Search Documents

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1997

By R. Heath Forbes

The route of a new, 4-mile long, electrical transmission line passed through residential neighborhoods and commercial areas of a small town in the South Carolina Coastal Plain. The new line consisted of 54 new poles and a one-mile underground section. Most of the new poles were constructed within 50 ft of existing structures, and in some cases, within 8 ft to 20 ft. A widely-space subsurface exploration consisting of 20 cone penetration test soundings indicated the subsurface conditions along the alignment generally consisted of saturated, loose to medium dense, fine slightly silty to silty sand. The pole foundations consisted of 20 to 30 ft long, prefabricated ?caissons? (essentially an open-end pipe pile with a prefabricated connection system at the top) with diameters of 28 to 56 inches. The steel caissons were installed with vibratory pile hammers. To help prevent damage and defend against possible allegations from nearby property owners, vibration and settlement monitoring was performed during all foundation installation activities. Limited structural condition assessments were also performed before and after foundation installation. For 53 of the 54 foundations, the ground vibrations recorded at distances coincident with the nearest structure locations ranged from 0.05 inches per second to 1.46 inches per second. With consideration of the dominant frequency, the majority of these values were below the commonly used USBM vibration limits. For a foundation installation that was only 8 ft from the nearest structure, a peak particle velocity of 3.06 inches per second was recorded, which exceeded the USBM limits. For all cases, the measured ground surface settlement was negligible (i.e., less than ¾ inch). Several spurious claims alleging vibration-induced damage were made, but the monitoring program provided an adequate defense. One claim involving artwork that fell to the floor during foundation installation at a distance of 8 ft from the house was deemed legitimate.

Jan 1, 2011

By Aminul Islam, Vinay M. Kumar

"About 100 Hectares of land reclamation over the very soft to soft marine clay at Uran Creek in Maharashtra is planned. The depth of marine clay varies from 10m to 24m as observed from the geotechnical investigation. The marine clay was treated with Pre-fabricated Vertical Drains (PVD’s) installed from the elevation of +5.5mCD (chart Datum) and preload/placement of surcharge. A Settlement of soft soil mud under the reclamation was monitored using magnetic extensometer (M) and ground settlement maker (S2). These instruments are installed after constructing working platform at around +5.5m CD. Based on the field instrumentation data, the consolidation parameters were adjusted to match the theoretical and actual settlement plot. The author called this approach as “Back analysis method”. The objective of this paper is to present a case study of instrumented preloading treatment for a thick marine clay deposit. The degree of consolidation in clay strata was determined from magnetic extensometer and ground settlement marker data. Authors also determined degree of consolidation as Asaoka method, Hyperbolic method and Back analysis method and compared the results.INTRODUCTIONExpansion of Container terminal with port buildings, rail container depot, roads and utility buildings at Jawaharlal Nehru Port Trust (JNPT) is planned over a reclaimed land of 100 hectares. Uran creek predominately consists of the estuarine deposit of very soft to soft marine clay. They are characterized by low shear strength, very low bearing capacity and exhibit large settlement when subjected to loading. The additional load causes the significant magnitude of consolidation settlement over a considerable period of time. Thus for development projects on top of soft soil, the postconstruction settlement would be of primary concern.To accelerate the consolidation pre-fabricated vertical drains (PVD) were used. Pre-loading procedure was adopted to minimize the post construction total and differential settlements. PVD’s were installed at 1.0m and 1.2m c/c triangular pattern. Locally available borrow material is used as a reclamation material. The reclamation material has been placed over the existing sea bed level by land based method/end tipping method and created the working platform. The level of working platform is decided based on the tide data and it has been selected such that work should be affected during highest high water level. The PVD has been installed from the working platform and subsequently all the field instruments have been installed from the same level. Five different types of field instruments are installed to monitor ground improvement works."

Jan 1, 2017

By Camilla Favaretti, Benjamin Turner, Anne Lemnitzer

Pile foundations are extensively used in the construction of various types of superstructures, including tall buildings, bridges, freeways and offshore structures. A fully constrained tip embedment such as a rock-socket offers an attractive solution for achieving significant tip resistance and improving the load-carrying capability of the foundation element. In profiles with very soft surficial soil, rock-socketing often provides the only reliable source of axial and lateral resistance. In preparation of a large-scale testing program on rock-socketed piles at UC Irvine (UCI) geared towards studying the magnitude of shear amplification at the rock-soil boundary of pile foundations, a pre-test model-scale experiment was executed in the UCI Structural Laboratory. The objective of the model-scale experiment was to iterate and validate the test setup, study the influence of important boundary conditions, assess instrumentation techniques and sensor placement, and to gain preliminary insight into the small-scale specimen non- linearity. In addition, this model-scale study provides ample opportunity to compare lateral performance parameters with analytically predicted lateral load behavior using traditional soil resistance functions and limit state analyses and explore new techniques for the derivation of soil resistance functions. The pile specimen had a pile diameter (D) of 10 inches and a total pile length of 125 inches. The pile was embedded in a 40 inch simulated rock socket overlain by 52 inch of medium dense sand (DR~50%). The pile extended 32 inches above the soil surface, where cyclic lateral loading was applied. The pile was installed in a laminar metal frame box with inside dimensions of 39 inches in width (W), 73 inches in length (L) and 86.1 inches in height (H) as shown in Figure 1. During testing, the box was restrained using a rigid bracing system consisting of concrete reaction blocks, wooden braces and steel girders.

