Search Documents

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

The scanning electron microscope (SEM) was primary developed for imaging applications. With the introduction of the Si(Li) energy dispersive spectrometer (EDS), simultaneous imaging and x-ray microanalysis became possible. However, long working distance and high current were needed because the position and small solid angle of the EDS detector. The high spatial resolution is generally obtained at short working distance with a SEM. Unfortunately x-ray microanalysis is never performed in the best imaging conditions. The annular silicon drift detector system is inserted below the objective lens which gives a higher solid angle (up to 1.3 sr). In consequence, a lower working distance and probe current can be used. An improved spatial resolution becomes possible during x-ray microanalysis. With this x-ray detector installed on a cold-field emission scanning electron microscope, quantitative x-ray microanalysis with high spatial resolution at low beam energy and low current becomes possible with the possibility of using the various different type of imaging at the same time. Also, since the count rate can be as high as 1,500 kcps, which lowers significantly the detection limit of elements as well as the minimum feature sizes of different phases that can be distinguished.

Jan 1, 2014

By E. W. Johnson

"The current increase in gold price may presage a resurgence of gold milling plants in Canada similar to that of the thirties. Because the industry has been at a low ebb for almost two decades, future operating responsibilities will likely devolve upon personnel with limited cyanidation experience. My comments, which may seem elementary to experienced operators, are directed towards these industry newcomers to highlight operational features in cyanidation which forty years' experience has shown me to 0e of importance. A brief review of what actually takes place in a cyanide circuit may help give a better understanding of the topics to be discussed.These will include: (1) expose the gold (2) dissolve the gold(3) make solid/liquid separation(4) recover the gold from solution.1. Expose the GoldThe chemical key to gold recovery by cyanidation lies in the ready solubility of the metal in a relatively weak solution (0.04%-0.075% NaCN equivalent by weight) of calcium or sodium cyanide. Obviously, dissolution cannot start unless the cya1ide is in contact with the gold. As an analogy, the yolk of a hard-boiled egg can oe taken to represent the gold particle and the egg white and shell, the surrounding gangue or sulphide host. As the sl1ell and white must be fractured to expose the yolk, similarly the surrounding gorngue or sulphide host must be broken or fractured to enable the cyanide solution to contact the gold."

Jan 1, 1979

By Andreea Catalina Gluhoi

The oxidation of propylene and methane has been investigated over two series of Au/MOx/Al2O3 and Au/MIOx/MIIOx/Al2O3 catalysts (M, MI, MII =Li, Rb, Mg, Mn, Ce, Zr). Whereas the effect of the presence of MOx or MOI x/MOII x on the oxidation of methane is relatively small, a large enhancement in activity is observed for propylene oxidation. Synergistic effects have been observed by combining ceria or a transition metal oxide (high oxygen storage capacity) with an (earth) alkali metal oxide.

Oct 1, 2003

By C. T. Wiliams, John B. Bush, John Lamb

"THE TOWN OF HEDLEY is in the valley of the Similkameen River, about 200 miles east of Vancouver and 25 miles north of the International Boundary between British Columbia and the State of Washington. The main ore deposits are located on Nickel Plate Mountain, northeast of the town.The outcrop of the Nickel Plate system of orebodies is at an elevation of 5,900 feet. It was discovered in 1898 by prospectors and sold in the following year to the Marcus Daly interests of Butte, Montana. Production commenced in 1904 under the name of Daly Reduction Company. In 1909 control passed into the hands of the Hedley Gold Mining Company. Operation of the mine continued until 1930, when exhaustion of known ore reserves forced it to close. Upon the recommendation of Paul Billingsley (3) the mine was optioned by the 1. W. Mercer Exploration Company in 1932. Production began once more in 1934 under the name of Kelowna Exploration Company Limited, and was practically continuous until August 1955, when the mine was again shut down. The name of the latter company was changed in 1951 to Kelowna Mines Hedley Limited.The Mascot Fraction, a small wedge-shaped claim lying astride the Nickel Plate orebodies, was mined by Hedley Mascot Gold Mines Limited between 1935 and 1949. The geological setting and structural control of ore are essentially the same as in the adjoining Nickel Plate Mine.Total production from all operations on Nickel Plate Mountain to the end of 1954 was approximately 3,800,000 tons of gold ore, with a gross value in excess of $48,000,000.General GeologyNickel Plate Mountain occupies the gentle westerly dipping limb of an asymmetrical anticline, the axis of which trends northeasterly. The rocks are composed of a thick pile of Triassic limestone, limy argillite, and quartzite, -resting on a flattish floor of granodiorite near the base of the mountain. Associated with these sediments is a host of porphyritic sills and dykes of gabbro-diorite composition. In the mine area east-west brown soda-rhyolite dykes and north-south black andesite dykes crosscut all the other formations and the ore, probably following steep later fractures."

