Search Documents

By Mahdi Soudkhah, Akhter Hossain

Vertical micropiles are generally considered to be low in lateral resistance. Therefore, battered micropiles are often used when additional lateral load carrying capacity is required. However, battering of micropiles can sometimes be restricted due to existing adjacent structures or utilities, especially in highly urbanized areas. For example, presented in this paper are lateral load test data from a 43-story building project in New York City where vertical micropiles were used due to proximity to adjacent structures. Three static lateral load tests were conducted on micropiles consisting of 13.375-in-outside diameter and 25- to 51-ft-long casings, and socketed 10 to 12.6 ft into the bedrock (gneissic schist). The subsurface profile above the bedrock consists of loose to very dense, mostly sandy and silty soils. The design load for the three test piles was 14,000 lb and the maximum load applied during the tests was 200% of the design load. Lateral load- displacement behavior of the free pile heads from the load tests are compared with the results of p-y analyses based on a widely used p-y method for sandy soils and using a lower and an upper bound estimates of soil index properties and strength parameters. Since the existing p-y curves were formulated for larger diameter driven piles at a specific geographic location, major differences are observed between the results of the load tests and the p-y analyses. In general, the lateral displacements estimated based on the p-y analyses using upper bound soil parameters are relatively closer to the results of the field load testing. Modified p-y curves specific to the sandy and silty soils representative of the general subsurface conditions of New York City matched with the lateral load tests are presented in this paper. INTRODUCTION Micropiles generally are limited in lateral load carrying capacities due to their relatively higher slenderness ratios (ratio of depth to diameter) compared to more conventional deep foundation alternatives, such as driven piles and drilled shafts. So, micropiles are not typically considered as deep foundation solutions when significantly high lateral loads are expected on the substructures. Various means to increase the lateral resistance of micropiles include battering and installing an oversized casing in the top portion of the piles (FHWA 2005; and Richard and Rothbauer 2004). However, it is often not possible to install micropiles in a battered position in highly urbanized areas due to existing adjacent structures or utilities. Installation of oversized casing is often restricted by limited space availability and concerns of losing lateral capacities due to closely spaced group of piles. Thus, estimation of lateral resistance of vertical micropiles can become highly important for geotechnical engineering projects in urban areas when a small to moderate amount of lateral resistances are expected from the substructures, often to withstand seismic and wind loads.

Jan 1, 2019

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"Japan’s Great Tohoku Earthquake and the immediately following tsunami of March 11, 2011 killed more than fifteen thousand people and destroyed numerous buildings and infrastructures in the northeastern part of the country.In addition to reconstruction projects in the areas where the earthquake and tsunami hit, other seismically vulnerable regions in the country have started building new and more robust facilities as well as upgrading existing coastal structures so they will be able to cope with such deadly seismic and hydraulic force. This paper will highlight two different types of aseismic and anti-tsunami levee upgrades currently under construction on the coast of Kochi Prefecture, approximately 500 miles west of Tokyo. The first type is the installation of double sheet pile walls in existing seawalls. The second type is to drive tubular piles into existing levee structures for reinforcing them. Both sheet and tubular piles are being driven by the Press-in Piling Method without removing or compromising the function of the existing structures. 1. BACKGROUNDGreat Tohoku Earthquake of March 11, 2011 caused severe damage to many structures. ASCE’s survey of damaged coastal structures conducted immediately after the disaster by Ewing, et al. (2014) categorizes failure modes of the structures in the following manner.?Overtopping without structural failure.?Overtopping with structural damage or failure.?Wave uplift forces.?Movement of structure off foundation from sliding, rotation, or overtopping.?Impact loads.?Hydrostatic pressure.?Supercritical flows.?Scour.?Erosion.?Abutments end effects.?Subsidence."

