Search Documents

By Andrew J. Neale, Brian C. Flintoff

"In most mineral processing operations the term ""audit"" is usually reserved for the exercise of checking financial records and/or safety practices. While these activities are time-consuming, no one disputes their necessity or value. If these areas are subjected to such careful scrutiny, why is it that the same principles are not normally applied to critically examine process operation. After all, the operating efficiency of the plant impacts directly on the measures of profitability.A mineral processing plant is a complex system that has a number of distinct, but mutually dependent elements: process equipment, instrumentation, operating policies, maintenance policies, control strategies and people. To ensure maximum economic performance in the dynamic environment that characterizes a concentrator, requires a periodic review of each of these areas. However, to be useful, the study must be based on sound metallurgical principles and be conducted in a highly focussed manner. Experience has shown that the exercise is very revealing and rewarding.This paper will discuss the plant audit process and illustrate its potential value through examples taken from plant studies."

Jan 1, 1992

By R. Pakalnis, H. Miller, Madill. T.

"This paper describes a methodical approach to the estimation of the orientation and the magnitude of in-situ stresses. The study was performed at the Ruttan Mine, Sherritt Gordon Mines Ltd. , a 6,000 T.P.D. underground operation, located in northern Manitoba, Canada. It involves an initial estimate to be made based upon: structural interpretation • virgin stress measurements conducted in other areas (world wide, regional)The verification of the prevailing stress regime was made by conducting CSIRO hollow inclusion(1) overcoring measurements. The current cost for a virgin stress determination is about $7000 per measurement(2) and the difficulty encountered in attaining a good reading is high. This paper will describe the analytical procedures employed at Ruttan in evaluating the in-situ stress magnitude and orientation based on three overcore tests. It is proposed to perform an additional six measurements in order to verify the following results:Vertical stress = av (MPa) = 0.027 by depth (m)Major principal stress = o! """" 2.5 xav (340°/-20°)*Intermediate principal stress = a2 - 1.2xav (070°/0°)Minor principal stress = a3 """" o.8xov (160°/-70°)IntroductionThe Ruttan Mine of Sherritt Gordon Mines Ltd., a 6,000 T.P.D. underground operation, is located in northern Manitoba, Canada (Fig. I). The Ruttan copper-zinc orebody is a multi-lensed, steeply dipping (70 degrees) en-echelon deposit. Individual lenses have a maximum strike length of 350 m with widths varying from 7 m to 61 m. The mining method is o pen stoping with delayed backfilling and extends from surface to 860 m below surface."

Jan 1, 1985

By D. Lessard, S. Nantel

"Surface crown pillars are important Canadian,mining structures. Mines operating in the Canadian Shield usually have several, forming a first line of protection from surface elements.Detailed technical information from twenty-four Canadian hard rock mines show that the deposits dip steeply and are generally either single or multiple veins. Considerable overburden usually cap the deposits. The rock mass is often altered and intersected by important discontinuities.The designs for these types of pillars lack basic data and are based on experience rather than a scientific approach. Regardless of the competence of the rock mass, the surface crown-pillar thickness to width ratios (an unscientific design tool used by the industry) are usually less than five. Rock bolting is, in almost every case, used as a support measure. However, there are many openings neither backfilled nor monitored.The characteristics of openings with surface crown pillars are also examined."

Jan 1, 1988

By J. S. Scott

"The Quemont property comprises 640 acres lying directly north of and adjoining the Noranda (Horne) mine. During 1926 to 1928, United Verde Extension Mining Corporation sank a shaft 235 feet and did 3,000 feet of development work on the 215-foot level. Between 1929 and 1930, Quemonr Mining Corporation deepened the shaft to 926 feet, and did further lateral work and drilling on the 500- and 900-foot levels. This work was confined to an area close to the south boundary and met with little encouragement.Following a period of idleness a magnetic survey was made in the winter of 1944, followed in the summer of the same year by some 6,000 feet of drilling. The first successful hole was drilled in February, 1945, from the ice of Osisko lake.To the time of writing, 131,000 feet of drilling, surface and underground,have indicated a large tonnage of gold-silver-copper-zinc ore, and although some knowledge of the geology and structure is emerging, it is too early to draw definite conclusions. The following brief description deals only with those structural features that are reasonably well indicated."

