Search Documents

By S B. Richardson, R E. Danell, D Mead, N T. Moxon

Explosives provide a very concentrated source of energy which is often well in excess of that required to adequately fragment the surrounding material. Blast design, environmental requirements, production requirements and the lack of detailed insitu geological data generally limits the degree to which the explosive energy distribution within the blasthole can be significantly altered using, for example, different explosive formulations or variable loading techniques. However, increased flexibility can often be exercised over a blast through the use of air-decks.

Jan 1, 1993

By Janos Foldesi, Calvin J. Konya

The determination of the number of primers necessary to efficiently initiate an explosive column charge is essential to good blasting. If the number of primer is insufficient, the total energy stored in the main charge will not be released. On the other hand, the use of too many primers will be counterproductive and raise the blasting cost. Tests were conducted by the authors to determine the correct priming procedure for a basalt quarry. This paper describes the results of those tests.

Jan 1, 1976

By Mo Jadbabaei, Scott Harrison

There is very limited information available regarding the air pressures, flow rate, and velocity profiles in blast hole air drilling applications. Currently, many people are using incompressible flow correlation to calculate the bailing velocity. In this article, air pressure, flow rate, and velocity profiles are calculated using compressible flow theory. The airflow at the bottom of the hole is simulated using the jet flow theory. The concept of choking condition is introduced, and it is concluded that the velocity at the nozzle exit cross section cannot exceed sonic velocity. The minimum pressure required for achieving choked condition at the nozzle cross section is calculated. Choked and overchoked flow conditions at the nozzles are examined, and the maximum achievable cleaning power is correlated to the nozzle size and pressure.

Jan 1, 1999

By P D. Kasbanis, Lyall Workman

The energy output of an explosive is typically calculated using an equation of state and computer applications. Results are reported as weight and bulk strength, either in absolute terms or relative to ANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of "available energy" associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated.

Jan 1, 1996

By Gregory S. Parker

The explosives community has seen tremendous technological advances during the past several decades. When this industry was in it's infancy and even past, Powder Monkey's defied the odds by relying on daring and cunning to unleash the power contained in nitroglycerin and black powder. Unlike the manufactured improvements, there has been little in professional evolution amongst the blasting fraternity unless provoked (for the most part) by the government. It is the intent of this author to advance the cause of an industry wide training and certification program, uniform in nature and broad-based enough to be voluntary, giving states whose outstanding programs are already in place, the opportunity to provide input. In creating this type of atmosphere, grandfathering, reciprocity and accessibility would be paramount. With ISEE taking a firm leadership role during the inception and NICET's involvement in the administration, the idea postulated here is intended to spark interest and debate, bringing the inception of such a program to the forefront.

Jan 1, 1995

By Jeff Hermanson

Every construction project has site specific problems that need to be dealt with. These problems may be created by the geology, location, weather, time constraints, etc. Once these problems have been solved their solution often can be transferred to other similar construction sites. The Crazy Horse Memorial project is no exception.

Jan 1, 1996

By J S. Kuszmaul

The economic development of modified in situ oil shale retorting will benefit from the ability to design a blasting scheme that creates a rubble bed of uniform permeability. Preparing such a design depends upon successfully predicting how a given explosive will break rock. Numerical models are used to make predictions of the extent of damage caused by an explosion.

Jan 1, 1985

By Albert van Niekerk, Mick Lownds

Overview of the UNI Tronic™ Electronic Blasting System

Jan 1, 2004

By Larry R. Fletcher, Virgil J. Stachural, Matthew N. Plis

The Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of a series of tests to improve presplitting at a western surface coal mine. Reductions in overbreak were achieved by decoupling and/or repositioning the main explosive charge in the 10-5/8 inch presplit blastholes that formed the highwall. Blast designs are presented by the authors for 1) repositioning the explosive charge from a weak rock layer to a stronger rock layer, 2) decoupling with cardboard tubes in the toe region, and 3) suspending bagged powder at intervals along the length of the blasthole. About the same total quantity of explosives was used in all three test designs. It was readily apparent from periodic visual examination and photographic surveys of the highwalls that the amount of rockfall was reduced, and with a longer delay before rockfalls began, in all test areas.