Jan 1, 2017

By William (Bill) H. Walton

"I arrived in Chicago in 1993 with Dr. Ralph Peck’s University of Illinois bulletin titled Engineering Properties of Chicago Subsoils (Bulletin 429), which he published in 1954 with William Reed. Being an outsider, I wanted to learn from Chicago geotechnical practice leaders that included Clyde Baker, Jr., John Gnaedinger, Charles Pfingsten, Dr. Safdar Gill, Robert Lukas and Dr. Jorj Osterberg, who have influenced foundation designs for the structures that make up the contemporary Chicago skyline. One of my immediate goals was to get the Illinois Structural Engineering license to be on par with the likes of Eli Cohen, Mike Tylk, Stan Korista, Bob Halverson, Joe Burns, Ron Johnson, Bill Baker, Bob Sinn, Chuck Anderson and Dave Eckmann, who have led their structural firms in the design of the skeletal core and frames of many of Chicago’s iconic buildings (and for many other buildings around the world). From my time with GEI Consultants (GEI), then on with STS Consultants (STS, and now AECOM), and now back with GEI, I have had the opportunity to analyze and design foundations and, with the help of many skilled foundations and building constructors, to verify that predicted foundation performance matches actual movement data. The theme of Chicago’s foundation design practice is to assume and verify. In 1948, Peck published the History of Building Foundations in Chicago (Bulletin 373) that was updated in 1998 by Baker, Pfingsten and Gnaedinger, who meticulously documented hundreds of Chicago’s foundations, and have shown the value of advanced analyses and testing to advance the deep foundation design practice that includes a variety of high-capacity driven and drilled deep foundations. Mehmet Uyanik, Peck and Baker have made Chicago’s subsurface into a full-scale foundation test laboratory. They confirmed soil mechanics principles like Terzaghi’s 1-D consolidation theory when early foundations bearing on sand-clay crust over soft to medium silty clays (e.g., Auditorium, Masonic Temple, Monadnock Block and Old Board of Trade buildings) took 40 to 60 years to consolidate clay 1 to 2 ft (0.3 to 0.6 m). They also confirmed proven increases in bearing pressures based on measured performance of deep foundations bearing on the glacially derived hardpan clay till and in solid dolomite that underlies Chicago."

Jan 1, 2017

By Guo Qian, Du Guangyin, Deng Yongfeng, Liu Songyu, Wang Ningping

"Metakaolin (MK) can efficiently enhance the strength and the impermeability of concretes and mortars. However, it has rarely been attempted in admixtures of cement-stabilized soils until presently. As deep mixing method is wildly used in ground improvement, the strength of cemented soils (soilcrete) and the applicability of the MK should be considered. This paper focuses on the macro-strength development of cement-stabilised silty soil mixed with MK. The result shows that the addition of MK can enhance the unconfined compressive strength of the soilcrete, which attributes to a combination of the rates of OPC hydration and the MK-CH reaction. Note that the strength of soilcrete was influenced by the properties of soil, water-to-binder mass ratio (W/B) in admixtures, which needs to be reconsidered since the binder mass composes that of cement and MK totally.INTRODUCTIONCement was used in ground modification techniques, such as the jet grouting, deep mixing method (DMM) which was put into practices in Japan and Nordic countries in the middle of the 1970s, and then spread to China, South East Asia[1]. For last decades, fly ash, slag or silica fume was mixed with cement to form the new cement base stabilizing agent in the view of economy and performance improvement. The mechanical behavior of these soil-binder admixtures (nominated as “soilcrete”), was investigated. But the soilcrete modified with the metakaolin (MK) was still not investigated much and lots of further work needs to be conducted.Some laboratory experiments of the soilcretes modified with MK have been taken[2~4]. Kolovos et al. (2013) indicates that the unconfined compressive strength has a more significant improvement when W/B equals 0.4 than that when W/B equals 1.20 concerning the water-to-binder mass ratio (W/B). Sonebi et al. (2013) investigates the mechanical behaviors of cement grouting containing MK with W/B equals 0.4, and also found the effectiveness of the addition of MK. Zhang et al. (2014) performed the studies on Lianyungang marine clay improvement showed that MK obviously enhanced the quality of cemented soils.In this paper, the strength of soilcrete modified with MK is further investigated, where the unconfined compressive strength at different curing time, the content of MK and cement (w/w) in lab conditions was discussed."

Jan 1, 2015

By Chris Leach, Lucie Spencer

This case study describes the geotechnical aspects of the basement construction for a multi-storey, residential and hotel complex located in the newly developed Elizabeth Quay precinct in Perth, Western Australia. The development included a three-level basement for car parking covering the full site area which was constructed using the top-down construction sequence. Soil conditions generally comprised 2m of fill overlying medium to dense clayey sands that in turn were generally overlying a very stiff clay stratum at approximately 13m depth. Bedrock level was generally encountered at approximately 22m to 35m below ground level. The ground water table was at a depth of approximately 1m below the existing ground surface level. A site boundary basement wall was constructed using a diaphragm wall retention system. The majority of the vertical loads from the building were transferred to the Kings Park Formation (KPF) bedrock through the use of foundation piles constructed by the CFA method. The CFA piles were installed from existing ground level, resulting in approximately 9m sacrificial concrete length from pile platform level to basement 3 (B3) level. The permanent column loads are such that a single CFA pile was not structurally adequate. To allow a full CFA foundation system to be adopted, an innovative design and construction approach was developed for these heavily loaded columns. This paper discusses the site technical details and the design and construction aspects required to meet the challenges offered by this project.