Jan 1, 1954

By P. Chu, J. A. Finch, R. Li

"Bubble size plays a key role in flotation. In this paper, we examine the possibility of using passive acoustic sending to determine bubble size. Software was developed based on Short Time Fourier Transformation (STFT) to analyze the frequency of the acoustic signal emitted from the bubble formation event. Bubble size was determined from the Minnaert frequency. The acoustic-determined bubble size responded to reagent dosage, but was less sensitive than that given by imaging. The constraints of the current acoustic approach are discussed.INTRODUCTIONBubble size is an important factor affecting flotation performance. It determines the maximum available surface area for collecting and transporting mineral particles. Of interest for process control (Gorain, Franzidis, & Manlapig, 1995), it can be determined by several techniques, such as image analysis (Grau & Heiskanen, 2002; Hernandez-Aguilar, Gomez, & Finch, 2002); conductivity (Barigou & Greaves, 1992); drift flux analysis using gas rate and gas holdup measurements (Banisi & Finch, 1994); and optical sensors (Randall, Goodall, Fairlamb, Dold, & Connor, 1989). However, all these techniques have drawbacks.Acoustic analysis of the oscillatory behaviour of bubbles to extract bubble size is another possibility (Leighton & Walton, 1987; Pandit, Varley, Thorpe, & Davidson, 1992; Al-Masry, Ali, & Aqeel, 2005; Manasseh & Ooi, 2009; Leighton & White, 2012; Spencer et al., 2012). The fundamental basis is the work of Minnaert (1933) who first correlated the bubble size with its natural frequency, Equation 1:"

Jan 1, 2016

By Gennaro Delisle

"Les Services TMG (Niobec) currently treat a niobium ore in the Chicoutimi area of Quebec. The mineral pyrochlore is present in a carbonatite deposit which assays 5% to 7% apatite.The ore is ground to minus 65 mesh and deslimed at 10 micrometres. Part of the carbonates are floated with a fatty acid emulsion and rejected to the tailings as a first step to ensure the proper conditions for the flotation of the pyrochlore concentrate. The carbonate concentrate is 65% minus 44 micrometres and is composed of dolomite, calcite, 22% apatite and a minor amount of silicates.A laboratory investigation was undertaken to determine the feasibility of extracting apatite from the carbonate concentrate. This led to the development of an economic flowsheet to produce high-grade apatite concentrate. The apatite is depressed with phosphoric acid, and the pH is adjusted at 4.8-5.0 with sulphuric acid. An additional amount of fatty acid is added to permit efficient flotation of the carbonates. 1n a second stage, the silicates left behind with the apatite concentrate can be removed by depressing the apatite with AIC3 while floating the silicates with a secondary amine.The results of the laboratory tests indicate the possibility of producing an apatite concentrate assaying 38.3% P2O5 (83.7% BPL) with a recovery of 66.2%. Pilot-plant tests undertaken at the concentrator yielded a concentrate of 34% P205 and recovery of 76%."

Jan 1, 1981

By Howard Keele

"The Whitewood Mine near Edmonton, Alberta, is owned by TransAlta Utilities Corporation and operated by Manalta Coal Ltd. Approximately 2 million tonnes of sub-bituminous coal is supplied annually to the Wabamun Generating Plant. A high water table, high groundwater pressure, and structural folds contribute to stability problems in the fine-grained overburden. Significant increases in coal recovery have been achieved in recent years through improvements in water management and mining methods. Agricultural capability of the post-mining landscape has also been improved following the completion of mining/ reclamation activities. Introduction The Whitewood Mine, located to the north of Lake Wabamun and seventy kilometres west of Edmonton, Alberta, is owned by TransAlta Utilities Corporation and operated by Manalta Coal Ltd. Figure 1 shows the location of the Whitewood Mine with respect to the city of Edmonton. The mine presently supplies two million tonnes annually of sub-bituminous ""C"" coal to the 582-megawatt Wabamun Generating Plant located adjacent to the mine. The area is characterized by a high water table-, rolling coal seams and an overburden that consists of muskeg, clay and various sedimentary layers of sand, gravel and fine-grained sandstone. These distinctive characteristics require careful attention in order to not only meet the coal delivery requirements of the Wabamun Generating Plant but also to do so economically. Historical Background A small-scale underground coal mine was opened in the Wabamun area in 1910 by the Conner Coal Mining Co. Ltd. Underground operations were continued by several operators until 1948 when the Alberta Coal Co. Ltd. opened a strip mine which was subsequently taken over by the Alberta Southern Coal Co. Ltd. in 1951. The small-scale strip opera"