Jan 1, 1991

By J. Esterle, J. Kruttschnitt

Fragmentation modelling in soft rocks presents a challenge due to their propensity to further fragment after blasting during normal handling. Coal and some iron ore deposits are examples of materials that undergo significant degradation during the extraction, hauling and dumping process of the mining operation. The Kuz-Ram model is an empirically derived predictor of size distribution from blasting hard rock. Little breakage occurs during excavation and subsequent sizing of hard rock, so the measured Run of Mine (ROM) size distribution is essentially the same as the post-blast (before excavation) size distribution. However, for soft rocks, each step of the excavation and hauling operation imparts energy to the rock particles so the measured. ROM size distribution will be significantly different from the postblast size distribution. In order to calculate the ROM fragmentation at any stage of the extraction (or sizing) operation, the JKMRC has developed a model that combines both blast fragmentation and degradation through subsequent handling.

Jan 1, 2001

By TA Louw, Dr CM Lownds

In an era where profits are constantly being eroded, mines are looking towards technology developments to assist them in solving mining problems and reducing mining costs. An emerging technology that could assist mines in becoming more cost effective is electronic detonators. Electronic detonators have been under development for several years. Over the past three years, the spotlight has fallen on commercial use of electronic detonators and the extent to which the promise of precise and programmable timing can assist mines with their environmental and productivity problems. This paper uses case studies to demonstrate both surface and underground applications where electronic detonators and blasting systems were used to solve typical mining problems such as vibration and fragmentation. Safety aspects such as hanging wall conditions and high wall stability also benefited from the use of electronic detonators. The paper also demonstrates how the use of accurate electronic detonators and blasting systems has resulted in improved/more even fragmentation with further downstream efficiencies. These efficiencies may include increased cast percentages, reduced oversized rocks, quicker cleaning times and increased production rates.

Jan 1, 2004

By J Edmund Hay

Previous work by the Bureau of Mines to develop a test for determining the initiating strength of commercial detonators has been modified and extended. Recently reported results by the Bureau used a homogeneous liquid explosive to avoid the complicating effects of inhomogeneities; however, due to the belief that there may be essential differences between the initiation mechanisms of simple liquids and multi-phase mixtures and the fact that almost all commercial explosives are in the latter category, the experiments have been modified accordingly. The acceptor explosive is now a mixture of explosive-grade ammonium nitrate (AN) prills, methanol (MeOH) and nitromethane (NM). An additional change has been the use of the United Nations (UN) cap sensitivity test configuration in which the detonation witness is the degree of compression of a lead block, which is a quantitative measure of the response of the explosive. Results indicate that this mixture has sufficient range of sensitivities to be useful in comparing the strength of commercial electric detonators.

Jan 1, 1993

By F O. Otuonye

Full-face blasts were fired in a 12 x 8 ft drift of an underground hardrock mine in a basalt formation with porphyry copper to study the effects of drill pattern and explosive type on the size distribution of the resulting muckpile. Each muckpile produced by five full-face blasts was sampled four times with a scooptram equipped with a 5-cu yd bucket and the size distribution of the broken rock in each bucket was determined by screen analysis. Results show a strong dependence of the fragment size distribution of muckpile on the blast pattern and explosive type for a given rock type. The mean fragment size of the broken rock was compared with the predictive equations of other investigators. Random sampling of the muckpile from full-scale blasts and screen analyses of the samples are recommended in assessing the size distribution of the broken rock because of scaling errors that are inherent in full-scale blasts when designed from results of small-scale tests.

Jan 1, 1985

By J J. Mullay, G W. Anderson, C J. McFinley, J F. VanNorman, C J. Kefer

Previous work has shown that testing of precompression effects conducted on a small scale under simulated field conditions in actual rock provides a reasonable model for the evaluation of explosives and initiators under the adverse conditions encountered in production blasting. Using this methodology can result in greater understanding of the phenomena as well as the ability to predict performance. This effort has been extended to evaluate various parameters not previously studied in a controlled fashion. The present paper describes the use of this technique to study the effects of delay timing on precompression effects. Intervals from 25 to 150 milliseconds are included in the study. Both VOD measurements and damage estimates are utilized in the evaluation. The results demonstrate that timing delay between holes is quite important in determining the overall effectiveness of a blasting program.