Jan 1, 1949

By José Cáceres

Mine To Mill? ? Carlisle(1954) ?The economic of a fund resource with particular reference to mining?. ? Steine(1978) ?Coarser grind may mean lower metal recovery but higher profit?. ? Metalica (1999) ?Mine Plant Integrated Planning?. ? JK (2002) Mine to Mill Strategic Planning ? Camus, Kelebek (2002) ?Management of Mineral Resources: Creating Value in the Mining Business?. ? Caceres (2003) ?Integrating Milling Parameters in the Mining Planning?

May 1, 2006

By C. Cortés

Flotation is a highly interactive process where a change or disturbance in any part of the circuit results in different final grades and recoveries. This high variability of the circuit metallurgical performance complicates the diagnosis of the scavenger stage at the end of the line, as copper losses in the final tailings are erratic and not totally a consequence of problems in the scavenger section. The assessment of the scavenger performance requires a more elaborated procedure than that used for others stages of the circuit. This communication describes the application of an approach that combines results of laboratory flotation tests with those of surveys performed at the plant. The approach is based on running surveys in one of the circuit lines to collect samples for determining grade vs. recovery curves for total mass and size-by-size fractions. Full mineralogical and liberation analyses are also considered on some samples of the feed and tailings streams selected to have a range of feed grades. A separate sample of the feed is used to run laboratory flotation tests to determine optimum flotation time. Two additional pieces of information are the effect of operating variables on recovery, determined through a test program based on design of experiment techniques, and operational data on every cell in the line gathered by visual observation. The application of this approach to one of the scavenger lines at Los Colorados concentrator (Minera Escondida, BHP Billiton) is demonstrated.

Jan 1, 2007

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By M. Coleman, M. E. Reed

The control of feed delivery quality to the flash furnace remains an unsolved problem. Many operations around the world still have limited control of feed quality to their flash furnace. Schenck Process and WorleyParsons continue to work towards the ‘holy grail’ of simple quality feed delivering both radial feed distribution and pulseless feed delivery. Ten years ago they joined forces to offer a system based on then Clyde Process RotoFeed system which could deliver ground level installation, online mixing of materials, pulseless feeding direct to the burner, with good radial distribution. Unfortunately, this proved to be too large a step for the Flash Smelting community and met with resistance from the process owners. Since then the community has developed a range of options some of which have been implemented over this period. Despite these improvements there are still areas of concern including safety issues associated with concentrate leaks and spills, uncontrolled variations in feed rate including massive flooding events, intermittent distribution improvement and set up of the burner continues to be trial and error and hard to repeat the success in each burner campaign. These continue to impact flash furnace performance globally on a daily basis. Following the community reticence to pursue the complete solution a number of interim steps are now available to pave the way to the ultimate feed system. The mixing of material has been installed and is delivering line blended materials on a daily basis. This paper will investigate the developments over the last 10 years and discuss the pros and cons of this incremental step process for overall furnace control. INTRODUCTION Schenck Process and WorleyParsons have continued to interact and observe changes in the flash smelting industry and to consider application of the Clyde RotoFeed now incorporated in the Schenck Process ProStreamTM range for delivery of feed directly to the concentrate or matte burner. Schenck Process pneumatic injection from the Clyde Process range, ProStreamTM, utilises two types of volumetric feeders to accurately control the feed of material into an injection pipeline. These are referred to as the RotoFeed and RotoScrew technologies and the choice of feeder type is dependent on the characteristics of the material to be handled. The RotoFeed is generally used for finer, granular and powdered materials which cannot be accurately handled with a screw such as pulverised coal and copper concentrate, whilst the RotoScrew is particularly suited to coarser lump materials, particularly abrasive of cohesive materials like zinc powder, electronic scrap and metal ashes. Both units can operate at high pressures and many systems work at 3 to 10 bar with the occasional system working at 20 or 30bar for carbon to gasifiers. For the Flash furnace the ProStreamTM units can be used to deliver each of the furnace feed materials into a single line, mixing the materials homogeneously and live to the burner.