Jan 1, 1985

By Charles Tkaczuk

Key issues ? Process control is a corporate function implemented locally. ? Security and documentation is mandatory requiring standard practices. ? Publish and communicate activities (do not re-invent the wheel). ? Payback metric system for all projects. ? Partnering with vendors based on experience, expertise and joint R&D. ? Focus on phased process control projects and distribution of costs. ? Integration of services and functions. ? Application of global standards. ? Big picture application thinking.

Apr 1, 2005

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By W. B. Morrey

"In recent years, the major effort in detonator development has been concentrated on ""non-electric"" systems. Existing types all involve some form of explosive reaction to transfer ignition energy from outside the borehole to the pyrotechnic delay element contained within the detonator. These may be based on low-energy detonating cords having grained or plasticized explosive cores, shock tube energy transmission principals and explosive gas ignition systems. Each has properties of internal and external effects not present in electric conductors.The MAGNADET System introduces transformer coupling into electric blasting circuits. Safety features with respect to current leakage, stray currents of AC or DC source, electrostatic energy and radio-frequency radiation are comparable to ""non-electric"" systems, with advantages in simplicity, speed of hook-up and range of application.The transformer device used is a small ferrite ring or toroid which is an integral part of each specialized detonator. The detonator legwires form the secondary side of the transformer winding. The primary side is a single wire loop common to all units within the circuit. Power is supplied from a frequency-tuned portable exploder with unique circuit-sensing features.The MAGNADET System is expected to have particular application to shaft sinking, raising and tunnelling where the protective features as well as speed and efficiency are critical factors. Applications of the 'MAGNA' booster in quarries, open pits and longhole deck charges offer control over vibration problems and elimination of surface noise.IntroductionFor many years, electric detonators and electric blasting systems dominated surface and underground applications where controlled delay times were required. Control over the instant of detonation by blasting machines or power-line switches is the major safety feature.Electrical energy exists in many forms. It may originate from many sources. Electrical energy can be difficult to contain. It may enter or escape through a variety of conductive paths. It may fluctuate, concentrate or dissipate to pose a most elusive potential hazard."

Jan 1, 1982

By A. David MacPhail

"Highland Valley Copper is a large volume producer of copper and molybdenum concentrates. Production is by conventional truck and shovel operation combined with an extensive ore handling in-pit crushing and conveying system.Grade of the two orebodies is low at 0.4% copper and 0.007% molybdenum and this demands a production rate in excess of 260 000 tpd at a stripping ratio of 1: 1. Mining cost has to be kept at minimum levels to keep the mine profitable and thus, it is necessary to keep in the forefront: of technology. As well as the in-pit crushing system, the mine has pioneered the use of shovel weighing coupled with a state-of-the-art dispatch system.Maintenance of the equipment is carried out at the on-site mine maintenance shop with assistance from local shops for engine and wheel motor rebuilds and other large jobs such as those requiring stress relieving. Shovel and truck rebuilds are undertaken by mine crews. Both long- and short-term planning is designed and scheduled in the mine engineering section. Outside consultants are used to assist in slope design, reclamation and blasting technology."

