Search Documents

This volume summarizes the contract work performed over a nine-month period by Westinghouse Electric Corporation on a Cost Plus Fixed Fee Contract for the Department of Interior's Bureau of Mines. The contract has been extended primarily to carry out improvements recommended for equipment produced under the contract for communicating with and locating trapped miners. These improvements will enhance the performance and utility of this equipment for operational use in actual mine emergencies. An additional complete set of the equipment will also he furnished to the Bureau under this extension. The work of the basic contract was to design, produce and test hardware in accordance with the Westinghouse response to a Bureau of Mines Request for Proposal which was based technically on recommendations of a study performed for the Bureau by the National Academy of Engineering (NAE). The NAE study made suggestions for new equipment in three areas of need:

Jan 1, 1971

By Guy A. Johnson

Despite the use of warning alarms to alert miners to the backward movement of large mining equipment, miners still are injured too frequently in backup accidents. Currently approved backup alarm technology consists of continuous sounding alarm systems. New technology has developed a warning system that initiates an alarm only if there is an object close behind the vehicle. This advancement eliminates constant exposure to the alarm because a warning is given only in case of a potential collision. Adoption of this development can improve safety and reduce damage, especially for front-end loaders (FEL's). It will also eliminate a source of nuisance noise in urban and residential areas. This Bureau of Mines report describes the general characteristics of infrared (IR) light, ultrasonic wave, and Doppler radar technology as used for backup alarms, and reviews the testing of the most promising detection devices.

Jan 1, 1986

"Introduction.The Bureau of Mines has taken up the problem of determining a method or methods whereby underground compensation insurance rates for metal-mining companies can be equalized in proportion to the underground hazards involved. This study has been started by the writer with the assistance of Mr. I. M. Wolfin* as consultant.The present paper briefly reviews the origin of accident compensation, gives a digest of State compensation laws, and describes types of insurance carriers. This will be followed by study of the basis of premium rate, risk differentials, and cost of compensation insurance to mine operators. These data will be supplemented by an analysis of the accident hazards in different mining methods and practices, and the severity and frequency of accidents classified by time lost and period of exposure to hazard, for different States, mining methods, occupations and nationalities. Attention will be given to standardized preventives for underground accidents in metal mines, and, finally, the classification of underground metal-mining hazard for workmen's compensation insurance premium rating."

Mar 1, 1924

By D. C. Fleck

The Bureau of Mines, in a cooperative research program with four lead companies, has investigated ferric chloride leaching of galena to prepare lead chloride for molten-salt electrowinning to produce lead metal. The hydrometallurgical-electrolytic process is an alternative to the sintering-smelting-refining process currently used to produce lead metal and avoids the environmental problems associated with a conventional smelter. During investigations on the electrowinning aspects of the work, it was noted that certain cations, moisture, and sulfate in the electrolyte affect lead metal purity, cell voltage, current efficiency, and viscosity of the electrolyte. Results of bench-scale tests are re-ported on the effects of CaCI2, CuCI2, FeCI2, MgCI2, NaCI, ZnCI2, PbS04, and moisture on electrolysis. As impurities increased in the electrolyte, current efficiency decreased. CaCI2, CuCI2, and FeC12 decreased current efficiency by 12 to 47 pct. ZnCl2 gave a small voltage increase, while CaCI2 addition equivalent to 4.9 pct Ca caused a 50-pet increase in voltage. The lead metal was contaminated in direct proportion to the CuCI2 buildup in the electrolyte, Anode corrosion was observed with MgCI2 and MgC12?6H20. Viscosity increased appreciably with the buildup of NaCI, CaCI2, and sulfate. Electrolyte foaming occurred with ZnC12, MgC12?6H20, MgC12, FeC12?2H20, and FeCI2. Moisture inhibited the coalescence of the lead metal.

