by both wet-cyclone and wet-table treatment, but the wet-cyclone treatment was cheaper. Ion-exchange resins in the hydrogen form will probably prove more effective in removing potassium, the only alkali in Missouri fire clays to be a problem. Resins with greater cross linkage are more effective than resins with less. Roasting the crude clays before removing alkalis by chemical leaching was ineffective. By applying ultrasonic energy at a frequency of 10 to 25 kilocycles to aqueous suspensions of the clays, subsequent ion-exchange extraction of potassium was slightly improved. Higher frequency ranges did not help.

Jan 1, 1963

By A. R. Taylor

Using solution calorimetry, the following heats of reaction were determined: (1) NaCN(c) + 1/Cu20(c) + 129H20(l) ? CuCN(c) + NaOH?128.5H2O ?H = -13.44±0.10 kcal/mole, (2) HCN(2) + NaOH?128.5H20 ? NaCN(c) + 129.5H20(l) ? = -2.52±0.02 kcal/mole. From these reactions, the heats of formation for CuCN(c) and HCN(2) were calculated to be 22.7±0.4 kcal/mole and 24.9±0.4 kcal/mole, respectively. Reaction 2 was made to check the consistency of literature values for heats of formation of HCN and NaCN. Adiabatic calorimetric measurements between 10° and 400° K showed the entropy and heat capacity of CuCN(c) to be 21.51±0.06 eu and 14.58±0.04 cal/mole deg, respectively, at 298° K. A broad anomaly in the heat capacity was found in the temperature range 285°-320° K. The heat of transition associated with this anomaly was less than 1 cal/mole, the sensitivity of the measurements.

Jan 1, 1971

By H. P. Greenwald, G. E. McElrey

"Part IV.- The Resistance Caused by Right-Angle Bends. IntroductionThis paper deals with the fourth phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the major results public as rapidly as possible. Parts I, II and III were issued as Serials Nos. 2621 (July 1924), 2647 (October 1904) and 2671 (March 1925) and dealt with the resistance of unobstructed entries, the resistance due to mine cars and, the resistance of timbered entries respectively.Description of the Tests With the last cutthrough between the two butt entries of the test section in the Experimental Mine open, the air flow was deflected, around two right-angle bends in the same direction, the butt entries being 50 feet center to center and approximately 6 by 9 feet in cross section. Each bend had a dead end opening off of it; that at the first bend was in the direction of flow and that at the second bond was at right angles to the flow. For a primary test condition the inner corner of each bend was trimmed square and the dead ends were closed off with board brattices set flush with the line of the cut-through.The two corners of the first band were, then modified both independently and in conjunction. Various modifications of both bends in conjunction were also tested with rather surprising results as to the effect of conditions at the first bend, upon the pressure losses at the second. To confirm the theory developed to fit these results a series of tests were made to give a direct comparison of the -pressure losses as between two bends with the air flow deflected in the some direction at each and with the air flow deflected in opposite directions. The former is designated ""double"" and the latter a ""reversed"" right-angle bend. This series of tests was conducted, however, on the bends at one of the intermediate cutthroughs at which the flow could be deflected us either direction at the second, bend. Here also the average cross-section was 6 by 9 feet and the bends were 50 feet apart."

Jan 1, 1928

By L. G. Marsh

The manufacture of lubricating oils from wax-bearing crude petroleums involves the removal and recovery of the paraffin wax contained in the lubricating distillates. During this process several intermediate products are formed, among them the mixture of waxes and oils known to the refiners as "foots oil." Because of its complex character, foots oil is little understood, and therefore methods of handling it in refineries are often inefficient. The Bureau of Mines is studying the manufacture of lubricating oils, and during the work has investigated the redistillation of foots oil. This report gives in brief the results of the investigation, and recommendations based upon it.

Jan 1, 1926

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

Decrease dust concentra¬tions of longwall face workers by keeping them up¬wind of the headgate stage loader and crusher. Approach Direct the face airflow from tailgate-to-headgate, the direction of coal transport. How It Works Ventilation is the primary method of dust control on longwall faces, and the most effective ventilation control is to put workers upwind of dust sources. Recent ad¬vances in longwall dust sampling by the Bureau have shown that on some faces, the headgate crusher and transfer points are signifi¬cant sources of dust -some¬times making up more than half of the total dust to which the face workers are exposed. Also, when the air is coursed from head-to-tail, the relative velocity between the air and moving coal on the face conveyor can cause dust entrainment from the conveyor, particularly if the coal is dry. On the faces where these dust sources are a signifi¬cant problem, they may be eliminated by coursing the air from tailgate-to-headgate, provided that the mine roof is stable enough to permit the necessary intake of the tailgate along with an aux¬iliary intake at the headgate.