Nov 1, 2022

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

By Musbah A. Hasan, Ahmed M. Nasr, Fauzi Jarushi

Many transmission towers, high-rise buildings and bridges are supported by piles. These structures may be subjected to large lateral loads. Therefore, experimental investigations on model piles under lateral loads were conducted in uniform dry sand. Small-scale model tests were carried out considering the influence of pile length, pile diameter, sand density, roughness of pile surface and vertical load on the lateral resistance of a pile. Furthermore, the effect of pile load eccentricity (e/L) on the ultimate lateral resistance was studied. Investigations, of the influence of various parameters on the magnitude of the coefficient of subgrade reaction (nh), were also performed. It was found that the lateral load capacity of piles increases with increase in pile length, pile diameter, pile surface roughness and increase in the sand density. The results also showed that the coefficient of horizontal modulus of subgrade reaction, (nh), decreases with deflection increase. From the results, the coefficient of subgrade reaction for a smooth pile embedded in medium dense sand would decrease by (134%) when the lateral pile head deflection (yg) changes from (2% to 5%) of pile diameter.

Jan 1, 2017

By Nagarajan. D, Raja Rajan. K, Vijayakumar. T

Major bridges crossing mighty rivers must be constructed in flowing water. Constructing the sub-structure in water has been a challenging job for contractor. Special construction techniques with marine fleets to be adopted for waterfront construction. Enabling works like temporary piling platform and cofferdam used for pile and pile cap construction. Apart from this, enabling works like load out jetty to transport the materials from land to water; temporary walkway for access of workman to work location; temporary access bridge for construction vehicles movement; temporary liners for tower crane foundation; Concrete block to act as dead man anchor for barge movements were all required by the contractor for smooth functioning of site as per construction schedule. Investment in enabling works by contractor plays a significant role on profit margin of the project and of course with utmost safety. Design of enabling works for waterfront structures involves hydrological data like afflux, bathymetry survey, current force, scour depth and wave force to be taken cautiously for safe and economic design. Type of foundation and pile/well cap top level corresponding to water levels shall influence the construction scheme. Usage of geotechnical software like Wallap and Plaxis required for enabling work design to enhance the safety of the structure. Bathymetry and soil condition play a critical role in design and construction of enabling works. Water Discharge quantity in river along with water levels like low water level, high flood level, seasonal fluctuation of water levels has a great impact on design of enabling works. Establishing enabling works for waterfront construction near to an existing bridge is an additional challenge for the contractor. Along with design, constructing the enabling works in water requires special construction methodology and sequence of work. This paper shall provide insights on overview of design and construction of enabling works for waterfront construction.

