Search Documents

By Janet Torma-Krajewski, Pauline Lewis, Paul Gust, Lisa Steiner, Kean Johnson

Ergonomics processes described in the literature have been associated mostly with manufacturing, financial, electronics, and office settings where working conditions tend to be rather constant and repetitive. The information presented in this document demonstrates, however, that an ergonomics process can also be implemented in a setting such as mining where working conditions frequently change and workers are periodically exposed to extreme weather conditions. This document describes how Bridger Coal Company implemented an ergonomics process at its Jim Bridger Mine from 2001 through 2004. The process developed by the Ergonomics Committee, the promotion of the process to management and employees, and the impacts of the process on working conditions at the mine are reviewed. Barriers overcome and lessons learned are also described. Quotes from Bridger Coal Company employees are included in the document to add a personal perspective. Other industries with working conditions similar to mining, such as construction and agriculture, may find this information useful.

Jan 9, 2006

By R. L. Cosgriff

A commercial, battery-powered mine vehicle has been equipped for remote operation in coal mines. This vehicle is controlled by an operator from the remote station. Command signals originating at the remote station as well as video and data signals originating on board the vehicle are relayed between the remote station and vehicle using a single coaxial line. This coaxial line is normally 2,000 feet in length and is reeled in and out from a drum mounted aboard the vehicle The vehicle has a maximum speed of 6 ft/sec and a minimum speed of 4 ft/sec using 36-volt excitation of the traction motor. If this traction motor is excited by two of the three batteries, 24-volt excitation, the vehicle will travel at approximately 2 ft/sec. The speed can be reduced by the operator to 1 ft/sec. This vehicular system has been tested in coal mines. Presently, the major limitation of this system is associated with fatigue failure of the splices in the coaxial line and lack of mobility caused by its 3-wheel design.

Jan 1, 1974

May 1, 1997

To improve the level of hearing protection by providing workers with an inexpensive, easy-to-use device to check earplug fit. Background Approximately 30 million workers are exposed to hazardous noise on the job, placing them at risk of permanent hearing loss, tinnitus, and other disorders. Although the preferred solution is to eliminate noise through engineering controls or to reduce noise exposure through administrative controls, hearing protectors are critical when noise is unavoidable. Studies of hearing protector users have shown that average protection values in the real world are much lower than the labeled noise reduction ratings determined in laboratories with trained and motivated subjects. Even worse, many hearing pro­tector users get virtually no protection at all because of poor fit. The studies also show that users have a harder time achieving adequate protection levels with earplugs than with earmuffs. It?s difficult for users to tell if earplugs are working well just by looking at them. A more accurate approach is to check how much they block or ?attenuate? noise. Earplugs vary in their attenuation characteristics, with most providing a maximum of 20?35 decibels of noise reduction when worn correctly. Any earplug that?s suitable for use in noisy settings will attenuate noise by at least 15 decibels. Personal fit testing is an effective way to help hearing protector users improve the fit and protection levels of the devices. However, existing fit-testing systems are expensive and unsuitable for use at many industrial worksites.

Dec 1, 2008

By John D. Foulkes, David A. Curtis, Robert L. Lagace, John L. Rothery

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal mines. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to deter- mine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m5 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to be attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By John A. Burgess

The Carson Hill mine of the Carson Hill Gold Mining Corporation is at Melones, Calaveras County, Calif. It is one of the numerous mines on the Mother Lode of California. The property extends for 8,400 feet along the outcrop of that important vein system. The elevation at the haulage level is about 1,000 feet above sea level. ACKNOWLEDGMENTS Acknowledgment of assistance in the preparation of this paper is made to Frank Wagner, underground superintendent; Max Petersen, engineer; and Homer Mann, assistant engineer. The geology of the Mother Lode has been described by Adolph Knopf in Professional Paper 157 of the United States Geological Survey; references to general geology have been abstracted largely from Knopf.

Jan 1, 1937

By Brian T. Brady

The year 1992 recorded unimpressive economic growth and uncertainties over what changes would occur for the financial market. Falling interest rates in the United States and elsewhere tended to exert a number of positive influences on financial markets and, indirectly, the mining and quarrying industry. The interest rate declines during 1992 were no exception. Lower rates prompted many investors to turn their attention to long-term investments such as stocks that offer potentially greater rates of return, causing large cash inflows into the equity market. Lower rates made it easier for businesses to finance growth and for consumers to finance the purchase of products businesses made. Also the rates enabled many companies to increase their health and profitability by refinancing their existing loans at lower rates. Falling interest rates were not confined to the United States. With Japan and Western Europe in the midst of economic slumps, marketing authorities in many countries overseas lowered rates in an effort to stimulate business activity. True to form, that contributed to stock market rallies abroad. Stabilizing inflation and lower interests stimulated the industry during 1992 and will likely influence favorably the industry for the next few years.