Jan 1, 1992

By J. P. Rajot, H. Mouzannar, M. Bost

"The design of rock foundations may need to evaluate shear strength of rock-concrete interface by performing laboratory direct shear tests. A series of tests were carried out on specimens for different values of the spacing free of encapsulating material about the shear plane and different values of normal stress. Different kinds of failure were observed and not necessarily at the rock-concrete interface. The spacing free of encapsulating material appeared to be of significant influence on the test results. A mechanical analysis is presented which illustrate the influence of the loading conditions in the direct shear box on the failure mechanism. INTRODUCTIONThe design of rock foundations subjected to significant lateral loads requires defining the value of the shear strength of the interface between rock and cast in place concrete. Verifying the stability against sliding of strip footings subjected to inclined loads (SETRA, 2009) or concrete gravity dams (CFBR, 2013) are common examples where design modelling approaches imply the shear strength, sometimes the deformation behavior, of the rock-concrete interface, more or less assumed as a failure plane.Defining the behavior of rock-concrete interfaces relates to tribology. Many studies have been conducted to improve the representation of this behavior (e.g., Johnston & Lam, 1989; Kodikara & Johnston, 1994; Gu, Seidel & Haberfield, 2003; Saiang, Malmgren & Nordlund , 2005; Fishman, 2008; Eltervaag, 2013; Gutierrez, 2013), raising many questions. The behavior appeared to be influenced by many factors such as the geometry of the interface which is not planar, the roughness of the natural rock, the rock mineralogy and the concrete formulation. In addition, the study of the shear strength of rock-concrete interfaces involves considering the two different deformation behaviors of both rock and concrete. Finally, the observed failure mechanism is strongly influenced by the initial cohesion due to adhesion between the two materials when concrete is directly cast onto rock."

Jan 1, 2015

By M. Lytle

"The Corbin area of southeastern British Columbia has been a coal mining area since 1908. Byron Creek Collieries Ltd. Has operated its Coal Mountain Mine in this area from 1974 until the present. In February 1981, this company was purchased by Esso Resources Canada Ltd.Coal Mountain is structurally complex and standard computer algorithms are not applicable to model the overturned synclinal structures and faulted bedding surfaces. This paper discusses two approaches used by Esso Resources staff to model the geology of Coal Mountain.The first approach projects digitized cross-section data along trend to develop a large data base which correctly approximates the shape of the structure. The spatial orientation of the structure is corrected by merging the generated data set with drill-hole data. The second approach uses digitized cross-section and bench-plan geology to generate a block model of the coal reserve.HistoryThe Coal Mountain Mine, also known as the Corbin Mine of Byron Creek Collieries Ltd. is located 24 kilometres south of Highway 3 in southeastern B.C.In 1905, two American businessmen recognized the coal potential of the area during a horseback tour. The two businessmen, D.C. Corbin and E.J. Roberts, formed the Corbin Coal and Coke Co. to mine and market coal from their newly acquired 6075 hectares of coal licenses. By 1908, the town of Corbin was under construction, a 22.4-km rail spur was constructed from the mine to the main CPR line and the first underground mine began to produce coal. An open-pit operation was also developed at the 1828-metre elevation using a steam shovel loading into rail cars. The company operated continuously until 1935, when a lengthy strike forced suspension of operations.In 1943, the Consolidated Mining and Smelting Company Ltd. (now known as Cominco Ltd.) operated two surface mines to produce coal for its smelters at Kimberley and Trail, B.C. This operation ceased in 1948."

Jan 1, 1982

By G. Grant Smith

In situ bulk density of coal is a variable applied to various aspects of coal resource evaluation, such as compositing ply analyses of coal attributes that are expressed on a weight per cent basis, and determining tonnages from volume estimates. Its value is a function of composition and porosity of the in situ material. When densities of ash-free coal, ash and water are fixed, in situ bulk density of a coaly mix can be expressed as a function of proportionate weight of ash in the mix. Correlations between in situ bulk densities and weight per cent ash contents of coaly mixes have been estimated for four general rank classes of coal (low medium volatile bituminous, high volatile bituminous, subbituminous, and lignitic).