Jan 1, 1983

By J. Croeni

The search for new alloys for application in the atomic energy field had prompted investigation of zirconium-rare earth metal alloys by the Federal Bureau of Mines. In this instance the zirconium-dysprosium system was investigated by melting point, thermal analysis, resistivity, X-ray and metallographic methods. Results indicate a single eutectic system with a peritectoid reaction occurring at 890° C. The eutectic isotherm extends from 30 to 95-percent dysprosium at 1,280° C. Eutectic composition is located at approximately 70 percent dysprosium. Solid solubility of dysprosium in both alpha and beta zirconium is extensive. The extent of solid solubility of zirconium in dysprosium has not been determined. Although zirconium rich alloys exhibit a significant increase in hardness, they can be cold worked extensively. These alloys also appear adaptable to solution heat treatment. Additional investigations concerning corrosion resistance and other mechanical properties are necessary for satisfactory evaluation of these alloys. The superior corrosion resistance of zirconium and the nuclear cross-section characteristics of the rare earth metals have stimulated alloy investigations using zirconium as a base metal. Alloys combining these characteristics present a possible substitute for hafnium as a control rod material. In this particular study dysprosium was chosen as the alloying element, and several series of alloys were used to establish the equilibrium diagram.

Jan 1, 1960

By Nicholas Kyriazi

Significant portions of the present Federal regulations for certification of closed-circuit breathing apparatus (42 CFR 84) are not quantitative. The human-subject testing portion of the regulations specifies activities rather than metabolic work rates; however, heavy human subjects have higher oxygen consumption, CO2 production, and ventilation rates than lighter human subjects performing the same activities. This means that apparatus certified using different human subjects have effectively passed different tests. In addition, apparatus performance is monitored only during selected intervals of testing, and always during rest, rather than during the entire performance period. Further, testing is arbitrarily terminated at specific rated durations, leaving unknown the performance during the remaining duration. Duration itself is misleading to users who believe that the apparatus will last a certain time no matter how much they weigh or how hard they work. The actual duration obtained from an apparatus, however, is highly variable, being inversely proportional to the work rate at which it is used. In this report, recommendations are made to (1) replace the present regulations for certification of closed-circuit breathing apparatus with quantitative tests specifying metabolic work rate rather than activity,(2) continuously monitor relevant physiological stressors, (3) continue testing until exhaustion of the oxygen source, and (4) classify closed-circuit breathing apparatus by quantity of usable oxygen, i.e., capacity, rather than by duration. Physiology-based stressor levels are suggested as well.

Jan 1, 1999

By J. D. McLenegan

The purpose of this investigation was to prepare a market survey of the refractories industry in California and Nevada (referred to in subsequent paragraphs as the region), and to determine the degree of self-sufficiency and the potential capacity for anticipated growth. The report includes estimates of the total annual refractories consumption, the quantity of refractories imported into the region, the tonnage of raw materials required for their manufacture, and the resources of fire clay and high-alumina minerals in the region.

Jan 1, 1956

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By R. C. Ellman

Significant effects of in-the-mill drying on the pulverization of lignite have been demonstrated in an experimental impact-type pulverizer by tests in which the primary variable was temperature of the sweeping gas. Reduced power requirements and increased product fineness were observed as the extent of drying was increased. Pulverization with in-the-mill drying was studied in comparative tests made on lignites from five mine sources. All of the lignites responded in a similar manner; however, differences in the pulverizing characteristics of the individual lignites were significant. For one lignite, the electrical input to the pulverizer driving motor with minimum sweeping-gas temperature was 33.9 kw.-hr. per ton, decreasing to 14.0 kw.-hr. per ton with a sweeping-gas temperature of 658° F.; for another lignite, at comparable operating conditions, the electrical input decreased from 59.1 to 19.0 kw.-hr. per ton. In the first case, the product fineness increased with increasing temperature of sweeping gas from 65.2 to 79.2 percent through a 200-mesh sieve, and in the second case, from b2.7 to 86.9 percent through a 200-mesh sieve.

