Search Documents

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By E. Paransky, M. Rigaud, G. Paschek, S. Palco

Some of the negative impacts of carbon addition on the strength of castables are yet to be overcome in order to fulfill its potential benefits for oxidation resistance. This paper reports the results of recent studies conducted at CIREP on the effects of different types of carbon additives on the thermo-mechanical properties of magnesia-based castables. Experimental techniques included measurements of the hot modulus of rupture (HMOR), hot modulus of elasticity (HMOE), as well as the wedge-splitting test (WST). The comparison of evolving microstructures was carried out employing scanning electron microscopy with microanalysis attachment (SEM/EDS) and X-ray diffraction (XRD). HMOR values of 12 MPa at 1300°C have been reached in MgO-Si02-C castables containing up to 7% carbon.

Jan 1, 2004

By A. J. Antony Chettupuzha

During a construction project, it is important to ensure that accurate and pertinent knowledge is delivered on time to appropriate personnel. The criticality of documents exchanged or referred to by various parties, evolves over the course of the project lifecycle. Determining the criticality of documents at different stages of the project can aid companies with managing the flow of information in an organized manner, while providing for the detection of potentially disruptive, erroneous material that could result in delays and costs. Therefore, it is crucial to determine documents which have the potential to disrupt a process (by virtue of being incorrect versions etc.) so that they may be isolated or prevented from entering or interfering with the active flow of information in a project, while also ensuring standard revisions of documents are recognized and accessed accordingly. Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project. Analyzing an EPPM system may yield information about the criticality of certain documents within an activity, as well as isolate characteristics peculiar to documents which can assist in risk mitigation. We propose methodology that identifies such critical documents.

Aug 1, 2013

By J. F. Nie

Mechanical properties of precipitation hardenable magnesium alloys depend critically on the chemistry, structure, morphology, orientation and distribution of strengthening precipitates. It is therefore important to gain an improved understanding of these information and their correlations with mechanical properties. Our recent studies indicate that additions of 1-2 wt% of Zn to a Mg-6wt%Gd alloy result in a substantial enhancement in precipitation hardening and in creep resistance. If the strength and creep resistance of the resulting ternary alloy are to be further enhanced for commercial applications, then a detailed characterisation of the strengthening precipitates in these alloys is required. In the present study, the precipitates formed in a Mg-6Gd-1Zn-0.6Zr (wt%) alloy, peaked aged at 250°C, have been characterised in detail using transmission electron microscopy and 3-dimensional atom probe field-ion microscopy. It is found the peak-aged microstructure contains a dense and uniform distribution of precipitate plates that form on the basal plane of the matrix phase and are typically less than 1 nm in thickness. Detailed analyses of the structure and composition of these basal precipitate plates will be presented and discussed in the context of previous work on other Mg-RE¬Zn alloys of similar compositions.

Jan 1, 2006

By G. C. Weatherly, D. S. Wilkinson, A. M. Limarga

In addition to the harsh environment, materials for high-temperature applications are often subjected to a significant mechanical loading. Several researchers have noted that the rate of oxidation can be affected by stress in a range of materials. We have recently studied this effect in y-TiAl, based on the preliminary work of Magnan and Weatherly which showed that nitridation rates on the tensile side of a flexural creep specimen could be 10 times higher than on the compressive side. We have since developed a four-point bending creep setup capable of controlled atmosphere testing. We present quantitative data on the effect of creep on scale growth under a range of atmospheric conditions. Finite element analysis will also be used to show how modest applied stresses can have a large effect on scale growth rates through the generation of large stresses due to the mismatch of creep rate between the metallic substrate and the scale.

Jan 1, 2004

By Q. Dong, S. A. Nightingale

An investigation has been carried out to assess the effects of an applied voltage on the dissolution rate of MgO refractory in a steelmaking like slag. In this study corrosion results obtained from dip tests using a dense direct bonded MgO refractory in a CaO-SiO2-Fe2O3-FeO-MgO slag are presented. These results demonstrate that the application of a voltage across a dense MgO refractory-slag interface can change the rate of refractory dissolution. For the slag composition used and the voltage range tested, it was found that a maximum corrosion rate was obtained at a voltage setting of -0.45V. The results of this investigation have been explained in terms of voltage affects on Marangoni (interfacial tension induced) stirring and its effect on the MgO dissolution reaction that is at least partly controlled by mass transfer in the slag.