Jan 1, 2018

By G. T. Hong

A numerical model for use in design is developed to predict the stresses and axial and bending displacements in a drilled pier in expansive soils. The prediction is based on the horizontal swelling pressures and uplift forces which act on the side of the drilled pier. The exponential suction envelope with the depth within the moisture active zone is estimated based upon the equilibrium suction, moisture diffusion coefficients obtained from laboratory tests, and minimum suction at the ground surface of the site based on field conditions. The volume change of soil is based on suction variations, soil properties, overburden pressures, crack influences, and the relationship between moisture contents and suctions. Considering the movement active and anchor zones on a soil-pile system in expansive soils, horizontal swelling pressures are formulated using the shear strength of an unsaturated soil and the Mohr?s circle and failure envelope. The movement active zone has two sub-zones in which horizontal swelling pressures are attributed to passive earth pressure failure and suction change in the upper and lower sub-zones, respectively. Horizontal swelling pressures which occur in the anchor zone are assumed to be in the at rest condition. The shear stress generated on the vertical surface of a drilled pier is supported by the nonlinear curves of load transfer versus relative displacement. The axial behavior and lateral bending of the pier in expansive soils are simulated using a beam column approach. The computed axial and bending displacements and stresses are used to provide structural design of the pier. Figures of computed results for typical cases are presented.

Jan 1, 2007

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By George G. Goble

In the middle of the nineteenth century, the dynamic formula appeared as a description of pile penetration during impact driving. The simplicity of use of the formula combined with the power of the energy concepts behind the formula caused it to be quickly accepted and integrated into practice. Dynamic formula had been in use for 100 years when the Wave Equation computer programs first appeared. With that long experience it is not surprising that the formula continued to be used and were only slowly abandoned. The Wave Equation offers many advantages over the various formula but it does not offer a clear sense of physical understanding of pile driving that is available with the formula. Large amounts of numbers are generated but often it is difficult or impossible to gain a physical understanding of the results or a feeling for the importance of the various parameters. The question that the Wave Equation user has is, "What will happen if I use a larger drive cap (or change any other item of equipment)?" In this paper, I will attempt to explain pile driving using elementary wave propagation theory. However, the presentation will not depend on any higher mathematics. With the use of wave mechanics, it is possible to explain driving characteristics that cannot be handled with the energy formula.

Jan 1, 1995

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By Ryan Higbie, King Chin, Matthew Anderson, Mike Huggins, Rian Johnson, Dave Sinsheimer

"The Permanent Canal Closures and Pumps (PCCP) project is the capstone piece of New Orleans’ extensive hurricane risk-reduction system constructed following Hurricane Katrina. The project consists of three discrete pump stations and flood gates on the shore of Lake Pontchartrain which provide a storm surge barrier and pump rainwater from the City of New Orleans’ primary drainage canals. The depth of the pump station structures ranged between 39 and 45 feet below sea-level. USACE developed the PCCP project for design-build delivery; granting the project team latitude to develop innovative, cost effective solutions for the project. The use of OPEN CELLTM cofferdams to construct the pump station structures was one such innovation. OPEN CELL structures utilize the strength of the retained soil to anchor cellular sheet pile face arcs; allowing a free-field of construction within the cofferdam. This cofferdam design did not require ground improvement or dewatering around the perimeter of the cofferdam. The free-field cofferdams streamlined construction and large equipment installation within the structures with no encumbrance from internal bracing. Meticulous force-based design, soil-structure numerical modeling, and physical testing were all techniques used to present and gain USACE acceptance of the design on this vital element of the work.PROJECT DESCRIPTIONThe Permanent Canal Closures and Pumps (PCCP) project is the capstone piece of the City of New Orleans’ extensive hurricane risk-reductions system constructed following Hurricane Katrina in 2005. The project encompasses three separate pump stations and floodgate structures located at the mouths of three outfall canals (17th Street, Orleans, and London) on the south shore of Lake Pontchartrain. These three canals, running from the south to north, act as the primary conduits for discharging water from the New Orleans area. Prior to Hurricane Katrina, these canals were operated with pump stations two to three miles upstream of the mouths at Lake Pontchartrain. This left long stretches of levee on each side of the canals exposed to storm surges entering from the lake. Three levee failures occurred along these canals during Katrina; two at London Canal and one at 17th Street Canal. The failures resulted in major flooding of the surrounding neighborhoods, significant damages, and loss of life.Following initial canal levee repairs after Hurricane Katrina, USACE, in partnership with the Louisiana Coastal Protection and Restoration Authority (CPRA), took action to move the line of flood protection to the mouths of these three canals at the edge of the lake. By cutting off the storm surges from Lake Pontchartrain at the entrance to the canal, over ten miles of canal levee would no longer be exposed to storm surge water elevations, significantly decreasing the risk of failure."

