Search Documents

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

By R. V. Ramani, V. T. Burgos, J. A. McClay

Introduction The Cost program was developed to provide the planning engineer with a tool to evaluate the cost implications of the technical mine design decisions. Direct costing methods are employed, where feasible, to provide greater detail and accuracy in the primary cost centers. Options have been provided in the cost computation, economic analysis, and output data subsystems to increase the flexibility of the system. Computer Program The program is written in Fortran IV for use in the IBM System 360/370 computers. i. Main - The main routine reads and stores input data from three sources, user input, Cost Data Library, and data transfer from the Master Design Simulator. Data is trans¬ferred to the appropriate subroutines, as they are called, by means of labeled common blocks. ii. Subroutine CSTCOM - is a data modification routine which computes the peripheral charges related to labor and supervisory costs. iii. Subroutine MANPWR - interrogates section data to determine the total labor and supervisory costs for each cost center. iv. Subroutine CAPCST - computes the total capital investment for each cost center, including the economic life and salvage value of each element. Capital costs are determined by user selection of quantities and models of equipment. Equipment costs are stored in the Cost Data Library for retriev-

Jan 1, 1975

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

By Elaine T. Cullen

Educating the public about the role of mining and minerals can be a challenge. While it sometimes seems that little is being done to counteract negative publicity, there are many exciting things happening across the country that are helping meet this challenge. This paper will discuss existing minerals education activities and will provide tips for developing successful programs for a variety of groups, from students to industry to minerals educators themselves. The paper will also include an overview of the 9th annual National Minerals Education Conference held in July 2000 in Spokane, WA.

By H. E. Hilliard

The Bureau of Mines investigated hydrometallurgical procedures for concentrating precious metals from a mechanically processed metal fraction of obsolete military electronic scrap. Feed material for the leaching procedures described in this report was the high-tension-separated metal concentrate obtained as a fraction from mechanically processing partially stripped electronic units. Initial pretreatment with a 20-wt-pct-NaOH solution solubilized most of the aluminum. After washing, the resulting residue was incinerated to destroy any organics attached to metal particles. The incinerated residue was leached with 20-vol-pct H2S04 solution using two methods, countercurrent pressure and ultrasonic-aided leaching to solubilize the base metals, predominantly copper. Silver was recovered from the base metal leach residue using 50-vol-pct HN03, and gold contaminated with several percent palladium was recovered from the silver leach residue using aqua regia. The impure silver and gold plus palladium products represent about 1.5 wt pct of the high-tension-separated metal concentrate. Included is a three-step process evaluation study of mechanical processing of general electronic scrap and two hydrometallurgical procedures for leaching high-tension-separated metallic concentrates obtained from the mechanical processing step. Process evaluation concluded that only mechanical processing is economically viable.

Jan 1, 1985

By R. R. Sayars

"Carbon monoxide is a gas slightly lighter than air, with which it diffuses readily to make a homogeneous mixture. It will burn and has a wide explosive range, that is, an explosion is possible when the air contains from 15 to 73 per cent of the gas3. This explosive range is about the same as that for hydrogen and over nine times As Tide as that for marsh gas (methane). Like air, it has neither color nor taste and has no odor in concentrations usually encountered, therefore it cannot be detected by the ordinary senses with which men are endowed. It is produced by burning carbon containing fuels, no coal, wood, gasoline, etc., whenever not enough air or oxygen is supplied to burn and oxidize the fuel completely.The human race has probably been exposed to this gas since men first began using fires in confined or sheltered places. The poisoning as usually encountered is an acute condition resulting from breathing atmospheres con¬taining this gas. A number of eases described in the ancient literature Indicate that carbon monoxide was a frequent cause of death by accident, suicide and is a means of punishment or torture. A quotation by Lewin from Aristotle who lived in 384-322 B.C., states that ""animals collapse from harmful odors as men gets a severe headache and often dies through charcoal vapors"". The Roman knew that smoke was poisonous, and used the greenest most smoke-producing wood to put persons to death. The occurrence of carbon monoxide increased in frequency through the years until at the present time it is found in the home as well as in many industries. The following table gives the approximate percentage of carbon monoxide found in gases from various sources of poisoning.4"