Jan 1, 2019

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By K. Bunney, R. Pleysier

The deportment of a suite of elements through representative gold ore processing unit operations in cyanidation has been investigated. Chromium and lead are not soluble in alkaline cyanide solutions. Arsenic, antimony, cobalt, molybdenum, selenium, tellurium and vanadium are soluble, but typically do not adsorb onto activated carbon to any appreciable extent. Silver, copper, cadmium, mercury, nickel and zinc to varying extents report along with the gold to the carbon eluate. Cadmium, mercury and zinc can report to the carbon regeneration kiln off-gases. Strontium is soluble and adsorbs on carbon where it remgins.

Jan 1, 2011

By P. Mattar

The geotechnical importance of studying fluid flow through porous media and soils in particular, becomes evident when dealing with groundwater movement in surficial geomaterials that can be initiated by hydraulic gradients that develop during construction activity, groundwater extraction, impounding of reservoirs and groundwater recharge during adverse climatic events. In a geotechnical context, rocks are regarded as virtually impermeable materials, with comparatively greater resistance to flow of water through their pore structure. The importance of the permeability of rocks comes to the forefront when deep geologic formations are used in geoenvironmental activities for disposal of hazardous and toxic materials. The permeability of the rocks encountered is of critical importance to these geoenvironmental activities since the movement or transport of the hazardous materials during their eventual release will be largely governed by the permeability characteristics of the geologic formation. The estimation of the permeability characteristic of geologic formations is a non-trivial exercise since the measure of permeability can be influenced by the scale at which the measurement is made. Regional-scale and borehole-scale estimates of the permeability can be greatly influenced by the inhomogeneities, including fractures, fissures, solution channels and other anomalies that are present in naturally occurring geologic media. These anomalies are considered to be site specific and can only be determined in a reliable fashion by either conducting tests at the appropriate scale or in the regional-scale through inverse analysis of tracer movement patterns in rock masses. The estimation of the permeability of intact units of a geologic medium has important geoenvironmental applications in connection with storage of wastes since the units in which repositories will be located should be sparsely fractured and the sealing of the fractures and fissures are a prerequisite to developing an efficient solution for storage. The intact permeability of geomaterials is therefore regarded as an important property that influences efficiency and reliability of geoenvironmental solutions for deep geologic disposal. The permeability of geomaterials such as concrete and cementitious grouts are also important to many geoenvironmental and infrastructure applications where durability of structural materials in general and cements used for sealing deep boreholes and other access shafts employed in waste management endeavours is influenced by the permeability characteristics of these materials

May 1, 2009

By L. Hacini, N. Van L ê, P. Bacher, D. Thibault

Manufacturer welded components may suffer from high level of residual stresses which can cause premature cracking and decrease the life of the components if they reach values close to the yield strength of the material. In the present work, a robotized hammer peening technique is simulated by an impact machine and the residual stresses generated by the indentation are measured. To better understand phenomena behind residual stresses relaxation by hammer peening, the impact energy level was changed. 304L steel plates were hammer peened with 10 impacts. The contact between the hammer and sample surface was always at the same location. The strains on the surface close to the impact location were recorded during the test using strain gauges to follow residual stresses variations. At the end of the test residual stresses were measured indepth using hole drilling technique at 8mm from the impact center. The micro-hardness was monitored to evaluate the affected zone by the hammer peening. This approach gave a good estimation of the energy and number of blows to be used for efficient relaxation of the manufactured parts.

