Search Documents

By M. H. Stanczyk

The Bureau of Mines made bench-scale laboratory tests on a sample of typical Florida phosphate slime to determine alumina and phosphate extractions obtainable by agitation leaching, by baking and curing, and by a leach-electrolysis scheme. Recovery of mineral values from leached slime pulps by resin-in-pulp ion exchange contact and the reaction of the leached pulps to filtration, flocculation, and settling were also investigated. The best extractions of alumina and phosphate were obtained by (l) agitation leaching with sulfuric, hydrochloric, or nitric acid at an elevated temperature or (2) curing or baking the slime with sulfuric acid. Alumina extractions ranged from 80.8 to 90.0 percent and phosphate extractions ranged from 93.3 to 98.4 percent when the slime was leached at 90° C with sulfuric, hydrochloric, or nitric acids. Baking the slime with sulfuric acid at 200° C for 4 hours yielded an alumina extraction of 92.3 percent and a phosphate extraction of 97.0 percent, whereas curing with sulfuric acid at 100° C for 24 hours gave slightly higher alumina and phosphate extractions. Flocculation and settling properties of the slime were virtually unaffected in all cases. Filter area requirements, although somewhat improved as compared to untreated slime, remained relatively high. The lowest filter area requirement obtained was 44 square feet per ton of dry solids treated per day. Contacting leached slime pulps with ion exchange resins depleted the leach pulps of solubilized values; however, the filtration and settling properties of the barren pulps were unaffected. A leach-electrolysis scheme resulted in some concentration of solubilized phosphorus, but the method showed little promise of being commercially feasible.

Jan 1, 1966

By R. V. Ramani, J. Qin

"In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration. INTRODUCTIONA detailed experimental study on the characteristics of longwall dust cloud in operating longwall faces has been reported by Ramani, Qin, and Jankowski (1991). The study indicated that there are several important factors whose effects on dust transport in longwall faces need to be further investigated. In an operating longwall face, the effect of these parameters could not be easily isolated as control over the affecting parameters is not readily possible. In a simulated longwall face, however, these parameters can be controlled. Therefore, as a follow-up to the field study, a series of controlled experiments were conducted in a full scale simulated longwall face in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines [Qin, 1992]. Specific aspects which were addressed during the experimental design phase included determining the types of samples to be collected, selecting proper instruments to collect these samples, and developing detailed sampling and time-study plans to correlate the dust concentrations with face activities. Two types of dust--anthracite and bituminous--were used. Dust dispersion rate into the air as well as the source dust particle size distribution were documented. Control was exercised over both air velocity at the face and air leakage along the longwall face. During experiments, the dust source was moved to simulate the shearer movement at operating longwall faces. Detailed descriptions of the design of experiments, experimental results, and data analyses follow in the subsequent sections."

Dec 1, 1996

By Lloyd A. Morley, Alan M. Christman

General A review of the literature has revealed important areas which should be investigated during the field work. Of the utmost importance is the safety of mine personnel. Should a phase-to-ground fault occur on a shovel or other piece of equipment, current may return to the substation through the machine's contact surface with the mine floor, thereby raising the frame above ground potential and posing a shock hazard to anyone who touches the equipment. If the frame-to-earth resistance is very low, then no dangerous potentials will be developed, and a basis for elimination of the ground conductors from trailing cables could be postulated. However, should the contact resistance be high, then lethal voltages could be present on the machine frame. In this instance, low-resistance ground conductors in the trailing cable would be a necessity. Therefore, field tests should include measurements of the earth resistance of electrically operated portable or mobile mining equipment such as shovels, draglines, and drills. When the electrical distribution system is subject to lightning discharges, the grounding grid must safely carry to earth and dissipate enormous current surges. It is essential that the grounding grid have a low value of earth resistance, because any potential developed across the grounding grid as a result of current flow will appear on the frames of all machinery connected to the grid. Thus, an earth resistance