Jan 1, 1982

By S. J. Page, J. A. Organiscak

Dust surveys were conducted around small truck-mounted rock drills operating at surface coal mines to assess their airborne respirable dust generation and in-service dust control methods. Of four out of seven drills sampled, respirable dust concentrations measured around the drill deck ranged from 8.68 to 95.15 mg/m with3concentrations ranging from 1.37 to 2.69 mg/m at distances 12.2 to 30.5 m downwind of these drills. The other3drills had noticeably lower respirable dust concentrations measured around the drill deck at or below 1.30 mg/m.3Rotoclone-type dry dust collectors were commonly used with dust being emitted from around the drill deck shroud, collector exhaust, and collector fines dumping. Wind speed and direction was also a factor in the dust concentrations measured on the bench. Dust control modifications were made to three rock drills to reduce their airborne dust emissions. Dust controls tested included water injection into the Rotoclone exhaust, Rotoclone exhaust extension, improved sealing of drilling deck shroud, shrouding the Rotoclone hopper dump process, and wet drilling. These control techniques showed noticeable improvement in dust concentrations measured around the drills. Finally, repositioning the drill operator showed that operator dust exposure can be improved by avoiding the dust cloud around the drill.

Jan 1, 1995

By Walter W. Fisher

A kinetic investigation of copper cementation in a revolving drum was undertaken by the Bureau of Mines to explore the effects of a porous copper deposit attached to the iron surface and a fluidized slurry of copper particles surrounding the iron precipitant. The rate of cementation was found to be significantly enhanced by the increased cathodic areas provided by a porous copper deposit or the presence of a fluidized bed of copper particles contacting the iron precipitant. The cementation rate was found to be retarded by increased ionic strength, low pH, and the presence of oxygen. The cementation reaction was first order with respect to precipitant surface area. Copper cementation on iron is visualized to occur by two basic mechanisms. Precipitation may occur through a series of shorted electrochemical cells, whereby cupric ion precipitates on a growing cathodic copper deposit, or, deposition may occur via a fluidized cathode of copper particles contacting the ion precipitant.

Jan 1, 1976

By Ann G. Kim

Methane in coal constitutes a serious hazard during mining. Draining the methane from large blocks of coal in advance of mining is an effective method of improving the safety and efficiency of coal mining. Because of the similarity of the two gases, drained methane can be recovered and added to pipeline supplies of natural gas. To effectively apply advance drainage techniques and recover drained gas, a gross estimate of the methane content of coal is necessary. Using data from previous investigations, the virgin reserves of the Pittsburgh coal in the central and southwestern parts of Washington County, Pa., are estimated at over 1.5 billion tons, with a methane content of 50 to 100 fts/ton. The Pittsburgh bed in this area of approximately 265 mi2 contains over 130 billion ft3 of methane.

Jan 1, 1974

By Daryl E. Radcliffe

Ninety-seven roof bolts were instrumented with strain gages and resin-grouted in three areas of the Bear coal mine, Somerset, Colo., by the Bureau of Mines. Measurements taken with these instruments indicate roof support is achieved through a combination of point suspension and resistance to vertical and horizontal stresses caused by localized shearing in the roof. The localized shearing results in bending of the bolts, yielding due to high vertical stresses, and the transfer of high loads to the bolt head or plate.

Jan 1, 1980

By Ben A. Kornhauser

The mineral industry consisted primarily of natural gas production and of urea fertilizer, which was manufactured for domestic agriculture. Copper and iron deposits were being developed. Information regarding the mineral industry of Afghanistan was sparse. The Government continued to emphasize the development of mineral resources that could benefit the economy of the U.S.S.R. and repay Soviet grants. The northern half of the country, north of the Hindu Kush mountain range and adjacent to the U.S.S.R., received considerable Soviet aid to develop mineral resources.