Apr 1, 1924

By Gerald T. Homce

A system capable of monitoring a mine electrical power system to detect incipient electrical component failure could significantly improve power system safety and availability. The U.S. Bureau of Mines funded a contract with The Pennsylvania State University (Penn State) to establish the theoretical and technical framework for such a system. This report briefly outlines the contract, reviewing related Bureau and Penn State work prior to its award, and describes support work carried out by the Bureau. The main focus of the report is on research efforts by Penn State and subsequent results. An existing algorithm for incipient-failure detection and classification was studied, and recommendations are made to improve its performance. In addition, mathematical models of cable-connected motor systems and deteriorating motors were developed and implemented on computers. These models and laboratory tests were used to study and document relationships between component deterioration and electrical terminal effects. The project was supported by the U.S. Navy and the nature of its interest in the application of failure prediction techniques is also included.

Jan 1, 1989

By Robert J. Evans

Capital and operating costs were estimated using a wet suppression, fabric filter, and a combination system of the two for hypothetical hard rock stone crushing plants located in central Pennsylvania, operating at 300, 600, and 1,000 tons per hour. Fixed capital expenditure for the dust abatement systems ranged from $49,129 to $249,162. Annual operating costs for the dust abatement systems ranged from $8,394 to $46,606 (0.9 to 3.2 cents per ton). If these dust abatement systems are properly sized, installed, and maintained, efficiencies approaching 95 percent can be expected for reduction in weight of dust particles emitted before control.

Jan 1, 1975

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993

By Paul J. Barrett

The Bureau of Mines evaluated a sulfurous acid-sulfuric acid process for recovering alumina from clay, in which clay is leached. successively with sulfurous acid and sulfuric acid. The resulting aluminum sulfite and aluminum sulfate solutions are combined and heated to produce a basic aluminum sulfate and sulfur dioxide. Alumina is extracted from the basic aluminum sulfate as sodium aluminate by leaching with dilute sodium hydroxide. After desilication, sulfuric acid is used to precipitate alumina as alumina trihydrate, which is then calcined to alpha-alumina. The estimated fixed capital cost for a plant producing 1,000 tons per day of alumina is about $74 million on a 1971 basis. For comparison with previous alumina-from-clay evaluations, the estimated fixed capital cost for the plant is about $67 million on an M and S Chemical Equipment Index basis of 24.0.0, which is equivalent to a 1960 cost level. Because the operating cost is highly dependent on fuel and electric power costs, graphs are included to show the effect of these items on the operating cost. On a 1971 basis, with natural gas costing 35 cents per million Btu and operating labor costing $4 per hour, the estimated operating cost is about $100 per ton of alumina. On a 1960 basis, with labor costing $2.30 per hour and natural gas costing 25 cents per million Btu, the estimated operating cost is about $86 per ton of alumina.

Jan 1, 1973

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By John Millhiser, Margaret Bonarek, Dennis McLaughlin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine's Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested and demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

