Search Documents

By J. H. Bilbrey

A recording thermobalance ,vas used to determine the rates of oxidation of mol-ten tin over the temperature range 550°-900° C. Oxidation rates were found to vary widely for a given temperature, as previously reported by other investigators. 1 X-ray diffraction data indicated that the probable cause of these variations was the development of preferred orientations in the crystals forming the oxide film. No reasons for the differences in degree of preferred orientation were discovered. For relating the weight of the oxide formed (w) to the time of oxidation (t) an equation of the form wn = kt was found to best represent the experimental data. INTRODUCTION In the course of conducting investigations on the feasibility of using selective oxidation techniques for the purification of various metals in the molten state it was soon discovered that data on the oxidation of molten metals and alloys were very scarce. In contrast to the many hundreds of publications on the oxidation of metals in the solid state there are relatively few articles on the rates of molten-metal oxidation. In view of this scarcity of data, it was decided to institute a series of investigations into the oxidation processes of molten nonferrous metals and alloys with the expectation that the information derived could be put to practical use in developing and improving refining processes based on selective oxidation. This report is the first of a series in which oxidation data for molten nonferrous metals and alloys are presented.

Jan 1, 1955

By E. D. Eastman

"The factors that determine the efficiency of reduction of iron oxides by gaseous reducing agents may be considered in two classes; those which effect the equilibrium between the reacting substances end their products, and those which affect the rete of reaction. Both sets are of prectical importance, the former as influencing the maximum possible efficiency and the latter as determining what fraction of the maximum yield may be readily or profitably obtained. In addition, the thermal changes attending the reduction greatly affect the chance of successful industrial application of any such process, and knowledge of them is necessary for the intelligent design of apparatus and control of the reaction. Some aspects of each of these three divisions of the problem are discussed below.I. The Maximum Reducing Power of Fuel Gases on the Oxides of IronsThe gases that heve been considered specifically in this work are coal gas, water gas and producer gas, typical analyses” of which are given in Table 1 Of the various hydrocarbons represented in Table 1, (several being grouped or averaged as C2R4), methane is the only gas assumed to be capable of existence at appreciable pressures under the conditions of interest here. The equilibria in the several systems which may ensue when one of the above gases is allowed to react with the iron oxides, may therefore be represented in the most general case by equations of the type of the following arbitrarily chosen ones:"

Jun 1, 1923

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

By William M. Nabors

As a part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers are studying secondary oil-recovery projects in the United States. Published reports that set forth the pertinent facts of these operations help others to profit by the experience gained. This report presents the results of a study of secondary-recovery methods used in Kentucky by the Cumberland Petroleum Co. on its L. C. Bailey lease, Oil Springs pool, Magoffin County, Ky. This is believed to be the first water-flooding project in eastern Kentucky (fig. 1).

Jan 1, 1958

By D. A. Lucero, J. E. Brockmann, L. A. Mondy, K. L. Rubow, D. J. Rader

"Department of Mechanical Engineering, University of Minnesota, Minneapolis, MNExperimental and correlated stage responses (the fraction of particles entering an impactor that are collected on a stage) are presented for the Andersen Mark III and Marple personal cascade impactors. The impactors were operated upright and fully assembled so that interstage interference and wall losses could be properly studied. The observed stage responses showed maxima that fell significantly short of unity, meaning that a monodisperse aerosol is never collected exclusuvely on one stage, but is distributed among several stages and internal losses. Correlations for the stage responses are presented so that the experimental results can be used to determine size distributions with available data-inversion algorithms. Simulations with log-normal distributions show significant differences between dpa50 histograms and the more accurate distributions that result by taking the response functions into account.Cascade impactors are widely used for the measurement of aerosol size distributions; their ruggedness and simplicity of operation make them an attractive choice for a variety of environments. In one common application, the aerosol of interest is drawn through the impactor, and the amount deposited on each stage is determined gravimetrically. The primary objective is to extract as much information as possible about the initial size distribution from the resulting set of weights. Unfortunately, the reconstruction of contin-uous size distributions from finite data sets is an ill-posed problem. Not surprisingly, a variety of such reconstruction techniques are presently in use; the success of each method depends on the particular nature of the aerosol sample and the instrument response.Inversion of impactor data by any of these techniques requires that the response functions for each stage be known. The stage response function gives the fraction of particles entering the impactor that deposits on that stage. Values of the response function range from zero to one, and depend on impactor operating conditions (e.g., geometry, flow rate, and gas properties) and particle properties (e.g., diameter, density, and shape factor). As interstage interferences and particle losses will affect each stage's response, experimental determination of stage responses should be made for fully assembled impactors. Unfortunately, impactor stage response functions are rarely reported; rather, single-stage efficiency curves are given that provide an incomplete description of impactor performance.This paper presents experimental stage responses for two fully assembled cascade impactors: the Andersen Mark III and Marple personal impactors (model 298, Andersen Samplers, Inc., Atlanta, Ga.). These calibrations were performed with monodisperse liquid droplets for both impactors and also with monodisperse solid spheres for the Marple personal impactor. The calibration results for the Mark 111 impactor presented here have been previously reported in the response-function format (Rader et al., 1989). The calibration results for the Marple personal impactor, however, were originally presented in the single-stage efficiency for¬mat (Rubow et al., 1987) and have been reanalyzed in this work. Losses within both impactors are considered, and their treat¬ment within data inversion techniques is dis¬cussed. In addition, correlations for each impactor's response functions are presented so that these calibration results can be easily included in data-inversion algorithms. Size distribution inversions using these response correlations are compared with the standard cut-point method for two lognormal test dis¬tributions."

