Search Documents

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

By A. Tejchman

On the site of building of a new flyover founded on piles the comprehensive "in situ" investigations were carried out. The subsoil conditions under each of 15 supports were very differentiated. Using of the static sounding results a new method for evaluation of bearing capacity and settlement of piles was proposed. The method is based on a special construction of the curve of load-settlement relationship. The verification of this method was made on the basis of loading of piles.

Jan 1, 2010

By Douglas L. Scaggs

Driving piles in under water applications has become more common place over the past twenty years. Where only a water depth reachable with a follower or dewatered cofferdam was the rule in the past, newer technologies developed for the offshore oil and gas industry have made depths of even several thousand feet possible offering new possibilities in foundation design and installation. With the new technology, engineers can now more efficiently design structures by placing foundations optimally thereby reducing weight and cost of the overall structure.

Jan 1, 2013

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Edward C. Clukey

"Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed.During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor’s QA/QC program should be increased to achieve a foundation system with the required level of reliability.Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially “at-risk”. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.IntroductionThe foundation support system for the process train at a major LNG facility comprises more than 6,000, 23-m long DMM elements. The general subsurface stratigraphy at the project site comprises (from the ground surface): (i) up to 8 m of fill sand initially placed underwater building to a stable construction platform; (ii) up to 12 m of soft organic clay (Unit II clay); and (iii) clayey sand and sand layers becoming progressively denser with depth (Unit III sands). Each DMM element comprised two secant 1.5-m diameter DMM columns. DMM elements were typically arranged as cells enclosing one, two, or three DMM elements."

Jan 1, 2017

By Moonkyung Chung

Static pile load tests were performed in order to evaluate bearing capacities and mechanical behaviors of three different pile types: (1) steel-concrete composite drilled shaft with rebar reinforcements inside the concrete, (2) steel-concrete composite drilled shaft without rebar, and (3) conventional drilled shaft (reinforcement concrete pile). The material elastic moduli obtained from pile load tests of steel-concrete composite drilled shafts with and without rebar reinforcement were found out to be similar. On the other hand, the elastic modulus of steel-concrete composite drilled shafts is almost twice as high as that of the conventional drilled shaft. The ultimate strengths of the steel-concrete composite drilled shaft with rebar, the steel-concrete composite drilled shaft without rebar, and the conventional drilled shaft were 9,810, 7,848, and 4,414kN, respectively. The results of these load tests reveal that the ultimate strengths of the steel-concrete composite drilled shaft with reinforcement and that without reinforcement are 2.22 times and 1.78 times greater that that of the drilled shaft. The structural failures of the steel-concrete composite drilled shafts occurred either at the boundary between tip of steel casing and rock-socketed concrete.

Jan 1, 2010

By Wei Tu

A grade separation was required to allow uninterrupted traffic crossing for a busy rail spur and a county road. The grade separation was achieved by creating a 30-foot (9-meter) high embankment that incorporates two multiplate tunnels and allows the passage of a rail spur and an existing county road. The site is located in an abandoned meander channel in the floodplain of the Mississippi River, near Osceola, Arkansas, and is underlain by more than 40 feet (12 meters) of soft clay and interlayered clays, sands and silts. Without soil improvement, the post-construction settlement would exceed 3 feet, slowly crushing the proposed tunnel structure and cutting off the railroad. Preloading, combined with vertical drains, was used to accelerate the consolidation of the underlying soil layers and to reduce the post-construction settlement under working loads. Six settlement plates were installed to monitor the progress of consolidation under surcharge load. The Asaoka observational method and the hyperbolic fitting method were used to analyze the measured settlement data to predict the end of primary settlement. The in-situ consolidation coefficient, ch, was back calculated from the measured settlement data. The stress release caused by the removal of the preloading surcharge load and the tunnel installation was determined using a Plaxis 3-D finite element model. The measured and predicted settlement using Hansbo's analytical solution demonstrated reasonable agreement. Early removal of the surcharge and construction of the tunnel prior to reaching the end of primary settlement was accomplished by analyzing the post-excavation stress reduction achieved via tunnel construction.