Jan 1, 1992

By V. A. Marple, K. L. Rubow, B. A. Olson

"INTRODUCTION Inertial classification, gravitational sedimentation centrifugation, and thermal precipitation arc techniques that can be used to collect particles for subsequent analysis or for particle classification. The inertial classifiers, which include impactors, virtual impactors, and cyclones, are widely used in the sampling or particles. Settling chambers, which include centrifuges as well as gravitational settling devices, are less widely used. Thermal precipitators arc seldom used.Impactors, in particular, have been used extensively, studied both theoretically and experimentally, and arc the instrument or choice for the determination or aerosol mass size distributions. Many versions or impactors arc available commercially and many more have been designed, built, and used in special studies.Virtual impactors are a more recently developed inertial classifier and possess a feature not round in conventional inertial impactors; namely, that the particles remain airborne after classification compared to the conventional impactor, where the particles arc collected on a solid surface. The feature or keeping particles airborne is important for transporting the particles to other particle-analyzing instruments, or to filters, and in concentrating particles larger than the cutsize in a small fraction of the total now."

Nov 1, 1995

By Henry E. Perlee

In a Bureau of Mines study two-dimensional mathematical equations were solved that describe the transient thermal response of a rock dust particle in a cloud of similar particles in a gas flame's preheat zone subject to a radiant field from the approaching flame. The description includes both radiant energy absorbed and emitted by the particle and thermal conduction inside the particle and into the surrounding gas environment moving relative to the particle. Two situations were studied; in one the radiant energy incident on the particle is converted to thermal energy at the particle surface, and in the other the radiant energy is converted to thermal energy uniformly over the volume of the particle. The result of the study showed that for a 10-µm-radius particle, a 200-mg 1-1 loading density, and a flame approach velocity of 30 m sec-1, the particle temperature rise was twice that previously calculated by Singer and Cook based on the model of Essenhigh and Csaba. It was further established that under the conditions examined a rock dust particle temperature never increases more than about 200 K before crossing the flame front.

Jan 1, 1976

By Donald P. Blasko

The Bureau of Mines investigated two areas of oil and gas seeps in the north-central Gulf of Alaska--Katalla River to Bering River and Cape Yakataga to Yakutat Bay to determine (1) whether previously reported seeps are still active, (2) the characteristics of the seeping hydrocarbons, and (3) the amount of bitumen contained in the drainage leaving the seeps and entering the Gulf of Alaska. Thirteen separate oil seeps, six bitumen deposits, and eight gas seeps were located, sampled, and analyzed. The oils ranged from 35.2° to 14.1° API gravity and had sulfur contents from 0.53 to 1.31 wt-pct. Bitumen samples had API gravities from 2.4° to 14.6° and sulfur contents from 0.28 to 0.88 wt-pct. Gas samples had specific gravities ranging from 0.577 to 0.883 and caloric values from 724 to 1,427 Btu/cu ft. A total of 63 water samples obtained from seep locations and seep drainages were analyzed by atomic absorption spectrophotometry for ionic content and by solvent extraction for hydrocarbon content. Although some of the water at the oil seeps had a bitumen content as high as 246,000 mg/1, the amount of hydrocarbons actually reaching the Gulf of Alaska averaged <0.2 mg/1.

Jan 1, 1976

By d&apos, Kathleen J. Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By Edward E. Johnson

The U.S. economy boomed in 1965, completing its fifth consecutive year of expansion. Although the advance was somewhat irregular, previous records for production, sales, employment, and income were topped. During the first few months of 1965, as the economy recovered from the depressing effects of the automobile strikes of late 1964, increases were unusually large. The gains moderated in early spring, but were stimulated at midyear by sharply rising capital outlays, excise tax cuts, in? creased Social Security payments, and accelerated Viet-Nam defense expenditures. Gross national product (GNP) in cur-rent dollars rose $49.5 billion or 7.8 percent, to a total of S681.2 billion. In constant dollars (effects of price changes eliminated), GNP increased 5.9 percent, a rate considerably higher than the historical postwar annual average growth of 3.5 per-cent. Demand increased in most final markets and was especially strong for business fixed investment and consumption expenditures. With the exception of construction, most of the increases in GNP were real, since prices increased less than 2 percent.