Mar 1, 1992

By Martin J. Gavin

In an earlier paper (Karrick, Lewis, C. A convenient and reliable retort for assaying oil-shales for oil yield: Bureau of Mines, Reports of Investigations, Loral No. 2229, March, 1921. Reprinted in Eng. and Min. Jour, April 30, 1921, also in Mining & Met., May, 1921) which describes the apparatus and method used in the laboratories of the Bureau of times for assaying oil-shales, no mention is made of the quality of oil obtained when the apparatus is operated under conditions determined to be most suitable for producing highest yields of oils. So many inquiries regarding the nature of the oil have been received, that it seems advisable to present a short report on the subject. Experimental work indicates that it is possible to vary the quantity and quality of the oil obtainable with the assay retort from a given shale by varying the conditions of retorting. As an example, some figures that are averages for several closely agreeing tests are shown below.

Jan 1, 1921

By A. L. Pierce

This paper describing the mining practice at the Spring Hill mine of the Montana Mines Corporation, Helena, Mont., is one of a series issued by the Bureau of Mines on mining methods and costs in various districts. Its purpose is to summarize improved methods whereby lower costs have recently been obtained. These improvements are principally the adoption of a modified sublevel stoping method of mining the use of grizzlies underground improvements in haulage, and rage bonuses. The Sprint Hill, Trine is situated in Grizzly Gulch, 3 miles southwest of the city of Helena. Helena is on the links of the Northern Pacific and the Great Northern Railways; and the East Helena smelter of the American Smelting and Refining Co. to which the concentrates from the mine are shipped, is but 6 miles east of Helena. The mine is probing 150 to 200 tons of gold ore per day, with an underground crew of about 40 men.

Jan 1, 1931

By J. E. Miller

This paper reports experimental determinations by the Bureau of Mines of compressibility factors to 4,000 pounds per square inch absolute (p.s.i.a.) for helium at temperatures from -10° to 130° F. and for 16 helium-nitrogen mixtures at 70° F. This information is needed for computing accurate discharge volumes and is necessary for determining an average-density value for use in orifice-meter formulas. In thermodynamic calculations, several functions of the compressibility factor with pressure and temperature are required. The data in the original publications (6, 8)5 of this study have been reexamined and have been given a more comprehensive treatment. The recalculated compressibility factors are higher by approximately 0.2 percent because in the earlier work a linear relationship between the compressibility factor of helium and pressure was assumed.

Jan 1, 1961

By Harold B. Ewoldt

The Appalachian Ores Co., Sweetsprings, W. Va. was a small but persistent producer of manganese ore for several years prior to 1942. Most of the ore mined was hard, nodular psilomelane, with some pyrolusite and, wad, occurring in clay. The Bureau of Mines started an investigation of the area in January 1942 and completed the work in May 1942. Twenty-four churn-drill holes were bored, aggregating 2,084 feet. A total of 420 feet of test pits was sunk on selected drill holes to check the churn-drill sampling. Twelve drifts and crosscuts aggregating 139 feet were driven from the bottom of test pits to investigate concentrations of manganese nodules. Three hundred sixty-six churn-drill samples and 102 other samples were sent to Bureau laboratories for analyses. Beneficiation tests were conducted in the Burp.au of Mines laboratory in Rolla, Mo. Results of testing 10 samples indicated that approximately 80 percent of the material in crude ore could be discarded by log washing. Gravity tests indicated 'that 55 percent of the total manganese in the crude ore was recoverable as a gravity concentrate averaging 34.6 percent manganese.