Jan 1, 1986

By Tony Keller, Setsuo Maeda

Hand-Arm Vibration Syndrome (HAVS) was identified as early as 1918 in Bedford, Indiana in the U.S. Since then much research work has been done around the world in the areas of medical, epidemiological, engineering and legal aspects of HAVS. In Japan, much of the pioneering work in this field has been performed by Dr. Setsuo Maeda and his staff at the National Institute of Industrial Health (NIIH) in Kawasaki. Most recently, reports of work done by this group and by Dr. Ren Dong1 of NIOSH in the U.S., as well as many other suppliers and Japanese practitioners were presented at the 13th Japan Group Meeting on Human Response to Vibration held in Osaka2 during August 3-5, 2005. [ ]

Jan 6, 2006

By Robert F. Holub

The Bureau of Mines has made a study of the magnitude of the variations of radon daughter mixtures, with the objective of determining whether these variations reflect the existing physical conditions in uranium mine atmospheres or if they are merely random or systematic errors. To accomplish this, many data have been plotted using a triangular graphing technique which shows that plateout affects RaA more than RaB or RaC, and that it is impossible to find simple correlations between working level ratios, radon daughter mixtures, and age.

Jan 1, 1978

By Ruth A. Holmes

A Bureau of Mines method for recovering nickel, cobalt, and copper from low-grade domestic laterites is described, which includes the unit operations of solvent extraction and electrowinning. Previous Bureau work indicated that addition of Na2S04 (sodium sulfate) to the nickel electrolyte improved current efficiency in nickel electrowinning. The present study determines the compatibility of Na2S04 with nickel strip-ping in the solvent extraction operation of the Bureau method. The effect of adding 100 g/l Na2S04 on nickel stripping, phase disengagement, and pH was determined in comparative laboratory-scale tests. In continuous-circuit testing, Na2S04 reduced stripping efficiency to the extent that five, instead of four, strip stages were required for complete stripping of nickel from the loaded solvent. In tests made in a phase-disengagement cell that had a variable settler area, the addition of Na2S04 did not significantly affect phase separation characteristics. The pH of the nickel electrolyte in the temperature range of 20° to 65° C was also unaffected by the addition of Na2S04. An economic evaluation showed that the energy saved by adding Na2S04 to the electrolyte would more than offset the cost of adding another stripping stage.

Jan 1, 1983

By S. J. Davenport

[The tremendous increase in mine mechanization since 1929 has increased markedly the application of electric power in and about the coal mines of the United States. Cutting, drilling, and leading machines have replaced hand-mining methods in nary mines. As a result, expansion of the gathering haulage has necessitated introduction of extensive feeder, trolley, grid other power wires. (1)3/ In spite of this vast mechanization the fatality rate from electric shock has been on the decline. However, there are still too many accidents, and efforts to eliminate electrical hazards cannot be relaxed. It is hoped that an acquaintance with the physiological aspects of electrical accidents will make workers end management aware of the lurking dangers of this very common and extremely dangerous form of energy.]

Jan 1, 1951

By J. C. Kerkering

The Bureau of Mines used mathematical reliability theory to define, for use in the mining industry, the concepts of risk, safety, reliability, hazard, and mean time between accidents. In this report, the definitions are explained theoretically and illustrated by application to actual underground mine accident data extending over a 9-1/2-year period. The theoretical development proceeds along two parallel analytical paths. For each line of reasoning, the data are presumed to be independent. If they are not, the analysis stops, although there are interesting implications when dependency is demonstrated. The first method uses the elapsed times between accidents as the basic data. These elapsed times are fitted to a negative exponential distribution function using least squares and yielding the function parameter, P1 The P1 is used to form the Poisson distribution function for the data, which is then used to define the safety-related concepts. The second method uses the maximum likelihood estimator to formulate a Poisson distribution function for the data. The function is tested for adequacy by a goodness-of-fit test; if the fit is acceptable, the Poison function is used to define the concepts. Both methods were applied to the data base, yielding nearly identical results.

Jan 1, 1987

Reliably detect fires by sensing sub-micrometer-sized particles released into the air by smoldering or burning materials. Approach An extremely sensitive, ionization-type fire detector has been built that continuously draws air samples through its ionizing field and collects the ionized smoke particles downstream, thereby generating a proportional electrical output signal. (An offshoot instrument measures the size distribution and number of sub-micrometer particles in air.) How It Works Mine air to be monitored is drawn through the instrument assembly by a small pump. A pre-filter and cyclone remove dust particles and other particles larger than 0.6 micrometer diameter. The air and remaining aerosol-sized particles flow through a gastight tube which contains the detector. See diagram. Smoke and other sub-micrometer-size particles moving Into the detector, pass through an Ionizing field, and are struck by alpha particles released from radioactive source located on the axis of the tube, The alpha particles move radially outward until they strike smoke particles or molecules of air or water. When struck, a smoke particle or molecule loses an electron and becomes positively ionized.

Jan 1, 1979

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969