Search Documents

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014

By S. Safak

Europe retains a modest position in world mining activity in terms of scale of production and mineral reserves but maintains a non-negligible role in the world mining industry. The concept of sustainable development resting on three pillars of economics, environment and social development has become an increasingly important factor in the European mining sector and a major influence on the related policies of the European Commission. Members of European mining industry shall conduct their activities according to the principles which promote sustainable development. A successful minerals planning policy should create the legal administrative environment that is necessary to ensure the sustainable supply of minerals to society within the framework of sustainable development. Members of the European mining industry shall conduct their activities according to principles which promote sustainable development. The challenge for sustainability is to find a balance between securing minerals supply, protecting the environment and achieving social progress. The point of balance depends on the range of policies adopted by governments. In this paper the development of the sustainability of the mining sector in EU and the social component of sustainability in the mineral industry is discussed.

Jan 1, 2014

By Ruiyang Zhang, Ping Fang, Dezhou Wei, Shuling Gao

A CFD based numerical simulation of flow characteristics of hydrocyclone was conducted with different structural and operational parameters to investigate its distribution characteristics and influencing mechanism. The results show there exist several unsymmetrical envelopes of equal vertical velocities among both upward inner flows and downward outer flows in the hydrocyclone, and cone angle and apex diameter have remarkable influence on the vertical location of the cone bottom of the envelop of zero vertical velocity. It is also found that some tangential velocity isolines exist in the horizontal planes located in the effective separation region of hydrocyclone, and feed pressure has almost no effect on the distribution characteristics of both vertical velocity and tangential velocity of flow in hydrocyclone, however the magnitude and gradient of tangential velocity are made increased obviously, so as to make the high density particles motion velocity to the wall increased and to make the cyclonic separation effect improved. The simulation results also show when the apex diameter increased, the pressure of the fluid field decreased, however the pressure grads in the apex district increased, and the degree of changing is different as the cone angle, which showed some interactive influence of cone angle and apex diameter on the fluid field of hydrocyclone. While the feed pressure also has almost no effect on the pressure distribution characteristics, however the its magnitude and gradient are made increased accordingly, which can improve the separation accuracy according to particle density.

Jan 1, 2014

By S. M. Javad Koleini

The aim of this research is to extract zinc from complex lead and zinc ore containing carbo- silicate lead and zinc minerals using sulphuric acid. Samples, taken from Dareh Zanjireh mine located in central of Iran, were subjected to leaching tests after calcination process. Experiments were planed according to the Taguchi statistical method. The calcinated samples contain 13.98% zinc and the constituting minerals being dolomite and zincate. Various parameters such as speed of mixing, temperature, time, solid to liquid ratio and pH were studied. A solid to liquid ratio of 1:6 gr/mL at 60°C and 800 rpm speed of mixing for 30 minutes resulted in a product with 85.96% zinc recoveries.

Jan 1, 2014

It is well known that the crushing and grinding steps in the mineral processing of ores represent a substantial proportion of total energy, cost and carbon emission in mining. For instance a recent study calculated that 36% of the energy consumed by gold and copper producing mines in Australia was attributable to comminution (Ballantyne et al, 2012). Understanding this component of a business is essential in a world seeking to lower production costs, improve earnings and reduce its carbon footprint. The issue commands the attention and support of industry leaders in the mining sector, government, equipment manufacture, engineering design and research organizations. Furthermore, several researchers have often stated that globally, comminution processes consume between 3-4% of the world?s electrical energy production (Daniel and Lewis-Gray, 2011). In 2009-10, Australia?s Federal Government Energy Efficiency Opportunity (EEO) participants in the mining sector used 336.5 PJ, representing approximately 6 percent of Australia's total energy use. It is evident that the current practices of breaking rocks in tumbling mills are relatively inefficient (Fuerstenau and Abouzeid, 2002). Research and improved engineering design has established that a range of improved blasting, crushing and grinding techniques and flow sheets may lower project costs and carbon footprint. These include relatively simple process flow sheet strategies such as gangue rejection or pre-concentration prior to size reduction, a better combination of grinding technologies (both current and new systems), and selection of coarser grind sizes where ore and waste mineralogy allow. Yet, despite this systematic and detailed research, the industry remains somewhat reluctant to implement these strategies. CEEC (Coalition for Eco-Efficient Comminution) was established in 2011 to support knowledge sharing and change in an area of high-energy consumption for the global mineral industry. CEEC is a not-for-profit industry company, funded by grants from world wide industry companies, whose mission is to accelerate knowledge and technology transfer in the field of energy-efficient comminution. The key benefit to the mining sector arising from CEEC?s activities will be an increase in the rate at which more energy-efficient comminution data sets, processes, and technologies are developed, demonstrated, shared and applied. This will contribute directly to the industry?s target of reducing operating costs and carbon emissions. CEEC International Ltd and JKTech Pty Ltd teamed together to facilitate the inaugural CEEC Workshop, in June 2012. The purpose of the workshop was to produce a roadmap to provide guidelines for how (1) operations can achieve best EEC practice in the short to medium term, in collaboration with vendors, engineering companies and other service providers, and (2) what R&D is needed to achieve paradigm change in EEC in the medium to long term, e.g. 75% reduction in comminution energy in 10 years.