Jan 1, 2009

By Andrew Stauble

This project included the replacement of the Long Island Railroad (LIRR) Atlantic 6 Bridge in New York City, which services rail traffic and spans the Van Wyck Expressway and frontage roads. The bridge re- placement was part of an overall project to widen the Van Wyck Expressway between Kew Gardens and John F. Kennedy Airport, which serves as the major route for vehicular traffic between the airport and the city. The railroad bridge crosses the expressway and frontage roads in a significantly congested area, and it services an average of approximately 140,000 commuters per day through- out the boroughs of Manhattan, Brooklyn and Queens. The existing bridge superstructure and foundations were to be demolished and new structures and foundations were proposed to be constructed at the bridge's east and west abutments and center pier. The new bridge would be supported on driven H-piles. To facilitate the construction of the new bridge's abutments and center pier, a support of excavation design was required to support the grade around the existing structures. The design shown on the contract drawings included a driven soldier pile and lagging wall with multiple rows of drilled tiebacks at the abutments to laterally support excavation heights of up to 36 ft (11 m). The existing abutments are located directly adja- cent to frontage roads that have an extremely high vehicle traffic volume,

Aug 1, 2023

By Thomas M. Caruso

Construction of a new ship dock at a major Philadelphia area refinery required geotechnical design and field consultation. The new dock, which consists of a system of mooring dolphins and platforms, will be capable of docking the Stena V-MAX Oil Tanker (V-MAX). The 1100 ft long V-MAX is currently the largest tanker to travel the Delaware River and will induce significant lateral loads on the new ship dock. Lateral loads induced on the dock will be resisted by over 200 pipe piles installed on a batter. The piles used for support of the dock included 20 and 30 in. diameter reinforced, concrete filled pipe piles. Complete construction of each pile included driving of the pile to the design ultimate capacity, flushing the pipe pile casing clean of overburden materials followed by drilling rock sockets into the underlying Wissahickon Formation. Variations in depth to bedrock, rock quality and degree of weathering and presence of very hard quartzite lenses created a complex geologic environment that presented challenges for the pile/rock socket design and installation. The design of the pile system, installation methods, QA/QC and testing (Pile Dynamic Analysis), as well as the challenges that were encountered through the duration of the project are presented and discussed.

Jan 1, 2008

By Michael G. Batten, Brian D. Keaney

]The Virginia Department of Transportation (VDOT) and the harbors on the James River routinely use precast concrete piles founded in the Yorktown formation to support bridges and other coastal structures. However, axial pile resistances for large diameter piles in this area have been historically overestimated on past projects. This may be due to a common assumption that very large unit end bearing resistance will be developed for a large diameter displacement pile that is driven a significant depth. This assumption is integrated in the Nordlund (1963; 1979) method which is commonly used to estimate axial pile resistance for bridge foundations. A static and dynamic pile load testing program was implemented as part of the Hampton Roads Bridge and Tunnel Expansion project in Norfolk, VA in the James River. A primary objective of this program was to calibrate an axial resistance calculation method against the measured load test results. A method developed by Eslami and Fellenius (1997) that uses CPTu data directly was effective at calibrating to the measured load test results, and allowed for clearer interpretation of the unit resistance values than indirect, semi-empirical methods that require interpretation of soil friction angle and undrained shear strength.

Sep 8, 2021

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Daniel W. Mageau, Larry W. Applegate, Aaron K. McCain

"An innovative method of ground freezing was successfully tested to create a “dry” excavation condition for a new building foundation at a site in downtown, Miami, Florida. The subsurface conditions in Miami generally consist of very porous, weak limestone and sand with groundwater near the surface. Water flow through these materials can be very high. Dewatering is extremely restricted in Miami so deep below-grade structures are rare and expensive. A new, innovative method to allow deep excavations in dry conditions without dewatering involves the creation of a thick, temporary, frozen soil plug below the planned excavation depth across the entire site to cut off vertical groundwater flow during construction. Frozen soil is impermeable and very strong and has long been used for temporary structural and water-tight shored walls. Using the same proven principals, frozen soil plugs are very effective at cutting off water from the bottom of the excavation as well as resisting upward buoyant forces. This new freezing method can be used for fairly deep excavations in new building construction supported on deep foundations. The building piles act as temporary anchors for the frozen plug to resist very high upward buoyant pressures until the permanent structural slab is completed.IntroductionUnlike other Cities, below grade basements are rare in Miami. The few basement foundations constructed have utilized a cumbersome and expensive method of excavation and shoring involving underwater excavation, tremie slabs, and commercial divers. The key issue for underground construction in this area of the country is the vertical flow of groundwater through the base of the excavation. To deal with this issue in the past, the contractor first installed all of the building piles and the perimeter shoring walls. Then, interior sheet pile walls are installed to create small manageable excavation pits. Each pit is then excavated through standing water “in-the-blind” and around the buildings support piles. The final excavation, interior struts, and inspection is performed by commercial divers. Finally a thick foundation tremie slab is poured under water. This method could be successful but proved to be time consuming and expensive. In addition, some building piles were occasionally damaged during the under-water construction process."

