Search Documents

By Daniel Johansson, Markus Danielsson, Håkan Schunnesson

In sublevel caving, blasted material flows gravitationally into the drawpoint from above in a periodical manner. This type of flow behavior entails muck pile conditions that are variable along the course of extraction. The effect of this variability on the LHD (Load-Haul-Dump) operation in terms of loading efficiency and ability to undermine the blasted ring is not fully understood as of today. This paper presents results from a field test in LKABs Malmberget mine in Sweden, where the influence of fragmentation on the loading operation has been studied in detail. Drawpoint filming was conducted for extraction of two rings equivalent of roughly 10000 metric tons (~9842 long tons) of material each. The analysis includes fragmentation measurements, muck pile classification, and general estimations in terms of loadability. Further, an evaluation of LHD machines from two different manufacturers was conducted to identify and highlight differences. The results show that fragmentation, muck pile compactness, and flow characteristics are all interdependent. Flow disturbances and the subsequent loading of compacted fine material in the back of the ring have been identified as the main reason for occurring problems and prolonged digging times. However, the ability to sufficiently undermine the blasted ring has been identified to primarily depend on digging depth which is only observed to be high during flow disturbances. An absence of flow disturbances seem to promote high loading efficiency but simultaneously limit the maximum digging depth. A mid-range particle size distribution with a low amount of fines has proven beneficial for overall loading efficiency. The various LHDs employed showed significant variations in terms of ability to handle difficult loading situations (e.g. compactness, boulders, etc.).

Jan 1, 2018

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012

By Walter Voglauer, Elisabeth Zechmeister

Five serial photos show the first second of the demolition of a 75 m high, reinforced concrete tower in the 23rd District of Vienna, Austria. The tower demolition with high explosives was necessary because a 175t excavator could not finalize the destruction with mechanical tools. All mechanical works in preparation of the blast, such as the borehole drilling, were done by civil companies under the responsibility of the contracted demolition company PRAJO. The blasting itself was planned and executed by the engineer corps of the Austrian Armed Forces, Sunday, May 26, 2013. Nearly 800 boreholes filled with more than 100 kg of military plastic explosives were initiated with about 1,600 Austin electric delay detonators in exactly 1,000 ms and 30 steps of delay. The 10,000 tons of reinforced concrete tower fell as planned without any damage to the environment. Photo 5. The rest of the detonators initiate the water pools filled with high explosives forming a bizarre white water front to fight the following strong development of dust. The first 1,000 milliseconds are over.

Jan 1, 2015

By Khushaal Popli, Vanessa Roeland, Brian Hall, Carl Diederichs

Highland Valley Copper (HVC) has embraced an integrated Mine to Mill approach to comminution since the late 1990s. Previous blasting optimization was carried out through adjustments to blast pattern geometry (i.e., reduction of burden and spacing). This approach proved very effective and HVC reduced the burden and spacing of high energy ore blast patterns to what was considered the practical limit that still allowed for efficient drilling and bulk truck loading operations. While mining in the bottom of the Valley pit near the end of the previous pushback, HVC encountered high static groundwater conditions which enabled the transmission of elevated inter-blasthole pressures that had the potential to exceed safe operating limits for initiation products. This risk was mitigated through an expansion of burden and spacing for the high energy ore patterns, reducing the application of blasting energy and increasing the average particle size in Mill feed.

Feb 6, 2023

By Carlos Enrique Arroyo Ortiz, Jadir Pedro Alves

This paper presents some of the results obtained during the research work about the use of technologies and digital transformation in the process of rock drilling in open pit mines. The use of automation presents itself as a disruptive factor and a driver of improvements that provide sustainability in rock drilling. Seven main operational parameters were utilized to combine measurement while the drilling (MWD) with other information generated by the equipment during hole drilling, in six different lithologies in an iron mine, located in the central region of Minas Gerais in Brazil. Adjustments and corrections were made to the data collected in order to minimize external influences other than the rock itself, to ensure the effectiveness of the analyses. Finally, we sought to compare the performance of the drilling process in manual and automatic operation modes. Thus, making it possible to show the efficiency and impact on the sustainability of rock drilling operations in open pit mines.