Sep 1, 2012

By S. Gaydardzhiev

Initial experiments towards preparation of hollow ceramic microtubes by dip-coating of fibrous plants with water based alumina gel-casting slurries using hemp and coconut fibres as templates have been done. It has been found that the wettability of fibres and accordingly the stability of the developed ceramic layer on their surface during slurry gelation varied significantly within the different fibre types. Good correlation between the diameters of the template fibres and the resulting channels has been found at the level of solids loadings used, 31 %. Hemp fibres used as bundles have led to formation of multi channel patterns while the coconut fibres-templated process resulted in uniform monochannel materials. The micro tubes have show good mechanical handling.

Jan 1, 2014

By Sanja Miskovic, Manjunath Basavarajappa

In this study, a coupled CFD-DEM (Computational Fluid Dynamics-Discrete Element Method) approach is used to simulate two-phase, solid-liquid flow within the flotation cell. Turbulence plays a key role in flotation cells and level of turbulence is affected locally by the presence of particles. Turbulence in the flow is modelled using Reynolds Averaged Navier-Stokes (RANS) based k-e model. Using particle transport and spatial distribution, mixing mechanism for differed sized particles are analysed. By including the effects of particle-particle collision, particle rotation, and particle translation, as well as the volume occupied by the particles in the fluid, CFD-DEM approach can be used to accurately predict the motion of particles in the turbulent solid-liquid flows with strong coupling. Electrical resistance tomography (ERT) is used to investigate the effect of impeller size, shape, off-bottom clearance and impeller speed on mixing and suspension behaviour inside flotation cell. The effect of flotation impeller design, impeller size, and off-bottom clearance on flow hydrodynamics is investigated. In the case of moderate and high solids loading (> 10 %w/w), energy is dissipated through inter-particle interactions and four-way coupling becomes important (Derksen 2003). The main goal of this study is to understand the effect of particle size and concentration on flow dynamics at high Re in highly turbulent systems using advanced modelling and measurement techniques. Experimental measurements obtained by ERT) system allowed detailed mapping of temporal hold-up profiles of the dispersed phase. Impeller size and off-bottom clearance are found have significant effect on the particle suspension characteristics.

Jan 1, 2014

By W. Pawlos

"The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images.Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement. The outlet level of a grain of the same physical properties from the separator is a random variable with normal distribution which modal value is equal to the outlet level of a spherical grain, calculated from the solution of grain movement equations. At these assumptions it is possible to calculate the height of the passage from the separator working chamber to separate a given product with a given separation accuracy, measured by a probable error and to determine separation conditions."

Jan 1, 2003

By Richter, E. Charikinya

"Mineral processing unit models require information on particulate properties such as particle size, solids flowrate and mineralogical composition to model their operations. Process models that describe the separation process can be classified based on the level of information required from the ore, i.e. the feed stream to the separating unit. The most comprehensive level of mineral processing models is the particle-based modelling approach. Particle based modelling describes a modelling approach where mineral composition, mineral liberation and textural information of particles making up the process streams is used in modelling. The advantage of this approach is that all model streams carry particle level information (size, liberation, shape). This information is obtained by applying automated mineralogy techniques such as Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) analysis which provide accurate and detailed information on process stream particle properties. Currently the use of liberation information in modelling and simulation is rare, due to the limited number of separation models that liberation data as input. The objective of this study is to develop a particle based model for a dry magnetic separator, where mineralogical information is used directly to simulate a dry magnetic separator operation. Magnetic separation tests were carried out on high, medium and low grade magnetite ores using a laboratory magnetic separator. Streams from the separator were sampled and sized for chemical and liberation analyses. A sized mass and elemental balance around the magnetic separator was carried out. The elemental assays of each stream were converted to mineral quantities and a sized mineral balance was done. QEMSCAN measured liberation data was reconciled to the mineral balance based on mineral quantities obtained from chemical assays. This was followed by the development of a particle based model that calculates the trajectory of a single particle based on its mineral composition and textural properties. The model was tested on experimental data and was able to predict the effect of variation in process feed stream mineralogical attributes (liberation, grade, particle size) on magnetic separation performance. Results of this study highlight the benefits of the particle based modelling approach. INTRODUCTION The extraction of mineral values from ore requires liberation of the value minerals from the gangue followed by their separation. Liberation is achieved by size reduction operations (Desmond, 2008; Fuerstenau and Abouzeid, 2002). Separation of gangue material from value mineral takes place in various mineral upgrading stages such as classification, magnetic separation and flotation. In these concentration stages value minerals are separated from gangue minerals based on the physical properties of the ore particles making up the feed such as size, liberation, volume of magnetic material and density. The success of separation is related to the liberation of the feed particles, the performance of the separation technology applied, as well as the inherent characteristics of the feed material (Leißner et al., 2013)."

