Search Documents

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By L. B. Pankratz

Present-day interest in the rare-earth elements and their compounds, for both metallurgical and ceramic uses, makes it highly desirable to accumulate basic thermodynamic data that can be applied to theoretical considerations of the processing of these substances. Such data still are seriously lacking. This Bureau of Mines paper reports the results of high-temperature heat content measurements of the sesquioxides of four rare-earth elements--europium, gadolinium, neodymium, and samarium--and of the closely related element, yttrium. The temperature ranges covered by the measurements are as follows: Monoclinic Eu2O3, 298°-1,802° K. Cubic Eu203, 298°-1,350° K. Monoclinic Gd203, 298-1,802° K. Cubic Gd203, 298°-1,550° K. Hexagonal Nd203, 298°-1,795° K. Monoclinic Sm203 298°-1,798° K. Cubic Sm203, 298°-1,149° K. Cubic Y203, 298°-1,799° K.

Jan 1, 1962

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

By Agnes Y. Lee

The Bureau of Mines has developed an effective hydrometallurgical method to recover high-purity Pb metal and elemental S from concentrates. This low-temperature process eliminates S gases and Pb emissions, in contrast to the current high-temperature smelting technology. The method consists of (1) oxidative leaching with H202, Pb02, and waste fluosilicic acid at 95° C to produce a solution of PbSiF6 and a residue containing elemental S, (2) electrowinning the PbSiF6 solution at 35° C to produce 99.99 pct Pb metal and H2SiF6, and (3) solvent extraction to recover S, leaving a residue containing Cu, Ag, and other metal values. Spent electrolyte was recycled repeatedly, with impurity buildup controlled by controlling the leach parameters.

Jan 1, 1986

By E. L. Garton

The Bureau of Mines for a number of years bas been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from many oil fields of Oklahoma are given in Bulletin 2915. Analyses of 21 representative crude oils from various producing zones of the Oklahoma City field are given in this report. A close study of the analyses reveals very few differences in the general characteristics and chemical properties of these oils.

Jan 1, 1932

By Alexander May

The U.S. Bureau of Mines conducted studies to determine if phosphate slag stockpiles at Tennessee Valley Authority's National Fertilizer Development Center were hazardous materials. The stockpiles were not hazardous materials as determined by Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test. Radium-226 concentration was 28.7 pCi/g in slag and 2.1 pCi/g in background material. Radium-226 was not leached from the slag. Fluoride concentration was 3.87 pct in slag, 0.18 pct in subsurface material under slag, and 0.08 pct in the background. Slag material permeability was 1.65 x 10-3 cm/s, and subsurface material permeability was 3.24 x 10-6 cm/s. Rain water, trapped in a depression on top of the east slag stockpile, became seepage water at the base of the stockpile. Concentrations of EPA toxic elements in seepage water were much less than concentrations from an EPA EP toxicity test on the slag. Twelve elements-Na, Mg, Ca, Sr, Ba, Cr, Mn, Co, Cu, Cd, AI, and P-had higher concentrations in seepage water than in rain water on top of the slag stockpiles, or in creek water adjacent to stockpile bases, indicating that they were leached from slag stockpiles.

Jan 1, 1990

By S. J. Gasior

Pilot plant studies showed the technical feasibility of fluidized-bed operation for producing hydrogen and synthesis gas by the steam-iron process. A mixture of iron and iron oxide from 20-to 100-mesh was partially reduced with a simulated producer gas and then oxidized with steam and/or carbon dioxide. Results of tests show the effects of pressure, temperature, bed height, gas-to-solids ratio, type of iron oxide, and composition of gas on the gas and solids conversions during reduction and oxidation. A baffled free-fall solids system was also found operable. The short residence time of about 5 seconds limited conversion of the solids.

Jan 1, 1961

By J. A. Herdlick

At the request of the War Production Board a preliminary examination of the Big Ben molybdenum prospect near Neihart, Cascade County, Mont., was made by the Bureau of Mines under G. N. Bennett, mining engineer, Bureau of Mines Montana district office, in September 1942. Formal investigation, consisting of sampling, core drilling, and metallurgical testing, was later undertaken and completed in 1943. Field work was directed by Robert D. O'Brien, mining engineer, Montana district office, under the supervision of E. W. Newman, supervising engineer, Montana district office. This report describes the deposit, presents the factual data obtained from the sampling and core-drilling operations, and summarizes the results of the metallurgical studies. The deposit was first located and prospected in 1922 by the present owner, Frank Mansikka of Neihart, Mont. Periodic examinations made by responsible mining interests were culminated in 1938 when the Federal Mining & Smelting Co. optioned and investigated the property. No ores have been produced from the deposit to date.