Feb 6, 2023

By Sven-Erik Johansson, Gosta Rundqvist, Donald Jonson

In Stockholm a new road traffic system called Södra Länken (Southern Link) will be in operation in late 2004. The total length of the road system is 6 kilometres of which 4,5 kilometres run through tunnels under suburbs immediately south of Stockholm inner City. The new traffic tunnels together with existing Metro tunnels, which mostly are in rock, will be the determining factor for blast design for many projects in the future. To set reasonable and safe permitted vibration levels the Swedish National Road Administration, Stockholm Region and Stockholm Transport Rail System have together financed a project to determine guide levels for blast-induced vibrations in traffic tunnels in rock. The purpose of the project has been to establish guide levels that are appropriate for different types of rock tunnels.

Jan 1, 2004

By R. F. Favreau, Patrice Favreau

In many quarries and construction sites visited by the authors over the last 50 years, the latter have observed muck piles from blasting with explosives, which included numerous large blocks, in some cases of dimensions larger than the input to the crusher. The names of these sites cannot be given in the article because the owners insist that data obtained on such visits be kept confidential. Often the blasters felt that the natural fissures in the rock would compensate for the use of a low powder factor, and they asked the authors to explain why such blocks were present. A detailed analysis of the situation often indicated that the cause of the blocks is that explained by figures such as 6 and 7 below in the article.

Jan 1, 2018

By W B. Gregg

"A review, update, and expansion of Thiokol’s presentation at BAl’s Fiih High Tech Seminar titled ‘ADetonator - An Era of Precision in All-Electronic Detonators” is provided herein (and should be considered as a supplement to that publication). Thiokol is currently in the development and field evaluation phase of activities for our ACCUBLASTTM all-electronic detonator. The ACCUBLASTTM detonator uses a semiconductor bridge (an electronic match) in place of a conventional hot wire to initiate a safer, less sensitive material, titanium subhydride potassium perchlorate. The device is programmable to provide blast delays in one millisecond increments ranging from 1 to 500 milliseconds. The ACCUBLASTTM detonator combines an all-electronic programmable timer coupled with a semiconductor bridge to ensure detonation timing accuracy with +I00 microsecond precision. Initial development and field testing have been completed. These tests have verified ACCUBLASTTM detonators’ precision."

Jan 1, 1995

By Bruce R. Leland, Steven H. Smith, John D. Paulson

The USDA - Wildlife Services has been removing beaver dams with explosives for over 30 years. This paper will discuss the history of the explosives program, summarize how we've evolved, and highlight our work removing beaver dams in unique locations.

Feb 1, 2020

By Ken Eltschlager, J Silva Castro, J. M. Hoffman, Braden Lusk

This case study focuses on analysis of sounds inside a house induced by blasts as result of surface mining coal in West Virginia and how to better communicate technical information to the public. The field study included a house wide vibration and sound monitoring system installed in a home which was subjected to blasts at varied distances and direction. The structure response was separated into ground vibration and airblast induced movement due to the differences in their times of arrival. This signal was then compared to the sounds recorded to determine which component of blast (ground vibration or airblast) induced the maximum sound. Findings shows that blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast. While for blasts beyond this distance the maximum sound response was caused by ground vibration without exception. The kitchen generally created the most sound. The second phase of the study was to gauge the public’s response or preference to technical information. Three hundred and forty eight (348) telephone surveys were conducted in Logan and Boone counties West Virginia. Based on the survey, the public prefers units of pounds per square inch (psi) for airblast and millimeters of displacement for ground vibration. Ultimately a public relations plan was developed based on the results.