Jan 1, 2015

By Kenneth M. Berrry

A unique situation has developed at an abandoned coal mine in St. Clair County, Illinois. Subsidence features have been observed at the ground surface over the mine including settlement of a pair of bridges for Illinois Route 158. The Illinois Department of Transportation (IDOT) is currently replacing the two bridges. Foundation treatment for the two new bridges included backfilling the mine void. The light rail system for St Louis (MetroLink) is also constructing a bridge over the same abandoned coal mine less than 1000 ft from the Route 158 bridges. The new MetroLink bridge is being constructed using piles which extend through the coal mine and overlying bedrock in order to transfer the loads to below the mine floor. The differing foundation types for the IDOT and MetroLink bridges were due to geometry and economic factors involved with the individual structures.

Jan 1, 2001

Volume 1 pages 665-671 Title should read as Dynamic pile testing of H-piles at HDB sites J.Wei, Y. S. Heng, C. S. Lok, M. K.Chong Housing and Development Board, Singapore 'tons' should read as 'tonnes' Para 3.2 fourth equation (page 667) [TC = t2 v.dt t = 0 should read as TC = t2 v.dt - s t = 0]

Jan 1, 1994

By Matthew Janes

The installation of piles and casings is becoming increasingly difficult as restrictions on vibration become common in major urban areas. The use of high frequency, resonant excitation of a pile or casing permits ease of installation of sections to great depths with near imperceptible vibrations as close as 1 pile diameter. The new Resonant Driver is able to excite a pile at its resonant frequency (up to 150 Hz or 9000 VPM) to produce elevated levels of acceleration, force and displacement in the pile. The combination of extremely high acceleration and controlled levels of displacement allow the pile to slice through varied soil with almost no vibration translated into the ground. In direct comparisons between conventional vibrators and impact hammers the Resonant Driver produces less than 1/50th the vibration. The Resonant Driver results in ground vibration of between 1/20 and 1/40 of common limit levels (1 cm/s or 0.5 in/sec) as close as 1 pile diameter. At a distance of 5 m (16 ft) from the pile or casing vibration levels approach imperceptible levels. The Resonant Driver uses a proprietary algorithm to tune the drive vibration to the changing natural frequency of the pile as it is driven into the ground. By maintaining resonance the energy in the pile is built up like in a flywheel on an engine or a child on a swing. This build up of energy aids in driving and significantly reduces waste. Recent experience using the Resonant Driver is proving the technology can drive a variety of steel pile and casing sections through varied soils. Continued use of the Resonant Driver will create a data base of various pile and casing sections, soil types and achieved capacities.

Jan 1, 2008

By Hector Simchas

"1. BENTONITE: THE CRUCIAL CONSTITUENT OF SLURRYSuspensions of bentonite and water are used in a variety of applications in underground engineering. For the construction of underground elements like slurry walls or piles, bentonite slurries offer support to the excavation of loose soils and counter pressure against hydrostatic pressure of ground water, especially where soil permeability is high. In addition, for the construction of tunnels by the slurry-shield method or when hydromills are used for excavation, bentonite suspensions transfer the loosened soil to the surface. In applications like pipe jacking and microtunneling, or where high revolution drilling is required, bentonite also provides lubrication and cooling.To fulfill these functions, the properties of a bentonite slurry need to remain stable, or at least predictable, during the course of construction. Unfortunately, when a suspension mixes with earth, ground water and/or impurities, its properties may be compromised resulting to reduced performance, which would in turn lead to increased construction costs and the risk of the excavation collapsing. Our experience in the lab and onsite is presented herewith.2. MOST USUAL FACTORS OF PERFORMANCE FAILUREWater and soil quality are important factors defining the behavior of suspensions. In an extensive program of measurements in our technical laboratory, the effect of frequently encountered harmful substances on bentonite suspensions has been examined and the results are summarised in Table 1.Some tests show that the conductivity of water has a direct relationship with Marsh Viscosity. For example, we have seen that if the quantity of bentonite required to achieve a 40s Marsh Time ranges between 50-52 kg/m3 at water conductivity below 100 µS/cm; when conductivity is increased to 1,400 µS/cm, we need 65-68 kg/m3 in order to achieve the same property."