Jan 1, 1994

By Alan Hooper

This paper and slide presentation is a brief rundown on what is probably the worst natural devastation I have ever witnessed. The epicenter of the quake that so violently shook Mexico City occurred 230 miles away near Mexico's west coast. The first calculation placed the quake at 7.8 on the Richter scale. This was later upgraded to 8.1. Each unit increase on the Richter scale indicates about a 30 fold increase in energy released. The quake was felt in much of Mexico and south Texas and damage occurred in many other Mexican cities. On the morning of September 19, 1985, at 7:18 A.M., the ground went into motion and shook for approximately 2 to 4 minutes. During this period most of the devastation occurred. At 7:38 P.M. the following day, the second quake hit and more buildings fell from this 7.5 quake. The ground in Mexico City moves like jello since it is a dry lake bed 7,350 feet above sea level.\

Jan 1, 1986

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

In March of 2001 Barrick Goldstrike Mines, Inc. began evaluating the potential benefits of electronic detonators at the Betze Post open pit gold mine. The original evaluation focused on increased fragmentation, and excavator productivity. During the original evaluation there was an attempt to quantify mill throughput. Early tests indicated that there would be a benefit to mill throughput, however management was hesitant to take on the added cost of electronic detonators based on the initial evaluation. In early 2002 a decrease in mill throughput was being forecast as a result of harder ore being encountered. As a result of the initial electronic detonator evaluation a team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative. This initiative was targeted at improving mill throughput as the harder ores were encountered. Batch tests were conducted to determine if adjustments to drilling and blasting in the open pit could increase mill throughput and justify a 50% increase in drilling and blasting costs for the harder ore material.

Jan 1, 2004

By Thomas L. Linton

The results of an extensive literature review and field experiments regarding the effects detonation of high energy explosive have upon various aquatic organisms are reported. These results were used to modify regulatory permitting criteria in Texas. Three separate field experiments were conducted. In the first study, surface placed charges were used in a marine habitat. In the other two, the charges were placed in drilled holes. In one, which was in a freshwater environment, the drilled holes were filled with drilling mud after placement of the charges. In the second, which was in an estuarine environment the holes were allowed to sit for thirty days prior to detonation to permit natural back-filling to occur by water transported sediments. A variety of aquatic organisms held in wire cages were exposed to detonations. Immediate and long-term effects of the exposure were determined based on external and internal visual observations. Damage to aquatic organisms was found to be reduced by placing the explosives in drilled holes and back-filling the holes prior to detonation of the explosives.

Jan 1, 1997

This paper presents a brief discussion of three case histories to illustrate several aspects of the question of blasting in or immediately adjacent to concrete. The results demonstrate a need to make dramatic upward revisions in previous criteria, whether it be the standard particle velocity criteria or damage response spectra bounds, - especially those which include conservative upper limits of constant acceleration for the high-frequency portion of the spectrum. It is demonstrated, also, that conventional off-the-shelf blast-monitoring instruments are not capable of monitoring small blasts at close range. Both the frequencies and the levels of effect are beyond the range of such instruments. These case histories suggest further that there is a need to review the applicability of certain wellknown equations of elasticity.

Jan 1, 1980

By Mario Karfakis, G. Langlois

Well stimulation is the process by which any production well, whether for production (extraction), storage (injection) or deep interaction (remediation, monitoring, etc) can be made or stimulated to flow at higher levels. This stimulation is driven by active methods to increase the permeability in the near-well environment and create a larger zone of communication between a well and the reservoir it services. Well stimulation is a crucial aspect of well completion and reservoir engineering and is a subject of careful pre-drilling planning. In many modern industrial endeavors the effectiveness of well stimulation is often critical to economic viability. Because of the broad impact of well engineering on several large industries (petroleum and natural gas extraction and storage, geothermal power, groundwater monitoring, extraction and management, environmental remediation, mining and minerals extraction, etc.) changes in the state of the art in well engineering and well stimulation can affect the capabilities of very diverse and disparate industries. This paper is an effort to communicate the status and effectiveness of current practice and technology in well stimulation. The intention being that effective communication of progress can spur innovation in industries that require well stimulation but are removed from immediate communication of technological or practical improvement.

Jan 1, 2009

By Jerry R. Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (11-14 million cubic meters) of gas per day.

Jan 1, 1996