Jan 1, 1949

By H. A. Watson

The introduction and use of synthetic materials in various applications may lead to potential hazards from toxic, gaseous, decomposition products if these materials are subjected to conditions abnormal to their intended use, such as high temperatures or burning from accidental causes. This report covers an investigation of such possible hazards from toxic gases produced by the burning or thermal decomposition of some low-density, expanded, synthetic materials, three of which consisted of polyvinylchloride and one of acrylonitrile. In the production of certain expanded plastic materials, Chemical blowing agents frequently are used to produce a cellular structure. One of these blowing or foaming agents contains azo-bis-isobutyronitrile, which is designated in this report as PN. Information indicates that a product of decomposition of this blowing agent, formed in the blowing operation, is tetra-methyl-succino-nitrile, designated as TSN, Which is significantly toxic. Decomposition of the blowing agent, with release of its azo nitrogen, is represented by the following reaction:

Jan 1, 1951

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963

By Ronald A. Munson

Samples of the naturally occurring zeolites phillipsite, clinoptilolite, erionite, and chabazite have been surveyed for their gas adsorption, ion exchange, and other characteristics. Chabazite and erionite, which are generally more stable, also have higher methane adsorption capacities than do the other natural zeolites. Both natural erionite and natural chabazite are classified as small-port zeolites on the basis of their inability to adsorb chlorotrifluoromethane. In the range of 8 to 100 mesh, the adsorptive capac-ity of natural zeolites is improved only slightly by a decrease in particle size. The capacity of natural clinoptilolite to adsorb methane is increased by cation replacement by the hydrogen ion and decreased by exchange with calcium ion. Natural phillipsite, which is easily decomposed by heat, adsorbed methane to a limited extent.

Jan 1, 1973

By E. C. Perkins

Preliminary experiments are reported utilizing bacteria to leach manganese from a variety of domestic low grade manganiferous materials. In two large leaches manganese extraction ranged from 71.7 to 92.5 percent, and the products analyzed over 48 percent manganese. Nutrient requirements and leaching time experiments were made. The mechanism of leaching is not understood, but is different than the mechanism encountered in the microorganism accelerated leaching of copper in the presence of sulfide minerals.

Jan 1, 1962

By Thomas M. Barczak

Longwall roof behavior is characterized by strata displacements in both the face-to-waste (horizontal) and roof-to-f1oor (vertical) direc-tions. The roof support structure provides resistance to this motion by translation of these displacements into vertical and horizontal support loading. Observations indicate that the shield reacts with both a vertical and horizontal force to uniaxial convergence (displacement). However, there are different magnitudes depending on whether the displacement is vertical or horizontal. This makes it possible to use supports as monitors of strata activity and loading. The Bureau of Mines examined this behavior using a linear elastic model of the support structure with two degrees of freedom. Vertical and horizontal load reactions were related to associated displacement actions of the strata. This was done by determining the stiffness of the shield under controlled vertical and horizontal displacement motions in the Bureau's mine roof simulator. This report provides example predictions of strata convergence and isolation of horizontal support loading due to vertical roof convergence using the linear elastic shield model. The report also examines efforts to determine strata behavior by direct measurement of support displacement.

Jan 1, 1987

To suppress the natural bacterial action in acid mine drainage (AMD), the major contributor to acid formation. Approach Recycle partially-treated affluent back to the source of AMD within a mine, or to the coal or coal-waste stockpile. This effectively eliminates any further biologically-promoted AMD by inhibiting catalyzed weathering or oxidation by acid-forming bacteria. How it Works AMO-type effluents can be largely reduced by "recycling" the acidic outflow back to the source of AMD within a mine or to the Input side of a waste pile to percolate through the reactive pyrite and bacteria mixture. The bacteria in the cell thrive on the oxidation of ferrous to ferric iron through the electron transfer, Fe2 +[=]Fe3 + + e. Its reaction product [s, therefore, essentially ferric iron. While small quantities of Fe3 + will not interfere with the exponential multiplication of the bacteria