Jan 1, 1991

By H. Deveci, E. Y. Yazici, A. D. Bas

The leach solutions of waste of printed circuit boards (WPCB) may contain a wide range of base and precious metals with different concentrations due to heterogeneity of these wastes in composition. Therefore, selection of a suitable metal recovery method is of practical importance for downstream processing of pregnant leach solutions of WPCB. Sulphuric acid leaching of WPCB in the presence of a suitable oxidant is capable of dissolving base metals as well as precious metals such as silver. In this study, cementation of silver from sulphuric acid leach solutions of WPCB using metallic copper, aluminum and zinc was studied. The WPCB sample was assayed to have a silver content of 694 g/t. A synthetic leach solution containing 20 mg/L Ag in sulphuric acid solution (0.51 M H2SO4) was prepared based on the silver concentration in pregnant leach solutions of oxidative sulphuric acid leaching tests. Total sulphate concentration ([SO4 2-]T) was kept constant using sodium sulphate at 1 M. Metallic powders of copper (-850 +600 µm), aluminum (-425 +45 µm) and zinc (-45 µm) were used in the cementation tests. The effects of metal type (Cu, Al or Zn), dosage of metal powders (above the stoichiometric ratio by up to 2000-fold) and temperature (20-80°C) on the rate and extent of silver extraction from the solution was investigated. The effect of presence of copper on the cementation performance was also tested. Under suitable conditions high silver recoveries (>90%) was achieved using metallic copper and zinc while aluminum yielded the lowest silver recovery (i.e. 40% Ag). The kinetics of cementation by zinc was comparatively higher than that of other metals. Increasing the temperature was observed to significantly enhance both the rate and extent of silver cementation. SEM-EDS studies were performed to characterise the metallic powders after cementation.

Jan 1, 2016

By John H. Fowler

"Barytes is one of the major components of drilling fluids used in oil and gas well-drilling. This mineral's close association with the petroleum industry bestows it with a commodity status not enjoyed by many other industrial minerals. Approximately 85% of world barytes production is used as a weighting agent in oil and gas well drilling while the remaining 15% is consumed mainly in the manufacture of barium chemicals, glass and as a pigment, filler or extender.Barytes mining began in Nova Scotia around 1865 and has continued until the present. Currently there are three barytes producers in the province one exporting pharmaceutical-grade barium sulphate and the other two supplying drilling mud-grade barytes to the offshore. Several barytes exploration and development programs are underway with excellent possibilities that Nova Scotia deposits will supply a significantly larger share of the drilling mud-grade barytes used in east coast drilling programs.Currently there is renewed interest in barytes activities in Nova Scotia because of its use as a weighting agent in drilling flu ids used in offshore oil and gas drilling programs.This paper reviews the use of barytes by the well drilling industry; outlines the history of barytes mining in the province, progressing to present-day exploration, development and production activities underway in Nova Scotia; and concludes with the market potential for Nova Scotia barytes."

Jan 1, 1986

By M. Isac, R. I. L. Guthrie, S. Ge

The Al-Mg-Sc-Zr alloys have shown exceptional potential as structural materials for transportation applications. These alloys have proved to be good candidates to be processed as thin strips via the Horizontal Single Belt Casting (HSBC) process. The HSBC process is a near-net-shape casting technology, which involves casting molten metal directly into thin strips, close to the final product thickness, at high cooling rates. It offers an efficient, economical and environmentally-friendly approach to the production of metal strips. Fluid mechanics and associated heat transfer are important aspects of any casting process, and the novel HSBC process is no exception. Three dimensional Computational Fluid Dynamics (CFD) simulations using ANSYS FLUENT 14.5 were performed, in order to assess the importance and effects of the various operational conditions of the HSBC process. This enabled process parameter optimization. Numerical predictions were validated against experimental casting results.

Jan 1, 2014

By Peter N. Calder

Long range mine planning involves developing a mining sequence that schedules the extraction of the ore and waste materials within a final pit limit. The objective is to define a sequence that best meets the defined strategic objectives. The main steps in the creation of an open pit mine plan are the final pit limit design, the design and sequencing of the mining phases, equipment selection and operating cost estimation. Flexibility is the key strategic element in developing a mine plan. Planning the extraction sequences and rates for the various mining areas is a challenging and demanding activity. It is often necessary to consider numerous alternative strategies and what if scenarios. The number of alternatives that can be studied with limited manpower and time resources is restricted. In order to investigate strategic aspects of mine planning, a system to generate workable mine plans rapidly is required. The concept of Visual Mine Planning is that the engineer can visualize the current plan, easily change a component of the plan, such as the annual cut-off grade schedule or the production rate within a particular Phase, and immediately see the effect on the mineralogical and cash flows. If the desired result is not achieved, a change is made and the effect is again immediately seen. This paper presents results of research in this area conducted at the Pontificia Universidad Católica de Chile. The work includes the examination of cut-off grade strategy, sequencing, blending, stockpiling and shovel-truck fleet requirements using simulation.

May 1, 2003