Jan 1, 1976

By N. S. Dalal, X. Shi

"The oxidation of NADPH by vanadate(V) in the presence of glutathione reductase showed typical enzymatic kinetics. The oxidation was inhibited by N-ethylmaleimide, a glutathione reductase inhibitor. Superoxide dismutase had no significant effect on the oxidation, indicating non-involvment of the superoxide radical. The vanadate(V) reduction was found to be a one-electron transfer process. These results suggest a new pathway for vanadate(V) metabolism and a new function of glutathione reductase. Compounds of vanadium(V), such as NaV03 , exert potent toxic effects on a wide variety of biological systems (1-3). Despite intense current activity, however, the biochemical mechanism of vanadate(V) toxicity is still not well understood (1- 14). It is believed that one of the important pathways involves the oxidation (by vanadate(V)) of NAD(P)H (15, 16), but, to our knowledge, there has been no report of the identification of any vanadate(V) reductase. With a view to finding if there exists any vanadate(V) reductase, we have investigated the oxidation of NADPH by vanadate(V) in the presence of glutathione reductase. Glutathione reductase (GSSG-R)2 was selected because our previous studies have shown (17) that GSSG-R can act as a reductase for chromate(VI), which is isoelectronic with vanadate(V). We find that GSSG-R does indeed function as a NADPH-dependent vanadate(V) reductase, thus pointing to a new pathway for the metabolism of vanadate(V), as well as to this property for GSSG-R. MATERIALS AND METHODSSodium metavanadate (NaV03 ), henceforth vanadate, was purchased from Aldrich and its solution was always freshly prepared. The GSSG·R used was from bovine intestinal mucosa and was purchased from Sigma. The oxidation of NADPH was followed photometrically as the decrease in absorbance at 340 nm. The spin trap, 5,5-dimethyl- pyrroline-N-oxide (DMPO), was purchased from Aldrich and used without further purification, since very weak or no spin adduct signal was obtained from the purchased sample when used alone.ESR spectra were obtained at X-band (9.7 GHz) using a Bruker ER200 ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR gaussmeter (Bruker, Model ER035A) and the microwave frequency was measured with a digital frequency counter (Hewlett-Packard, Model 5340A). An ASPECT 2000 computer was used for data storage and analysis. The concentrations given in the figure legends are the final concentrations. All experiments were carried out in the phosphate buffer solution (pH 7.2) and at room temperature."

Jan 1, 1990

By Lewis V. Wade

This report provides background information concerning a mine roof simulator currently being considered by the Bureau of Mines. The simulator is a mechanical device with the ability to simulate the forces and displacements associated with mine roof over an area 20 by 20 feet. The topics covered in the report include a conceptual description of the system, definition of system capabilities, discussion of how such capabilities were decided upon, description of available control modes, and a comparison between the mine roof simulator facility and similar facilities existing elsewhere.

Jan 1, 1974

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Nicaragua has been prepared from the best available information in Washington , but is released subject to correction and amplification , if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Jul 1, 1930

By Michael S. Miller

The Carson-Iceberg RARE II study area, consisting o; 209,990 acres (134,983 ha), is on the crest of the Sierra Nevada in California, about 35 mi (56 km) south of Lake Tahoe. The area is divided into four parts: C4-986; C5-986; and B5-986, north and south portions. No mineral production has been recorded for the area. However, gold, silver, and tungsten resources and potential for additional resources have been estimated for the area and just north of area C4-986.

Jan 1, 1981

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines" in various foreign countries. In the preparation of this interpretation of the laws of Norway, use has been made of William R. Orrmins' translations of various acts of the Norwegian Government, which were forwarded from the American consulate at Oslo^ and transmitted to the Bureau of Mines through the courtesy of the State Department. This digest is released subject to amplification and correction, if necessary, by the proper American foreignservice officers.

Nov 1, 1932

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By A. Z. Dimitroff

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By J. H. Wiggins

"The tests described below were conducted by the Bureau of Mines at a lease in Oklahoma on installations designed to decrease evaporation losses of crude oil Pram storage tanks. Use of the lease was granted by the Oklahoma Producing and Refining Corporation of America. Tankage was obtained through the courtesy of the Parkensburg Pig and Reel Co. The purpose of the installations and tests was to demonstrate the value of making crude-oil storage tanks gas-tight, rather than to determine the amount of evaporation in any one type of tank. None of the tanks used were absolutely gas-tight, but one of them was very nearly so. They comprised a tank of the ordinary open type with an 18-inch manhole, a tank with a ""4-inch vent"", a tank with a ""smaller vent"", and a tank which had only ""pin holes"" through which air and vapor could pass freely. On the last two tanks any excess pressure was taken care of by an automatic differential pressure regulator.The results obtained in these tests indicate that tight tankage will soon pay for itself. They will not, however, serve as a basis on which a producer can compute the actual number of days necessary for tight tankage to pay out, because the oil used was exceptionally volatile. It is probable that the average evaporation loss in the Mid-Continent field is at least one-half as great as that shown by these tests, and if this is true, the saving that would be effected by providing tight tankage on the lease will undoubtedly justify the expense. The installation of evaporation-proof tanks on the lease has been delayed by the failure of production managers to realize, first, that their evaporation losses are enormous, and, second, that they can practically eliminate these losses by a simple and inexpensive installation."

Apr 1, 1921

By G. B. Gait

This report is the fourth in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of 70 mines in the Western Middle field is presented. Previous reports were catalogs of microfilmed maps of mines in the Eastern Middle field and in the Wyoming and Lackawanna Basins of the Northern anthracite field. Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1971

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010

By Steven J. Page

Responding to the increasing concern for dust control in metal and nonmetal mining, the Bureau of Mines investigated typical dust reduction efficiencies of wet bar cutter machines as they are presently being used in salt mines. Wet bar techniques have previously been used in coal mines, achieving dust reduction efficiencies ranging from 11 to 60 pct. Two different wet bar techniques, namely, the front spray and the water trickle, have been studied as they are currently being used in two salt mines. Preliminary results show that the dust reduction efficiencies have a large variation (0 to 66 pct), as is the case for wet bars used in coal. However, whereas wet bars in coal required 3 to 4 gpm water consumption, wet bars in salt obtained similar efficiencies with only 0.1 to 0.4 gpm. The most reliable data obtained during this study show that the front spray system consistently performs at efficiencies between 41 and 66 pct, with an average of 54 pct. The results indicate that, although wet bar cutter techniques in salt mines are a relatively simple and inexpensive means of dust control with a minimum of water consumption, further investigation should be performed to fully evaluate and optimize wet bar cutter dust reduction efficiencies.