Nov 1, 2022

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017

By Ramin Motamed, Farshid Ghazavi, Joseph A. W. Toth

"Post-disaster reconnaissance of areas affected by earthquakes has documented extensive damage to buildings with shallow foundations located in liquefaction-prone areas. Currently, estimation of liquefaction settlement is based on empirical correlations that evaluate settlement in the free-field environment and are based on one-dimensional consolidation. However, observations have shown that liquefaction settlement under buildings can be considerably greater. This research is based on a series of 1- g shake table experiments using a transparent soil box to reproduce liquefaction-induced building settlement. Building settlements were evaluated using a scaled model of a building foundation representing a 1-2 story building. Comprehensive parametric study was carried out to establish the effects of several parameters on free-field and building settlements such as building width and thickness of liquefiable soil layer. The experiments utilized accelerometers and pore-water pressure sensors to monitor ground accelerations and buildup of pore-water pressures in both the free-field and model building footprint. Results of these experiments are compared to available centrifuge tests and field observations and conclusions are drawn with respect to the potential scaling effects. Lastly, this paper discusses the feasibility of installing helical piles as a mitigation strategy to reduce the building settlements by presenting some of the exploratory experimental data obtained from this series of 1-g shake table tests.INTRODUCTIONThe 2010-2011 Canterbury earthquake sequence and the 2011 Great Tohoku earthquake are some of the most recent examples where large numbers of low-story structures sustained damage resulting from liquefaction-induced settlements. This damage has commonly been observed in residential and commercial areas developed over loose, unconsolidated and saturated coarse grained soils resulting from both natural and man-made deposits. Damages incurred from the 2010-2011 Canterbury earthquake sequence occurred in the largely unconsolidated fluvial environment bordering the Avon River in Christchurch (Henderson 2013). Similar damage was also incurred during the 2011 Great Tohoku earthquake where liquefaction of soils occurred in both young alluvial deposits and fill materials (Ashford et al. 2011). Figure 1 presents typical modes of failure to structures resulting from the effects of liquefaction. Current practices in evaluation of liquefaction settlement rely on empirical correlations (Tokimatsu et al. 1987; Ishihara et al. 1992) developed for liquefiable soils in the freefield environment (Dashti et al. 2010a). However, recent observations of the performance of foundations suggest that settlement of rigid shallow foundations in liquefiable soils are commonly greater than those predicted in the free-field. Therefore, new correlations should be developed to better predict the degree of settlement of shallow foundations in liquefiable soils. Current research is beginning to focus on the mechanisms of settlement during liquefaction in regards to confining stress, pore-water pressure and shear stress induced from foundations (Dashti et al. 2010b)."

Jan 1, 2016

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By James F. Davis, Matthew A. Conte, Robert F. Tonning

This is a paper demonstrating the steps taken to combine multiple types of piles for a single site to maximize the benefits and characteristics of each method. We intend to discuss the use of grouted displacement piles in lieu of traditional pile types that were specified on an individual project. We will show how implementing this alternate pile type can both supplement and replace the originally specified pile to increase efficiency and lower costs. We will demonstrate a reduction in spoils, vibration, crew hours, and equipment size while employing methods to overcome unforeseen ground conditions.

By Kazuyoshi Kamimura, Masaya Kawata

"It has been 30 years since the cement deep mixing (CDM) method developed in Japan. CDM method has been applied to many structures. While various technical improvements have been implemented in the meantime, the single-axial and double-axial technologies used at the time of its initial development are still prevalent.In response to the recent trend of reducing construction costs, we developed a triple-axial CDM method called the “Lemni 2/3 Method.” This method uses two lemniscate motions caused by newly developed auxiliary stirring devices and employs a double-axial injection method in which the cement slurry injection takes place only from the outer two axes. In this way, it is possible to create a stabilized body around the three axes. Moreover, this method does not require substantial equipment investment as conventional construction machine and facilities can be used without modification and large volume work is possible.With these technologies, this method can achieve a substantial reduction in the construction period and cost, while ensuring the same level of improvement quality as conventional methods. As a result, this method is being applied to ground improvement work in a variety of places.Lemni 2/3 Method was first put to practical use in 2004. Since then, the method has been used for ten projects. In this paper, we show some application examples of this method.OUTLINE OF TRIPLE-AXIAL CDM METHOD (LEMNI 2/3 METHOD)In the newly developed CDM method (Lemni 2/3 Method), work efficiency is improved by employing triple-axial stirring blades instead of the conventional single- or double-axial type. Existing conventional construction facilities for double-axial type can be used with only minor equipment additions, because the cement slurry injection takes place only from the outer two axes.Construction Machine and Construction MethodThe combination of major construction machines of the Lemni 2/3 Method differs little from the standard specifications of the double-axial type as shown in Fig. 1. Existing work control equipment can be used without modification, which is further evidence of the simplicity, convenience, and economy of the new method. The Fig. 2 photo shows a full view of the construction machine, and the Fig. 3 photo shows the stirring blades and the auxiliary stirring devices. The work procedure for the Lemni 2/3 Method is shown in Fig. 4."