Jan 1, 2006

By Roger Lacroix

Fuel cell application to mining has been indicated to be potentially beneficial to underground mine worker health and to energy efficiency. In order to define the economic advantages of using hydrogen fuel cell vehicles, a detailed study of operating and capital costs associated with underground loaders and power supply infrastructure has been carried out. The results show that for a typical medium-size mine, operating costs and infrastructure costs are less for the fuel cell option versus diesel. The reverse occurs for capital costs owing to the currently higher cost of fuels cells versus diesel engines. This disparity is expected to decrease given the decline in price associated with fuel cell technology advances. Related market issues for fuel cell manufacturers are also presented. Despite the difference in cost, the resources and mine infrastructure required to operate loaders, and base design of the mine loader, is similar for diesel and fuel call versions.

May 1, 2007

By D. Djokic

One of the most attractive features of electron beam curing as a process for manufacturing composite structures is the potential for attaining very low levels of residual stress as compared to thermal curing. This residual stress reduction is important both for the potential to reduce composite failure strains at low operating temperatures and the associated reduction in process-induced deformation. Previous work has demonstrated that it is possible in some cases to significantly reduce residual stress development during irradiation and also avoid development of additional residual stress during post cure. In this paper, simple L-shaped composite laminates were used to study the development of residual stress and deformation during thermal post-cure of specimens that were already partially cured using different radiation doses. Following post-cure, these specimens were also subjected to high-temperature loads to study creep behaviour under service conditions. Aerospace

Jan 1, 2006

By Z. D. Hora

Commercial production of barite commenced in British Columbia in 1940; shipments have been recorded from ten deposits, of which four are particularly significant: The Brisco, Silver Giant, Parson, and Mineral King mines. Parr of the barite production is a by-product of base metal deposits in which barite is a major gangue mineral. About one hundred occurrences are known. COMMERCIAL production of barite in British Columbia dates back to 1940. Production volumes rose and fell and reached 39,900 tonnes in 1972. The main producer is Mountain Minerals Limited . There are two principal areas of barite deposits in British Columbia: ( I) The southeast part of the province along the Rocky Mountain Trench , which is the source of all production to date. (2) Stratabound occurrences in northeast British Columbia in the Gataga-Ketchika rivers and Muncho Lake areas which are not yet developed. Of the approximately one hundred reported barite occurrences, only ten have recorded commercial shipments, some of insignificant amount. So far, four deposits have proved to be important producers: Brisco, Silver Giant, Parson and Mineral King. The Mineral King property is situated near the confluence of Toby and Jumbo Creeks, 35 km southwest of lnvermere. The lead-zinc-copper-iron-barite deposits, as described by Fyles (1959, 1962), replace Proterozoic Mount Nelson dolomites of the Purcell system on the limb in the trough of a complex, tight syncline. The mine operated from 1954 to 1967 and 2,097,900 tonnes of baritic ore that was processed for base metal concentrates and also produced 22,680 tonnes of by-product barite. Since 1970, some 136,000 tonnes of barite have been recovered from the old tailings pond. The deposit is now considered depleted. The Silver Giant mine is located 10 km northwest of Spillimacheen. Barite and lead-zinc sulphides replace Cambrian Jubilee limestone near their contact with the overlying Ordovician McKay slate. Mineralization is located in the nose of an overturned plunging anticline. Between 1951 and 1957 800,000 tonnes of baritic ore were processed for lead and zinc concentrate. After 1959 barite was also produced , first from open pit, and later from reworked tailings. Up to 1979 production of barite totalled approximately 180,000 tonnes. Two other producing mines in the area are descri bed by G.R. Manson (this volume). Large, bedded stratabound barite deposits are reported from northeastern British Columbia. Six major shale-hosted Industrial Minerals in Canada lead-zinc-barite occurrences are known in the Devonian Gunsteel Formation. These are: Driftpi le Creek, Mount Alcock, Cirque, Pie, Fluke and Elf. In addition, numerous occurrences of strati form blebby or nodular barite and locally massive white crystalline barite are known from the Driftpi le Creek and Ak ie River districts in Gunsteel shale and from the Kechika, Road River and Ware map areas from Silurian siltstone . The size of these deposits is impressive; the baritic horizon at Mount Alcock is reported to be 25 to 30 m thick , and dri ll ing results from the Cirque deposit indicate reserves of 30 mi llion tonnes of baritic lead-zi nc-si lver ore. Similar bedded barite deposits are also reported from Midway area, near the Yukon border.