Jan 1, 2004

By S. Afshar, C. Allaire

Several studied have recently shown that the use of non-wetting additives is not always a sufficient solution to improve the corrosion resistance of refractories against molten aluminum. Once in contact with liquid aluminum, the coarse aluminosilicate aggregates, which do not benefit from the protective effect of non-wetting additives in the matrix, may be corroded. In some cases, the corrosion of aggregates, especially those containing a significant amount of free silica and/or alkalis, promotes corrosion in the surrounding matrix. The present work explores the possibility to protect the poor corrosion resistant aggregates via a lining procedure. A slip casting method, using either alumina or celsian-like composition based slurries, has been applied for lining of a series of aggregates. The results from this study show that such linings may prevent efficiently the corrosion of aluminosilicate aggregates. This work also analyzes the effects of firing temperature and lining quality on the corrosion behavior of aggregates

Jan 1, 2004

By L. Byszynski

The results of a three month evaluation of the application of EMEW® technology at the KGHM Glogów II Smelter tank house bleed stream are presented. The current, conven¬tional electrolyte decopperization process has some limitations, including: only a fraction of its production is commercial grade cathode copper, significant operating costs, low current efficiency, low current densities resulting in low copper depletion rate, and arsine gas and sulphuric acid emission. The EMEW® cell technology developed by Electrometals Technologies Ltd. can overcome many of these limitations. Tests were performed on a pilot EMEW® installation comprising 30 cells at ambient temperature on electrolyte bleed, using current densities between 100 and 600 A/m2 , with copper concentrations between 45 and <1g/dm3. Results showed that a high grade copper can be obtained to the level of 7 g/dm3 of copper concentration in electrolyte. The use of EMEW® technology allows the direct and efficient recovery of over 85% of the copper contained in the bleed electrolyte. Glue & thiourea addition were tested in order to improve the parameters of the copper depletion process. The behavior of Arsenic and Bismuth was observed and a means for their elimination from the system proposed. On-line copper concentration monitoring is proposed to improve control and performance.

Jan 1, 2007

By P. Bonadia, A. Tabereaux

Nearly all aluminium smelters are increasing the potline amperage to achieve higher aluminium production. In some instances the higher amperage operation has a significant negative impact on shortening the lifetime of aluminum electrolysis cell cathodes due to loss of the protective sidewall cryolite ledge freeze and too rapid penetration of the cell bottom refractory lining by cryolitic bath components due to the higher temperature isotherms. Thus Cathodes require careful thermal modeling of the cathode relining designs and improved refractory materials to allow greater heat loss from the sidewall to preserve a stable sidewall ledge freeze at higher amperages, and the selection of optimum refractory barrier materials to control the penetration and reaction of bath into the cathode bottom refractory and insulation lining. This requires an understanding of the reaction mechanisms and product formation for molten NaF enriched bath and alumino-silicate refractories. It is desirable to use dense, low porosity refractory fireclay firebricks, or similar materials with a sufficiently high silica content to promote the formation the mineralogical phase albite, NaAlSi3O8, that significantly increases the viscosity of the melt which slows the diffusion of reactive species in the melt and thereby retards further bath penetration.

Jan 1, 2004

By I. M. Santos Moraes

The control of minor impurities (mainly As, Sb and Bi) in copper refineries has been a great challenge. Caraiba Metais&apos; copper refinery produces a very high quality copper, registered in LME as grade A, and recognized as amongst the top ten in the copper world. At Caraiba&apos;s Tankhouse Bi and Sb are controlled by means of electrolyte bleed-stream removal after partial decopperizing in a set of electro-winning cells (liberators). Another way of reducing the Sb and Bi content in the electrolyte is by means of the arsenate precipitation chemistry. It is well known that the use of high arsenic concentrations in copper refinery electrolyte has the advantage of causing most of the bismuth and antimony to report in the anode slimes. However, the use of such mechanism of control may contribute to other undesired problems such as antimony and bismuth precipitation in the bulk of the electrolyte, what may cause severe contamination problems. This paper describes a period when some cathode contamination with Sb occurred at Caraiba Metais&apos; Copper Refinery. It also presents an analysis of several process parameters related to the problem, the possible causes for the contaminations as well as the actions taken to correct the problem.

Jan 1, 2007

By Manouchehr Oliazadeh

Talc is used as a gelating, diluting, antimould and softening agent in the pharmaceutical industries. This article reviews efforts made for producing pharmaceutical grade talc from a mine located in the west of Iran, called Masoud Abad. Reaching to the pharmaceutical standards, was the principal goal of the talc beneficiation. Methods such as flotation and leaching were applied to eliminate the impurities. Considering to the negligible Fe content of the ore, the major impurity was calcium carbonate and to some extent dolomite. Depressants used in froth flotation were dextrine, quebraco and sodium silicate. Variation of collectors such as oil petroleum, paraffin, stearic acid were also used. After optimization of the effective parameters, followed by two stages of flotation (rougher and cleaner) acid leaching process was also applied as a complementary step to remove the impurities. CaO impurities in the sample was 11.63% which reduced to 1.03% after two stages of flotation, and finally reached to 0.03% CaO by leaching process. This figure is more lower than the world pharmaceutical standards (i.e. <0.6 % CaO). The highest recovery was 55% at the best conditions. Other impurities (i.e.As, lead, heavy metals ,?) which were at standard levels, confirmed by the authorized health organizations.