Jan 1, 2015

By Andrew Cushing

This paper presents the design and construction of the foundation for a major high-rise real estate development on the west side of Manhattan. Arup was retained by Underpinning and Foundation Skanska to design a secant pile wall as excavation support for a proposed two-level basement of a new 23-story residential building located at 100 11th Avenue and West 19th Street. The secant pile wall will also act as the permanent basement retaining wall for the new building. The site is bounded on two sides by existing structures and is underlain by a thick deposit of very soft organic silt and clay. Therefore, the potential for ground movements and their impact on an adjacent structure bearing on shallow footings were of the utmost concern. This paper addresses the design and construction considerations associated with this secant wall, as well as installation details. Measured wall movements are also used to assess the validity of the pre-construction soil strength and stiffness design parameters.

Jan 1, 2008

By Ahmed Elmekati, Frederick C. Rhyner, Steven R. Lowe

"The current phase of the Pacific Park development (formerly, Atlantic Yards) in Brooklyn involves constructing buildings on a platform over an existing LIRR rail yard. To preserve the maximum amount of space in the already congested yard and protect the yard which remains in service during construction, high capacity foundations are being designed well above previous capacities in the area. In addition to spread footings and small mats, various diameters of drilled piles are being used at design capacities ranging up to 600 tons. The piles are generally grouted at low pressure, up to about 50 psi. Load tests for various drilled elements, including piles, tiedowns and soil anchors, have confirmed allowable side resistance (bond) stresses in dense sand ranging from 20 to 30 psi. Testing with different rigs and operators has shown that down-the-hole hammers are feasible, but the installation techniques, types of equipment and size of the pile make a significant difference. The results show that more cost-effective foundations are possible when ample testing confirms expectations.I INTRODUCTIONThe Long Island Rail Road has operated a mainline on Atlantic Avenue since the 1800s, with a terminal at the intersection of Atlantic and Flatbush Avenues. In the early 1900s, the mainline was reconstructed in a cut and cover tunnel section. The LIRR’s Atlantic Yard was constructed circa 1908 to service the terminal. It was depressed about 25 feet below street grade to coincide with the LIRR’s mainline tunnel under Atlantic Avenue. Record drawings indicate that the gravity retaining walls lining the perimeter of the yard and other ancillary structures had been designed for an allowable bearing pressure of five tons per square foot (tsf). Perhaps by coincidence, the mat foundation for the tower of the Williamsburg Savings Bank was also designed for five tsf in 1929.Figure 1 shows a typical geologic section through the site. The geology and subsurface conditions in this part of Brooklyn consist of fill generally five to 20 feet deep underlain by dense to very dense sand and gravel; in places, with numerous cobbles and boulders which make pile installation challenging. The sand strata that are on the order of 150 to 200 feet thick were laid down by glaciers during the last ice age and have been heavily precompressed. The sand strata are underlain in places by remnants of the Cretaceous-era Raritan Clay formation and Fordham Gneiss bedrock. Because of this, the sand strata generally provide excellent support for shallow foundations and the allowable bearing of five tons per square foot is usually easily justified."

Jan 1, 2016

By Marcus Daubner, Karsten Beckhaus, Florian Bauer

The construction industry can and needs to contribute to a more sustainable world. Accordingly, geotechnical works potentially have a significant share. In this context, Bauer understands “sustainable products for geotechnical works” as those that may cause less emissions and increase the sustainability of construction activities. In order to structure the efforts and systematically pursue sustainable targets in the construction sector, and in the specialist foundation industry, the “17 sustainability goals” presented by the United Nations in their AGENDA 2030, can be used for general guidance and for continuous improvement. Benchmarks for relevant economic and social objectives, mainly with environmental aspects, are inevitable. The key parameter to sustainable products for geotechnical works in the focus of this paper is the optimisation of processes on site needed to fulfill the client’s building task, including the selection of technologies and construction methods with minimum environmental impact and minimum carbon footprint.