Jan 1, 1984

By F. F. Roberto

Sulfuric acid has been demonstrated to be an efficient lixiviant for in situ extraction of copper in the past. It has also been proposed that microbial production (by iron-oxidizing acidophilic bacteria) of acidic ferric solution either in situ or ex situ could provide an economic strategy to generate an effective lixiviant for secondary copper sulfides like chalcocite and covellite. Copper heap bioleaching also takes advantage of this approach. One of the major environmental challenges for in situ copper recovery projects is the containment of acidic solution within the ore deposit, and ultimate restoration of the depleted ore body to its original state. A perhaps overlooked aspect of projected site operations is the possibility that transient acidic conditions and pumping of solutions from surface reservoirs into the subsurface could stimulate the growth of iron- or sulfur-oxidizing species of acidophilic microbes in the ore body, leading to additional generation of sulfate, acid, and ferric iron. This outcome would benefit extraction of copper in mixed oxide/sulfide deposits in the near term, but could complicate restoration activities. Possible impacts of pumping acidic solutions into the subsurface on microbes resident in, or introduced into the extraction zone will be discussed in the context of our understanding of copper heap bioleaching and acid rock drainage. INTRODUCTION As high-grade deposits of metals such as copper continue to decline, conventional mining methods have evolved to mine and process larger and larger quantities of ore. What is currently defined as ore today often contains less metal than the tailings of past operations. The throughput of current-day mines also leads to tremendous amounts of waste rock and tailings that may threaten the environment and communities around the mines, as has recently been experienced by 3 major tailings disposal facility (TSF) dam failures in the past 5 years. Community acceptance of large mine operations thus becomes more difficult to achieve—loss of the social license to operate. In response, the mining industry urgently pursues innovations that can fundamentally change the way in which metals are mined. In situ recovery (ISR) of metals represents one approach to a more sustainable mining industry, by virtually eliminating the need for a pit or underground excavation, eliminating the excavation and transportation of ore to a process plant and the ensuing noise and dust that is generated, and any need for waste rock dumps or TSFs. An ISR mine could have very little visible footprint beyond a network of wells, pumps, and piping to transport pregnant solution to a recovery facility, such as a solvent extraction- electrowinning (SX-EW) plant for copper. Some solid waste streams and/or storage ponds may still be necessary to treat and store bleed streams, PLS and raffinate, or as part of groundwater restoration activities. Thus capital and operating investments would be potentially much lower than that required for a conventional mine. In theory production could also be controlled to adjust to subsurface ore grade and match market demand. A not insignificant challenge of in situ recovery is the requirement for an efficient, low-toxicity, and ideally selective lixiviant for the metal that is targeted.

Jan 1, 2019

By Seunghoon Lee

The increase in the number of higher and larger buildings is expected to require the buildings' outer wall maintenance process, which includes cleaning, painting and monitoring, still depends on manpower. In this study, we proposed the robotic building maintenance system and aimed to reduce the jerk effect through the motion control of the system, improve the performance of the maintenance task, and ensure longer life and safety by improving the stability of the building structure and robot system. Through the results of the motion control and field-test with the proposed system, in specific, horizontal sliding module (HSM) showed that the jerk oriented by impact force was significantly reduced, feasibility of the proposed method was verified, and the robotic challenges were explored.

Aug 1, 2013

By Shahé Shnorhokian

Numerical modeling is increasingly being used as a tool to examine complex geomechanical issues related to rockmass behaviour and stability of underground openings. The in-situ stress regime and the evolution of mining-induced stresses during the life of an operation, taking into account the planned stope sequence, are topics that can only be handled through the use of a realistic and calibrated numerical model. This paper presents a case study of a deep underground Canadian mine in northern Ontario. A FLAC3D model was constructed and calibrated based on in-situ stress measurements. In the first stage, the evolution of stress regime was studied and compared with the occurrence of rockburst events during a period of three years. The locations of clusters were examined and compared to the mining sequence during that period. In the second stage, stresses within a diminishing ore pillar were examined based on the planned stope sequence and compared to levels deemed acceptable to the mine. Based on the results, an alternative sequence was arrived at to reduce stress accumulation in the pillar, or induce it to occur at a further distance from a brittle dyke in the vicinity of the orebody.