Jan 1, 2012

By Jon Hurt, Brent Meins, David Vardiman

"Two test blasts were conducted at the Sanford Underground Research Facility to establish optimum blast designs and to limit blast effects on existing research rooms and equipment in preparation for the largest deep underground excavation in North America. Located on the 4850 Level (4,850 ft below the surface)at the former Homestake Mine in Lead, SD, this excavation is part of the U.S. Department of Energy’sLong-Baseline Neutrino Facility that will house particle detectors for the international Deep Underground Neutrino Experiment hosted by Fermilab. A large array of seismographs was deployedthroughout the 4850 Level to measure ground vibrations and airblast pressures in tunnel drifts and in lab spaces."

Jan 1, 2017

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Elliott Giles

"Measuring a blast’s performance based on the bucket fill time or “diggability” has always been achallenge due to the subjectivity generally involved. The diggability of a blast is often based onopinions and speculation without the data to properly support the claim. This paper focuses howthe blast design can impact diggability and how it can be properly measured."

Jan 1, 2016

By Josh Calnan, Paul M. Holmgren, Abigail N. Styer

Detonating cord is a staple of the explosives industry, used widely in the civil and defense industries. Detonating cord is a thin, flexible plastic tube filled with pentaerythritol tetranitrate (PETN). It has many applications in mining, construction and military disciplines. For civil applications, it is used to connect and initiate a series of blastholes in a desired pattern. In the defense sector, it can be used as a detonating agent, a priming agent or alone as an explosive charge. Research has been done to understand the initiation and detonation physics on the detonating cord. However, its sympathetic detonation characteristics needed to be further analyzed.

Feb 1, 2020

By Travis A. Davidson, Ralph E. Burnham, Cathy Aimone-Martin, J. Kelly Ratliff

Blasters face a long list of tasks to execute daily—from vehicle inspections to blast design and layout, hole loading and tie-in, securing the site, and finally, safely executing the blast. Good practices and, in most cases, regulations and requirements necessitate documenting their work, specifically their blast report. While some blasters use paper forms, others use electronic means to streamline the process. The authors have served as attorneys and expert witnesses in representing companies and individual blasters in numerous administrative and legal matters in which documentation of the blaster’s work was both critical and detrimental to the effectiveness of defending their work. This paper discusses in a case-study manner the authors' observations concerning good blast report format, specific observations around electronic and paper report completion, record-keeping, seismograph setup and recordkeeping, video and photo documentation, internal auditing, and other topics related to documenting the blast. The paper aims to serve as a discussion guide for blasters to improve their blast record-keeping process, develop better practices that effectively document their work, and allow them to defend their work should a claim arise concerning their operations.

Jan 21, 2025

By Gordon K. Jorgeonson

Much of the modelling of blasting operations has been devoted to simulating blasts in open pit mines and quarries . This has been the most obvious application and has been reported in many papers and discussions in the past.

Jan 1, 1990

By Brian Sandhuas, Robert McClure

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one North American Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024

By Raymond V. Adolphson

Use of explosives effectively and safely has come a long way since its discovery and early stages of development. The need to objectively and functionally train personnel in the safe and effective use of explosives became forcefully apparent in the early 1930's in Forest Service work at the start of the Civilian Conservation corps program.

Jan 1, 1978

By S. S. Bud Jenkins

I went to an underground limestone mine recently to demonstrate the use of borehole liners. The liners were for horizontal holes in a normal “V” cut tunnel round. I hadn’t been in this mine for about 40 years. What a change. Way back they used cap and fuse and lit each fuse individually with a blowtorch. The face was about 40 feet wide and 14 to 16 feet high. They used ladders to get to the upper holes. The rounds were mostly slab rounds. I never saw this happen but had heard several times that the first holes were going off before the last holes were lit. I guess if this was true the use of slab rounds was a plus for safety. As far as I know they never had an accident but it was a scary procedure. There were a lot of scary procedures in the past and thankfully things have changed.

Jan 1, 2010