By Oliver Bowles

Granites are classed as igneous rocks ; they have been formed by the solidification of rock magmas or solutions from deep within the earth . It is an almost invariable law of nature that magmas which cool quickly form fine- grained or glassy rocks , while those that cool slowly are completely crystallized and are coarser- grained . Granites , being of the latter class , are regarded as having attained their solid form at considerable depth below the surface under conditions of high temperature and pressure . The constituent minerals crystallized out slowly , the crystals interlocking with one another . The great depth of overlying rocks that must have been present when crystallization took place has been removed by erosion over large areas on the surface of the earth , in consequence of which granites appear at or near the surface in many localities . The chief minerals of which granites are formed are feldspars , quartz , and either mica or hornblende . All the essential constituents except mica are as hard as , or harder than steel , therefore granites are difficult rocks to cut and dress . Granites are usually red , pink , or gray , depending on the color of the feldspars . If hornblende or black mica is abundant the rock may be dark green or almost black . Granites are characterized by massive homogeneous texture . They are classified as fine- grained , medium- grained , or coarse - grained . Medium- grained granites are those in which the feldspar crystals average about one- fourth inch in diameter . If relatively coarsegrained crystals appear in a fine -grained ground mass the rock is designated a porphyritic granite . Uniformity in texture and grain size are desirable in building and ornamental stone , although occasionally rocks of variable texture , such as the porphyritic granites , are used . A rock may have the mineral constituents of a granite but show a banded or platy structure due to recrystallization , folding , or other changes while the rock was in a plastic or semimolten condition . Such metamorphic rocks are called granite gneisses . They are used occasionally for building purposes but not as commonly as the uniformly textured granites . - Granites are named from the most abundant mineral other than quartz and feldspar that they contain , being called , for example , biotite granite or hornblende granite . - Commercially other igneous rocks granitoid in texture but more properly classified as syenites , diorites , or gabbros may be classed as granites . Thus the " black granite " of Little Falls , Minn . , is a diorite , and the " black granite " of Eastern Pennsylvania consists of diabase or gabbro . The question is sometimes raised as to the depth to which a granite occurrence may extend . In this respect granites differ notably from limestones , sandstones , or other sedimentary rocks . The sediments were originally laid down in relatively thin beds , and individual formations providing rock of economic value may be quite limited in thickness . Usually the usable beds range between 40 and 200 feet in thickness . On the other hand , granite comes up from below . Its depth is unknown , but in general is very great . It may even be measurable in miles . The reserves of material at depth are to be measured , therefore , by the economic depth of working rather than by the vertical extent of the rock mass . Exceptionally , granites of commercial quality may occur in sills or sheets of limited thickness flanked on either side by rocks of different character , as , for example , at Westerly , R. I.

May 1, 1930

By Richard F. Hewlett

This report describes a comparison of methods for computing grade and tonnage of ore, leach, and waste material for a mined-out portion of the Silver Bell Oxide porphyry copper deposit, and these computed values are compared with the actual tonnage of these classes of material produced during mining operations. Comparisons with production records have been made by using both exploration drill-hole assays and development blast-hole assays. The polygonal method is the most accurate for this deposit, because it more closely represents the lateral mineral distribution in the deposit. This is demonstrated by plots of the total-copper assay distributions of the development blast-hole assays for a specific bench. The investigation also shows that the smaller vertical assay interval (based on a 5-foot vertical churn-drill-hole sample) yields a more accurate estimate of both grade and tonnage than the 40-foot composite assay interval (based on the average of eight 5-foot assay values). This can be attributed to the fact that selective mining within a bench can separate out much of the waste and leach material that is included as ore in the 40-foot composite assay computations.

Jan 1, 1970

By Lorenz E. Sieffert, Lawrence B. Berger, H. H. Sehrenk, Ralph W. Stewar, James A. Gale

"INTRODUCTION The purpose of the investigation discussed in this article was to evaluate the toxic hazard from gases produced when thermosetting plastic materials used for electrical insulating purposes are burned or thermally decomposed in enclosed spaces. For brevity the term ""toxicity"" is used throughout the article to refer to the nature of gases produced under these conditions. A need for immediate study of the problem was created as a re¬sult of the battle damage reports received from various United States Fleet units. These indicated that the fumes emitted when these materials were burned or thermally decomposed had, in several instances, resulted in toxic atmospheres. In attempting to develop a suitable test method for evaluating toxicity, it was recognized that no single test procedure could be expected to duplicate the variety of conditions that might exist in an actual fire aboard ship. In view of the immediate need, however, it was felt that considerable information could be obtained, at least to classify comparatively the several types of materials as to the toxic effect caused by burning or thermal decomposition, through the development of a sound empirical method which could be applied to all of the materials. On this basis, it was decided to modify the Navy flame resistance test for thermosetting plastics to render it applicable to the determination of the toxic, gases evolved when this test was employed. A wide variety of materials was tested, both molded and laminated, to cover the types commonly used by the Navy in electrical applications. Toxicity determinations were conducted at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Parallel tests, to determine the flame resistance of the materials, were conducted at the Material Laboratory, U. S. Navy Yard, New York, N. Y."