May 1, 2001

Planning and operational problems Difficulty in getting accurate geological interpretation Hard to plan work in advance Constant changes in engineering drawings and specifications Occasionally, a small stope portion requires changing the mining method from room-and pillar to shrinkage The ground has to remain stable until the entire stope is mined out A large stope portion is mined as development (30%) Frequent corrective excavation work due to dip changes Unstable and inclined working surface Frequent rehabilitation work is required

Feb 1, 2008

By E. Czech

Hydrogen generated through aluminum-assisted water split reaction is a novel, efficient and environmentally friendly method. It has been found previously that the passivation of aluminum can be prevented in neutral (pH=7) or near neutral pH conditions in water by grinding aluminum with a catalyst, such as A12O3, SiO2 or SiC. Recently, the best results have been obtained by using water-soluble inorganic salts (WIS), ground with aluminum. The massive, rapid corrosion reaction of the Al-WIS system which takes place in regular tap (or marine, or ground) water can be utilized to produce hydrogen by aluminum-assisted water split reaction, in-situ, on-demand. The reaction offers clean, low-cost, environmentally benign and entirely recyclable technology for on-board on-demand hydrogen generation. Besides pure gaseous hydrogen, only pure solid aluminum hydroxides AlOOH or Al(OH)3 are formed as the reaction products. The hydrogen yield and Al-WIS reaction efficiency are high. From 1 g of mechanically alloyed aluminum powder, up to 1.25 liters of hydrogen were generated, i.e. efficiency up to 92% was achieved. The amount of hydrogen and hydrogen generation rate depend on various reaction parameters. The effect of chemistry and concentration of additives, water temperature, powder particle size and milling conditions on the reaction kinetics will be presented and the possible process mechanism will be discussed.

Jan 1, 2005

By M. Fooladi Mahani, M. R. Izadpanah

The knowledge of the thermal shock resistance of refractory materials is of outmost importance due to their wide range of applications in various industries, namely; ceramics, oil refinery, thermal insulation, nuclear power, chemical and petrochemical industries. Thermal shock resistance is measured in terms of the number of cycles that a refractory material can withstand when subjected to sudden temperature changes. This property is measured experimentally by heating a sample of the material and cooling it in a known environment then the number of cycles it withstands this treatment without spalling is a measure of its thermal shock resistance. Although this method of experimentation has long been the practice, but it is both expensive and time consuming. Various studies have been carried out to predict this vital property, however, the rang of applications are limited. The present study employs a test rig by which temperature distributions in magnesite samples are accurately measured. This information plus other results obtained from relevant tests on related properties are used to develop a model which predicts the number of quench cycles withstand by different materials when subjected to sudden temperature changes. The comparison of the theoretical values using the solution of the presented model with experimental data for different materials having different thermal resistance shows a closed agreement.

Jan 1, 2004

By R. Pelletier, Herny. E., C. Allaire

Corrosion of refractory linings by molten metals is controlled by interactions between penetration and chemical reaction. Corrosion of aluminosilicates by molten aluminium is no exception. The early stage of corrosion can be described as a particular case of reactive wetting over a porous medium. Although the reactivity between aluminium and silica is great, which should improve wetting and penetration, the presence of air and the formation of a protective oxide layer disfavours initial penetration. This paper presents the results of an exploratory study on the effect of some parameters on the initial stage of aluminium penetration. Penetration kinetics and metal intrusion tests have been performed on alumina and silica powders with pure aluminium and Al¬5%Mg. Capillary models are used as tools of interpretation. Penetration kinetics tests had a poor reproducibility and the kinetics itself can not be explained very well by the capillary-tube-bundle model. On the other hand, a capillary model initially developed for ice intrusion into freezing soils produced predictions in reasonably good agreement with intrusion pressure measurements. The effect of particle size and alloy composition can be predicted using this model. However, the effects of temperature and powder chemistry need additional interpretations to be rationalised. An unusual resistance to penetration of silica powder by molten aluminium have been observed in a series of experiments. This led the authors to the strange conclusion that oxygen should be seen as an excellent non-wetting agent and that there might be ways to use it in industrial applications.