Jan 1, 2018

By K-O. Mickelsson, S. Töyrä, H. Esbensen

Accurate information of physical, chemical and metallurgical quality characteristics such as moisture content, iron grade and particle size are crucial for successful process control and for producing products within customer specifications. Correct moisture content of pellet feed is an important variable for successful balling of iron ore pellets and to minimize power consumption in the sintering process. Control of the filtering process in the pelletizing plant is therefore essential for both productivity and high product quality. The current measurement systems for moisture content at LKAB are based on two types of manual grab sampling, subsequently analyzed with rapid moisture determination methods. Previous studies of the measurement systems have indicated high sampling variability resulting in lowered possibilities for successful process control. The objective of the present study is to evaluate an alternative filter sampling approach and testing of on-line Infra-Red analysis (IR-analysis). On-line IR-analysis has the advantage of eliminating physical sample extraction and allowing for continuous monitoring of moisture content. However, this approach is sensitive to the surrounding environment, making careful calibration and control crucial for the quality of measurement results. Furthermore, as IR-sensors only target the surface of the conveyed pellet feed, several incorrect sampling errors need to be considered and counteracted to eliminate sampling bias and reduce the remaining measurement variability. Variographic characterization was applied to the two current grab sampling approaches of combined filtered material, to the alternative filter sampling method, and to the On-line IR-analysis. The results indicate that both the sampling of separate filters (using composite sampling and ISO-standardized moisture analysis), as well as a calibrated and well- maintained IR-sensor can improve the relative variability significantly, by lowering the total measurement system variance from 60% to 25%.

Jan 1, 2018

By Daniel Saramak

"Issues concerning effectiveness of the high-pressure comminution process in technological circuits of copper ore treatment were presented in the paper. Crushing processes taking place in high-pressure grinding rolls devices (HPGR) are currently one of the most efficient methods of hard ore size reduction in terms of the energy consumption. The HPGR products are characterized by a fine particle size and the micro-cracks formation in individual particles, which appear in downstream grinding processes, decreasing their energy consumption. The purpose of this paper was to analyse the effectiveness of a ball mill grinding process depending on the changeable conditions of run for the HPGR crushing process. The research programme carried out included crushing tests in the laboratory scale HPGR device at various settings of the operating pressure volume and selected qualitative properties of the feed material (i.e. particle size distribution). Particle size distribution analyses of all HPGR products were performed and in the next stage the material was a feed to the ball mill grinding process. Grinding process kinetics were investigated through the determination of mass recoveries of individual particle size fractions after defined grinding time intervals. The models, defining the grinding process effectiveness as a function of changeable conditions of HPGR process run, were determined on the basis of obtained results. Based on these models the optimal grinding time in a ball mill was specified which is, in turn, the basis for optimization of operation of the technological comminution circuits for a given material type. The obtained results proved that the application of HPGR devices in a given copper ore comminution circuit may improve the effectiveness of the downstream grinding process which leads to improvement of the entire circuit work efficiency through decreasing the process energy consumption and enhancing product size reduction."