Jan 1, 1949

By P. D. Kovscek

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted mechanical cutting system to determine the effect of the high-pressure sprays on machine performance, airborne dust levels generated, and size of particles formed. Testing was conducted on a simu-lated coal block (coalcrete) while cutting at a water pressure of 190 psi and at water-jet-assisted pressures ranging from 1,000 to 6,000 psi. The shearer motor energy used by the shearer while cutting coalcrete was determined for each cutting condition. Results indicate that the motor energy required by the shearer for each ton of material cut did not vary significantly as the water pressure was increased. Results of dust measurements recorded near the cutting drum indicate that at water pressures above 3,000 psi, dust reductions up to 85 pct were achieved com-pared with cutting with conventional sprays. Analysis of the particle size distribution during cutting showed that increasing the water pres-sure resulted in increased median particle size. In light of these results, various mechanisms for water-jet-assisted cutting are discussed.

Jan 1, 1986

By K. K. Kershner, J. G. Donaldson

This investigation was conducted to obtain data on optimum conditions for chloridizing metal sulfides . Salt- roasting galena at 450° C for 8 hours chloridized 75 percent of the lead ; in an equal time of treatment at 750° C , the process chloridized 42 percent of the zinc in sphalerite . Hydrogen chloride at 500° C completely chloridized galena in 15 minutes , and at 600° C converted all of the zinc in sphalerite to the chloride in 4 hours .

Jan 1, 1963

By V. J. Lynch, A. L. Peyton

"INTRODUCTION AND SUMMARYThe Brewer mine, near Jefferson, Chesterfield County, S.C., was originally operated as a gold mines as late as 1890 this mine was reported to have been one of the large gold producers in the southeast,Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered by Pardee and Parks. 3/ of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.During the 1940's the Chemical Engineering Branch of the Tennessee Valley Authority and the Electrotecbnical Laboratory of the Bureau of Mines at Norris, Tenn., investigated topaz from the Brewer mine to determine the possibilities of its use as mullite and for the production of calcium fluoride.From July 1950 through. April 1951 the Bureau of Mines conducted a diamond-drilling project at the Brewer mine to determine the grade and extent of the topaz deposits. Ten diamond-drill holes, totaling 2,344 feet, were completed, and 231 analyses of core samples were made during the course of the project.This report presents factual data relating only to the diamond-drilling project, The placer deposits on the Brewer property were previously investigated by the Federal Geological Survey 4/."

Aug 1, 1953

By J. P. Powell

Systematic waterflooding was first tried in Washington County, Okla., in 1937, when a 40-acre project was begun in secs. 24, 29, 32, and 33, T. 27 N., R. 13 E., jointly by the Keener Oil Co. and the Phillips Petroleum Co. The property later was sold to Lee Morrison. A second project was begun in 1941 in sec. 14, T. 6 N., R. 12 E., by the Oklahoma Oil Corp. Both projects were abandoned by the end of 1942. A third project was begun in 1945 and the fourth in 1948, but 1949 actually was the beginning of intensive waterflooding development in Washington County. The results of previous waterflooding projects are described in Bureau of Mines Reports of Investigations.2 3 4/ Oil production in the county followed a similar trend, dropping to a low of 990,000 barrels in 1945, then steadily increasing until 1956, when more than 4 mil-lion barrels of oil was produced. Most of the increase in oil production is directly attributable to water injection.

Jan 1, 1957

By Gregory J. Chekan

The Bureau of Mines, in an effort to improve planning and development in coal mining, is investigating strata interactions associated with mining of multiple coalbeds. Two common interactions that occur between adjacent coalbeds are subsidence and pillar load transfer. The study described involves underground observations and measurements conducted at two Pennsylvania mines, each affected by one of these interactions. At the mine affected by subsidence, measurements show that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. At the mine affected by pillar load transfer, Initial in situ measurements have shown the existence of a pressure arch in the lower workings. Prior research has shown that arch interaction between two adjacent openings can create stress concentrations in the in-nerburden. Underground measurements and results obtained from both mine sites correlate with theoretical and photoelastic multiple-seam models, and eventually these field data will serve to refine model accuracy. Further study of multiple-seam interaction mechanisms will lead to improved mine planning, increased resource conservation, and a safer working environment.

Jan 1, 1986

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness_ It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 33 to 40.0 pct. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3+3 sequence) ranged from 13.3 to 63.3 pct.

Jan 1, 1991

By M. H. Kline, Wing G. Agnew

"INTRODUCTION The Yancey-Crawford tract, located 1-1/2 nines east of Yancey station on the Norfolk & Western Railway in Rockingham County, Va. was from 1917 to 1941 considered an unusually promising manganese prospect. Because of the favorable geologic formations and because of the common occurrence of manganese in the district and Virginia's large production of these minerals from this area, geological report 3/ have listed this tract as the No. 1 prospect in the State. During World War I, extensive geologic studies were made to locate manganese deposits similar to those exploited at the Crimera mine near Waynesboro to alleviate this mineral shortage during the existing emergency.In September 1941 the Bureau of Mines started exploratory drilling on the tract in an effort to discover and block out reserves of manganese minerals as authorized by the 76th Congress under the Strategic Materials Act. After five drill holes wore sunk, the project was terminated October 1941."