Jan 1, 1980

By E. J. Gleim

Many people consider the mining of coal to be an extremely hazardous occupation; but it should be remembered that most large industries have to meet special conditions which, if not dealt with properly, might become hazards to life and property. Mining men may not always be fully aware that some practices and certain equipment that is incorrectly designed or maintained can lead to dangerous conditions. In endeavoring to help the coal-mining industry to prevent accidents and disasters, the Bureau of Mines has engaged in a program of education on conditions and practices that must be avoided. An effective way to teach safety is by visual demonstration. For example, it is generally known that certain kinds of electrical flashes have ignited explosive atmospheres in mines, but actually to see and hear explosions caused by electrical sparks of different size and character under laboratory control is likely to teach a much more emphatic and lasting lesson than would be learned by merely reading about them. The interest manifested by those who witness the demonstrations seems to prove that this is true. The purpose of the demonstrations is not to discourage the use of electricity in mines, but rather to indicate what types of equipment (including some generally regarded as harmless) can ignite gas and what safeguards have been developed to prevent such ignitions. It is hoped that this information will improve the ability of mining men to cope with underground hazards.

Jan 1, 1937

By C. W. Smith

Research was conducted to evaluate the effectiveness of a well-point dewatering system in conjunction with a french drain to intercept waste impoundment leakage while reducing the volume of waste water requiring treatment. A well-point dewatering system composed of 585 production wells was installed around the perimeter of a leaking impoundment that previously used only a french-drain system for leakage control. The placement of the well-point system was designed to intercept and remove the leakage from the groundwater before the contaminant reached the french drain. Groundwater monitoring at this site revealed that after a period of approximately 40 days the well-point dewatering system had stabilized and effectively prevented the further spread of contamination to the french drain.

Jan 1, 2010

By Terry L. Muldoon

The Bureau of Mines conducted an investigation to quantify microphone response variations that could result when the microphone is worn by a worker, as with a personal noise dosimeter, and to suggest an optimum placement and orientation of the microphone for noise exposure measurements. Previous studies have shown no significant variations in a diffuse field. This investigation, therefore, was conducted in the free-field conditions of an anechoic chamber using an anthropometric dummy as a subject, and broad band noise as the acoustic stimulus. This investigation established that, in a free field, the wearer's body does significantly affect microphone response; the response variations are a function of azimuth, and location and orientation of the microphone. Results suggest that locating the microphone on top of the subject's shoulder, oriented parallel to the body axis, should yield data comparable to that obtained using a sound-level meter.

Jan 1, 1973

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some diamond drilling at the Almedia deposit In an endeavor to find an additional source of supply of lead and zinc. It is reported that in 1816, lead and zinc minerals were found in the limestone quarries near the boundary line between Scott and Center townships. In an attempt to develop these minerals in paying quantities, an alit was driven for several rods into a bluff Just west of the present Almedia mine, This is believed to be the Web mine, mentioned briefly by Parker Cleaveland in 1816. In 1901 the Almedia mine was developed by an open cut and three shafts. The hoisting shaft at the time of drilling by the Bureau of Mines was sounded to a depth of 115 feet. A concentrating plant reportedly made shipments to Hamburg, Germany, for reduction. The deposit is in a somewhat slaty limestone. The ore occurs in a northeast fracture zone along the strike of the limestone and dips to the southeast. Old miners state that the ore appeared as large chunks of galena and sphalerite. In 1949, to investigate the downward extension of the oreshoot, the Bureau of Mines drilled four holes aggregating 1,126.3 feet.

Jan 1, 1950

By Peter N. Gabby

In 1990, the Bureau of Mines conducted a mineral resource investigation of the 12.321 acre Black Warrior study area, one of several proposed additions to the Sawtooth Wilderness. No identified mineral resources were delineated. There were 123 lode and placer claims in or adjacent to the study area. There is a known hot spring adjacent to the study area, but presently no geothermal leases are pending. Lode mines in pr adjacent to the Black Warrior study area have produced 4,022 tons of ore from which 1,981 oz of gold and 811 oz of silver were recovered. None of the vines are currently active. During the field study 125 rock samples were taken. Significant gold assays and favorable geologic characteristics at seven properties indicate that gold occurrences and resources with byproduct metals may exist in the study area. Two other sites yielded anomalous gold assays; however, sage favorable geologic characteristics are lacking. Presently, identified gold resources are being delineated by drilling programs in the nearby Atlanta and Rocky Bar mining districts. These districts have geologic characteristics similar to the Black Warrior area. During the field study 22 placer samples were taken. In most places where an anomalous concentration of gold was found, the stream channels are too narrow for operations other than recreational suction dredges. However. One area is estimated to contain over 2 million yd3 of gold-bearing gravels.

Jan 1, 1992