Jan 1, 1982

By D. B. Dow

"Natural gas-gasoline is made by collecting in the liquid state the condensable hydrocarbon vapors that exist in different natural gases in varying amounts. In the richer type of natural gas the gasoline is generally recovered by compression and cooling. If exceedingly high pressure or low temperature is used, there is dissolved in the gasoline a large amount of very volatile material, which evaporates rapidly at atmospheric temperature and pressure.In the leaner type of natural gas, the gasoline vapors are selectively absorbed from the permanent gases by passing the natural gas through an absorbing oil. The gasoline is recovered by distilling the saturated oil, and as compared with ""compression"" gasoline is of high Baume' gravity and low vapor pressure. Before a volatile gasoline can be transported in tank cars, it is necessary to decrease its volatility in order to lessen the risk of fire or explosion, as well as to prevent excessive evaporation in transit. This can be accomplished either by weathering the gasoline, or by blending it with a more stable material, naphtha being commonly used in the weathering process the more volatile portions of the gasoline are allowed to evaporate and the losses in volume are very large, therefore, blending is preferable, wherever possible.It is very difficult, however, to produce by blending, in gasoline plants, a motor fuel which is equal to straight-run refinery gasoline. In order to make a blended motor fuel of a grade equal to straight-run gasoline, only a small percentage of natural gas-gasoline can be blended with the naphtha, consequently it is customary to blend the gasoline with only enough naphtha to enable It to be shipped to an oil refinery when the material is again blended to form a finished motor fuel."

Sep 1, 1921

By Alexander May

In its role to provide technology to prevent or limit adverse environmental impacts associated with mining or minerals processing, the Bureau of Mines has conducted research at its Tuscaloosa Research Center to asess the environmental impacts of phosphogypsum produced by the Florida phosphate industry. Over the years, stockpiles containing 335 million tons of phosphogypsun have accumulated and the industry continues to generate an additional 33 million tons a year. Samples from approximately 1,000 feet of drill core, obtained from nine stockpiles were characterized using chemical, X-ray diffraction, emission spectrographic, radiological, and physical means. The data developed indicated that phosphogypsum is not a corrosive or toxic hazardous waste as defined by Environmental Protection Agency criteria. Radium concentration averaged 21 picocuries per gram and its content was inversely related to particle sizes. Thirty-nine elements were detected in phosphogypsum; concentrations of these elements did not vary with depth within the stockpiles.

Jan 1, 1982

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Selective cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. Leaching the scrap for 90 min at 110° C in 2.2NH2S04 under 400 psig 02 yielded 97% Cd extraction; however, cadmium content of the residue ranged between 4% and 7%. Soluble iron was added to the lixiviant to catalyze oxidation of the CdS component. Tellurium and sulfur remained in the leach residue primarily in the elemental form. The iron and tellurium were removed from the cadmium-rich leach liquor by adjusting the pH to 5.3. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Alternative leaching and purification schemes are discussed.

Jan 1, 2010

By D. G. Collins

As part of its effort to develop ways to maximize resource recovery, the Bureau of Mines investigated the extraction of vanadium from Western phosphate beneficiation tailings with H2S04 and/or H3P04. Dissolution of the vanadium was accomplished by digesting a mixture of acid and a 50-pet-solids, tailings-water slurry. In the most effective method investigated, vanadium and phosphorus were leached by digesting the slurry at a constant boiling temperature (1000-1100 C) in a stirred reactor. In batch tests, maximum vanadium dissolution was 95 pet. In continuous-circuit tests designed to further evaluate vanadium dissolution at con-stant boiling temperature in a continuously stirred reactor, vanadium dissolution ranged from 70 to 85 pet. An economic evaluation of the process demonstrated that H2S04 consumption is the major cost factor. Based on the value of the vanadium product with no allowance for a phos-phate product, the cost of producing the V205 is more than twice its value. The potential for profit would depend upon the value of the phosphate fertilizer produced from the impure H3P04 remaining after vanadium extraction.

Jan 1, 1985

By L. A. Neumeier

The Bureau of Mines evaluated the properties of a Zn-0.75 pct Cu-0.12 pct Ti alloy extruded at temperatures between 400° and 720° F. The extrusions were made with a reduction ratio of 28-to-l and at relatively slow speed. Rod was also extruded at 560° and 640° F with a reduction of 255-to-l. With increased extrusion, temperature, extrusion pressures decreased substantially and creep resistance of the rod improved significantly. Coefficients of thermal expansion were low in the long rod dimension. Microstructures, hardness, and tensile properties were also evaluated, and a limited evaluation was made of bend ductility at 32° F for the rod extruded with the 255-to-1 reduction.

Jan 1, 1969