May 1, 2022

By Samer Rabab’ah, John C. Niedzielski, Jason Valeria

The PHX Sky Train is an automated people mover system located at Phoenix Sky Harbor International Airport. Phase II of the PHX Sky Train includes the design of over 150 drilled shafts for support of four guideway abutments, 75 guideway piers and three proposed stations. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the elevated guideway above the ground surface, where it needs to pass over roadways, parking lots, an existing terminal, and other buildings. Deep foundation design involves designing drilled shafts within the SGC deposits, some of which extend below the long-term groundwater table. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the project. This paper will present the results of a drilled shaft load test program implemented to provide site-specific measurement of the axial and lateral performance of the project drilled shafts. The load testing program consisted of a bi-directional load cell axial load test and a lateral load test performed on an instrumented test shaft 84 inches in diameter. The development and execution of the load test program and analysis of the test results are discussed. Comparisons were developed between predicted load capacities of drilled shafts using different design methodologies and the load capacity measured from the load tests. The load test results showed that underestimation of the capacity is evident using conventional methodologies. The load testing program was important for verifying the performance of the drilled shaft foundations on the project and was used to reduce the size of the drilled shafts. INTRODUCTION The PHX Sky Train is a five-mile long automated people mover system situated at-grade and on an elevated guideway which connects terminals, parking facilities, a rental car center and the Valley Metro Light Rail system in Phoenix. The purpose of this automated train system is to provide a secondary transportation system within the airport to relieve roadway congestion, minimize wait times and travel times for passengers and provide climate-controlled waiting areas. Phase 1 opened to the public on April 8, 2013. Phase 1A opened on December 8, 2014.

Jan 1, 2019

By Mark A. Rohrbach, Timothy R. Kovacs, PhD Saidin

"Crosshole Sonic Logging (CSL) testing is commonly used to verify the integrity, quality and ultimately the acceptability of the concrete in structural elements such as drilled shaft foundations, secant pile cutoff walls, and secant/tangent pile earth retention structures. Besides concrete quality, many factors can impact CSL test results (e.g. laitance, air temperature, access tube spacing, access tube debonding, etc.). Effective use of CSL testing requires fully informed qualified practitioners capable of distinguishing between abnormal readings unrelated to deficiencies in the drilled shaft concrete and similar readings indicating the presence or possible presence of drilled shaft defects. Based on data and experience gathered from CSL testing of thousands of drilled shafts across North America, this paper discusses such factors and other information useful when evaluating CSL test results, and provides practical recommendations intended to reduce the potential for incorrect test data interpretation. The CSL testing industry is lacking in a clear, universally accepted guideline for the interpretation of CSL data and acceptance criteria of these concrete elements. This paper proposes terminology and a streamlined process for use when atypical results are obtained. The proposed terminology and method are intended to simplify and expedite the submittal review and approval process. Because construction activities for these elements are often on the project’s critical path, the benefits obtained in terms of project savings and reducing costly delays areundoubtedly valuable.1. INTRODUCTIONCSL testing is used extensively throughout the world on many projects to verify the quality of concrete used for drilled shaft foundations, secant pile walls, diaphragm walls, etc. In this paper, these structural elements will be referred to as “drilled shafts,” as they are the most common subject of this test method. In the United States, CSL testing is frequently specified by state and regional transportation agencies, ports, design builders, and others. Although other methods are currently available such as Gamma-Gamma Logging and low-strain Impulse-Echo or Sonic-Echo testing, and new methods are under development such as the Thermal Integrity testing, CSL testing is likely to remain one of the most useful tools for evaluating the acceptability of constructed drilled shafts for quite some time. The popularity of CSL as a testing method can be attributed to two main factors: 1) there is no depth limitation to the method and 2) the apparent ease of interpreting the results. A third advantage of CSL testing is that, when correctly interpreted and with adequate test coverage, it is unlikely to misrepresent a defective profile resulting in acceptance of a defective or inadequate drilled shaft. In other words, CSL testing is very likely to underestimate concrete quality/drilled shaft acceptability within its area of coverage."

Jan 1, 2017