Jan 1, 2015

By Nick O’Riordan, Kaitlyn L. Fleming, Michael Riemer, Youssef M. A. Hashash, Stephen McLandrich, Mohamad Jammoul, Pierre Gouvin, Andrew Yeskoo

"To accommodate urbanization, cities are developing more underground space as a means to house public transportation systems and other entities. Underground developments often require construction of deep excavations in an environment dense with infrastructure. The success of such a project is related to the amount of impact imposed on adjacent structures and economic activity; impact should be limited to insignificant amounts in order to mitigate damage and disruption. Thus, large-scale urban construction projects require extensive monitoring of ground movements and installed support performance to facilitate informed decisions for adjustment of construction activities and support design when necessary.In downtown San Francisco, a unique large-scale excavation in saturated soft soils was constructed for the Transbay Transit Center (TTC). Construction of the excavation began in April 2012 and was completed almost two years later in February 2014. To monitor ground and structure response to construction, the project team used an extensive instrumentation network that included automatic inclinometers, piezometers, strain gages and total stations paired with survey markers. Innovative imaging techniques developed a record of construction in order to relate measured deformations to construction activity.Transbay Transit CenterThe Transbay Transit Center (TTC) is being constructed as a modern day transportation hub in downtown San Francisco to replace the former Transbay Terminal. The project is located in the South of Market area, less than half a mile from the San Francisco Bay. The final center will connect eight counties in the Bay Area through 11 different transportation systems, some of which will be housed in the TTC including Caltrain, Golden Gate Transit and California High Speed Rail. The aboveground structure will consist of two levels for retail and a third level with a bus terminal beneath a rooftop garden. There will be two subgrade levels to serve as a lower concourse and the train platforms. This structure required construction of a deep excavation closely surrounded by buildings and roads in an area thriving with economic activity."

Jan 1, 2015

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By I. D. McPherson, Dominic P. Mahoney

The Metro Sports Facility is currently under development in Christchurch, New Zealand and is a key Anchor Project in the city’s post-earth quake recovery. When completed it will be largest indoor sports and swimming pool complex in New Zealand, with a building footprint in the order of 22,000m2. The site is underlain by poor performing soils comprising interbedded layers of soft compressible silts and loose liquefiable sands to over 20m depth. The site is typical for Christchurch with a shallow groundwater table and artesian conditions. The site performed poorly during the 2010-2011 Canterbury Earthquake Sequence with extensive liquefaction, and associated ground damage. To provide a resilient and economical foundation system for this key development project, deep ground improvement comprising of a uniform grid of some 7,200 stone columns in conjunction with robust shallow foundations has been adopted. This paper discusses the geotechnical site constraints, and ground performance under earthquake loading and describes the various options considered for the development. The foundation option selected, the design considerations of the adopted stone column ground improvement, and foundation solution are described in detail, as well as, construction observations. The paper aims to provide insight into an urban large-scale ground improvement project for the engineering practitioner.

Nov 1, 2022

By David W. Martel, Tom George

"As part of the regional water authority review and upgrade of local dams a 35m x 5m x 3m wet soil mixed block was required for stabilisation of a dam wall toe in remote Victoria, Australia. Remote access, extremely poor roads and high mobilisation costs made more traditional CSM and deep mixing methods cost prohibitive. The dam required a redesign to raise the wall by 2.0m to increase water storage. Additionally, the dam required additional stabilisation to reduce the risk of liquefaction during an earthquake event. Soil testing indicated loose, cohesionless, high permeability soils to a depth of 3.0 to 3.5m across the toe of the wall. This resulted in high dam seepage through the toe of dam wall potentially causing the factor of safety during a seismic event to decrease to a dangerous level. A number of laboratory trials were completed to determine the mix ratio of cement required to improve the strength of the saturated, liquefiable soil.Wagstaff Piling was responsible for achieving the required soil/cement strength and mix depth on site. As the ground conditions were too soft for conventional soil mixing equipment, an excavator mounted Mitsui road header was modified to fit a 20 tonne excavator. A purpose built remote batching plant was set up on more stable ground approximately 200m from the wall and utilised for preparation of cement and water slurry for supply to the machine. As the ground was too soft to support the excavator, the progressively improved ground was used as the working platform. Both wet grab sampling and in situ testing was undertaken to determine the UCS of the improved soil. These results indicated several variations in the results due to size effects.1 INTRODUCTIONA small town in remote Victoria relies totally on its water supply from a small dam. The dam wall required stabilisation works by ground improvement as studies completed on the dam classified it as a high risk of failure under an earthquake event. In addition, the earth fill dam had high levels of seepage and poor control measures, requiring the dam to be upgraded to comply with all regulations.The relevant water authority engaged a contractor under a design and construct contract to complete the works. Wagstaff Piling was engaged as the Subcontractor to provide design and construction advice including the contract for the ground improvement works. Initial discussions involved CSM walls, cut-off walls and mass soil mixing solutions. However, due to the access restrictions for piling equipment, mass soiling mixing was the chosen method of ground improvement."

Jan 1, 2015