Jan 1, 1962

By C. L. Klingman

In extracting helium from natural gas at Bureau of Mines helium plants, a continuous analysis of the helium content of inlet and outlet gas streams is required to determine extraction efficiency. An analyzer, using established principles of gas chromatography to effect the analysis, has been developed by the Bureau of Mines to meet this need. It will record the helium content of inlet or discharge gases from helium-extraction plants every five minutes, continuously, without the attendance of an operator. A 25-inch column of activated charcoal is used as a partitioning agent; nitrogen is the carrier gas; and a hot-wire, thermal-conductivity cell is the detector. A 1.0 mv, strip chart indicates the unbalance of the detector cell, Sample size is 0.37 cc, and carrier gas flow rate is 75 cc, per minute. Significant improvements in helium extraction have been demonstrated by using the chromatograph in three helium-extraction plants.

Jan 1, 1961

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By S. H. Lorain

This paper is one of a series on mining and milling method and costs being published by the United States Bureau of Mines. The Golden Messenger mine, operated by the United Gold Mines Corporation, is in the York-Confederate Gulch mining region in Luis and Clark County, Mont., 22 miles northeast of the city limits of Helena and about 1 mile north of the town of York. It is the first operation to exploit successfully the low-grade ores of the York-Confederate Gulch area. The unusual vein structure presents some mining problems that have been solved in ail interesting manner.

Jan 1, 1937

By Irving Hartmann

Several recent ignitions of firedamp - a mixture of methane and air - in American coal mines have been attributed to frictional heating when hard rocks were struck while cutting and drilling coal seams. Although none of these ignitions caused severe explosions, they call attention to a problem that can become increasingly significant as mechanized mining is developed further. The power in and rapid release of energy from high-speed machinery has increased the rates of advance into virgin coal creating many problems. Unforeseen faults and hard mineral inclusions may be encountered; coal brought down in this way is finer in size; more gas is released from the seam; it is frequently more difficult to provide adequate ventilation at the' face; and new roof-support problems must be solved. In particular, continuous mining machines (also known as continuous miners) greatly increase the frequency of contact between cutter bits and minerals. In view of these conditions, it may be expected that more gas ignitions will occur as a result of frictional heating unless the situation is understood and remedial measures are introduced. The problem of frictional heating is not new in coal mining. In Europe, particularly in England, it has been a concern for more than a century. During the last 15 to 20 years frictional ignitions have been a major cuase of explosions in British mines. Explanations for the greater number of such ignitions in England may be the special character of the coal measure strata, the mining methods, the rate of gas emission and possibly its composition, and less effective ventilation near the face. To reduce the ignition hazard, considerable laboratory and field research has been conducted, particularly by the Safety in Mines Research Establishment, Ministry of Fuel and Power of Great Britain. Much of the information presented in this report has been drawn from these studies.

Jan 1, 1955

By Perry G. Cotter

As a portion of a general program for the synthesis of hard materials, a method was sought by which the hardness and density of tungsten carbide (WC)-cobalt compacts could be increased. It was demonstrated by Cotter that these improvements in quality could be made by employing an electric-resistance sintering process in which heat and pressure are applied simultaneously to presintered compacts composed of powdered tungsten carbide and cobalt. This conclusion was based on tests of material prepared by Cotter on welding equipment in use at the U. S. Naval Engineering Experiment Station, Annapolis, Md., and at Rensselaer Polytechnic Institute, Troy, N. Y. Rockwell-hardness tests made at Norris and core-drilling tests made at the Mount Weather Station of the Bureau of Mines indicated that, for some purposes, carbide material made by this process might be superior to the chemically analogous commercial products prepared by ordinary sintering methods. A program to develop optimum conditions for the electric-resistance sintering of tungsten carbide-cobalt compacts was initiated. The program was followed by a systematic evaluation of the hardness and density of compacts prepared by this method along with a series of carbide compacts furnished by various manufacturers. This paper presents a description of the electric-resistance sintering of tungsten carbide-cobalt compacts and the results of comparative physical tests.