Jan 1, 2014

By Bent Babel, Martin Rudolph

"The characterization of reagent-mineral interactions in flotation systems of finely intergrown ores holds difficult challenges for the applicability of standard techniques like Hallimond tube tests and contact angle experiments or renders them impossible due to a lack of sufficient samples in terms of quality and quantity. This disadvantage may not apply to more sophisticated techniques, but these often do not work in an aqueous environment. We present the utilization of an atomic force microscope with a hydrophobic colloidal probe to characterize the wettabilities of individual mineral domains of an ore sample, while additional spectral information is gathered by Raman spectroscopy. The exemplary ore sample investigated is mainly containing cassiterite and quartz, therefore the reference measurements like Hallimond tube tests and contact angle experiments were carried out with this binary system as a comparison. The focus of the study lies in the correlation of data gathered by the atomic force microscope and the Raman spectrometer with data from standard techniques. Finally, the applicability of the colloidal probe atomic force microcopy technique for reagent-mineral investigations is critically evaluated.INTRODUCTIONThe focus of this paper is the application of colloidal probe atomic force microscopy (CP-AFM) for theinvestigation of reagent-mineral interactions on a binary system of cassiterite and quartz. This and similar concepts using hydrophobic AFM probes have been applied by multiple authors (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b; Wada et al., 2017; Xie et al., 2017). The hydrophobic interaction is the main interacting mechanism for the hydrophobic colloidal probe with hydrophobic sample surfaces and the long range attractive component has been accounted to nanobubbles on the interacting surfaces (Yakubov et al., 2000). More detailed information on nanobubbles are available in two reviews compiled by Attard and Hampton (Attard, 2003; Hampton and Nguyen, 2010). This paper is based on the work by Rudolph and Peuker comparing different AFM based measuring concepts, additionally gathering data with Raman spectroscopy and correlating results of microflotation and CPAFM measurements (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b)."

Jan 1, 2018

By C. A. C. Sequeira, G. N. Anastassakis

"The separation of fine or even smaller size mineral particles with conventional methods is inefficient due to the specific properties of fines (small mass, high specific surface area, and high surface energy per unit area). Hence, the production of high-grade concentrate with high recovery is very difficult to impossible and a significant share of mineral values is lost to the tailings. The aim of the current research is to investigate the possibility to efficiently separate value minerals from gangue of fine particle size. The objective of the current work is to develop separation schemes of fine mineral particles by combining an initial stage of particles agglomeration with the use of collectors (hydrophobic agglomeration) with a subsequent conventional separation method. In the current research, magnesite was used as mineral value to be separated: a) from quartz, and b) from mineral mixture (serpentine, ilmenite, and olivine). In each case, tests on single minerals and artificial mixtures were carried out. After hydrophobic agglomeration, the separation of magnesite from quartz was achieved by settling; in the second case (gangue: serpentine, ilmenite, and olivine), magnetic separation of the co-agglomerated gangue was applied. In both cases, the results of the preliminary tests on single minerals suggest that the separation of mineral value is feasible and efficient. These findings were also confirmed from the results of the tests on artificial mixtures of magnesite and gangue, either quartz only or mineral mixture. Both separation schemes provided with magnesite concentrates of commercial grade (95% magnesite) with high recovery. INTRODUCTION The generation of fine particles is inevitable in many operations of mineral commodities processing. Especially in the case of low-grade ores, the mineral value is finely disseminated in the ore, and considerable liberation occurs at a fine size range. Although there is not a uniform classification system with respect to mineral particles size, fines are usually characterized the particles with a size range of -100µm+20µm, very fines those of -20µm+5µm, ultra fines of -5µm+1µm, and colloids smaller than 1µm (Sivamohan, 1990)."

Jan 1, 2018

By Ashiwani Kr Gupta

The floatability of coal is affected by the presence of dissolved inorganic ions in plant process water. Water quality is characterized in terms of conductivity, hardness, turbidity and composition of oil. These quality indices are correlated with coal flotation performance for three different water named, ?R&D laboratory tap water?, ?process untreated water? from West Bokaro wahsey-2 Tata Steel, India and ?process treated water? after passing laboratory developed treatment process. The study clearly indicated that a significant quantity of clean coal is being lost due to poor process water quality used in the flotation process. The laboratory investigations showed that if these dissolved salts and suspended solids are reduced to even 50%, a clean coal yield improvement by minimum 5%~10% at the same ash level could be expected. Therefore, the conventional practice of water recycling though a thickener or a tailings pond needs a complete re-look. The water treatment process for recycled water has also been discussed for improving the process water quality as well as enhancement in flotation performance efficiency.

Jan 1, 2014

By Emile Scheepers, Chris Aldrich, Jacques J. Eksteen

The pneumatic injection of CaC2 powder into molten iron has become a very reliable and effective way to carry out desulphurisation. The key variables that influence the kinetics of this process are the condition and composition of the top slag, the oxygen activity in the hot metal and the injection conditions. Notable injection parameters include carrier gas flowrate, reagent flowrate, lance depth and initial sulphur concentration. A one-dimensional, steady-state model for momentum, heat- and mass transfer in rising gasliquid- powder plumes was developed for conditions relevant to the CaC2 refining process at Saldanha Steel?, South Africa. Combined with a model that predicts the contribution of the topslag to the process, the overall rate of desulphurisation as a function of time was determined, thereby quantitatively demonstrating the influence of the above-mentioned injection parameters on the kinetics of the desulphurisation process.