Jan 1, 2017

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By Gordon Demetrick

3900 Yonge St. was not a typical site on which to build a condominium apartment. A steep hill covered the majority of the site. In order to use as much of this site as possible, the rear of the building was to have nine stores cut into the face of the hill. A permanent shoring system was required as the building structure was not designed to provide sufficient stabilizing elements to support the total earth pressure. The total excavation depth required was 36 m (120'-0") with the upper 12 m (40'-0") to be backsloped. The vertical face of soil to be supported was 24 m (80'-0'). The shoring system originally designed by the Structural Engineer was to support this face by installing soldier piles and inclined earth anchors. During bid preparation it became evident to us that the system as designed would be difficult and expensive to install due to wet soil conditions. An innovative design was required to overcome these problems. Anchor Shoring hired John Stephenson Consultants Ltd. to aid them in accomplishing this goal. After extensive investigation together with The Trow Group, a unique design was proposed which provided a practical solution to the shoring problem.

Jan 1, 1987

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Nuno Cruz

"The concrete overbreak estimation for bored piles provides the quantification of the shaft’s expansion beyond its theoretical volume. There are stability analysis methods that can be employed before and after concrete pour but as for the moment of decision, during pile cast, the most common method still consists in measuring the rising of the concrete level in order to compare its poured volume with the theoretical pile section volume. This is a determinant parameter to monitor, not only because it assesses the bored shaft stability but also because it represents a direct cost. When analyzing the estimation methods commonly applied on-site it becomes evident that these are often affected by human errors that lead to misleading results. The objective of this paper is to identify those errors and discuss a subject which is usually overlooked. As a general conclusion, it was ascertained that most errors derive from inaccurate volumetric data, working procedures and gauging equipment. By acknowledging these widespread practices deep foundations contractors will be in a better position to make informed decisions on how to correct and improve bored pile stability.GENERALBackgroundWhen executing bored piles, the estimation of its concrete overbreak allows a swift appraisal of the excavation stability during the drilling process. This is simply obtained from the proportion of the poured volume of concrete over the drilled shaft theoretical volume, as shown in equation [1].Where CO = concrete overbreak percentage, Vc = volume of poured concrete, Vr = pile’s theoretical volume. This calculation not only provides a general idea of the shaft’s expansion from its theoretical volume, but also the outline of the excavated column’s geometry. For the latter, the outline will be as accurate as the number of measurements taken for each partial known volume of poured concrete. This means that for each load placed inside the excavation there is a corresponding rising of the concrete level. The profile of the definite pile is then plotted (see Fig. 1) and allows inferring about how stable remained the shaft walls up to the moment of casting.The technological developments in this area have provided other methods for determining pile stability before and after pile cast, such as ultrasonic echo sensing, cross-hole sonic logging or thermal integrity profiling systems. Notwithstanding, concrete overbreak assessment remains as common practice and confers the advantage of providing stability information during the process of pile casting."

Jan 1, 2017

By Giovanni A. Bonita

The new Embassy of the Peoples Republic of China in the United States (Chinese Embassy) is located in the Embassy Row portion of Northwest Washington DC. The 475,000 ft2 (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. The structure approaches the property line on all sides, and is immediately adjacent to several foreign embassies and a secure U.S. Federal Building. A vertical soil nail wall was used as the primary support of excavation (SOE) system for the project. The soil nail wall was irregularly shaped, benched in areas, and reached total heights up to 98 feet (29.9 m). The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Tight excavation requirements were defined for the project due to the location of the building relative to the property line, requiring fairly precise wall positions and shotcrete tolerances. Design challenges included soft soil conditions, inside wall corners, underground utilities, and seismic impacts from blasting. The paper will focus on the design, construction, and performance of the soil nail SOE system, as well as touch on the logistical and political factors that influenced the design. The paper also notes the Value Engineering and communication approaches that were generated during construction. These efforts resulted in a significant improvement in the quality control and quality assurance exhibited on site, expedited the schedule, and led to significant cost savings to the contractors, engineer, and owner.

Jan 1, 2006

By W. G. K. Fleming

The general history of piling is traced up to the present time with regard to the evolution of methods and materials. The processes have been strongly influenced by developments in basic equipment and industrial change. It is noticeable that in the twentieth century more progress has taken place than in the many previous centuries. It has been strongly influenced by the general development of Soil Mechanics. Test loading is probably the most effective way to assess the success of designs and many empirical relationships have been challenged through it. As we approach a new century it appears that it will be an age of rapid equipment development, with much enhancement of understanding of what has been done. Processes of automatic construction and testing will becoming commonplace. These changes will narrow the limits of conventional scatter that have come to be accepted and to a large extent will be driven by political efforts to curtail energy consumption, to raise standards of quality and reliability, and to conserve the environment. 1. Ancient history. Piling is an ancient art. Its first mention in history is from Herodotus, the first person to commit an account of his times to the written word in the years 557 to 479 BC. He evidently had a strong interest in engineering matters because he wrote of building, brick making, reinforced brickwork, river training, canal building, bridge construction, tunnelling and its acoustic detection and piling. The piling reference comes from Book 5 at paragraph 16.

Jan 1, 1999