Jan 1, 1955

By John Owens, Wayne Howie, Hamid Maleki

After an analysis of the hazards of room-and-pillar retreat mining systems, it became apparent that safety could be significantly improved by considerations of (1) human factors, (2) remotely controlled mobile roof supports (MRS=s), (3) mine layout designs, and (4) ground monitoring systems. Initial studies of the effectiveness of MRS=s focused on their interaction with mine strata and evaluations of suitable measurements for detecting roof stability problems during pillar extraction. These studies indicated that overall stress distributions and strata movement were most influenced by the stiffness of coal-measure rocks and the design of mining layouts. Thus, to improve worker safety, mine layouts should be carefully designed and a pillar extraction method chosen for specific geologic and stress conditions. Pillar failure was often associated with an increase in pressure on the hydraulic gauges of the MRS, and roof failure was often preceded by rapid changes in the rate of roof-floor convergence. These studies led to development of a monitoring system that displays loading rate on an MRS in real time. A major MRS manufacturer cooperated in installing and testing the system on an MRS. New field studies focus on evaluating the performance of the system, measuring roof-floor convergence, and optimizing the safety of MRS operations through proper mine layout design.

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate-mines in various foreign countries. This interpretation of the mining laws of Greece was prepared from information furnished by Ralph B. Curren, American assistant commercial attache, Athens, in reply to a questionnaire of the United States Bureau of Mines, transmitted through the courtesy of the commercial laws division of the Bureau of Foreign and Domestic Commerce. INTRODUCTION In his report,3 Mr. Curren states that the source of his information was the Director of Mines of the Greek Ministry of National Economy and the Mining Code of Greece, which was, compiled from existing laws in 1929,4 and which has since been modified by several acts of Parliament.

Jan 1, 1932

By Oliver Q. Leone

The effect of oxygen content in the anode metal on titanium electrorefining characteristics was studied. Increasing quantities of oxygen in the anode resulted in increased anode scale formation, decreased anode and cathode current efficiencies, lower titanium recovery efficiencies, and higher oxygen content of the cathode products. The titanium electrorefining process performed best when the anodes did not contain more than 0.5 percent oxygen, although anode dissolution was recorded for alloys containing up to 25 percent oxygen. Back emf affords a useful index of an alloy to electrorefining.

Jan 1, 1965

By Hugo E. Camargo

Noise Induced Hearing Loss (NIHL) is the most common occupational disease in the U.S. with devastating consequences particularly in the mining industry. A study conducted by the National Institute for Occupational Safety and Health (NIOSH) revealed that 90% of coal miners have hearing impairment by age 50, compared to only 10% of those not exposed to occupational noise. According to the Mine Safety and Health Administration (MSHA), Continuous Mining Machine (CM) operators account for 30% of workers exposed to noise doses exceeding the Permissible Exposure Level (PEL). This number becomes more dramatic considering that 49% of the total national underground coal production is extracted using these machines. In this context, NIOSH is conducting research to identify and control dominant noise sources in CMs. Previous noise source identification was performed using a Brüel &Kjær (B&K) 1.92-m diameter, 42-microphone phased array. These measurements revealed that the impacts from the conveyor chain onto the tail roller, and the impacts from the conveyor chain onto the upper deck are the dominant noise sources at the tail-section of the CM. The objectives of the work presented in this paper were: 1) To rank the noise radiated by the different sections of the conveyor, and 2) to determine the effect of a urethane-coated tail roller on the noise radiated by the tail-section. This test was conducted using an Acoustical and Vibrations Engineering Consultants (AVEC) 3.5-m diameter, 121-microphone phased array. The results from this new test show that a urethane-coated tail roller yields reductions in the tail-section of 2 to 8 dB in Sound Pressure Level in the frequency range of 1 kHz to 5 kHz. However, integration of the acoustic maps shows that the front-section and mid-section of the conveyor also contain dominant noise sources. Therefore, a urethane-coated tail roller in combination with a chain with urethane-coated flights that reduces the noise sources in the front and mid sections of the conveyor is required toyield a significant noise reduction on the CM operator?s overall exposure. These results show the applicability of phased array technology for low frequency noise source identification.

Jan 1, 2008

By Charles G. Patmon

This paper describing the methods of dredging and treatment of gold-bearing gravels at the Lancha Plana Gold Dredging Co.'s dredge is one of a series of similar papers being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The dredge is located near the Mokelumne River, 12 miles west of San Adreas, Calif.; it is accessible by an improved dirt road from Jackson, which is about 20 miles distant.

Jan 1, 1932