Jan 1, 2003

By Francisca San Martín, Martin Rudolph, Willy Kracht, Tomás Vargas

It has been shown that bacteria Acidithiobacillus ferrooxidans can be used to depress pyrite in seawater flotation at natural pH, which opens the possibility for its use as an alternative to lime to depress pyrite in copper sulfide flotation. In order to have a better understanding of the mechanisms involved in pyrite depression with A. ferrooxidans, an exploratory experimental campaign was carried out, including attachment density and contact angle measurements, and the effect of adding bacteria before or after collector. Biodepression of pyrite improves when increasing pH from 3 to 8, with a decrease in recovery from 92% to 36%. This increase in depressing capability is accompanied by an increase in attachment density, from 2.58×108 bacteria/g to 1.99×109 bacteria/g at pH 3 and 8, respectively, suggesting that the mechanism of depression is related to the attachment of bacteria to the pyrite surface. It was observed that the conditioning sequence with collector and bacteria influences the biodepression capacity of A. ferrooxidans. Having as a reference a value of pyrite recovery equal to 97%, when using only xanthate in seawater flotation at pH 8, the effect of both conditioning with bacteria-followed-by-xanthate and xanthate-followed-by-bacteria were assessed. When bacteria were added before the collector, the recovery of pyrite decreased to 36%. On the other hand, when bacteria were added after collector, the recovery was 64%, showing that biodepression of pyrite with Acidithiobacillus ferrooxidans is more efficient when the conditioning is carried out first with bacteria. The contact angle values show that there is little effect of the second component added to the system, i.e., if pyrite is first conditioned with bacteria, the contact angle does not change significantly once the xanthate is added (bacteria-followed-by-xanthate). The same was observed when the conditioning sequence was xanthate-followed-by-bacteria.

Jan 1, 2018

By Stefaan J. R. Simons, Michael T. Spyridopoulos

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, has been investigated. We formed two bubbles of equal size and forced them to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. We present data of coalescence frequency and time, as well as images of the coalescence events.

Jan 1, 2003

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

By Sergio Castro, Janusz Laskowski

In the flotation in highly concentrated electrolyte solutions not only ionic strength but also chemical composition, flotation pH and mineral properties play an important role. As a result an improvement or depression may be observed. A strong improvement in the floatability of hydrophobic bituminous coals and other inherently hydrophobic minerals is characteristic for the "salt flotation process", which is carried out in concentrated electrolyte solutions at natural pH and without addition of any flotation reagents. However, pH is a key factor when saline and hipersaline waters with hydrolyzing metallic ions are used as process water. In the case of flotation of Cu-Mo sulfide ores in seawater, molybdenite is strongly depressed by the Mg2+ hydrolysis products when pH is raised to depress pyrite. Process water with a high content of Mg2+ and Ca2+ ions, and this also includes seawater, have deleterious effect on the anionic flotation of industrial minerals with fatty acids. The flotation of potash ores is carried out in NaCl-KCl saturated brine (6-7 mole/L of NaCl and KCl) with the use of long-chain amines. Such a high electrolyte concentration changes dramatically the amine Krafft point making the collector insoluble in brine; its mode of action entirely differs from that in conventional flotation processes.

Jan 1, 2014

By Kari Niiranen, Andreas Fredriksson

LKAB (Luossavaara-Kiirunavaara AB) is operating iron ore mines, concentration plants and pelletizing plants in Northern Sweden. Geometallurgy, which combines geological and metallurgical information is not a new way of thinking at LKAB, but rather a revised and updated version of an old working process. A project called "Silica in the Mine" which started in 2007, was an important reason to set a new focus at the geometallurgy. The target of the project was to develop a simplified method in laboratory scale to predict SiO2 grade in the magnetite concentrate in Kiruna and further predict the physical properties of the crude ore with respect to processing characteristics. The connection between mineralogy and products properties have started to be even more vital and necessary to examine due to the future exploiting new iron ore deposits. Geometallurgy at LKAB can be described as a mental and strategic framework where the Research and Development department (R&D), and others within the organization of LKAB, aims towards the connection of the minerals-production-products. It could in its basics be called "research & development", but it must be clarified that changes have been made, mainly due to the development on the instrumental analysis side. LKAB’s idea is to work quite broad, with internal educations, an active working process in ongoing projects, together with external parties (such as universities), with several PhD-projects and an upgrading on the instrumental side at the LKAB Research & Development department. This paper is a summary about the concept Geometallurgy at LKAB and some of the actions within its framework.

Jan 1, 2014