Apr 1, 1948

By W. D. Mcmillan

The Dempsey tract in Washington County, Mo., had a small production of lead-zinc ore from shallow workings. Old dumps from early-day lead mining contain about 25,000 tons of ore averaging about 3 percent combined zinc and lead. Because of the urgent war requirements for lead and zinc, the Dempsey property was examined by Otto Ruhl, formerly an engineer of the Bureau of Mines in August 1942 and selected for further investigation by churn drilling twenty holes totaling 1,309 feet were bored in the fall of 1943. The results of the work are presented in this paper.

Jan 1, 1948

By R. H. Sprute

Underground accumulations of slimes in the Henderson mine are routed to two large collection pits where they are dewatered and consolidated by application of direct current. Densified material is then removed to ore cars by rubber-tired front-end loaders and transported out of the mine. This Bureau of Mines report describes the electrical dewatering installation and compares its efficiency of operation with that predicted from preliminary laboratory studies performed by the Bureau. Direct current from a 150-kw rectifier (applied for 44 hours at 400 amperes and 65 to 70 volts) converted slimes containing 25.3 percent solids to material ranging from 44 to 65 percent solids. Better results can be expected if the ramp and front sections of the pits are treated separately, using higher current density.

Jan 1, 1980

By Douglas F. Scott

This case study provides an example of how social marketing was applied to meet the needs of business customers. Federal regulations require that all companies develop a written program to track hazardous chemicals at their sites. The HazCom Writer, created by the National Institute for Occupational Safety and Health (NIOSH), is a software tool designed to help companies prepare their required Hazard Communications (HazCom) written plan and list all hazardous chemicals at the company's worksite. The social marketing goal was to provide a product for small- to medium-sized companies to use for federal HazCom rule compliance. The HazCom Wm'ter is a direct NIOSH response to customer and stakeholder needs (including the Mine Safety and Health Administration, the mining community, and Occupational Safety and Health Administration- regulated companies).

Jan 1, 2009

By G. L. Oldright, Virgil Miller

"This paper is the ninth 4 of a series on smelting in the lead blast furnace, and the fourth on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSThe authors wish to express their appreciation to Stanley A. Easton, Frank M. Smith, and A. F. Beasley, and to their staff for the whole—hearted cooperation that made it possible to obtain the data in this publication at the Bunker Hill smelter, Kellogg, Idaho.INTRODUCTIONIn tie account written of the conditions obtaining at the tuyere zone in the blast furnaces at Tooele (R. I. 2965) the authors gave references to articles covering (1) the effect of temperature on the equilibrium 2C0 - CO2 + C, (2) experimental work that has been done on learning the gases existing at various elevations in columns of burning coke, (3) extension of this work to the tuyere zone of an iron blast furnace, and (4) the paper itself gave similar analyses of the gaseous oxides of carbon at the tuyere zone of a lead blast furnace and showed the temperatures obtaining there. There were also references in the above paper to the literature on (5) how the lead compounds likely to be present might be ex¬pected to react. A careful study of the original articles selected as references will give a good background for the present work.The following very brief recapitulation may be convenient before considering the tuyere zone in the blast furnaces at Kellogg. The ""producer gas reaction"" (1) of course goes to the left at increasingly higher rates of speed with increase of temperature. When air is blown upward through a grate and a column of hot fine coke alone, oxygen as such penetrates from some 2 to 3 inches only, under the conditions obtaining as to the amount of surface exposed per unit volume of air. When air is blown at about 20 pounds pressure through the tuyeres in the side of an iron blast furnace into a column of coarse coke (plus furnace charge) it may penetrate for 30 inches before the oxygen is entirely used, burning first largely to CO2. Within wide limits, the rate of feeding air into the furnace has practically little effect on the composition of the gases obtaining in the fuel bed of fine coke, this being true particularly of the gases leaving the bed. Some 10.5 inches above the grate the gases contained 22 per cent of CO by volume, and a little further up the CO2 had practically disappeared. This gave the familiar three zones in both the iron blast furnace and the gas producer; in order of entry of the air, in the first the oxygen burned largely to CO2, in the second the CO2 was reduced to CO, and the third the CO2 was practically absent. In the furnaces at Tooele, conditions were somewhat erratic but the first two zones were present, there being, however, no zone in which CO2 and 02 were both entirely absent."

Apr 1, 1931

By M. P. Dalton

This paper which describes the milling practice at the Morning concentrator of the Federal Mining and Smelting Co., Mullan, Idaho, is one of a series being prepared by the Bureau of Mines. ACKNOWLEDGMENT The author wishes to acknowledge the assistance given by H. G. Washburn, general manager of the Federal Mining and Smelting Co., and by C. S. Price, assistant mill superintendent, in the preparation of this paper.

Jan 1, 1932