Jan 1, 1966

By O. C. Blade

Sales of diesel fuel in the United States exceeded 150,000,000 barrels during 1953 and 140,000,000 barrels during 1952. Following are some figures on the distribution of this fuel computed from data issued by the Bureau of Mines. 2/ [ ] Deliveries of diesel type fuel from refineries totaled 91,170,000 barrels during the first six months of 1954, 3/ a corresponding figure for 1953 was 86,284,000 barrels.

Jan 1, 1954

By R. P. Maloney

The economic viability of four depleted mines near Kennicott, Alaska, was determined by the Bureau of Mines to assess their profitability if they were developed today and thus estimate cost data for a medium-sized mine, mill, and town complex. This information should help the State and Federal Governments appraise the potential development of similar-sized mining operations in Alaska. Modern conventional mining and milling techniques were assumed, and I capital and operating costs were derived using flowsheets and standard costing methods. A total capital investment of $37.6 million was necessary to install a 1,000-ton-per-day shrinkage stope mine, flotation-type mill, and support facilities; capital requirements were divided about evenly among the three components. Operating costs, including labor, supplies, power, water, and &apos; indirect and fixed costs, totaled $42.79 per ton of ore; the mining accounted for nearly one-half the cost. To obtain a 12-percent discounted cash flow rate of return on investment, the analysis showed that the ore could be mined and milled, and the concentrate could be trucked via public roads to a dock facility in Valdez, Alaska, barged to Tacoma, Wash., and smelted and refined for 34.7 cents per pound for copper and 104.0 cents per ounce for silver. The average May 1972 price was 52.6 cents for copper and 158.3 cents for silver. The same set of data was used to examine the economic viability of the mine with the cost of constructing a private road from McCarthy, Alaska, To Valdez, Alaska. The 148-mile road added $53.3 million to the original capital costs and raised the required price of copper to 57.4 cents per pound and the required price of silver to 172.0 cents per ounce. The additional coat of building, maintaining, and paying taxes on a private road from McCarthy, Alaska, to Valdez, Alaska, would make this venture uneconomical.

Jan 1, 1973

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

The Bureau of Mines has developed a system using a high-speed electropneumatic mechanism for the rapid (grab) sampling of dusts and gases during an explosion. The sampling system consists of an aluminum housing that incorporates two 30-cm3 preevacuated glass vials with rubber septums. Upon actuation, the sampling probe needle is driven through the septum with a pressurized air pulse, filling the tube with gas and dust from the mine explosion. After a predetermined time, the sampling probe needle is retracted by a second high-pressure air pulse to its normal (quiescent) state, allowing the sampling tube to reseal. The onset and the duration of sampling are independently variable and controlled by a time-delay relay package. This technique enables the monitoring of pyrolysis-charring in coal particles and the generation and combustion of the pyrolysis vapors in both large- and small- scale explosions. The following results were obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Laboratory: (1) Gas sampling of the leading edge of the flame front shows the large concentration changes, characteristic of the flame front; (2) gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen; and (3) the particles collected in the flame zone show signs of extensive pyrolysis and charring.

Jan 1, 1988

By Hanns J. Billmayer

This report, which covers the period from June 15, 1974 to May 30, 1975, describes the work performed in compliance with the requirements of Contract No. H0242065 and modifications 1, 2, and 3 thereto. The purpose of the original contract was to equip the second shuttle car in the Jewell Ridge No. 12 mine, section 6R, with a refined design canopy and seats. In addition, several refinements and improvements were to be designed and installed at the same location on the cutter and the loader. However, during October 1974 in response to a request from the Technical Project Officer, the contract was modified to eliminate all of the cutter and loader tasks and substitute the design, fabrication, and installation of an improved canopy on the no. 2 roof drill in the above mentioned section of the Jewell Ridge No. 12 mine.

Jan 1, 1975

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point, out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1962 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1964

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1962 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1964

By A. D. Mah

To assist Bureau of Mines research in extractive metallurgy and to add to the thermodynamic data base useful to others, energy calculations were made for 63 reactions relating to investigations on the production of anhydrous aluminum chloride from chlorination of clay.

Jan 1, 1982

By A. J. Kraemer

[The Bureau of Minas for a number of years has been studying the properties of crude petroleum from producing fields in the United States and Western Hemisphere and has published a series of reports on these fields, including oil fields of Texas.5]

Jan 1, 1927