Aug 1, 2013

By Wayne F. Luinstra, Frédérique Vincent, André R. Laplante

"A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; possible uses are discussed. A case study of how the technology was used at Hemlo Gold Mines is presented.IntroductionUsing gravity to supplement either flotation or cyanidation is a well established practice in the gold industry. It differs from most recovery circuits in that most of the gold recovered by gravity would be recovered in any case by the circuit downstream, be it flotation or cyanidation. The economic justification of gravity is therefore based on small margins (for example. a net smelter return of gravity gold of 99%, as opposed to 94% by flotation). It was easily demonstrated when either flotation or cyanidation were relatively inefficient processes, and labour costs low (as gravity can be labour intensive). Over the past thirty years, the advent of better flotation machines (flash, column, high capacity), more effective collectors, and better control systems has increased flotation's metallurgical performance, thereby decreasing the incentive for gravity recovery. Cyanidation technology has undergone similar changes, with the advent of activated carbon, oxygen and lead nitrate addition, and improved impeller design.Today, gravity could remain an attractive option only inasmuch as it can be implemented with very low capital and operating costs. This has resulted in a relative shift away from gold gravity recovery (except for alluvial deposits), in the seventies and eighties. For example, as of the early nineties, gold gravity recovery has disappeared from the typical South African flow sheet. The advent of the Knelson Concentrator, at the beginning of the eighties, foreshadowed a resurgence of gravity recovery, as gold's grinding and classification behaviour (Banisi, Laplante and Marois, 1991) makes it possible to achieve adequate gold recoveries with very simple, Knelson based, gravity circuits (Laplante et al., 1994).Consider for example the Hemlo recovery circuit, made of a single 61 cm x 122 cm (2' x 4') screen, an automated 76 cm (30"") Knelson feeding a Gemeni table, to produce a 70-80% Au concentrate which accounts for approximately one fourth of the gold production (about 3 million grams per year). The low capital and operating costs make it possible to justify the gravity circuit on the basis of savings in other operating costs (e.g. fewer carbon stripping and reactivation cycles). Any improvements in recovery, which would at Hemlo be difficult to measure, would be additional benefits. Such a circuit is rapidly becoming a standard in Canadian and Australian operations.The justification for installing a gravity circuit must be first based on an estimate of how much gold it will recover (irrespective of what the potential benefits are). This is a function of the nature of the gravity circuit to be installed; however, Knelson circuits, by their very simplicity and efficiency, limit the options. This leaves the amenability of the ore to gravity recovery as the single most important parameter. Various approaches can be used to characterize this response (Woodcock, 1993). The present work sought a route which would fulfil the following criteria:"

Jan 1, 1996

By Enrique Rubio

Several mining operations are currently evaluating the feasibility of changing their mining method to Block Caving. There will also be several deep low-grade ore bodies that will face the need to go underground in following their ore to depth. There are two main reasons why Block Caving is attractive: firstly, it offers the lowest operating costs amongst all the mining methods; and secondly, it is truly a massive mining method, offering the highest potential production capacity. Despite its longstanding popularity, there are still significant components of the method that are not clearly understood. Also, the lack of availability of key geomechanic information still presents a major obstacle to developing mine planning and production scheduling. There are several key issues in block caving that can make it feasible such as cavability, fragmentation, stresses will condition the way that a block caves and the way that material is drawn from the draw points. Consequently Block Cave mining method is a good example where the ore body has to be related to design and mine planning. The concepts of dilution, draw control as well as sequence definition are reviewed in this paper to illustrate the idea of integration. There have been some examples of mines where some of the components of mine planning have not been integrated causing a disaster in terms of economics or safety. Different layouts configurations might give a different result in the planning of the mine

May 1, 2002