Oct 1, 1947

By C. J. Cohen, L. A. Dahners

"SUMMARYA method has been developed for surveying, drill holes without lowering into the hole any surveying equipment other than an etch tube. The orientation of the rods at the collar of the hole is maintained as the etch tube is lowered. The attitude of the etch ellipse in depth with respect to the rod orientation at the collar can then be observed. This relationship permits the bearing of the hole in depth to he calculated. The rod orientation is maintained during the lowering by means of a pair of alinement clamps. One clamp is fastened to the top of each rod as the rod is coupled and is removed when the alinement has been transferred to the other clamp at the top of the next succeeding rod. A particular advantage of this survey technique is that surveys can be readily made in magnetic country rock.PRINCIPLE OF THE TECHNIQUEAn axial lamina of the column of drill roes is the lamina in which one fiber would be the centerline of the rods. In the new survey technique, the rods are fed into the hole in such a manner that the axial lamina of each successive rod maintains its position at the collar of the hole. In depth, as the rods bend in following the drill hole, the axial laminae also bend. The lamina that was originally vertical will, in general, be tilted away from the vertical. The trace of this lamina is marked on the glass etch tube before the tube is lowered in the hole. The axial lamina that becomes vertical at the survey station is recognized as that axial lamina which contains the long axis of the etch ellipse. The angle between the lamina originally vertical and the lamina vertical at the survey station is thus measurable. When the vertical axial lamina at one survey station has been determined by the etch ellipse at that station, angle R between this lamina and the vertical axial lamina at the next survey station becomes measurable also. By moans of angle R, and dip angles D1 and D2 at the two stations, the change in bearing (z) of the drill hole between the two stations can be calculated."

Aug 1, 1944

By R. O. Dannenberg

This report describes aperiments by the Bureau of Mines and reviews theoretical aspects of the use of organophosphate solvent extraction for recovering beryllium from sulfate leach liquors. The leach liquors were prepared by sulfuric acid leaching of lime-sintered low-tenor beryl flotation concentrates. The experimental work on sulfate leach liquors showed that the acidic esters of organophosphates extracted beryllium slowly but in preference to aluminum. Three common alkylphosphoric acids, di- (2-ethylhexyl) (EHPA), heptadecyl (HDPA), and dodecyl (DDPA), in order of decrmsing selectivity, yielded a partial separation of beryllium from aluminum.

Jan 1, 1962

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines(USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two formulations resulted in stable gels that lasted for at least 12 months in the mine. Semi continuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both interms of productivity and enhanced mine safety.

Jan 1, 1995

By Thomas A. Morgan, Louis A. Panek

This report describes a method for determining the stress in rock based on a requirement for static equilibrium ; namely , that the total load on a sufficiently large area must remain constant even after a drift or stope is mined in the area . The method is based on mathematical relationships that are independent of the elastic properties of the rock and the stress distribution near the underground opening . In addition to determining the preexisting stress (before mining ) , the method described can be used to determine the change in stress due to mining .

Jan 1, 1963

By J. R. Long

The investigations described herein are concerned with a portion of a systematic research, by the Federal Bureau of Mines on ductile titanium. The Bureau's work on the metal has resulted in development of a semi commercial process for the preparation of titanium and has also made available significant information on the fabrication and physical properties of this new strong, light, corrosion-resistant metal. Considerable interest has been aroused by this work, and a number of other laboratories have begun similar investigations. However, the necessity for Consolidating titanium by normal powder metallurgy methods presents difficulties in producing commercial forms and shapes on a large scale. This investigation was therefore undertaken for the purpose of improving the technique for consolidation of titanium powder into solid nonporous metal.

Jan 1, 1949