Jan 1, 2004

By Frank Wright

"The Icon Sullivan Joint Venture ore deposit was discovered in June, 1965 by Messrs. Paul Benard, Bob Galipeau and Mac Watson working under the direction of Mr. Andrew J. Troop, as employees of the Icon syndicate. The deposit is located on the Waconichici River as the south end of Baie du Poste of Lake Mistassini, approximately 45 miles north of Chibougamau. Property acquisition and Winkie drilling was followed by a diamond drilling program to evaluate the deposit. Stripping of the open pit area connnenced in the late fall of 1966 and the first test sample of ore was shipped to Chibougamau in December of that year.Regular ore shipments to the mill of Merrill Island Mining Corporation Limited for concentration commenced May 25, 1967. Production to December 31, 1970 amounts to 42,960,000 pounds of pay copper.The ore is chalcopyrite in white quartz dolomite, and it contains a very small amount of precious metals. The quartz dolomite assumes a flat to gently dipping attitude and is associated with a graphitic argillite contact zone on both hanging and footwall sides, in dolomitic limestone rocks. There is practically no other sulphide present in the ore.During the summer of 1969 a series of pre-concentration tests were completed and a Wemco heavy media sink float plant was installed in late 1969 and early 1970. This pre-concentrator eliminates at least one third of the ore mined in the form of barren quartz dolomite prior to ore shipment by truck to the concentrator in Chibougamau."

Jan 1, 1971

World copper electrowinning tankhouse plant practices have been surveyed. This survey is a supplement to previous surveys that have been carried out in 1995, 1999, 2001, 2002 and 2003. On a world basis, process technology trends include the further installation of automated electrode handling systems including permanent cathode systems, automated cathode handling machines, fully automatic cranes and polymer concrete cells. Designs also have included larger electrode sizes and higher electrolyte flows and current densities. Overall these trends have further resulted in optimized tank house productivities and improved electrowon cathode purity. Most greenfield copper electrowinning projects are occurring in South America and Central Africa.

Jan 1, 2007

By Agbo Chima

Low-lying sections of open-pit mines accumulate water, especially during the rainy seasons, preventing access to resource-bearing areas. To sustain mining operations, the water must be lifted out of the flooded pits at a high flow rate using pumps. These pumps need to be mobile so that they can be removed during drill-and-blast operations. Most mobile pumps rely on diesel engines with high maintenance requirements. A special pump design was developed to address the unique needs of open-pit mining while making the dewatering process more sustainable. Using the target flow rate and head data, an efficient pump was designed, encased, and deployed in the open pit. A variable speed drive (VSD) was installed in a protective skid so that the pump could be tuned to match the preferred flow rate at any point during its operation. This system was tied to the national electrical grid instead of being powered by diesel pumps, which reduced the carbon intensity per kilowatt-hour. The high availability, low maintenance requirement, and greater reliability reduced the use of spare parts, the fuel consumption, and the logistics associated with operating the pump. This further reduced the carbon footprint of the dewatering process. This paper provides some of the two-year performance metrics for a deployment in West Africa. With a focus on availability, maintenance costs, average cost per volume lifted, and carbon footprint, this encased pump system is compared to the diesel-driven pumps that it aims to replace.

Jan 1, 2023

By N. Maleki

In recent years, research and development of magnesium alloys have been greatly promoted by the lightweight requirements in critical industries. The use of these alloys, however, has been restricted by their limited mechanical properties especially at high temperatures. The disadvantages can be overcome by producing Mg matrix composites. The Mg?Si alloys containing in situ Mg2Si particles have found a great potential as structural materials. Unfortunately, Mg2Si compounds are prone to form undesirable coarse Chinese script morphologies, which would deteriorate the properties of the materials. Refinement of microstructure is performed for improvement of wear and corrosion resistance. This paper investigates the microstructure and corrosion behavior of pure magnesium, unmodified and modified magnesium matrix composites reinforced with Mg2Si particles. The Mg2Si/Mg composite was prepared via a normal cast route, and then various amount of zinc was added to melt in order to modify the Mg2Si reinforcement particle morphologies. The microstrucrures were characterized by optical and scanning electron microscopy followed by EDX analysis. The corrosion behavior of Mg/Mg2Si composite was investigated by using potentiodynamic polarization measurements. The results showed that by addition of zinc, the average size of the primary Mg2Si became significantly decreased from about 100µm to about 20µm, as well as its morphology changed from dendritic to a polyhedral shape. However, by adding extra amount of zinc many primary Mg2Si particles become coarse again. It was also found proper amount Zn addition increased the corrosion resistance of Mg/Mg2Si composite.

Oct 1, 2011

By W. Lamb

Feed Preparation ? Five primary parameters affect the screening efficiency ? Ore characteristics ? Operational characteristics ? Screen characteristics ? Water addition and washing ? System design

Apr 1, 2005